Study and application of a method for the determination of metallic elements by ICP-AES with preconcentration on an active carbon-silica gel microcolumn in a FI system

Using active carbon-silica gel as adsorbent and sodium diethyldithiocarbamate (NaDDTC) as chelating reagent in a flow injection system, an ICP-AES method has been developed for preconcentration and determination of trace metallic elements in high purity rare earth oxides. The experimental parameters such as pH, flow rate, amount of adsorbent, length of reaction coil and eluent acidity were optimized. At pH 4.6 Al,Cr,Cu,Fe,Pb,V,Zn could be preconcentrated, and subsequently determined by ICP-AES. This method can eliminate matrix effects. Its enrichment factors were 8.1–12.6 with detection limits in the ng/mL range and RSD of 2.3–5.0. This method was applied to the analysis of high purity of La₂O₃ and Eu₂O₃ with satisfactory results. Received: 24 April 1997 / Revised: 22 September 1997 / Accepted: 7 October 1997     

Flow injection on-line sorption preconcentration of platinum in a knotted reactor coupled with electrothermal atomic absorption spectrometry

A flow injection on-line sorption preconcentration method for the electrothermal AAS determination of platinum has been developed. The pyrrolidine dithiocarbamate complexes of either Pt⁴⁺ or Pt²⁺, formed in 0.7 mol L^–1 HNO₃, are on-line adsorbed on the inner walls of a PTFE knotted reactor and subsequently eluted with methanol. An enhancement factor of 112 and a detection limit (3 σ) of 10 ng L^–1 along with a sampling frequency of 21 h^–1 are achieved with a 90 s preconcentration time at a sample flow rate of 8.8 mL min^–1. The relative standard deviation is 2.5% for 0.4 μg L^–1 Pt. The method has been applied to the determination of platinum in blood samples. Received: 6 October 1997 / Revised: 26 November 1997 / Accepted: 3 December 1997     

Influence of B<Subscript>2</Subscript>O<Subscript>3</Subscript> on the structure and crystallization of soil active glasses

Glasses of the SiO₂–P₂O₅–K₂O–MgO–CaO–B₂O₃ system acting as nutrients carriers in the soil environment were synthesised by the melt-quenching technique. Thermal properties were studied using DTA/DSC methods and the influence of B₂O₃ and P₂O₅ content on thermal stability and crystallization process of these glasses was examined. The structure of the glass network was characterized by FTIR, ³¹P, and ¹¹B MAS NMR. The chemical activity of the glasses in the 2 mass% citric acid solution was measured by the ICP-AES method. The analysis indicated that the formation of P–O–B units with chemically stable tetrahedral borate groups decreases the glass solubility in conditions simulating the soil environment.     

Indirect atomic absorption spectroscopic determination of SiO2 in copper composite coatings

A fast, sensitive and reliable method for the indirect atomic absorption determination of SiO₂ in copper composite coatings after extraction of silicomolybdic acid in a mixture of isobutyl methyl ketone and butanol (volume ratio 5 : 1) and measurement of the molybdenum absorbance in an air/acetylene flame is described. The experimental conditions are optimized for (i) prevention of the silicon polymerization during sample preparation and storage; (ii) for overcoming of the Cu(SiF₆) – complex formation and (iii) for quantitative extraction of the yellow complex into the organic phase for a wide silicon concentration range. The method permits the determination of 0.5–10 mg/g Si in copper. The analytical performance of the proposed method is compared with direct Si determination using ICP-AES. Received: 15 May 1997 / Revised: 19 September 1997 / Accepted: 25 September 1997     

Sulfur speciation by capillary zone electrophoresis: conditions for sulfite stabilization and determination in the presence of sulfate, thiosulfate and peroxodisulfate

Capillary zone electrophoresis (CZE) was used for the separation of the sulfur species SO₃ ^2–, SO₄ ^2–, S₂O₃ ^2– and S₂O₈ ^2–. Using an electrolyte system with 9.5 mmol L^–1 potassium chromate as UV-absorbing probe and 1 mmol L^–1 diethylenetriamine (DETA) as electroosmotic flow modifier, various possibilities for the stabilization of sulfite and electrophoretic separation of the sulfur anions were investigated. By adding 5% propanol as a stabilizer to both the working electrolyte and the sample solution, a good stabilization for sulfite and a separation of the sulfur anions in a short analysis time (4 min) was achieved. The advantages by using propanol instead of other stabilizers often used in analytical techniques are discussed. The electrophoretic separation of the sulfur anions was optimized with respect to the pH of the working electrolyte and concentration of the electroosmotic flow modifier (DETA). The detection limits achieved for SO₃ ^2–, SO₄ ^2–, S₂O₃ ^2– and S₂O₈ ^2– were 0.35, 0.25, 0.78 and 0.80 mg L^–1, respectively. Received: 16 December 1999 / Revised: 7 March 2000 / Accepted: 14 March 2000     

Determination of total iron in ground waters and multivitamin tablets using a solid-phase reactor with tiron immobilised on amberlite ion-exchange resin in a flow injection system

A method is described for the flow injection determination of total iron as Fe(III) using a solid-phase reactor containing disodium-1,2-dihydroxybenzene-3,5-disulphonate (tiron) as substrate. The iron(III) reacted with tiron to form a complex which absorbs strongly at 667 nm, where it was measured spectrophotometrically. The system has a linear range of 1 to 50 mg L^–1 with a detection limit of 0.67 mg L^–1. It is suitable for the determination of total iron in multivitamin tablets and iron-rich ground waters, with a relative standard deviation of better than 1.1%. The results obtained compared favourably with the certified values and a standard ICP-AES method. Received: 12 November 1997 / Revised: 9 March 1998 / Accepted: 15 March 1998     

Bi5Nb3O15 as a photocatalyst: photocatalytic and photoelectrochemical studies

Bi₅Nb₃O₁₅ was prepared from a stoichiometric mixture of Bi₂O₃ and Nb₂O₅ at 300–500 °C. The prepared photocatalyst was characterized by diffuse reflection spectrum (DRS), X-ray diffraction (XRD), scanning electron microscopy (SEM) and particle size analysis. The band gap, crystal structure and average grain size were determined from the above methods to be 3.25 eV, distorted pyrochlore and 4–5 μm respectively. The photoelectrochemical behavior of hydrogen-reduced Bi₅Nb₃O₁₅ was investigated in 0.1 M Na₂SO₄ and using the Fe(CN)₆ ^3−/4− redox couple for measuring the current-voltage characteristics. The cyclic voltammetric studies revealed that the onset potential for photocurrent generation existed at −0.45 V, which is more negative to water reduction level at pH 7.0, and that of the photocurrent at 1.0 V was observed as 0.58 mA/cm². Photocatalytic hydrogen production has been achieved by using Bi₅Nb₃O₁₅ as a photocatalyst in presence of methyl viologen. The quantum yield for hydrogen production for this system was found to be 0.83. All the studies clearly indicated that Bi₅Nb₃O₁₅ has potential in solar energy conversion. Received: 22 May 1997 / Accepted: 18 September 1997     

Influence of aluminium precursor on physico-chemical properties of aluminium hydroxides and oxides

An attempt to obtain aluminium hydroxide that could give aluminium oxides of increased thermal stability was made. Aluminium hydroxide was precipitated during a hydrolysis of aluminium chloride in ammonia medium. The influence of preparative conditions, such as a dosing rate of aluminium precursor, pH, duration of the precipitate refluxing and temperature of calcination, on the properties of obtained hydroxides and oxides was investigated. The materials were studied with the following methods: thermal analysis, IR spectroscopy, low-temperature nitrogen adsorption and adsorption–desorption of benzene vapours. Precipitated boehmites had high values of S _BET determined from nitrogen adsorption (220–300 m²g^–1), good sorption capacity for benzene vapours, developed mesoporous structure and hydrophilic character. It has been proved that a high pH value during the precipitation of aluminium hydroxide favoured better crystallisation of boehmite structure, higher temperature of its dehydroxylation into γ-Al₂O₃, and delayed transformation of γ phase into α-Al₂O₃. Aluminium oxides derived from the hydroxides precipitated at a high pH were the most stable at high temperatures, and were characterised with the best surface properties. The online version of the original article can be found at     

Rapid removal of anionic organic dye from contaminated water using a poly(3-aminobenzoic acid/graphene oxide/cobalt ferrite) nanocomposite low-cost adsorbent via adsorption techniques

This research study aims to remove hazardous anionic azo dyes (Congo red (CR)) from aqueous solutions via a simple adsorption method using a poly(3-aminobenzoic acid/graphene oxide/cobalt ferrite) nanocomposite (P3ABA/GO/CoFe₂O₄) as a novel and low-cost nanoadsorbent, as synthesized by a simple and straightforward polymerization method. Typically, 3-aminobenzoic acid (3ABA), as monomer, was chemically polymerized with graphene oxide (GO) and cobalt ferrite (CoFe₂O₄) in an aqueous acidic medium containing an ammonium persulfate initiator. The adsorbent P3ABA/GO/CoFe₂O₄ nanocomposite was characterized using various techniques such as Fourier transform infrared spectroscopy, X-ray diffraction, thermogravimetric analysis, transmission electron microscopy, scanning electron microscopy, energy-dispersive analysis by X-ray and Brunauer–Emmett–Teller, vibrating sample magnetometer, and zeta potential techniques. These techniques confirmed the interaction between the poly(3-aminobenzoic acid) with GO and CoFe₂O₄ due to the presence of π-π interactions, hydrogen bonding, and electrostatic forces. Herein, the removal efficiency of dye from aqueous solution by the adsorbent was studied according to several parameters such as the pH of the solution, dye concentration, dosage of adsorbent, contact time, and temperature. The adsorption of the dye was fitted using a Langmuir model (R² between 0.9980 and 0.9995) at different temperatures, and a kinetic model that was pseudo-second order (R² = between 0.9993 and 0.9929) at various initial concentrations of CR dye. In addition, the data revealed that the P3ABA/GO/CoFe₂O₄ nanocomposite exhibited a high adsorption capacity (153.92 mg/g) and removal for CR dye (98 %) at pH 5. Thermodynamic results showed the adsorption process was an endothermic and spontaneous reaction. It was found that, in terms of reusability, the P3ABA/GO/CoFe₂O₄ adsorbent can be used for up to six cycles. In this study, P3ABA/GO/CoFe₂O₄ nanocomposites were found to be low cost, and have an excellent removal capability and fast adsorption rate for CR from wastewater via a simple adsorption method. Moreover, this adsorbent nanocomposite could be simply separated from the resultant solution and recycled.     

Physical-chemistry of sodium silicate gelation in an alkaline medium

The behavior of sodium silicate solutions in an alkaline medium has been studied in the 11.56–9 pH range by adding different amount of hydrochloric acid into a concentrated commercial solution ([Si] = 7 mol/L, Si/Na = 1.71, pH = 11.56). The formed products and their evolution during long ripening (up to 150 days) have been characterized by cryo-SEM, elementary analysis (ICP-AES), X-ray diffraction and surface area and relative density measurements. In the studied narrow ranges of pH (11.56–9) and silicon concentration (7–0.2 mol/L) four different situations have been observed: (i) a stable and clear solution, (ii) a reversible and transparent physical gel; (iii) a soluble white gel characterized by a significant contraction during ripening and (iv) an irreversible gel which presents a slow syneresis leading to a consolidate solid. The characterizations of the different solids, liquids and gels have shown that the observed behaviors were the results of the formation of nanometric soluble NaSi_1.87O_4.24 particles and/or insoluble silica-like (NaSi_12.66O_25.82) grains and of the contribution of a dissolution/precipitation mechanism.     

Sol–gel synthesis,characterization and photocatalytic activity of mesoporous TiO<Subscript>2</Subscript>/γ-Al<Subscript>2</Subscript>O<Subscript>3 </Subscript>granules

Mesoporous TiO₂/γ-Al₂O₃ composite granules were prepared by combining sol–gel/oil-drop method, using various titania solution. The product granules can be used as a photocatalyst or adsorbent in moving, fluidized bed reactors. The phase composition and pore structure of the granules can be controlled by calcination temperature and using different titania solution. In the photocatalysis of NH₃ decomposition, TiO₂/γ-Al₂O₃ granules using Degussa P25 powder treated thermally at 450 °C showed the highest catalytic ability. However, TiO₂/γ-Al₂O₃ granules using titania made by hydrothermal method had comparable performance in NH₃ decomposition.     

Copper determination after FI on-line sorbent preconcentration using 1-nitroso-2-naphthol as a complexing reagent

The suitability of 1-nitroso-2-naphthol as a complexing agent for on-line preconcentration of copper using RP-C₁₈ material in a microcolumn with flow injection coupled with flame atomic absorption spectrometry (FI-FAAS) has been tested. Various parameters affecting complex formation, such as pH, sample flow rate, etc. and its elution into the nebulizer of FAAS were optimized. ?A 5 × 10^–3 mol/L reagent was on-line mixed with aqueous sample solution acidified with 0.1% (v/v) nitric acid ?(pH 3–4) and flowed through the microcolumn for 30 s. The adsorbed complexes in the microcolumn were eluted with ethanol in 10 s into the nebulizer of FAAS. A good precision (1.7% for 50 μg/L copper, n = 12), high enrichment factor (19) with detection limit (3σ) 2.0 μg/L, and sample throughput (90 h^–1) were obtained. The method was applied to certified reference materials seawater, mussel (biological), NBS-362 and NBS-364 (special low alloy steel), for the determination of copper, and the results were in good agreement with the certified values. Received: 4 May 1999 / Revised: 25 June 1999 / Accepted: 29 June 1999     

Determination of ultra-trace amounts of inorganic selenium species in natural water by ion chromatography-inductively coupled plasma-mass spectrometry coupled with nano-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> solid phase extraction

This work presents a nano-Al₂O₃ solid phase extraction technique for the determination of ultra-trace amounts of inorganic selenium species in aqueous systems using ion chromatography inductively coupled plasma-mass spectrometry (IC-ICP-MS). In this experiment, the inorganic selenium species were successfully extracted on a nano-Al₂O₃ solid phase column and then quantitative eluted with a 100 mmol L⁻¹ NaOH solution. Extraction conditions such as solvent identity, solvent concentration, solvent volume, solvent pH and salt addition were optimized. Under the optimum extraction conditions (elute solvent: 100 mmol L⁻¹ NaOH, solvent volume: 4 mL, pH: 7.0), low detection limits (Se (IV): 6 ng L⁻¹, Se (VI): 11 ng L⁻¹; RSD<5.0%) and good linear range (0.5–100 ng mL⁻¹, R² > 0.999) were obtained for all of the analytes. Good spiked recoveries over the range of 80–98% were obtained by applying the proposed method on real environmental water samples. These results indicated that this method is very sensitive and reliable when monitoring trace levels of inorganic selenium species in aqueous samples.      

Adsorption of cationic polyelectrolyte onto a model carboxylic latex and the influence of adsorbed polycation on the charge regulation at the latex surface

 Adsorption of a well-characterized cationic polyacrylamide (CPAM) onto the surface of a model colloid (monodisperse polystyrene latex with carboxylic functional groups) was studied over a wide range of pH (4–9) and KCl concentration (c _s =10^-3–0.3 M). The surface charge density of the latex particles with and without adsorbed CPAM was also measured over the same range of electrolyte compositions. The adsorbed amount of CPAM increases with increase in c _s and pH. The polyelectrolyte adsorption alters substantially the surface charge density of the latex particles as compared to the polymer-free case. A large overcompensation of the surface charge by the adsorbed polyelectrolyte is established at high c _s and low pH. A qualitative explanation of the observed features is put forward. Received: 3 December 1996 Accepted: 20 January 1997     

Anodic stripping voltammetric determination of total lead, copper and selenium in whole blood and blood serum

A two-step procedure including appropriate wet-digestions, separation of selenium from interfering ions such as heavy metal ions with pentyl alcohol and anodic stripping voltammetric (ASV) determination of Pb²⁺, Cu²⁺ and SeO₃ ^2– is developed. The elements in digested whole blood and serum sample solutions were determined by using a standard addition method. 1 × 10^–9 mol/L SeO^2– ₃, Cu²⁺ and Pb²⁺ were successfully determined with relative standard deviations of approximately 1–2% (n = 6–8). Received: 19 August 1996 / Revised: 24 February 1997 / Accepted: 28 February 1997     

Synthesis of the perovskite ceramic Li3xLa2/3–xTiO3 by a chemical solution route using a triblock copolymer surfactant

The synthesis of the perovskite Li_3xLa_2/3–x□_1/3–2xTiO₃ by a chemical solution route, using a triblock copolymer surfactant, PEO_n–PPO_m–PEO_n, is described. This titanate is a non-hygroscopic fast lithium conductor and therefore is a good candidate for electrochemical applications. It is generally prepared by a conventional solid-state reaction (SSR) method. However this synthesis method does not allow the preparation of nanopowders or the formation of thin films. For these special purposes, synthesis by a chemical solution route, with the formation of a polymeric precursor during synthesis, has been investigated. By using the above-mentioned non-ionic surfactant, the preparation of nanopowders of complex oxides can be done. Furthermore, this way of synthesis leads to the formation of an intermediate polymeric precursor which can be easily spread on substrates to obtain films. We show that the formation of a pure phase of the perovskite Li_3xLa_2/3–x□_1/3–2xTiO₃ is highly dependent on the synthesis conditions, namely the presence of water in the solvent, the EO/metal ratio, the Li⁺ content in the precursor and the calcination temperature. The influence of these parameters on the microstructure of the oxide is studied by X-ray diffraction, scanning electron microscopy and granulometry. A powder of Li_3xLa_2/3–x□_1/3–2xTiO₃ (x = 0.10), with an average particles size of 200 nm, has been obtained. The ionic conductivity of this oxide is the same as the one obtained with oxide prepared by SSR (a bulk conductivity of 1.4 × 10⁻³ S/cm at 37 °C). The ceramic obtained from this powder after sintering at 1,150 °C shows a good pH response. This material can then be used as a sensitive membrane in a potentiometric pH sensor. The presence of hydrophobic PPO groups in the polymer precursor allowed preparing films of Li_3xLa_2/3–x□_1/3–2xTiO₃ with a good adherence on Pt substrate. This kind of synthesis is then very promising to prepare micro pH sensors.     

基于静电喷射法活性多孔磁性炭球的制备及其对亚甲基蓝的吸附

在利用静电喷射一步法获得壳聚糖(CS)磁性微球(Fe₃O₄/CS)的基础上,对Fe₃O₄/CS进行高温炭化和碱活化处理获得活性磁性多孔炭球(A-Fe₃O₄/C),并对A-Fe₃O₄/C吸附水中亚甲基蓝(MB)分子的性能进行了研究。在利用扫描电子显微镜、红外吸收光谱仪、比表面分析仪对制备微球的形貌和结构进行分析的基础上,深入研究溶液pH、吸附时间、温度以及活化剂种类等因素对A-Fe₃O₄/C吸附性能的影响。研究结果表明,A-Fe₃O₄/C对MB的吸附量随着pH值的增加而增大,且经KOH活化后的A-Fe₃O₄/C对MB表现出较优的吸附性能。A-Fe₃O₄/C对MB的吸附过程符合伪二级动力学方程和Langmuir等温线模型,理论最大吸附容量可达300.6 mg·g^-1。此外,A-Fe₃O₄/C表现出良好的重复利用性能,6次循环后对MB的去除率没有明显下降。     

Synthesis of maghemite nano-particles and its application as radionuclidic adsorbant to purify <Superscript>109</Superscript>Cd radionuclide

Maghemite nano-particles were synthesized by a solid-state chemical reaction for its highly selective use as, cyclotron-produced, ¹⁰⁹Cd (462.9 days) purification method of choice. ¹⁰⁹Cd radiochemical separation starts with Ag activities precipitated with HCl 0.0015 M followed by, on a second step, ¹⁰⁹Cd separation from Cu carrier and ⁶⁵Zn (243.8 days) using Ca (NO₃)₂ 0.01 M. Experimental parameters such, pH and sorbent concentration, on ¹⁰⁹Cd extraction efficiency were investigated. Phase morphology, nanostructure and size of nano-particles were studied by X-ray diffraction (XRD) and scanning electron microscopy (SEM). A 10–20 nm average grain size was derived from XRD line broadening and SEM data. Heat treatment on Fe³⁺:Fe²⁺ ratios equal to 2:1, produced powders, resulting in tetragonal (maghemite) structure at 300 °C and rhombohedra (hematite) at 600 °C. ¹⁰⁹Cd chemical and radionuclidic purity were determined by ICP-AES and HPGe detector gamma-ray spectrometry. The overall recovery and radionuclide purity were 80.0% from obtained 129.63 kBq/C MeV (70 kBq/μAh) initial activity and 91.4%, respectively.     

Study on synthesis and evolution of sodium potassium niobate ceramic powders by an oxalic acid-based sol–gel method

Potassium sodium niobate (KNN) ceramic powders by a variation of sol–gel method is synthesized. The metal precursors used for the KNN synthesis are potassium carbonate, sodium carbonate and niobium hydroxide, ethylene glycol are used as chelating and esterification agent, respectively. The effects of amount of oxalic acid (OA) and ethylene glycol (EG), pH value on the stability of the precursor sol were investigated. The evolution of (K_0.5Na_0.5)NbO₃ crystal phase was also investigated by XRD, IR, SEM and TG-DTA. The results showed that stable precursor sol was formed when n_(OA):n_(Mn+) = 3:1, n_(OA):n_(EG) = 1:2 and pH value was in the range of 2.5–3.5. Xerogel was sintered in the range of 500–650 °C to prepare K₆Nb_10.88O₃₀ and Na₂Nb₄O₁₁ powder. Then the compound was sintered at 750 °C to produce perovskite (K_0.5Na_0.5)NbO₃ ceramic powders. The grain size is about 100–200 nm.     

Amperometric determination of hydrogen peroxide with a manganese dioxide film-modified screen printed carbon electrode

A carbon thick film electrode modified with an MnO₂-film is investigated as an amperometric detector for hydrogen peroxide in flow-injection analysis (FIA). At an operating potential of +0.48 V vs. Ag/AgCl catalytic oxidation of the analyte is exploited for amperometric monitoring. Experimental parameters, such as pH of the carrier, working potential, flow rate and injection volume, are optimized. The amperometric signals are linearly proportional to the concentration of H₂O₂ in the range from 0.005 to 10 mg/L, showing a detection limit (3σ) of 2.3 μg/L. The method is applied to the determination of H₂O₂ in rain water and to a simple assay to quantify glucose in human plasma. Received: 29 January 1998 / Revised: 4 May 1998 / Accepted: 13 May 1998