三聚氰胺氰尿酸盐对玻纤增强尼龙66复合材料阻燃性能的影响

将三聚氰胺氰尿酸盐(MCA)阻燃剂添加到玻纤增强的尼龙66复合材料(GF-PA66)中。利用UL-94实验对MCA在复合材料中的阻燃效果进行研究;通过扫描电子显微镜(SEM)分析了燃烧后的样品形貌,并利用热重分析法对复合材料的热分解行为进行了研究。结果表明:MCA可使玻纤增强尼龙66复合材料达到UL-94V-0级阻燃效果;MCA晶体被均匀地分散于尼龙基体中,在燃烧时MCA通过自身吸热分解,产生不可燃气体,实现气相阻隔,从而起到阻燃作用,并在复合材料自熄面上留下纳米级气孔。     

尼龙6/蒙脱土纳米复合材料非等温结晶动力学和透明性研究

将有机化的蒙脱土与尼龙6(PA6)在Haake共混机中共混,制备出尼龙6/蒙脱土纳米复合材料(PA6N);对尼龙6/蒙脱土纳米复合材料和纯尼龙6分别进行差示扫描量热法非等温结晶试验,以了解蒙脱土在尼龙6/蒙脱土纳米复合材料中的成核作用、扩大尼龙6在包装领域的应用范围.与此同时,采用偏光显微镜测定了样品的结晶形态;采用紫...     

尼龙6/石墨纳米导电复合材料的制备与性能

通过原位插层聚合制备了尼龙 6 /石墨纳米导电复合材料 ,其室温导电渗滤阈值为 =0 75vol% ,远远低于常规导电粒子填充的聚合物复合材料 .当石墨体积分数为 2 0vol%时 ,室温电导率可达 10 -4 S/cm .透射电镜研究表明 :由于石墨经高温膨胀后其片层被剥离导致了片状石墨粒子具有巨大的径厚比 ,经原位插层聚合其片层厚度进一步被剥离为几十个纳米 ,同时原位插层聚合使得石墨粒子能够均匀分散在尼龙 6基体中 ,因而导致了该导电复合材料的低渗滤阈值和高导电性能 .     

尼龙6/抗菌蛭石复合材料的制备及性能研究

通过离子交换法对蛭石进行载银和有机化改性,制备出3种抗菌蛭石,进一步采用熔融共混法制备了尼龙6/抗菌蛭石复合材料,测试了复合材料的抗菌性能和物理力学性能,利用TEM和SEM观察了蛭石在尼龙6中的分散情况和拉伸断面.研究结果表明,载银并有机化的蛭石与尼龙6的复合材料对大肠杆菌和金黄色葡萄球菌均具有明显的抑菌圈,对大肠杆菌...     

MC尼龙-纳米La2O3复合材料的制备及性能研究

用原位分散聚合法制备了一系列MC尼龙／纳米La2O3复合材料，研究了纳米La2O3用量对复合材料力学性能的影响，用SEM观察了La2O3粒子在MC尼龙基体中的分散情况，用XRD对复合材料的晶体结构进行了表征。SEM观察结果表明，当纳米La2O3用量小于1％时，纳米La2O3均匀分散于MC尼龙基体中，团聚情况很少，当纳米La2O3用量大于1％时，纳米La2O3开始团聚；XRD研究结果表明，纳米La2O3没有改变MC尼龙的结晶形态；力学性能的研究结果表明，随着纳米La2O3用量的增加，复合材料的拉伸强度、断裂伸长率、缺口冲击强度、弯曲强度和弯曲模量都呈先升后降的趋势，当纳米La2O3用量为0．5％时，复合材料的拉伸强度和断裂伸长率达到最大值，分别比MC尼龙提高17．9％和52．1％，当纳米La2O3的用量为1．0％时，复合材料的缺口冲击强度、弯曲强度和弯曲模量达到最大值，分别比MC尼龙基体提高36，6％．12．7％和16．3％。     

原位缩聚法制备碳纳米管/尼龙11复合材料

用原位缩聚法制备了碳纳米管增强的尼龙11复合材料,用X射线衍射仪、红外(FTIR)、扫描电镜(SEM)、热重(TGA)、机械拉伸测试仪等对其结构、形貌、热性能及机械性能进行了表征测试.扫描电镜结果显示碳纳米管均一地分散在尼龙11/碳纳米管复合材料中.复合材料的拉伸模量比纯尼龙11有较大的提高.当复合材料中碳纳米管含量分别为1%,5%,10%时,材料的拉伸模量分别提高了34.5%,92.9%和113,7%.同时,复合材料的储能模量也有提高.热分析结果显示当复合材料中碳纳米管含量为1%时,其失重5%和10%的温度分别由纯尼龙11的404℃、424℃提高到414℃和437℃.示差扫描量热分析(DSC)显示复合材料的结晶温度随碳纳米管的加入而升高,而结晶度则降低.     

铸型尼龙/纳米ZnO复合材料的制备与表征

采用原位聚合反应制备MC尼龙6/纳米ZnO复合材料并对其性能、形貌和结晶形态进行了分析.分析结果表明:MC尼龙6/纳米ZnO复合材料中ZnO达到了纳米级分散,并且粒子分布比较均匀,粒子的粒径在30~50 nm左右.纳米ZnO没有改变尼龙6的结晶形态.纳米ZnO的加入起到同时增强增韧的作用;使体积电阻系数降了8×104倍、表面电阻系数降了5.7×104倍、摩擦系数降低了29%,MC尼龙6/纳米ZnO复合材料摩擦磨损性能和抗静电性能明显优于MC尼龙6;经过力学拉伸试验的破坏,引起MC尼龙6结构发生宏观应力变化,造成(002 202晶面)产生明显的择优取向.     

kevlar纤维增强尼龙6复合材料的力学性能

对Kevlar纤维进行了改性,使其成为己内酰胺阴离子开环聚合的活性中心,采用阴离子接枝法在Kevlar纤维(KF)表面接枝尼龙6低聚物,并与基体尼龙6混合,用挤出和注塑方式制备了尼龙6/改性Kevlar纤维(PA6/KF1)复合材料。ESEM和XPS分析表明,Kevlar纤维表面接枝上了尼龙6低聚物。比较了尼龙6/未改性Kevlar纤维(PA6/KF0)和PA6/KF1复合材料的力学性能及破坏形态,同时探讨了其破坏机理。结果表明,接枝尼龙6的KF1增强了KF与尼龙6复合材料界面的相互作用,拉伸强度、弯曲强度和弯曲模量分别提高了20.69%、12.26%和14.23%,但冲击强度降低了8.2%;当复合材料被破坏时,未改性纤维表面只粘附有少量的树脂尼龙6,而改性纤维的表面有较多的树脂包覆层,呈部分非界面脱粘破坏,具有良好的界面结合能力。     

尼龙6/SiO_2纳米复合材料的制备及其力学性能和热稳定性

以表面含有氨基的可反应性纳米SiO2(RNS-A)和表面含有烷基碳链的可分散性纳米SiO2(DNS-3)作为填料,利用原位聚合法制备了尼龙6/SiO2纳米复合材料(相应的复合材料分别简记为RPA和DP3);采用透射电子显微镜观察了复合材料中纳米SiO2的表面形貌,并利用热失重分析仪测定了复合材料的热稳定性,进而考察了纳米SiO2表面功能基团对尼龙6力学性能和热稳定性的影响.结果显示,纳米SiO2能够很好地分散在尼龙6基体中,并使尼龙6的热分解温度提高10℃左右.与此同时,RPA的最大拉伸强度和冲击强度较纯尼龙6的分别提高34.5%和12.5%,DP3的最大拉伸强度和冲击强度分别提高18.2%和45.7%.这表明两种纳米SiO2均可以有效地提高尼龙6的力学性能和热稳定性;可以推测,纳米SiO2的增强效应与其在尼龙6基体材料中的分散和界面作用有关.     

尼龙纳米复合材料研究进展

综述了尼龙纳米复合材料的制备方法、性能特点以及近几年来国内外对尼龙纳米复合材料产品开发进展情况。重点从纳米粒子对复合材料结晶行为的影响以及纳米粒子与尼龙界面相互作用两方面研究纳米粒子增强增韧尼龙的机理。并展望了尼龙纳米复合材料的应用前景。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.