Oxidations with potassium permanganate in the presence of fluoride

Summary The titration of ferrous iron in presence of fluoride ions in acid medium gives fleeting end points and erroneous results. A method is deviced to overcome this difficulty by oxidising the ferrous with an excess of KMnO₄ in alkaline medium. After mixing the reactants the excess of KMnO₄ is reduced by an excess of Hg₂ ²⁺ ions in presence of H₂SO₄ and fluoride. The remaining mercurous is then titrated with standard KMnO₄ solution.Part III: Issa, I. M., and M. Hamdy: Z. analyt. Chem. 174, 418 (1960).     

Oxidations with potassium permanganate in the presence of fluoride

Summary Quadrivalent selenium can be determined with fair accuracy by mixing with an excess of KMnO₄ in the presence of 25–75 ml of 2% NaF solution and 4–7 ml of 9 N sulfuric acid. After leaving the reaction mixture for 10–30 minutes the excess KMnO₄ is estimated by one of the following procedures: A) Titration of the excess KMnO₄ with monovalent mercury, B) Adding an excess of Hg₂ ²⁺ solution to react with the excess KMnO₄ followed by titrating the excess mercurous with KMnO₄ solution.Part I: Issa, I. M., and M. Hamdy, Z. analyt. Chem. 172, 94 (1980).     

Oxidation of trivalent cerium with potassium permanganate in alkaline solutions

Summary Oxidation of trivalent cerium with KMnO₄ in alkaline carbonate mixture is not possible owing to the instability of the solution and to the sluggishness of the reaction. Reduction of KMnO₄ with Ce³⁺ solution fails to give quantitative results in absence of telluric acid. Good results are obtained in presence of telluric acid provided that the alkalinity of the reaction medium is not less than 1 N, in order to overcome the effect of acid present in the cerous solution.A method depending upon the oxidation of Ce³⁺ solution with KMnO₄ followed by back titrating excess KMnO₄ with monovalent thallium gives accurate results.     

Oxidation with manganate solutions

Summary The reaction between Tl⁺ solutions and manganate is sluggish. In the titration of Tl⁺ with manganate solution the end points are always attained earlier than the theoretical. When the reaction is accelerated by NaCl and heating to 45–50° C the end points were found to be concordant with the theoretical values. Titration of manganate with Tl⁺ solutions gives accurate results in presence of telluric acid but not in its absence. It is also possible to determine Tl⁺ by oxidation with an excess of K₂MnO₄ using arsenite as a back titrant for excess oxidant.Part III: Issa, I. M., and M. G. E. Allam: Z. analyt. Chem. 175, 103 (1960).     

Nicotinamidoxime as an analytical reagent

Summary Alkaline solutions of nicotinamidoxime containing traces of nickel(II) give a deep blue color on treatment with iodine. At a p_H of 10.5–11.5 in presence of an excess of the amidoxime the color develops almost instantaneously and is stable for at least 24 hrs. The system adheres to Beer's law in the range of 0.3–10 ppm of nickel, and the optimum range for measurement (1 cm cell) is 3–10 ppm of the metal. The color reaction is highly sensitive (spectrophotometric: 0.014 g Ni cm^–2 at 575 nm identification limit: 0.5 g Ni ml^–1; 12 · 10⁶).All the common anions are without any effect excepting CN^– and EDTA which interfere seriously. Interference of Pb²⁺, Bi³⁺, Al³⁺, Ti⁴⁺, Zr⁴⁺ and Th⁴⁺ can be masked by excess tartrate; while in the presence of Cu²⁺, Co²⁺, Zn²⁺, Mn²⁺ and Fe³⁺, the Ni²⁺ is first separated by the anion exchange method of Kraus and Moore ³ and then determined as usual.From the results of polarographic investigations it has been concluded that in alkaline medium nicotinamidoxime is first oxidized possibly to an azo type of compound which interacts with nickel(II) forming the deep blue color.Part II: K. K. Tripathi and D. Banarjea: Z. analyt. Chem. 168, 407 (1959).     

Iodine monochloride end point in the oxidation of thiocyanate by permanganate. Determination of cerium

Summary A new volumetric method for cerium determination based on the quantitative reduction of Ce(SO₄)₂ by excess potassium thiocyanate and titration of the excess with standard KMnO₄ to the ICl end point has been described.Sincere thanks of the authors are due to Professor S. S. Joshi for facilities and kind interest in the work. The award of a U. P. Scientific Research Committee Scholarship to one of us (M.K.J.) is also gratefully acknowledged.     

Oxidations with alkaline permanganate using monovalent thallium for the back titration: Estimation of lead. selenium,tellurium and chromium

Monovalent-thallium can be successfully used for the back titration of KMnO₄ in the course of estimating Pb⁺², Sc⁺⁴, Te⁺⁴ and Cr⁺³.Reduction of KMnO4 with Tl+ in alkaline solution yields MnO₄^-2 which then passes to MnO₂. he end-points are attained late, but in presence of telluric acid the end-point at MnO₂ stage corresonds to the theoretical value. Reduction at the MnO₄^-2 stage can be checked in presence of Ba⁺² ns and good results obtained with 1–1.5N NaOH.     

Oxidations with alkaline permanganate using monovalent thallium for the back-titration: Estimation of trivalent arsenic

In absence of Ba⁺² ions arsenite reduces KMnO₄ in alkaline medium to MnO₂ without the appearance of an inflection at the manganate state. Reduction could be checked at the manganate in presence of 1N NaOH and Ba⁺² equal to 3 times that equivalent to MnO₄^-2 and arsenate, and when dilute arsenite solutions are applied viz.0.02N In absence of Ba⁺² ions the end-points are attained later than the MnO₂ stage except in 2–3N NaOH. In presence of telluric acid good results are obtained at all alkalinities whence reduction is checked at Mn⁺⁴.As⁺³ could be estimated also by mixing with KMnO₄ either in the presence of Ba⁺² ions + 1N NaOH or in absence of Ba⁺² ions + I.5–3N NaOH and back-titrating the excess oxidant with monovalent thallium.     

Sequential distillation of fission-produced radioiodine and radioruthenium from sulfuric acid solutions

Fission-produced ¹³¹I and ¹⁰³Ru radionuclides have been separated sequentially by distillation from H₂SO₄ of controlled chemical composition. The thermal-neutron irradiated uranium trioxide targets were digested in 2M NaOH solution and then, the supernatant solution was acidified to 20% H₂SO₄ with addition of a few drops of H₂O₂ solution. On boiling for 3.5 hours, ≥99.99%¹³¹I was volatilized, passed through 3M H₂SO₄ traps, and then collected in 0.1M NaOH + 0.01% Na₂S₂O₃ solution with a recovery yield of 73.6%. The product radionuclide had high radiochemical and radionuclidic purities. After separation of ¹³¹I, the fission-product solution was acidified to 40% H₂SO₄ acid containing KMnO₄ as an oxidant and boiled for 40 minutes. Ruthenium nuclides were volatilized and collected in 0.1M NaOH solution. Gamma-ray spectrometry showed that the separation and the recovery yields of ¹⁰³Ru were ≥99.99 and 65%, respectively, with ~92% radionuclidic purity, measured immediately after separation. The radionuclides of ¹³²I and ¹⁰⁶Rh were the main contaminants detected in the obtained ¹⁰³Ru product solution. This revised version was published online in July 2006 with corrections to the Cover Date.     

Liquid-crystalline CuII and PdII complexes with nonmesogenic ferrocene-containing β-aminovinyl ketone

New liquid-crystalline heteropolynuclear complexes L₂M (M=Cu²⁺ (2a), Pd²⁺ (2b)) were synthesized by the reactions of C₅H₅FeC₅H₄−C₆H₄NH−C₂H₂−(CO)−C₆H₄OC₁₂H₂₅ (1, LH) with copper(ii) and palladium(ii) acetates. Compound2b was found to possess monotropic nematic and smectic phases;2a exhibits the monotropic nematic phase and a phenomenon of “double melting”. The compositions and structures of compounds1 and2a,b were established by elemental analysis,¹H and¹³C NMR, ESR, and IR spectroscopy. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2, pp. 381–383, February, 1999.     

Electrometric end points in the oxidation of thiocyanate by permanganate. Determination of cerium

Summary Oxidation of thiocyanate by standard permanganate using electrometric end points is shown to be quantitative in 1.5–2.5N HCl medium and in the presence of ICl as catalyst. A method of estimating cerium(IV), based upon its reduction to cerium(III) by excess KSCN and potentiometric titration of the excess against KMnO₄, is also described.Sincere thanks of the author are due to Prof. S. S. Joshi for research facilities.     

2-Mercapto-benzimidazole as an analytical reagent

Summary Palladium is quantitatively precipitated at aPH 5.0 to 10.1 by 2-mercapto-benzimidazole and the complex, Pd(C₇H₅N₂S)₂, which is found to be diamagnetic, is stable up to a temperature of 447 C. In presence of EDTA and tartrate or citrate and at aPH between 6 and 8, it is separated from alkalis, alkaline earths, Mg, Fe³⁺, Cr, Th, Zr, Ti, UO₂ ²⁺, Be, Ce³⁺, Ce⁴⁺, rare earths, Zn, Mn, Ni, Co, Pb, Bi, As, Sb³⁺, Sn⁴⁺, Tl⁺, Cu²⁺, Cd, Ir⁴⁺, Rh³⁺, Ru³⁺, Os⁴⁺, CrO₄ ^2–, MoO₄ ^2–, WO₄ ^2–, VO₃ ^–, PO₄ ^3– and AsO₄ ^3–. Pb, Ag and Hg²⁺ are kept in solution by potassium iodide while a small amount of Au³⁺ by thiosulphate. The palladium complex is either weighed after drying at 110 C or dissolved in a cyanide solution and determined volumetrically by back titrating the excess cyanide with a standard silver nitrate solution.     

Spectrophotometric determination of osmium

Summary m-Amino benzoic acid in large excess reacts with tetra-, hexa- and octavalent osmium at theph range 4.5–6 to give a purple complex having absorption maximum at 500 nm. Beer's law is obeyed for 0.5 to 8 ppm of osmium(VI) and osmium(VIII) with optimum concentration range of 2 to 8 ppm of osmium(VI) and 3 to 8 ppm for osmium(VIII). The per cent relative error per 1% absolute photometric error is 2.8 for both osmium(VI) and osmium(VIII). Ions such as Pd²⁺, Rh³⁺, Ir⁴⁺, W⁶⁺, U⁶⁺, Co²⁺, Hg²⁺, Mg²⁺, Ca²⁺, Ba²⁺, Sr²⁺, Th⁴⁺ and Zr⁴⁺ do not interfere in the determination.Molar ratio method indicates that the reagent first reduces osmium (VIII) and osmium(VI) to osmium(IV), which then probably forms a 11 complex with the excess unoxidised reagent.Part III.: Anal. chim. Acta 22, 306 (1960); cf. Z. analyt. Chem. 177, 291 (1960).     

Bismuthiol II as an analytical reagent

Summary Lead was estimated as Bismuthiol II complex of composition (C₈H₅N₂S₃)₂Pb by precipitating it from its chloride or nitrate solution in presence of a mineral acid, acetic acid, tartrate or cyanide. The estimation is quantitative up to a maximumph of about 6.5. The lead-Bismuthiol II complex is stable up to about 311° C and the conversion factor is 0.315. The method affords a complete separation of lead from alkalis and alkaline earths, Be²⁺, Mg²⁺, Zn²⁺, Mn²⁺, Co²⁺, Ni²⁺, Fe²⁺, Fe³⁺, Cr³⁺, Al³⁺, rare earths, Ti⁴⁺, Zr⁴⁺, Th⁴⁺, UO₂ ²⁺, Pd²⁺, As³⁺, Sb³⁺, Cl^–, SO₄ ^2–, PO₄ ^3–, AsO₄ ^3–, MoO₄ ^2– and WO₄ ^2–. Among the sulphide group members Ag⁺, Au³⁺, Hg⁺, Hg²⁺, Tl⁺, Tl³⁺, Cd²⁺ and platinum metals, except Pd²⁺, interfere while oxidising agents decompose the excess reagent. Bi³⁺, Cu²⁺ and Sn²⁺, do not interfere up to a maximum limit of 30 mg, 50 mg, and 250 mg respectively.Part I: see Z. analyt. Chem. 154, 262 (1957).     

New cobalt and iron pivalate complexes with 2,2′:6′,2″-terpyridine: synthesis, structure, and magnetic properties

The mononuclear complexes (η³-terpy)M(Piv)²·MeCN (M = Fe ⁱⁱ (3) and Co ⁱⁱ (4), and Piv is the pivalate anion) were synthesized by the reactions of polymeric iron(ii) and cobalt(ii) pivalates with 2,2′:6′,2″-terpyridine (terpy). The oxidation of compound 3 affords the pentanuclear heterospin iron(ii,iii) complex (η³-terpy)Fe₅(μ₄-O)(μ₃-OH)(μ-OH)₂(μ-Piv)₇(η¹-Piv)₂ (5). All compounds were characterized by X-ray diffraction. Dedicated to the 90th anniversary of the L. Ya. Karpov Institute of Physical Chemistry. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1186–1190, June, 2008.     

Bis-salicylaldehyde-ethylenediamine as an analytical reagent

Summary Copper has been determined gravimetrically as its bis-salicylaldehyde-ethylenediamine complex of the composition C₁₆H₁₄O₂N₂ · Cu, dried at 100–120° C. The complex is completely precipitated in theph range of 10.5–13.5, adjusted with ammonia or caustic alkali. It is stable in presence of excess ammonia, 0.1 N alkali, ammonium salts and complexing agents as tartrate, citrate, sodium-thiosulphate, fluoride, thiourea, triethanolamine and EDTA. In presence of tartrate and ammonia the ions of alkali metals, alkaline earths, Ag⁺, Tl⁺, Tl³⁺, Pb²⁺, Cd²⁺, Co²⁺, Mn²⁺, Pd²⁺, Al³⁺, Cr³⁺, La³⁺, Ce³⁺, Au³⁺, Pt⁴⁺, Ti⁴⁺, Zr⁴⁺, Th⁴⁺, UO₂ ²⁺ and anions as VO₃ ^–, MoO₄ ^2–, WO₄ ^2–, CrO₄ ^2–, PO₄ ^3–, AsO₄ ^3– do not interfere. Ni²⁺ and Hg²⁺ are masked by tartrate, EDTA and ammonia; As³⁺, Sb³⁺ and Sn²⁺ are separated using fluoride as the complexing agent; at an alkalinity of 0.1 N caustic alkali in presence of tartrate As³⁺, Sb³⁺, Sn²⁺, Bi³⁺, Zn²⁺ and Fe³⁺ are separated. Fe³⁺ can also be separated using triethanolamine as the masking agent at aph of about 13.0. Copper can be separated from almost all the ions, thus affording a highly selective method for the determination of copper.

---

Zusammenfassung Es wird eine gravimetrische Methode zur Bestimmung von Kupfer beschrieben, die auf der Bildung des Bis-salicylaldehyd-äthylendiaminkomplexes beruht. Dieser hat die Zusammensetzung C₁₆H₁₄O₂N₂ · Cu. Die Fällung wird imph-Bereich 10,5–13,5 (mit Ammoniak oder Alkalilauge eingestellt) vorgenommen und der Niederschlag bei 100°–120° C getrocknet. Der Komplex ist beständig in Gegenwart von überschüssigem Ammoniak, 0,1 n Alkali, Ammoniumsalzen sowie Tartrat, Citrat, Natriumthiosulfat, Fluorid, Thioharnstoff, Triäthanolamin und ÄDTA. In Gegenwart von Tartrat und Ammoniak stören nicht: Alkalien, Erdalkalien, Ag⁺, Tl⁺, Tl³⁺, Pb²⁺, Cd²⁺, Co²⁺, Mn²⁺, Pd²⁺, Al³⁺, Cr³⁺, La³⁺, Ce³⁺, Au³⁺, Pt⁴⁺, Ti⁴⁺, Zr⁴⁺, Th⁴⁺, UO₂ ²⁺ sowie VO₃ ^–, MoO₄ ^2–, WO₄ ^2–, CrO₄ ^2–, PO₄ ^3– und AsO₄ ³⁺. Ni²⁺ und Hg²⁺ können mit Tartrat, ÄDTA und Ammoniak maskiert werden, As³⁺, Sb³⁺ und Sn²⁺ mit Fluorid. In 0,1 n ätzalkalischer Lösung in Gegenwart von Tartrat können As³⁺, Sb³⁺, Sn²⁺, Bi³⁺, Zn²⁺ und Fe³⁺ abgetrennt werden. Fe³⁺ kann ebenfalls mit Triäthanolamin beiph 13,0 maskiert werden. Das beschriebene Verfahren erlaubt somit eine Abtrennung des Kupfers von fast allen anderen Ionen.

---

---

Part I: Singh, B. R., and S. Kumar: Z. analyt. Chem. 185, 211 (1962).     

Fluoride-cation interactions in the formation and stability of apatites

The effect of fluoride, F^-, on the formation and stability of the apatites, with and without the simultaneous presence of some cations M* (M* = Al³⁺, Mg²⁺, Sr²⁺ or Zn²⁺) in the solution were investigated.The preliminary findings were: (a) the cations, M*, when present in low levels in solution, had negative effects on the properties of apatite e.g., caused lower crystallinity, lower Ca/P ratios, higher HPO₄/PO₄, and higher extent of dissolution in an acid buffer; (b) when only F^- ions were present in the precipitation solution, F in the apatite formed had positive effect: greater crystallinity, higher Ca/P, lower HPO₄/PO₄, lower extent of dissolution; and (c) the simultaneous presence of F with the cations, M*, minimized their negative effects and suppressed the formation of Mg-substituted β-TCP.These preliminary results suggest that in biological systems, the simultaneous presence of F^- ions with aluminum, magnesium, strontium or zinc ions will minimize the otherwise negative effects of these cations on the formation and stability of the biological apatites (enamel, dentin, bone mineral).     

Analytical aspects of some organic acids Part III

Summary m-Phenylenedioxydiacetic acid gives a white precipitate with thorium even in the absence of an electrolyte which is quantitative up toph 4. Be²⁺, Mg²⁺, Ca²⁺, Zn²⁺, Pb²⁺ and Mn²⁺ ions are removed by single precipitation and Al³⁺, UO₂ ²⁺ and trivalent cerite earth ions are removed by double precipitation. Sn²⁺, Sn⁴⁺ and Cr³⁺ ions interfere.Part II: See. Z. analyt. Chem.165, 343 (1959).     

Titration of AsO43? ions with 0.1 M magnesium sulphate solution in the presence of Ca2+, Mg2+, Fe3+, Cu2+ ions and some other foreign substances

Summary For the convenient and sufficiently accurate determination of AsO₄ ^3– ions in technical products containing different filling, suspending and colouring materials, as well as impurities—e.g. for the assay of arsenate containing plant protecting materials—the following procedure is recommended.About 5 g of the sample is dissolved, resp. extracted with 4 N hydrochloric acid, and aliquots of the clear filtrate are titrated after elimination of the interfering metal ions by combining them with complexing agents (potassium cyanide and disodium ethylenediamin tetraacetic acid) in a properly buffered medium. The titration with 0.1 M MgSO₄ solution is conducted in the presence of eriochrome black T solution as indicator, first time for eliminating the excess of EDTA added, and afterwards to determine the AsO₄ ^3– ions, after adding about 40% of ethanol.The procedure may be useful chiefly for serial routine analyses.The authors are indebted to engineer L. Fokássy, department leader at the State Institute for Agricultural Quality Control, as well as to engineeress P. Fodor and Mr. Gy. Josepovits, scientific collaborators of the Research Institute for Plant Protection, for kindly supplying some of the samples for the experiments.