电极条件对硫酸介质中电解还原提纯镱过程的影响

研究了以钌铱钛合金网和汞分别为阳、阴电极, 在无气氛保护条件下, 采用电解还原方法从铥、镱、镥硫酸盐溶液中分离提纯镱的过程. 讨论了在8 V恒电压时的电极间距、位置, 以及阴、阳极表面积对电解过程中的电流、还原率影响. 优化了电解还原过程, YbSO4产品的纯度稳定达到99.5%以上, 一次收率可达80%;提镱后母液中的铥和镥被富集4倍以上, 其中Lu含量高于50%, 十分有利于后续铥/镥分离.     

Cyanex272-P507浸渍树脂协同萃取色层分离铥镱镥的研究

以Cyanex272-P507浸渍树脂采用萃取色层法对铥镱镥富集物进行了吸附和淋洗分离研究,考察了淋洗剂浓度、稀土负载量、淋洗液流速等因素对分离铥镱镥富集物的影响。结果表明,在充填的树脂粒度为0.3~0.6 mm的色层柱中,以0.2 ml.cm-2.min-1进料流速时能得到较大的吸附率;在稀土负载量为树脂重量的0.6%,淋洗液流速为1.0 ml.cm-2.min-1,温度为30℃,装柱树脂高度为400 mm(高径比为25∶1)的条件下,用1.0,1.5,2.0 mol.L-1盐酸梯度淋洗Tm,Yb,Lu,可实现铥镱镥富集物三者的完全分离。     

钨酸盐/过钨酸盐体系阴极间接电氧化合成红曲黄色素

以自制SBS-g-(AA/StSO3Na)/SBS-g-DMAEMA双极膜作电解槽阴阳两极室的隔膜,借助正交试验确定阴极电还原氧气产生过氧化氢的最优条件,进而利用钨酸钠/过钨酸钠体系由阴极间接电氧化红曲红制备红曲黄色素.实验表明:以石墨作电极,阳极液为10%硫酸溶液,阴极液为0.5g·L-1红曲红丙酮水溶液,添加钨酸钠(浓度15mmol/L),调节pH至3,在通氧速率65cm3/min,电流密度5.78mA.cm-2下电解2h,阴极平均电流效率可达72.39%.电解产物经红外表征和紫外跟踪分析,证实了红曲红烯键环氧化反应的发生.     

V(Ⅲ)-V(Ⅳ)电解液的电解合成

以硫酸氧钒(VOSO4)为原料,电解合成了用于制备钒电池的混合价态钒离子[V(Ⅲ)-V(Ⅳ)]电解液.较适宜的电化学反应条件为:以Ir-Ta/Ti为阳极,导电石墨板为阴极;4 mol·L-1 H2SO4为阳极电解液,2 mol·L-1 VOSO4-2 mol·L-1H2SO4混合溶液为阴极电解液,于1A电解6 h.在此条件下进行电化学反应,电解液的电化学活性高,电导率稳定;电解过程实现了较高的电流效率(接近100%)和较低的电能损耗(345 Wh·kg-1).     

固定床反应器电合成乙醛酸的研究

以过饱和草酸水溶液为阴极液 ,盐酸为阳极液 ,在固定床电解槽中草酸电还原得到乙醛酸 .考察改变固定床的结构、电解温度及电流密度对生成乙醛酸电流效率和产率的影响 .结果表明 ,以铅粒作阴极 ,石墨板作阳极 ,电流密度 96 .3A·m- 2 ,阴极液空速 0 .5 0 5m·s- 1,电解温度 32℃时 ,在固定床双阳极室内反应 4 5min ,乙醛酸的电流效率仍达到 6 6 .2 % ,浓度 2 .0 2 %     

荧光级铈铽共晶氧化物合成工艺的研究

采用氯化铈铽水溶液与草酸为原料, 合成了铈铽共晶氧化物. 稀土收率≥99%. 研究了料液浓度、酸度、温度、草酸浓度、铈铽配分改变对稀土收率的影响.     

重稀土硫酸盐体系电解还原提纯镱的研究

采用电解还原方法，以钌-铱-钛合金网和汞为阳、阴极，在无气氛保护的条件下，实现了从重稀土(Tm，Yb，Lu)富集物的硫酸盐溶液中选择性地还原和提取镱。在获得稀土纯度达99．5％的YbSO4的同时，剩余物中的铥、镥也被富集了约3倍。研究中还对不同阳极和阴极材料的性能进行了比较和筛选，考察了体系的还原效率，以及电流、电压的时间响应过程。     

Ti/nanoTiO_2-Pt阳极和Ti/nanoTiO_2阴极成对电合成葡萄糖酸锌和丁二酸

使用新颖的纳米结构电极成对电合成葡萄糖酸锌和丁二酸.采用溶胶-凝胶法制备Ti基纳米TiO2(Ti/nanoTiO2)电极,同时采用电沉积法制备Ti基纳米TiO2-Pt(Ti/nanoTiO2-Pt)修饰电极.通过循环伏安研究发现,Ti/nanoTiO2-Pt电极对葡萄糖氧化及Ti/nanoTiO2电极对马来酸还原均具有高催化活性.以Ti/nanoTiO2-Pt电极为阳极、Ti/nanoTiO2电极为阴极,通过正交实验得到成对电合成葡萄糖酸锌和丁二酸的优化条件为:阳极和阴极电流密度分别为1.2A·dm-2和3.0A·dm-2,阳极液为0.4mol·L-1葡萄糖+0.6mol·L-1NaBr,阴极液为0.6mol·L-1马来酸+0.2mol·L-1NaCl,温度50℃.成对电合成的总电流效率达到170%.     

间接电氧化2-丁酮制备α-羟基缩酮的研究

在板框式循环电解槽中,以KOH为电解质,KI为催化剂,石墨电极分别为阳极和阴极,研究电化学间接氧化2-丁酮合成乙偶姻中间体α-羟基缩酮,讨论电流密度、极板间电解液流速、电解液中2-丁酮浓度、电解温度以及通电量等电解条件对中间体收率和电流效率的影响,经优选工艺条件为：电流密度40 mA·cm^-2,流速6.4 cm·s^-1,2-丁酮浓度1.75 mol·L^-1,电解温度30℃,通电量为1.5 F·moL^-1时,中间体收率可达78.9%,电流效率40.1%. 循环伏安测试结果表明,电解时碘离子在阳极氧化生成碘单质,甲醇在阴极还原生成甲氧基负离子,原料2-丁酮与电解产物反应,并最终生成乙偶姻中间体.     

阴极冷却反应器电合成乙醛酸

以过饱和草酸水深液为阴极液 ,盐酸溶液为阳极液 ,在阴极冷却电化学反应器内草酸电解合成乙醛酸 .考察了电极温度、电解液温度、电流密度和电极材料对合成乙醛酸的时空产率和电流效率的影响 .结果表明 ,阴极冷却反应器既节省能耗 ,又可使电解过程在较高草酸浓度下进行 ,提高电流效率和时空产率 .用石墨板做阳极 ,铅做阴极 ,电流密度为 4 0 9.4 6A·m-2 ,阴极液流速 μ=1 .0 8m·s-1,电解温度为 2 0℃左右时 ,电解 3 .70h ,可得到质量分数为 3 .52 %的乙醛酸溶液 ,平均时空产率为 0 .0 3 2kg·dm-3·h     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.