Conductivity enhancement of PEDOT:PSS film via sulfonic acid modification: application as transparent electrode for ITO-free polymer solar cells

3-Hydroxy-1-propanesulfonic acid(HPSA)was applied as a modification layer on poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate)(PEDOT:PSS)film via spin-coating,resulting in a massive boost of the conductivity of PEDOT:PSS film,and thus the as-formed PEDOT:PSS/HPSA bilayer film was successfully used as a transparent electrode for ITO-free polymer solar cells(PSCs).Under the optimized concentration of HPSA(0.2 mol L~(-1)),the PEDOT:PSS/HPSA bilayer film has a conductivity of 1020 S cm~(-1),which is improved by about 1400 times of the pristine PEDOT:PSS film(0.7 S cm~(-1)).The sheet resistance of the PEDOT:PSS/HPSA bilayer film was 98Ωsq~(-1),and its transparency in the visible range was over 80%.Both parameters are comparable to those of ITO,enabling its suitability as the transparent electrode.According to atomic force microscopy(AFM),UV-Vis and Raman spectroscopic measurements,the conductivity enhancement was resulted from the removal of PSS moiety by methanol solvent and HPSA-induced segregation of insulating PSS chains along with the conformation transition of the conductive PEDOT chains within PEDOT:PSS.Upon applying PEDOT:PSS/HPSA bilayer film as the transparent electrode substituting ITO,the ITO-free polymer solar cells(PSCs)based on poly[N-9″-hepta-decanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)]:[6,6]-phenyl C71-butyric acid methyl ester(PC_(71)BM)(PCDTBT:PC_(71)BM)active layer exhibited a power conversion efficiency(PCE)of 5.52%,which is comparable to that of the traditional ITO-based devices.     

Improved photovoltaic performance from high quality perovskite thin film grown with the assistance of PC<Subscript>71</Subscript>BM

The strategy of sequentially spin-coating a perovskite film from the perovskite precursor and an electron transporting layer of [6,6]-phenyl-C₇₁-butyric acid methyl ester (PC₇₁BM) is developed to simplify the fabrication procedure of perovskite solar cells. X-ray diffraction and scanning electron microscopy indicate that PC₇₁BM film on perovskite layer can retard the evaporation of dimethyl sulfoxide (DMSO) efficiently, thus prolonging the transformation of intermediate phase to perovskite crystals, leading to a high quality perovskite thin film. The solar cells with the structure of indium tin oxides (ITO)/poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)/CH₃NH₃PbI₃/PC₇₁BM/bathocuproine (BCP)/Ag made from this simplified method exhibit a higher efficiency (12.68%) than those from the conventional one-step method (9.49%).     

聚(3-己基噻吩)作为光谱增感层在有机太阳电池光谱响应增强中的应用

报道了利用聚(3-己基噻吩)(P3HT)作为前置缓冲层来弥补(4,8-双-(2-乙基己氧基)-苯并[1,2-b:4,5-b']二噻吩)-(4-氟代噻并[3,4-b]噻吩(PBDT-TT-F):[6,6]-苯基-C₆₁-丁酸甲酯(PC₆₁BM)共混体相异质结(BHJ)电池对450-600 nm处光谱响应不足的新的器件结构设计思路. 光谱带隙为1.8 eV的PBDT-TT-F 在550-700 nm处有很强的光谱吸收, 在有机太阳电池器件上有很好的应用潜能. 但其在350-550 nm处的吸收不强, 影响了器件对太阳光谱的利用效率. 与此相比, P3HT薄膜的光谱吸收主要在450-600 nm范围内, 同PBDT-TT-F 形成良好的互补关系. 新设计的器件外量子效率(EQE)研究结果表明, 利用P3HT 作为前置缓冲层可以与PBDT-TT-F:PC₆₁BM薄膜中的PC₆₁BM形成平面异质结, 从而拓展了器件在450-600 nm处的光谱响应范围,实现光谱增感作用. 优化P3HT的厚度为20 nm左右, 器件对外输出的短路光电流密度从11.42 mA·cm^-2提高到12.15 mA·cm^-2, 达到了6.3%的提升.     

Improving the performance of polymer solar cells by efficient optimizing the hole transport layer-graphene oxide

Graphene oxide (GO) materials have emerged as a promising alternative for hole transport layer (HTL) in polymer solar cells (PSCs) due to their unique structures and properties. However, insulating properties and eco-contaminative production of GO still need to be solved. Here, we report on the preparation of GO through an improved Hummers method without using NaNO₃, which is an eco-friendly option because it avoids the emissions of NO₂ and N₂O₄ toxic gases. Subsequently, the GO as HTL in PSCs is reduced by simple heat treatment of different temperatures in air, and the performance of devices is obviously improved. The FT-IR and XPS spectra show oxygenated functional groups in GO thin films are gradually removed with the increase of annealing temperature, which restores sp² hybridized graphitic structure, and makes the GO thin films more conducive to the charge transfer. The highest power conversion efficiency of PSCs based on the P3HT: PC₇₁BM system with GO as HTL is 3.39%, which approaches that of PSCs with PEDOT: PSS as HTL (3.41%). Moreover, the devices with annealed GO as HTL have better stability compared to devices with PEDOT: PSS.     

Electrochemical deposition of poly[ethylene-dioxythiophene] (PEDOT) films on ITO electrodes for organic photovoltaic cells: control of morphology,thickness, and electronic properties

In this article, controlled changes on morphology, thickness, and band gap of poly[ethylenedioxythiophene] (PEDOT) polymer films fabricated by electrochemical polymerization (potentiostatically) are analyzed. Electropolymerization of the monomer ethylenedioxythiophene (EDOT) was carried out on indium tin oxide (ITO) electrodes, in different dry organic electrolytic media, such as acetonitrile, acetonitrile–dichloromethane, and toluene–acetonitrile mixtures. It was found that electropolymerization kinetics can be controlled by changing the polarity of the electrolytic media, and kinetics is slower for those with low polarity. This fact combined with an accurate control of EDOT monomer concentration and electropolymerization at E_peak/2 potential, allows to control the morphology and thickness of the electropolymerized PEDOT films (E-PEDOT:ClO₄); toluene/ACN (4:1, v/v) and [EDOT]?=?0.3 mM gave the best films for application in organic photovoltaic (OPV) cells. The performance of the E-PEDOT:ClO₄ films was tested on ITO electrodes as anode buffer layer in OPV cells with the configuration ITO/E-PEDOT:ClO₄/P3HT:PC₆₁BM/Field’s metal, where Field’s metal (cathode) is a eutectic alloy that lets to fabricate OPV devices easily and in a fast and economical way at free vacuum conditions. The performance of these devices was compared with an OPV device constructed with a buffer layer anode, prepared using the classical spin coating of PEDOT:PSS on ITO. Results showed that OPV cells fabricated with E-PEDOT:ClO₄ have a slightly increased PV performance.     

Synthesis and characterization of thieno[3,2‐b]thiophene‐isoindigo‐based copolymers as electron donor and hole transport materials for bulk‐heterojunction polymer solar cells

A novel class of thieno[3,2‐b]thiophene (TT) and isoindigo based copolymers were synthesized and evaluated as electron donor and hole transport materials in bulk‐heterojunction polymer solar cells (BHJ PSCs). These π‐conjugated donor‐acceptor polymers were derived from fused TT and isoindigo structures bridged by thiophene units. The band‐gaps and the highest occupied molecular orbital (HOMO) levels of the polymers were tuned using different conjugating lengths of thiophene units on the main chains, providing band‐gaps from 1.55 to 1.91 eV and HOMO levels from ?5.34 to ?5.71 eV, respectively. The corresponding lowest unoccupied molecular orbital (LUMO) levels were appropriately adjusted with the isoindigo units. Conventional BHJ PSCs (ITO/PEDOT:PSS/active layer/interlayer/Al) with an active layer composed of the polymer and PC₇₁BM were fabricated for evaluation. Power conversion efficiency from a low of 1.25% to a high of 4.69% were achieved with the best performing device provided by the D?π?A polymer with a relatively board absorption spectrum, high absorption coefficient, and more uniform blend morphology. These results demonstrate the potential of this class of thieno[3,2‐b]thiophene‐isoindigo‐based polymers as efficient electron donor and hole transport polymers for BHJ PSCs. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

The phase behavior of a polymer‐fullerene bulk heterojunction system that contains bimolecular crystals

Polymer:fullerene blends have been widely studied as an inexpensive alternative to traditional silicon solar cells. Some polymer:fullerene blends, such as blends of poly(2,5‐bis(3‐tetradecylthiophen‐2‐yl)thieno[3,2‐b]thiophene (pBTTT) with phenyl‐c71‐butyric acid methyl ester (PC₇₁BM), form bimolecular crystals due to fullerene intercalation between the polymer side chains. Here we present the determination of the eutectic pBTTT:PC₇₁BM phase diagram using differential scanning calorimetry (DSC) and two‐dimensional grazing incidence X‐ray scattering (2D GIXS) with in‐situ thermal annealing. The phase diagram explains why the most efficient pBTTT:PC₇₁BM solar cells have 75–80 wt % PC₇₁BM since these blends lie in the center of the only room‐temperature phase region containing both electron‐conducting (PC₇₁BM) and hole‐conducting (bimolecular crystal) phases. We show that intercalation can be suppressed in 50:50 pBTTT:PC₇₁BM blends by using rapid thermal annealing to heat the blends above the eutectic temperature, which forces PC₇₁BM out of the bimolecular crystal, followed by quick cooling to kinetically trap the pure PC₇₁BM phase. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

Lithium Polystyrene Sulfonate as a Hole Transport Material in Inverted Perovskite Solar Cells

Despite the exceptional efficiency of perovskite solar cells (PSCs), further improvements can be made to bring their power conversion efficiencies (PCE) closer to the Shockley-Queisser limit, while the development of cost-effective strategies to produce high-performance devices are needed for them to reach their potential as a widespread energy source. In this context, there is a need to improve existing charge transport layers (CTLs) or introduce new CTLs. In this contribution, we introduced a new polyelectrolyte (lithium poly(styrene sulfonate (PSS))) (Li:PSS) polyelectrolyte as an HTL in inverted PSCs, where Li⁺ can act as a counter ion for the PSS backbone. The negative charge on the PSS backbone can stabilize the presence of p-type carriers and p-doping at the anode. Simple Li:PSS performed poorly due to poor surface coverage and voids existence in perovskite film as well as low conductivity. PEDOT:PSS was added to increase the conductivity to the simple Li:PSS solution before its use which also resulted in lower performance. Furthermore, a bilayer of PEDOT:PSS and Li:PSS was employed, which outperformed simple PEDOT:PSS due to high quality of perovskite film with large grain size also the large electron injection barrier (ϕ_e) impeded back diffusion of electrons towards anode. As a consequence, devices employing PEDOT:PSS / Li:PSS bilayers gave the highest PCE of 18.64%.     

Synthesis of polymers containing 1,2,4‐oxadiazole as an electron‐acceptor moiety in their main chain and their solar cell applications

To explore the aptitude of 1,2,4‐oxadiazole‐based electron‐acceptor unit in polymer solar cell applications, we prepared four new polymers (P1–P4) containing 1,2,4‐oxadiazole moiety in their main chain and applied them to solar cell applications. Thermal, optical, and electrochemical properties of the polymers were studied using thermogravimetric, absorption, and cyclic voltammetry analysis, respectively. All four polymers showed high thermal stability (5% degradation temperature over 335 °C), and the optical band gaps were calculated to be 2.20, 1.72, 1.37, and 1.74 eV, respectively, from the onset wavelength of the film‐state absorption band. The energy levels of the polymers were found to be suitable for bulk heterojunction (BHJ) solar cell applications. The BHJ solar cells were prepared by using the synthesized polymers as a donor and PC₇₁BM as an electron acceptor with the configuration of ITO/PEDOT:PSS/polymer:PC₇₁BM (1:3 wt %)/LiF/Al. One of the polymers was found to show the maximum power conversion efficiency of 1.33% with a Jsc of 4.95 mA/cm², a V_oc of 0.68 V, and a FF of 40%, measured using AM 1.5 G solar simulator at 100 mW/cm₂ light illumination. © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Physical mechanisms responsible for the water-induced degradation of PC61BM P3HT photovoltaic thin films

We show that [6,6]-phenyl-C61-butyric acid methyl ester (PC₆₁BM) at the surface of thin film blends of poly(3-hexylthiophene) (P3HT):PC₆₁BM can be patterned by water. Using a series of heating and cooling steps, water droplets condense onto the blend film surface. This is possible due to the liquid-like, water swollen layer of poly(3,4-ethylenedioxythiophene) polystyrene sulfonate. Breath pattern water deformation and subsequent drying on the film surface results in isolated PC₆₁BM structures, showing that migration of PC₆₁BM takes place. This was confirmed by selective wavelength illumination to spatially map the photoluminescence from the P3HT and PC₆₁BM. Within a device, redistribution of the surface PC₆₁BM into aggregates would be catastrophic, as it would markedly alter device performance. We also postulate that repeated volume change of the poly(3,4-ethylenedioxythiophene) polystyrene sulfonate layer by water swelling may be, in part, responsible for the delamination failure mechanism in thin film solar cells devices. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 141–146     

Solution‐processable and thermally cross‐linkable fluorene‐cored triple‐triphenylamines with terminal vinyl groups to enhance electroluminescence of MEH‐PPV: Synthesis,curing, and optoelectronic properties

This study reports the synthesis, curing, and optoelectronic properties of a solution‐processable, thermally cross‐linkable electron‐ and hole‐blocking material containing fluorene‐core and three periphery N‐phenyl‐N‐(4‐vinylphenyl)benzeneamine ( FTV ). The FTV exhibited good thermal stability with T_d above 478 °C in nitrogen atmosphere. The FTV is readily cross‐linked via terminal vinyl groups by heating at 160 °C for 30 min to obtain homogeneous film with excellent solvent resistance. Multilayer PLED device [ITO/PEDOT:PSS/cured‐ FTV /MEH‐PPV/Ca (50 nm)/Al (100 nm)] was successfully fabricated using solution processed. Inserting cured‐ FTV is between PEDOT:PSS and MEH‐PPV results in simultaneous reduction in hole injection from PEDOT:PSS to MEH‐PPV and blocking in electron transport from MEH‐PPV to anode. The maximum luminance and maximum current efficiency were enhanced from 1810 and 0.27 to 4640 cd/m² and 1.08 cd/A, respectively, after inserting cured‐ FTV layer. Current results demonstrate that the thermally cross‐linkable FTV enhances not only device efficiency but also film homogeneity after thermal curing. FTV is a promising electron‐ and hole‐blocking material applicable for the fabrication of multilayer PLEDs based on PPV derivatives. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 000: 000–000, 2012     

Synthesis of three new 1‐(2,6‐diisopropylphenyl)‐2,5‐di(2‐thienyl) pyrrole‐based donor polymers and their bulk heterojunction solar cell applications

A series of three new 1‐(2,6‐diisopropylphenyl)‐2,5‐di(2‐thienyl)pyrrole‐based polymers such as poly[1‐(2,6‐diisopropylphenyl)‐2,5‐di(2‐thienyl)pyrrole] ( PTPT ), poly[1,4‐(2,5‐bis(octyloxy)phenylene)‐alt‐5,5'‐(1‐(2,6‐diisopropylphenyl)‐2,5‐di(2‐thienyl)pyrrole)] ( PPTPT ), and poly[2,5‐(3‐octylthiophene)‐alt‐5,5'‐(1‐(2,6‐diisopropylphenyl)‐2,5‐di(2‐thienyl)pyrrole)] ( PTTPT ) were synthesized and characterized. The new polymers were readily soluble in common organic solvents and the thermogravimetric analysis showed that the three polymers are thermally stable with the 5% degradation temperature >379 °C. The absorption maxima of the polymers were 478, 483, and 485 nm in thin film and the optical band gaps calculated from the onset wavelength of the optical absorption were 2.15, 2.20, and 2.13 eV, respectively. Each of the polymers was investigated as an electron donor blending with PC₇₀BM as an electron acceptor in bulk heterojunction (BHJ) solar cells. BHJ solar cells were fabricated in ITO/PEDOT:PSS/polymer:PC₇₀BM/TiO_x/Al configurations. The BHJ solar cell with PPTPT :PC₇₀BM (1:5 wt %) showed the power conversion efficiency (PCE) of 1.35% (J_sc = 7.41 mA/cm², V_oc = 0.56 V, FF = 33%), measured using AM 1.5G solar simulator at 100 mW/cm² light illumination. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Molecular engineering of conjugated polymers for solar cells and field‐effect transistors: Side‐chain versus main‐chain electron acceptors

Two model polymers, containing fluorene as an electron‐donating moiety and benzothiadiazole (BT) as an electron‐accepting moiety, have been synthesized by Suzuki coupling reaction. Both polymers are composed of the same chemical composition, but the BT acceptor can be either at a side‐chain (i.e., S‐polymer) or along the polymer main chain (i.e., M‐polymer). Their optical, electrochemical, and photovoltaic properties, together with the field‐effect transistor (FET) characteristics, have been investigated experimentally and theoretically. The FET carrier mobilities were estimated to be 5.20 × 10^?5 and 3.12 × 10^?4 cm² V^?1 s^?1 for the S‐polymer and M‐polymer, respectively. Furthermore, polymeric solar cells (PSCs) with the ITO/PEDOT:PSS/S‐polymer or M‐polymer:PC₇₁BM(1:4)/Al structure were constructed and demonstrated to show a power conversion efficiency of 0.82 and 1.24% for the S‐polymer and M‐polymer, respectively. The observed superior device performances for the M‐polymer in both FET and PSCs are attributable to its relatively low band‐gap and close molecular packing for efficient solar light harvesting and charge transport. This study provides important insights into the design of ideal structure–property relationships for conjugate polymers in FETs and PSCs. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Synthesis and photovoltaic properties of alternating conjugated polymers derived from indolo[3,2-<Emphasis Type="Italic">b</Emphasis>]carbazole and thiophene/thieno[3,2-<Emphasis Type="Italic">b</Emphasis>]thiophene-cored benzoselenadiazole

Two alternating narrow band gap (NBG) copolymers derived from 5,11-di(N-9-heptadecanyl)-indolo[3,2-b]carbazole (ICZ) and 4,7-di(thien-2-yl)-2′,1′,3′-benzoselenadiazole (DSeBT) or 4,7-di(thieno[3,2-b]thien-2-yl)-2′,1′,3′-benzoselenadiazole (DTSeBT), were synthesized and named PICZ-DSeBT and PICZ-DTSeBT, respectively. The PICZ-DSeBT shows good solubility in common organic solvent, and the PICZ-DTSeBT is soluble in hot o-dichlorobenzene (ODCB) and not good soluble in chloroform, toluene etc. The chemical structure, molecular weight and fundamental physical properties of the copolymers were characterized by ¹H NMR, gel permeation chromatography (GPC), cyclic voltammetry (CV), thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC) etc. Potential application of the copolymers to be employed as electron donor material and PC61BM ([6,6]-phenyl-C₆₁ butyric acid methyl ester) for photovoltaic solar cells (PSCs), were investigated. PSCs based on the blends of PICZ-DSeBT/PC₆₁BM (w: w; 1: 2) or PICZ-DTSeBT/PC₆₁BM (w: w; 1: 2) with devices configuration as ITO/PEDOT: PSS/blend/Al, show the power conversion efficiencies (PCEs) of 1.06% and 1.52%, with the open circuit voltage (V _oc) of 0.75 V and 0.70 V, short circuit current densities (J _sc) of 3.45 mA/cm² and 5.30 mA/cm² under an AM1.5 simulator (100 mW/cm²) and the photocurrent response on-set wavelength extending up to 760 nm and 800 nm, respectively. It indicates that the NBG copolymers are viable electron donor materials for PSCs.     

Polymer Optoelectronic Devices with High‐Conductivity Poly(3,4‐Ethylenedioxythiophene) Anodes

Abstract

The conductivity of poly(3,4‐ethylenedioxythiophene):polystyrenesulfonate (PEDOT:PSS) film can be enhanced by more than two orders in magnitude by adding a compound with two or more polar groups, such as ethylene glycol (EG), meso‐erythritol (IUPAC name: 1,2,3,4‐tetrahydroxybutane), or 2‐nitroethanol, into the PEDOT:PSS aqueous solution. The mechanism of the increase in conductivity for PEDOT:PSS has been studied using Raman spectroscopy and atomic force microscope (AFM). Here we propose that the change in conductivity is due to the conformational change of PEDOT chains in the film. In untreated PEDOT:PSS films, coil, linear, or expanded‐coil conformations of the PEDOT chains may be present. In treated PEDOT:PSS films, the linear or expanded‐coil conformations may becomes the dominant form for PEDOT chains. This conformational change results in the enhancement of charge‐carrier mobility in the film and leads to enhanced conductivity. The high‐conductivity PEDOT:PSS film is ideal as the electrode for polymer optoelectronic devices. In this article, we report on the fabrication of polymer light‐emitting diodes (PLEDs) and photovoltaic cells (PVs) made using a highly conductive form of PEDOT:PSS as anode, and we demonstrate its performance relative to that of similar device using indium‐tin oxide (ITO) as the anode.     

Anode Engineering of Highly Efficient Polymer Solar Cells Using Treated ITO

ITO substrates were treated with organic solvent cleaning(OSC), SC1 treatment[V(NH₄OH):V(H₂O₂): V(H₂O)=1:1:5], O₂ plasma and UV ozone, respectively. Combined investigations of atom force microscopy(AFM), water contact angle measurements, ultraviolet photoemission spectroscopy(UPS) and X-ray photoemission spectroscopy(XPS) demonstrated that UV ozone treatment could give rise to the smoothest surface, the most hydrophilic property and the highest work function(WF) of ITO due to the removal of hydrophobic C-O impurity from the ITO surface and the enrichments of more oxygen on the ITO surface. When PEDOT:PSS film[(poly(3,4-ethylenedioxy- thiophene):poly(styrene sulfonate)] was deposited on the ITO substrates treated with UV ozone, it showed a lower root-mean- square roughness in AFM images, a higher transmission in UV-Vis transmission spectra and a higher WF in UPS spectra than the PEDOT:PSS films deposited on the ITO substrates treated by other three methods. As a result, the power conversion efficiency of polymer solar cells(PSCs) based on PTB7:PC₇₁BM as an active layer and ITO treated by UV ozone as an anode can reach 8.48% because of the simultaneously improved short circuit current, open circuit voltage and fill factor compared to the PSCs with ITO treated with other three methods.     

Formation of a polycrystalline film of donor material on PEDOT:PSS buffer induced by crystal nucleation

Poly(3,4‐ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is the most popular anode buffer coated on indium tin oxide. It is thought to improve the inorganic–organic contact, but little is known about its role in organic–organic contact. This study addresses the latter issue by examining how the PEDOT:PSS layer affects the crystallization process of the neighboring layer composed of p‐type organic semiconductors in an organic photovoltaic device. Low landing voltage scanning electron microscopic analysis of crystals and aggregates of two donor compounds, tetrabenzoporphyrin (BP) and poly(3‐hexylthiophene) (P3HT), showed that PEDOT:PSS effectively nucleates the crystallization or aggregation of the donor material on its surface to form a uniformly thick film of polycrystalline BP or aggregated P3HT molecules. By contrast, a graphitic surface cannot induce structural order of the donor molecules on it. This result implies that pinning of the donor molecules to the acidic PEDOT:PSS surface promotes the heterogeneous nucleation at the organic–organic interface. © 2014 Wiley Periodicals, Inc. J. Polym. Sci. Part B: Polym. Phys. 2014 , 52, 833–841     

Synthesis and characterization of indenofluorene‐based copolymers containing 2,5‐bis(2‐thienyl)‐N‐arylpyrrole for bulk heterojunction solar cells and polymer light‐emitting diodes

Two novel alternating π‐conjugated copolymers, poly[2,8‐(6,6′,12,12′‐tetraoctyl‐6,12‐dihydroindeno‐[1,2b]fluorene‐ alt‐5(1‐(2,6‐diisopropylphenyl)‐2,5‐di(2‐thienyl)pyrrole) ( P1 ) and poly[2,8‐(6,6′,12,12′‐tetraoctyl‐6,12‐dihydroindeno‐[1,2b]fluorene‐ alt‐5(1‐(p‐octylphenyl)‐2,5‐di(2‐thienyl)pyrrole) ( P2 ), were synthesized via the Suzuki coupling method and their optoelectronic properties were investigated. The resulting polymers P1 and P2 were completely soluble in various common organic solvents and their weight‐average molecular weights (M_w) were 5.66 × 10⁴ (polydispersity: 1.97) and 2.13× 10⁴ (polydispersity: 1.54), respectively. Bulk heterojunction (BHJ) solar cells were fabricated in ITO/PEDOT:PSS/polymer:PC₇₀BM(1:5)/TiO_x/Al configurations. The BHJ solar cell with P1 :PC₇₀BM (1:5) has a power conversion efficiency (PCE) of 1.12% (J_sc= 3.39 mA/cm², V_oc= 0.67 V, FF = 49.31%), measured using AM 1.5 G solar simulator at 100 mW/cm² light illumination. We fabricated polymer light‐emitting diodes (PLEDs) in ITO/PEDOT:PSS/emitting polymer:polyethylene glycol (PEG)/Ba/Al configurations. The electroluminescence (EL) maxima of the fabricated PLEDs varied from 526 nm to 556 nm depending on the ratio of the polymer to PEG. The turn‐on voltages of the PLEDs were in the range of 3–8 V depending on the ratio of the polymer to PEG, and the maximum brightness and luminance efficiency were 2103 cd/m² and 0.37 cd/A at 12 V, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3169–3177, 2010     

Synthesis of π‐conjugated copolymers composed of benzo[2,1,3]thiadiazole and thiophene units bearing various alkyl groups and their application to photovoltaic cells

π‐Conjugated polymers, PTOTBT , PTEHTBT , and PTt‐BTBT , composed of benzothiadiazole as an electron accepting unit and terthiophene as an electron donating unit in the backbone were prepared. PTOTBT , PTEHTBT , and PTt‐BTBT contained side chain groups of n‐octyl, 2‐ethylhexyl, and t‐butyl groups, respectively. Solubility, optical and thermal properties of the polymers showed strong dependences on their side chain groups. PTEHTBT having 2‐ethylhexyl groups in the side chain exhibited absorption maximum (λ_max) at longer wavelength (565 nm) than PTOTBT (534 nm) and PTt‐BTBT (495 nm). PTOTBT showed higher thermal stability than the others. The prepared polymers were employed to polymer solar cells (PSCs) with a configuration of ITO/PEDOT‐PSS/polymer: PC₆₁BH/LiF/Al. Power conversion efficiency of the PSC‐based on PTEHTBT was 1.32%. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Poly((2‐alkylbenzo[1,2,3]triazole‐4,7‐diyl)vinylene)s for organic solar cells

Poly((2‐Alkylbenzo[1,2,3]triazole‐4,7‐diyl)vinylene)s (pBTzVs) synthesized by Stille coupling show different absorption spectra, solid‐state morphology, and photovoltaic performance, depending on straight‐chain versus branched‐chain (pBTzV12 and pBTzV20) pendant substitution. Periodic boundary condition density functional computations show limited alkyl pendant effects on isolated chain electronic properties; however, pendants could influence polymer backbone conjugative planarity and polymer solid film packing. The polymers are electronically ambipolar, with best performance by pBTzV12 with hole and electron transport mobilities of 4.86 × 10^?6 and 1.96 × 10^?6 cm² V^?1 s^?1, respectively. pBTzV12 gives a smooth film morphology, whereas pBTzV20 gives a very different fibrillar morphology. For ITO/PEDOT:PSS/(1:1 w/w polymer:PC₇₁BM)/LiF/Al devices, pBTzV12 gives power conversion efficiency (PCE) up to 2.87%, and pBTzV20 gives up to PCE = 1.40%; both have open‐circuit voltages of V_OC = 0.6–0.7 V. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1539–1545