碱性鲁米诺体系在玻碳和铂电极上的电位分辨电致化学发光研究

提出一种使用循环伏安（ＣＶ）扫描电位下的电致化学发光（ＥＣＬ）研究方法,在自制的仪器系统中同时进行ｉ－Ｅ和Ｉ－Ｅ测量,获得对应的ＣＶ和电位分辨的电致化学发光（ＰＲＥＣＬ）曲线。首先发现碱性鲁米诺体系在玻碳电极（ＧＣＥ）上呈现２个阳极发光峰（在０．３２Ｖ、０．３９Ｖｖｓ．Ａｇ）和１个阴极发光峰（在－０．６２Ｖ）,在Ｐｔ电极上呈现２个阳极发光峰（在０．４９Ｖ、０．７５Ｖ）。结合ＣＶ、一阶微分伏安、Ｃｌ     

Co-immobilization of polymeric luminol,iron(II) tris(5-aminophenanthroline) and glucose oxidase at an electrode surface,and its application as a glucose optrode

The anodic polymerization of 3-aminophthalhydrazide (luminol) and iron(II) tris 5-aminophenanthroline (Fe(phen-NH2)3(2+)) has been reported in this paper. A bilayer electrode was developed based on these polymers and the ITO conductive glass (denoted ITO[Fe(phen-NH2)3(2+)]luminol electrode). This electrode emitted light (lambdaem: 430 nm) as it was brought into contact with H2O2. At pH 10, the resulting electrochemiluminescence (ECL) showed a linear relationship with the concentration of H2O2 in the range of 10 microM(-1) mM. This bilayer electrode also showed an application potential for the detection of glucose after being further modified with glucose oxidase (denoted ITO[Fe(phen-NH2)3(2+)]luminol]GOx electrode). Although the resulting ECL decayed more rapidly in concentrated glucose solutions (e.g., I M) because of the consumption of luminol during use, the decay became less severe in diluted glucose solutions (e.g., 10 mM). According to the flow injection analysis, a linear relationship existed between the ECL and the concentration of glucose from 10(-5)-10(-3) M at pH 9. The detection limit could reach a level of 5 x 10(-5) M at this pH.     

The mechanism of the electrogenerated chemiluminescence of luminol in aqueous alkaline solution

The mechanism of the electrogenerated chemiluminescence of luminol in aqueous alkaline solution based on the rotating ring—disc electrode system is discussed. The disc electrode is maintained at a negative potential and the ring electrode at a symmetrically changing double-step potential. Hydrogen peroxide generated at the disc electrode by the reduction of oxygen is immediately transported to the ring electrode because of electrode rotation. Hydrogen peroxide and luminol are oxidized at the ring electrode during the positive pulse of the double-step potential. These oxidation processes generate a superoxide radical and a luminol radical as intermediates. The luminol radical reacts with the superoxide radical (or oxygen) emitting light.     

Fiberoptic biosensors based on chemiluminescent reactions

The chemiluminescence of luminol in the presence of H₂O₂ has been exploited to develop fiberoptic biosensors associated with flow injection analysis systems. A chlorophenol sensor was developed based on the ability of certain halophenols to enhance the peroxidase-catalyzed luminol chemiluminescence. Horseradish peroxidase immobilized on a collagen membrane was used. Ten chlorophenols have been tested with this chemiluminescent-based sensor. The lower detection limit was obtained with 4-chloro-3-methylphenol and was equal to 0.01 μM. Electrochemiluminescent-based fiberoptic biosensors for glucose and lactate were also developed using glucose oxidase or lactate oxidase immobilized on polyamide membranes. In the presence of oxidase-generated H₂O₂, the light emission was triggered electrochemically by means of a glassy carbon electrode polarized at +425 mV vs a platinum pseudo-reference electrode. The detection limits for glucose and lactate were 150 and 60 pmol, respectively, and the dynamic ranges were linear from 150 pmol to 600 nmol and from 60 pmol to 60 nmol, respectively.     

Apparatus for mechanistic and analytical studies of the electrogenerated chemiluminescence of luminol

A new apparatus based on the rotating ring—disc electrode system is described. The symmetric double-step potential is connected to the ring electrode to oxidize luminol, while the disc electrode is maintained at a negative potential to reduce oxygen to hydrogen peroxide. Because of the electrode rotation, hydrogen peroxide is immediately transported to the ring electrode at which it reacts with luminol oxidation product to emit light. Preliminary electrogenerated chemiluminescence measurements indicate that the intensity of the chemiluminescence of luminol is highly dependent on the ring and disc electrode materials and that some metal ions have a catalytic or inhibitive effect on this luminescence reaction of luminol.     

The enhanced electrochemiluminescence of luminol on the nickel phthalocyanine modified electrode

A glassy carbon electrode (GCE) modified with nickel(II) tetrasulfophthalocyanine (NiTSPc) and Nafion was used for the investigation of the catalytic oxidation of luminol. The modified electrode was found to much more effectively improve the emission of electrochemiluminescence(ECL) of luminol in a solution containing hydrogen peroxide. The enhanced ECL signal corresponded to the catalytic oxidation of both luminol and H(2)O(2) by NiTSPc. Attached Ni(II) on GCE was oxidised to Ni(III) and then used as the catalyst for the chemiluminescence of luminol. The enhanced stability of the ECL signal with Nafion would mainly result from the prevention of the dissolution of NiTSPc and the adsorption of the oxidation product of luminol on the electrode surface. The proposed method enables a detection limit for luminal of 6.0 x 10(-8) mol L(-1) to be achieved in the presence of H(2)O(2) in the neutral solution. The enhanced ECL intensity had a linear relationship with the concentration of luminol in the range of 1.0 x 10(-7)-8.0 x 10(-6) mol L(-1).     

Enhanced electrochemiluminescence from luminol at multi-walled carbon nanotubes decorated with palladium nanoparticles: a novel route for the fabrication of an oxygen sensor and a glucose biosensor

Incorporation of palladium nanoparticles on the surface of multi-walled carbon nanotubes and modification of glassy carbon electrode with the prepared nano-hybrid material led to the fabrication of a novel electrode. The modified electrode showed attractive electrocatalytic activity and sensitizing effect on luminol-O(2) and luminol-H(2)O(2) electrochemiluminescence (ECL) reactions at neutral media. The sensitized luminol-O(2) and luminol-H(2)O(2) reactions were successfully applied for the ECL determination of dissolved O(2) and glucose, respectively. Under the optimal conditions for luminol-O(2) system, the ECL signal intensity of luminol was linear with the concentration of dissolved oxygen in the range between 0.08 and 0.94 mM (r=0.9996) and for luminol-H(2)O(2) system, the ECL signal intensity of luminol was linear with the concentration of glucose in the range between 0.1 and 1000 μM (r=0.9998). The limits of detection (S/N=3) for dissolved oxygen and glucose were 0.02 mM and 54 nM, respectively. The relative standard deviations (RSD) for repetitive measurements of 0.50 mM oxygen (n=10) and 10 μM glucose (n=30) were 3.5% and 0.3%, respectively. Also, under the optimal conditions for luminol-H(2)O(2) system, the ECL signal intensity of luminol was linear with the concentration of H(2)O(2) in the range between 1 nM and 0.45 mM (r=0.9997). The limit of detection (S/N=3) for H(2)O(2) detection was 0.5 nM and the relative standard deviation for repetitive measurements of 10 μM H(2)O(2) (n=10) was 0.8%.     

Synthesis, characterization, and electrochemiluminescence of luminol-reduced gold nanoparticles and their application in a hydrogen peroxide sensor

It was found that chloroauric acid (HAuCl(4)) could be directly reduced by the luminescent reagent luminol in aqueous solution to form gold nanoparticles (AuNPs), the size of which depended on the amount of luminol. The morphology and surface state of as-prepared AuNPs were characterized by transmission electron microscopy, UV/visible spectroscopy, X-ray photoelectron spectroscopy, FTIR spectroscopy, and thermogravimetric analysis. All results indicated that residual luminol and its oxidation product 3-aminophthalate coexisted on the surface of AuNPs through the weak covalent interaction between gold and nitrogen atoms in their amino groups. Subsequently, a luminol-capped AuNP-modified electrode was fabricated by the immobilization of AuNPs on a gold electrode by virtue of cysteine molecules and then immersion in a luminol solution. The modified electrode was characterized by cyclic voltammetry, electrochemical impedance spectroscopy, and scanning electron microscopy. The as-prepared modified electrode exhibited an electrochemiluminescence (ECL) response in alkaline aqueous solution under a double-step potential. H2O2 was found to enhance the ECL. On this basis, an ECL sensor for the detection of H2O2 was developed. The method is simple, fast, and reagent free. It is applicable to the determination of H2O2 in the range of 3x10(-7)-1x10(-3) mol L(-1) with a detection limit of 1x10(-7) mol L(-1) (S/N=3).     

鲁米诺在铂电极上阳极电致化学发光的机理研究

研究了碱性鲁米诺溶液在多晶铂电极上的阳极电致化学发光(ECL)行为,观察到电极的预极化处理和溶解氧跟发光峰强度和峰形有直接关系。结合XPS谱图和Pt,Pt|S~a~d~s修饰电极的循环伏安特性,给出了鲁米诺阳极ECL两个发光通道的可能反应机理:(1)鲁米诺阴离子在表面有新鲜Pt原子的电极上氧化生成鲁米诺自由基,然后迅速与溶液中的氧反应形成0.22V(vs.Ag)处的发光肩峰;(2)电极表面的铂氧化物能加速原子态氧的发生过程,并增大0.60V(vs.Ag)附近ECL主峰的发光强度。     

A chemiluminescence method for the detection of electrochemically generated H2O2 and ferryl porphyrin

Electrochemical formation of H2O2 and the subsequent ferryl porphyrin were examined by measuring luminol chemiluminescence and absorption spectrum using flow-injection method. Emission was observed under the cathodic potential (0.05 V at pH 2.0 and -0.3 V at pH 11.0) by the electrochemical reduction of buffer electrolytes solution but no emission was observed at anodic potentials. Fe(III)TMPyP solution was added at the down stream of the working electrode and was essential for the emission. Removal of dissolved O2 resulted in the decrease of emission intensity by more than 70%. In order to examine the lifetime of reduced active species, delay tubes were used in between working electrode and Fe(III)TMPyP inlet. Experimental results suggested the active species were stable for quite long. The emission was quenched considerably (>90%) when hydroperoxy catalase was added at the down stream of the working electrode whereas SOD had little effect. Significant inhibition of the emission by the addition of alkene at the down stream of the Fe(III)TMPyP inlet was considered as evidence of oxo-ferryl formation. The spectra at reduction potential under aerated condition were shifted to the longer wavelength (>430 nm) compared to the original spectrum of Fe(III)TMPyP (422 nm). All the spectra were perfectly reproduced by a combination of Fe(III)TMPyP and O=Fe(IV)TMPyP (438 nm) spectra. These observations lead to the conclusion that H2O2 was produced first by electrochemical reduction of O2, which then converted Fe(III)TMPyP into O=Fe(IV)TMPyP to activate luminol. The current efficiencies for the formation of H2O2 were estimated as about 30-65% in all over the pH.     

Electrogenerated chemiluminescence of luminol on a gold-nanorod-modified gold electrode

Electrogenerated chemiluminescence (ECL) of luminol on a gold-nanorod-modified gold electrode was studied, and five ECL peaks were obtained under conventional cyclic voltammetry in both neutral and alkaline solutions. Among them, four ECL peaks (ECL-1-4) were also observed on a gold-nanosphere-modified gold electrode, but the intensities of these ECL peaks were enhanced about 2-10-fold on a gold-nanorod-modified gold electrode in neutral solution. One new strong ECL peak (ECL-5) was obtained at -0.28 V (vs SCE) on a gold-nanorod-modified gold electrode in both neutral and alkaline solutions and enhanced with an increase in pH. In strong alkaline solutions, ECL-1 and ECL-2 on a gold-nanosphere-modified electrode were much stronger than those on a gold-nanorod-modified gold electrode, while ECL-3-5 appeared to only happen on a gold-nanorod-modified gold electrode. The emitter of all the ECL peaks was identified as 3-aminophthalate. The ECL peaks were found to depend on the scan direction, the electrolytes, the pH, and the presence of O(2) and N(2). The reaction pathways for ECL-4 have been further elucidated, and the mechanism of the new ECL peak (ECL-5) has been proposed. The results indicate that a gold-nanorod-modified gold electrode has a catalytic effect on luminol ECL different from that of a gold-nanosphere-modified gold electrode, revealing that the shape of the metal nanoparticles has an important effect on the luminol ECL behavior. The strong ECL of luminol in neutral solution obtained on a gold-nanorod-modified electrode may be used for the sensitive detection of biologically important compounds in physiological conditions.     

QUENCHING OF PEROXIDIZED LUMINOL CHEMILUMINESCENCE BY REDUCED PYRIDINE NUCLEOTIDES

Abstract— Reduced pyridine nucleotides were observed to cause a delay as well as a diminution of light emission from peroxidized luminol at pH 6.5. Other reductants were found to have similar effects. Neither superoxide nor hydroxyl radical scavengers quenched chemiluminescence of luminol in the presence of horseradish peroxidase and H₂O₂. A scheme in which reductants such as NADH and NADPH prevent peroxidase from oxidizing luminol to aminophthalate is proposed. Moreover, it is concluded that neither O₂⁻nor OH' play a role in the peroxidation of luminol by horseradish peroxidase.     

Enhanced electrochemiluminescence employed for the selective detection of methyl parathion based on a zirconia nanoparticle film modified electrode

A simple, rapid and sensitive electrochemiluminescence (ECL) sensor was proposed for direct measurements of methyl parathion (MP) based on the strong affinity of a nano zirconia particles (ZrO(2) NPs) modified film on the electrode to the phosphoric group. ZrO(2) NPs, which could provide a larger absorption area to immobilize organophosphorus, was firstly modified on the glassy carbon electrode surface to prepare the proposed ECL sensor (ZrO(2)/GC). Subsequently, the ZrO(2)/GC electrode was scanned from -0.8 to +0.6 V to obtain the background signal at 0.44 V in a luminol/KCl solution. Then, a certain concentration of MP was added to an aqueous solution for 240 s, which was absorbed onto the ZrO(2)/GC electrode surface. Moreover, the MP absorbed on the surface of the ZrO(2)/GC electrode enhanced the ECL signal of luminol in the luminol/KCl solution, which increased with the concentration of MP. As a result, a novel ECL sensor was obtained in a luminol/KCl solution. The MP was determined in the range of from 3.8 × 10(-11) to 3.8 × 10(-6) mol L(-1), with a low detection limit of 1.27 × 10(-11) mol L(-1) (S/N = 3). The proposed ECL sensor performance for MP detection will open a new field in the application of rapid and screen detection of ultra-trace amounts of organ phosphorus pesticides (OPs) of vegetables used in farm markets.     

铂电极在碱性含氧溶液中的预还原处理对鲁米诺电 致化学发光的影响

研究了铂电极的不同预极化处理过程对碱性鲁米诺阳极电致化学发光(ECL)和阳极极化曲线的影响,发现在碱性含氧溶液中预还原处理的铂电极可增强0.22V(vs.SCE)处发光峰强度,且催化产生1.07V(vs.SCE)附近氧气析出过程并伴随产生明显的ECL发光峰;在酸性溶液中预处理电极可抑制这些活性。给出了催化氧气析出的可能作用机理：在碱性溶液中溶解氧还原生成了吸附在铂电极表面的(OH^-)~a~d~s,从而回忆了氧气的析出过程。同时给出了在碱性含氧溶液中预还原的铂电极上两个可能的ECL反应通道：(1)在0.22V鲁米诺阴离子氧化为鲁米诺自由基,然后与溶解氧反应而发光;(2)1.07V处析出的新鲜氧与鲁米诺阴离子反应而发光。     

Modulated potential electrogenerated chemiluminescence of luminol and Ru(bpy) 3 2+

Chemiluminescence emission intensity is modulated by modulating the potential of a working electrode which is used to generate a key species in the electrogenerated Chemiluminescence (ECL) reaction. The emission is monitored synchronously using a lock-in amplifier. The reactions used in the characterization are luminol with hydrogen peroxide and tris(2,2-bipyridyl)ruthenium (II) (or Ru(bpy) ₃ ²⁺ ) with oxalate. Modulation widths of ± 50 mV yield maximum signals for luminol when centered at 0.45 V (vs Ag/AgCl) and for Ru(bpy) ₃ ²⁺ when centered at 1.05 V. The resulting signal decreases with increasing modulation frequency and shows that luminol/H₂O₂ is a faster ECL system than Ru(bpy) ₃ ²⁺ /oxalate. Working curves for luminol and for oxalate have essentially the same linear range and slope with the modulated potential approach as with a DC electrode potential. This approach provides capability for differentiating the analytical signal from constant background emission or stray light.     

Intensification of electrochemiluminescence of luminol on TiO2 supported Au atomic cluster nano-hybrid modified electrode

With TiO(2) nanoparticles as carrier, a supported nano-material of Au atomic cluster/TiO(2) nano-hybrid was synthesized. It was then modified onto the surface of indium tin oxide (ITO) by Nafion to act as a working electrode for exciting the electrochemiluminescence (ECL) of luminol. The properties of the nano-hybrid and the modified electrode were characterized by XRD, XPS, electronic microscopy, electrochemistry and spectroscopy. The experimental results demonstrated that the modification of this nano-hybrid onto the ITO electrode efficiently intensified the ECL of luminol. It was also revealed that the ECL intensity of luminol on this modified electrode showed very sensitive responses to oxygen and hydrogen peroxide. The detection limits for dissolved oxygen and hydrogen peroxide were 2 μg L(-1) and 5.5 × 10(-12) M, respectively. Besides the discussion of the intensifying mechanism of this nano-hybrid for ECL of luminol, the developed method was also applied for monitoring dissolved oxygen and evaluating the scavenging efficiency of reactive oxygen species of the Ganoderma lucidum spore.     

Mechanism of TiO2-assisted photocatalytic degradation of dyes under visible irradiation: photoelectrocatalytic study by TiO2-film electrodes

Photoelectrocatalytic degradation of various dyes under visible light irradiation with a TiO(2) nanoparticles electrode has been investigated to reveal the mechanism for TiO(2)-assisted photocatalytic degradation of dyes. The degradation of both cationic and anionic dyes at different biases, including the change in the degradation rate of the dyes and the photocurrent change with the bias potential, the degraded intermediates, the voltage-induced adsorption of dyes, the accumulation of electrons in the TiO(2) electrode, the effect of various additives such as benzoquinone (BQ) and N,N-dimethyl aniline (DMA), and the formation of active oxygen species such as O(2)(*-) and H(2)O(2) were examined by UV-visible spectroscopy, HPLC, TOC, and spin-trap ESR spectrometry. It was found that the dyes could controllably interact with the TiO(2) surface by external bias changes and charging of dyes. The cationic dyes such as RhB and MG underwent efficient mineralization at negative bias, but the N-dealkylation process predominated at positive bias under visible light irradiation. The discolorations of the anionic dyes SRB and AR could not be accelerated significantly at either negative or positive bias. At a negative bias of -0.6 V vs SCE, O(2)(*-) and dye(*+) were formed simultaneously at the electrode/electrolyte interface during degradation of cationic RhB. In the case of anionic dyes, however, it is impossible for the O(2)(*-) and dye cationic radical to coexist at the electrode/electrolyte surface. Experimental results imply both the superoxide anionic radical and the dye cationic radical are essential to the mineralization of the dyes under visible light-induced photocatalytic conditions.     

Development of a quantitative bio/chemiluminescence spectrometer determining quantum yields: re-examination of the aqueous luminol chemiluminescence standard

We have developed a bio/chemiluminescence spectrometer with a cooled charge-coupled-device (CCD) detector to obtain a quantitative luminescence spectrum as the absolute number of all emitted photons at each wavelength. The integrated area of the spectrum divided by the number of reacted substrate molecules gives the quantum yield. Calibration of the absolute sensitivity of the CCD-spectrometer system was performed by using lasers and a tungsten lamp with calibrated powers as primary light standards, and calibration of the light-collection efficiency of the spectrometer with several kinds of cells for liquid samples was achieved by introducing a simple reference double-plate cell. The reference cell is not convenient for final bio/chemiluminescence measurements but is useful for the calibration because it has well-defined angular dependence of light emission, allowing accurate calculation of the light-collection efficiency. Using this CCD-spectrometer system, we re-examined the quantum yield of aqueous luminol chemiluminescence with H2O2 catalyzed by horseradish peroxidase. The quantum yield was constant for a wide range of luminol concentrations, whereas it changed and had an optimum against H2O2 concentrations. The optimum quantum yield was 1.23(+/-0.20)%, which is in good agreement with previously reported values.     

Comparative studies on electrogenerated chemiluminescence of luminol on gold nanoparticle modified electrodes

Comparative studies on the electrogenerated chemiluminescence (ECL) behavior of luminol on various electrodes modified with gold nanoparticles of different size were carried out in neutral solution by conventional cyclic voltammetry (CV). The results demonstrated that the gold nanoparticle modified electrodes could generate strong luminol ECL in neutral pH conditions. The catalytic performance of gold nanoparticle modified electrodes on luminol ECL depended not only on the gold nanoparticles but also on the substrate. Gold electrode and glassy carbon electrode were the most suitable substrates for the self-assembly of gold nanoparticles. Moreover, the gold nanoparticle modified gold and glassy carbon electrode had satisfying stability and reproducibility and did not need tedious pretreatment of electrode surface before each measurement. It was also found that luminol ECL behavior depended on the size of gold nanoparticles. The most intense ECL signals were obtained on a 16-nm-diameter gold nanoparticle modified electrode. The modified electrode prepared by the self-assembly method exhibited much better catalytic effect on luminol ECL than that prepared by the electrically deposited method. The ECL behavior of luminol on a gold nanoparticle self-assembled gold electrode was also investigated by other transient-state electrochemical techniques, such as chronoamperometry, differential pulse voltammetry, normal pulse voltammetry, and square wave voltammetry. The strongest ECL intensity was obtained under square wave voltammetric condition.     

Potential-dependent chemiluminescence of luminol on the gold electrode modified with ferrocenylalkanethiol self-assembled monolayer

Self-assembled monolayer of ferrocenylundecanethiol (FcC11SH) on gold electrode was used for the potential-dependent catalyst for chemiluminescence of luminol. Ferrocene head groups adsorbed on gold were oxidized to ferricinium cation species electrochemically and catalyzed the chemiluminescence of luminol. As the redox state of ferrocene group can be regulated by electrode potential, chemiluminescence response can also be controlled electrochemically. The presented system was adopted for detection of glucose in the presence of glucose oxidase since the light emission was detected even in the neutral and weak acid solution.