含双键大孔径苯乙烯—二乙烯基苯微球的合成与表征

含双键大孔径苯乙烯－二乙烯基苯微球的合成与表征袁青阚成友刘伟良孔祥正＊（山东大学化学系济南２５０１００）关键词苯乙烯－二乙烯基苯共聚树脂，悬浮聚合，树脂微球，复合致孔剂，孔结构１９９７－０７－０３收稿，１９９８－０１－１２修回国家教委留学服务中心回国...     

苯并双噁唑类聚合物的合成

详细介绍了以4,6-二氨基间苯二酚盐酸盐(DADHB)为原料,采用多聚磷酸法、三甲基硅烷基化法、中间相聚合法、单体成盐法合成聚对苯撑苯并双噁唑(PBO),还有以4,6-二硝基间苯二酚(DNR)为原料,先选择还原制得4-氨基-6-硝基间苯二酚盐酸盐,进而与对甲氧羰基苯甲酰氯进行缩环合获得苯并噁唑化合物,再催化加氢合成AB型PBO新单体2-(对甲氧羰基苯基)-5-氨基-6-羟基苯并噁唑,最后自缩聚反应制备PBO的新路线.另外,本文还介绍了直链烯烃型、直链脂肪烷烃型、稠环芳烃型、联苯取代基型、杂环型、聚醚型等苯并双噁唑类聚合物的合成方法.     

Photo-grafting Poly(acrylic acid) onto Poly(lactic acid) Chains in Solution

Poly(lactic acid)(PLA)is one of the most important bio-plastics,and chemical modification of the already-polymerized poly(lactic acid)chains may enable optimization of its material properties and expand its application areas.In this study,we demonstrated that poly(lactic acid)can be readily dissolved in acrylic acid at room temperature,and acrylic acid can be graft-polymerized onto poly(lactic acid)chains in solution with the help of photoinitiator benzophenone under 254 nm ultraviolet(UV)irradiation.Similar photo-grafting polymerization of acrylic acid(PAA)has only been studied before in the surface modification of polymer films.The graft ratio could be controlled by various reaction parameters,including irradiation time,benzophenone content,and monomer/polymer ratios.This photo-grafting reaction resulted in high graft ratio(graft ratio PAA/PLA up to 180%)without formation of homopolymers of acrylic acid.When the PAA/PLA graft ratio was higher than 100%,the resulting PLA-g-PAA polymer was found dispersible in water.The pros and cons of the photo-grafting reaction were also discussed.     

基于聚乳酸的可降解形状记忆高分子的研究进展

综述了基于聚乳酸的可生物降解的形状记忆高分子材料的研究情况。首先介绍了形状记忆高分子材料的记忆效应、记忆机理,然后讨论了基于聚乳酸的三种类型的形状记忆高分子材料：单组份的聚乳酸类、聚乳酸共聚物类以及聚乳酸与无机物的复合材料,分别介绍了各种类型的形状记忆高分子材料的形状记忆性能和生物降解性能。最后,讨论了聚乳酸类记忆材料的应用情况,并对其研究前景和发展趋势进行了展望。     

The Synthesis of Poly(ethylene oxide)-Block-Polybutylacrylate

ＴｈｅＳｙｎｔｈｅｓｉｓｏｆＰｏｌｙ（ｅｔｈｙｌｅｎｅｏｘｉｄｅ）┐Ｂｌｏｃｋ┐Ｐｏｌｙｂｕｔｙｌａｃｒｙｌａｔｅ＊＊ＳｕｐｐｏｒｔｅｄｂｙｔｈｅＮａｔｉｏｎａｌＮａｔｕｒａｌＳｃｉｅｎｃｅＦｏｕｎｄａｔｉｏｎｏｆＣｈｉｎａａｎｄＤｏｃｔｏｒａｌｆｏ...     

Monodisperse micron-sized macroporous poly(styrene-co-divinylbenzene) particles by seeded polymerization

Macroporous poly(styrene-co-divinylbenzene) particles were produced in a micron-size range by two-stage swelling and continuous polymerization. The molecular weight of the polystyrene seed particles was controlled by incorporating a urethane acrylate. It was found that the porosity of the particles produced by the seeded polymerization was dependent on the molecular weight of the seed polymer. As the molecular weight of the polystyrene seed increased, the porous particles produced became macroporous. Interestingly, the high molecular weight of the polystyrene seed had a negligible influence on the change of porosity of the seeded polymerized particles. It is believed that the viscosity of the swollen droplet phase remained pretty high with the change in composition because the polystyrene seed copolymerized with urethane cacrylate had many side chains. Received: 16 December 1999 Accepted: 9 August 2000     

Interpolymer Complexes of Poly(N,N-Dimethylacrylamide/Poly(Styrene-co-Acrylic Acid): Thermal Stability and FTIR Analysis

Summary: This contribution will focus on the elaboration and characterizations of new materials with optimal properties as interpolymer complexes, upon mixing poly (styrene-co-acrylic acid containing 18, 27 and 32 mol % of acrylic acid (SAA-x) and poly (N,N-dimethylacrylamide) (PDMA), through the control of the densities, strength, self-association and accessibility of the interacting species. These elaborated interpolymer complexes, of different structures, investigated by DSC and TGA, exhibited a significant improved thermal stability. Their DSC analysis showed that all these materials showed one composition-dependence glass transition temperature Tg, indicating the formation of a single homogeneous phase. The different behaviors of Tg-initial composition observed with these systems were analyzed by the approaches of Kwei and Brostow et al., recently developed. The specific interactions that occurred within the elaborated materials were evidenced qualitatively by ATR/FTIR spectroscopy, from the appearance of new bands in the 1800–1550 cm⁻¹ region.     

A Safety Strategy for Producing Poly(Acrylic Acid) of Low Molar Mass

The synthesis of poly(acrylic acid) (PAA) of low molar mass under safe conditions is difficult due to the high polymerization rate of acrylic acid (AA) and the fast heat generation. The aqueous‐solution “semibatch” polymerization of non‐ionized AA in almost starved conditions involves high initiator loads when low molar masses are required. This article proposes the simultaneous feeding of AA and nonconventional chain transfer agents (CTA) as a strategy aimed at controlling both the molar masses and the generated heat rate. Three CTAs are investigated: 2‐mercaptoethanol, thioglycolic acid, and isopropyl alcohol. Even when PAA of relatively low molar mass can be produced by adequately selecting the flow rates and concentrations of both AA and CTA, it is found that the nature of CTA can have a significant effect on the polymerizations kinetics. The mechanisms responsible for these effects are discussed with the help of a representative mathematical model.

     

聚乳酸组织工程支架结构的精密调控

采用糖球模板法结合热致相分离技术,制备了孔径尺寸、内连通度及孔隙率高度可控的左旋聚乳酸(PLLA)支架材料,并通过扫描电镜(SEM)、红外光谱(FTIR)以及示差扫描量热法(DSC)对其空间结构及性能进行了系统研究.支架材料孔径从50μm到800μm及内连通孔径从10μm到200μm连续可调,微观孔壁结构根据不同溶剂可形成各异的微纳米结构.支架的制备对PLLA化学结构无显著影响,但相分离过程会不同程度地降低PLLA的结晶度.     

聚四氢呋喃三元醇的合成及表征

合成了一种新的三元引发剂[C₂H₅C(CH₂OCH₂CH₂CO+ClO₄^-)₃],并用于制备聚四氢呋喃三元醇.用¹HNMR,FTIR和GPC法对聚合物的结构进行了表征.结果表明,产物中环状齐聚物的含量极低.对聚合物水解产物的分子量及分子量分布测定结果表明,产物为预期的三元醇,聚合反应过程中链转移可以忽略,聚合物的分子量可控.     

聚酰胺酸盐稳定的金纳米催化剂用于羧酸的绿色合成

使用一锅法成功制备了水溶性聚酰胺酸盐稳定的金纳米催化剂(AuNPs-PAAS),将该催化剂用于伯醇的催化氧化.利用紫外-可见分光光度计,X射线衍射仪(XRD),透射电子显微镜(TEM)等表征方法对催化剂进行了表征.结果表明,金纳米粒子在聚酰胺酸溶液中处于均匀分散状态,金纳米尺寸约为5 nm.将制备的纳米金催化剂用于伯醇的氧化,评价了其在伯醇氧化成羧酸反应中的催化性能,结果显示,在空气为氧化剂,水为溶剂的条件下,AuNPs-PAAS对伯醇的催化氧化为高效的准均相催化过程,高选择性得到羧酸产物,通过调节溶液的pH值,可以很容易的实现产物与反应体系分离和催化剂的回收和循环利用.     

Poly(methyl methacrylate)-induced Microstructure and Hydrolysis Behavior Changes of Poly(L-lactic acid)/Carbon Nanotubes Composites

Poly(L-lactic acid)(PLLA)-based composites exhibit wide applications in many fields.However,most of hydrophilic fillers usually accelerate the hydrolytic degradation of PLLA,which is unfavorable for the prolonging of the service life of the articles.In this work,a small quantity of poly(methyl methacrylate)(PMMA)(2 wt%-10 wt%)was incorporated into the PLLA/carbon nanotubes(CNTs)composites.The effects of PMMA content on the dispersion of CNTs as well as the microstructure and hydrolytic degradation behaviors of the composites were systematically investigated.The results showed that PMMA promoted the dispersion of CNTs in the composites.Amorphous PLLA was obtained in all the composites.Largely enhanced hydrolytic degradation resistance was achieved by incorporating PMMA,especially at relatively high PMMA content.Incorporating 10 wt%PMMA led to a dramatic decrease in the hydrolytic degradation rate from 0.19%/h of the PLLA/CNT composite sample to 0.059%/h of the PLLA/PMMA-10/CNT composite sample.The microstructure evolution of the composites was also detected,and the results showed that no crystallization occurred in the PLLA matrix.Further results based on the interfacial tension calculation showed that the enhanced hydrolytic degradation resistance of the PLLA matrix was mainly attributed to the relatively strong interfacial affinity between PMMA and CNTs,which prevented the occurrence of hydrolytic degradation at the interface between PLLA and CNTs.This work provides an alternative method for tailoring the hydrolytic degradation ability of the PLLA-based composites.     

ABA型聚L-丙氨酸-聚乙二醇嵌段共聚物的合成及其表征

利用L-α-丙氨酸和三聚光气反应制备了N-羧基-α-丙氨酸-环内酸酐(NCA).以聚乙二醇(PEG)为原料.制备了端氨基聚乙二醇(PEG-NH₂),并以此作为引发剂,引发NCA开环聚合.合成了不同组成和分子量的聚L-丙氨酸-聚乙二醇(PLAA-PEG-PLAA)嵌段共聚物.利用IR、¹H NMR、DSC、WAXD、CD等方法对共聚物结构进行了表征.结果表明,PEG-NH₂引发NCA开环聚合得到的是嵌段共聚物,通过¹H NMR谱得到共聚物组成及数均分子量;引入PEG的结果使聚L-丙氨酸的亲水性有所改善;CD测诚结果表明共聚物在水溶液中主链主要以α-螺旋构象存在.     

聚L-谷氨酸可注射水凝胶的制备及性能

通过活化改性聚L-谷氨酸（PLGA）制备酰肼化PLGA（PLGA-ADH）和3-氨基-1,2-丙二醇改性的PLGA（PLGA-OH）,PLGA-OH经高碘酸钠氧化制得醛基化PLGA（PLGA-CHO）,以PLGA-ADH和PLGA-CHO为前驱体,通过席夫碱交联反应构建了PLGA可注射水凝胶.研究了酰肼化和醛基化改性前后PLGA的结构变化,考察了固含量对水凝胶成胶时间、溶胀行为、机械性能、体外降解性能、药物释放行为及微观形貌等的影响,并进行了初步的细胞培养实验及裸鼠皮下注射成胶实验.结果表明,该PLGA可注射水凝胶在组织工程领域具有良好的应用前景.     

苯胺链段为侧基的聚酰胺酸的合成及性质

采用三元共聚法制备了苯胺齐聚物为侧链的接枝型聚酰胺酸. 通过红外光谱、核磁共振谱及高效凝胶渗透色谱等技术对聚合物结构进行了表征. 该材料亚胺化后具有十分优异的热稳定性. 紫外-可见光谱和电化学测试结果表明, 该聚合物具有独特的光谱性质和可逆的电化学活性. 聚酰胺酸/ITO电致变色电极具有颜色变化明显, 响应速度较快, 着色效率高等优点, 是一种综合性能较好的电致变色聚合物材料.     

Synthesis and Properties of Poly(N-isopropylacrylamide-co-acrylamide) Hydrogels

Poly (N-isopropylacrylamide-co-acrylamide) [Poly(NIPAAm-co-AAm)] with different feed ratios were obtained by radiation polymerization using Co⁶⁰γ-rays. Swelling equilibrium data in various media: deionized water, aqueous NaCl solutions and different pH buffer solutions, were determined. It appeared that the lower critical transition temperature (LCST) of the hydrogels increased with an increasing acrylamide content and decreased with increasing ionic strength. Moreover, LCST was affected by pH.     

胆固醇修饰的低分子量聚乙烯亚胺接枝化聚[L-天冬酰胺-co-L-赖氨酸]作为基因载体的性能研究

通过将低分子量的聚乙烯亚胺(PEI600)及其胆固醇衍生物与聚(L-天冬酰胺-co-L-赖氨酸)(PSL)进行开环反应, 合成了一类新型的肿瘤靶向基因载体, 研究了这类载体与DNA形成复合物的性质以及介导绿色荧光蛋白质粒pEGFP-C1转染不同细胞的性能. 结果表明, 在复合质量比大于5∶1时, 各载体均能与DNA形成结构稳定的复合物. 同时转染实验结果证明, 通过在侧链引入一定数目的胆固醇, 可以明显提高载体对于癌细胞HepG2和Hela的转染效率. 这类新型的载体具有良好的细胞相容性、较高的转染效率以及易于进行靶向修饰等特点, 在基因治疗研究领域中将具有较好的潜在应用价值.     

Electrocatalytic Oxidation of Hydrazine at the Poly(Glutamic Acid) Chemically Modified Electrode and Its Amperometric Determination

ABSTRACT

The electrochemical polymerization of glutamic acid at the glassy carbon electrode was investigated in phosphate buffer solution by cyclic voltammetry. The applied voltage range, pH of electrolyte, cyclic number were explored for optimal polymerization conditions. The resulting film exhibits an electrocatalytic ability to hydrazine, reducing the overpotential by 500mV. The electrocatalytic response of hydrazine is evaluated with regard to pH, scan rate, applied voltage, hydrazine concentration and other variables. The rate constant of the catalytic reaction was 1.2 × 10⁴ M^?1.s^?1. When used as amperometric detector, the modified electrode yields a detection limit of 1 × 10^?8 M hydrazine. The electrode is rather stable even after use for a month and a reproducible response was obtained.     

Poly[2-(N,N-Dimethylamino) Ethyl Methacrylate] /Poly(Styrene-Co-Methacrylic Acid) Interpolymer Complexes

Summary: Poly[2-(N,N-dimethylamino)ethyl methacrylate] (PDMAEMA), copolymers of different compositions of styrene with 2-(N,N-dimethylamino)ethyl methacrylate (SDMAEMA) or methacrylic acid (SMA) were synthesized by free radical polymerization and characterized by several techniques. Different ternary mixtures containing proton-acceptors PDMAEMA or SDMAEMA, proton-donor copolymers SMA and a solvent (butan-2-one or THF) were prepared. The present study, that investigated several factors that affected the phase behaviors of the ternary mixtures above, confirmed that, indeed depending on the nature of solvent, densities of interacting species, amounts of efficient specific interactions that occurred between the two copolymers, interpolymer complexes of different structures were elaborated. The complexation phenomena, observed with these different systems were analyzed in solution by viscometry that confirmed these effects in monitoring the formation of interpolymer complexes. The specific interactions that occurred between pairs of polymers of each system above were qualitatively evidenced by FTIR spectroscopy from the appearance of new bands or their new redistribution. The glass transition temperature Tg of the obtained complexes of different structures determined by DSC varied differently with the weight fraction of one of the copolymers. These various Tg-compositions were analyzed using the Kwei and Brostow et al. approach recently developed. Thermal analysis of some of the elaborated complexes, examined by thermogravimetry, confirmed their improved thermal stability.     

Synthesis and Characterization of Modified Polyimides: Poly(Urethane-Imide)

Abstract

Poly(urethane-imide)s (PUIs) were prepared by the Diels–Alder (DA) reaction of 5-(2-furanylmethylcarbamato)-1-[1-(2-furanylmethylcarbamatomethyl)]-1, 3, 3, -trimethylcyclohexane (FFCH) with various bismaleimides. The DA reaction was carried out in 1, 4-dioxane as the solvent as well as in bulk. This was followed by aromatization of the polytetrahydrophthalimide intermediate in the presence of acetic anhydride. All polymers were characterized by elemental analysis, IR spectral studies, and thermogravimetry. The PUIs exhibited moderate thermal stability. FFCH and bismaleimide were polymerized (at 145 ± 10°C) by an in-situ DA reaction into thermally stable PUIs-glass fiber composites (i.e., laminates) and were characterized by their chemical resistance and mechanical properties.