Correlating interface heterostructure, charge recombination, and device efficiency of poly(3-hexyl thiophene)/TiO2 nanorod solar cell

The charge recombination rate in poly(3-hexyl thiophene)/TiO(2) nanorod solar cells is demonstrated to correlate to the morphology of the bulk heterojunction (BHJ) and the interfacial properties between poly(3-hexyl thiophene) (P3HT) and TiO(2). The recombination resistance is obtained in P3HT/TiO(2) nanorod devices by impedance spectroscopy. Surface morphology and phase separation of the bulk heterojunction are characterized by atomic force microscopy (AFM). The surface charge of bulk heterojunction is investigated by Kelvin probe force microscopy (KPFM). Lower charge recombination rate and lifetime have been observed for the charge carriers in appropriate heterostructures of hybrid P3HT/TiO(2) nanorod processed via high boiling point solvent and made of high molecular weight P3HT. Additionally, through surface modification on TiO(2) nan,orod, decreased recombination rate and longer charge carrier lifetime are obtained owing to creation of a barrier between the donor phases (P3HT) and the acceptor phases (TiO(2)). The effect of the film morphology of hybrid and interfacial properties on charge carrier recombination finally leads to different outcome of photovoltaic I-V characteristics. The BHJ fabricated from dye-modified TiO(2) blended with P3HT exhibits 2.6 times increase in power conversion efficiency due to the decrease of recombination rate by almost 2 orders of magnitude as compared with the BHJ made with unmodified TiO(2). In addition, the interface heterostructure, charge lifetime, and device efficiency of P3HT/TiO(2) nanorod solar cells are correlated.     

Understanding of morphology evolution in local aggregates and neighboring regions for organic photovoltaics

Fluorescence intensity and its ratio mapping combined with time-dependent optical microscopy and atomic force microscopy (AFM) were used to understand morphology evolution of local aggregates and neighboring regions for organic solar cells. Three solvents with different boiling points including chlorobenzene (CB), 1,3-dichlorobenzene (1,3-DCB) and 1,2-dichlorobenzene (1,2-DCB) were used to engineer morphology. These solvents affected morphology evolution factors such as solvent evaporation rate, formation (e.g., growth rate, size and/or quantity) of (6,6)-phenyl-C61-butric-acid methyl ester (PCBM)-rich aggregates, and packing/ordering of poly(3-hexylthiophene) (P3HT). Three local regions (1, 2 and 3) including microscale aggregates and their surrounding areas were identified to explore the mechanism of morphology evolution. Region 1 was the PCBM-rich aggregates; region 2 was the PCBM-deficient area; and region 3 was the area composed of a relatively normal P3HT/PCBM composite beyond region 2 for each solvent. The intensity of fluorescence spectra decreased as region 1 > region 2 > region 3 in thermally annealed (140 °C, 20 min) P3HT/PCBM blend film from each solvent. The highest fluorescence intensity in region 1 was probably caused by the relatively poor phase separation where both PCBM and P3HT formed large isolated domains. The higher fluorescence intensity ratio (720 nm/650 nm) suggested a larger relative amount of PCBM molecules, supported by similar morphologies in fluorescence intensity ratio mapping compared to those in optical images. The fluorescence intensity ratio was with the order of region 1 > region 3 > region 2 in both CB and 1,3-DCB based films, but with region 1 > region 2 > region 3 for the 1,2-DCB based film. The order of effective area taken up by aggregates was CB > 1,3-DCB > 1,2-DCB in annealed (140 °C, 10 min) bulk blend films. The final solar cell performance agreed with morphology results. This work is imperative with regards to revealing the mechanism of morphology evolution in local aggregates and surrounding regions for organic photovoltaic films.     

Oriented poly(3-hexylthiophene) nanofibril with the π-π stacking growth direction by solvent directional evaporation

In this article, the uniaxial alignment of poly(3-hexylthiophene) (P3HT) nanofibrils with a π-π stacking growth direction in which P3HT chains adopt a flat-on conformation was obtained by solvent directional evaporation using a glass cover slide and a poly(dimethylsiloxane) (PDMS) sheet to press the P3HT film in a carbon disulfide (CS(2)) atmosphere. By controlling the CS(2) vapor pressure during the film-forming process, we got a well-oriented P3HT film whose order parameter reached as high as 0.97. The orientation of the film was induced by the crystallization nucleation of P3HT and the directional evaporation of the solvent. Under a CS(2) vapor atmosphere, P3HT crystals preferred to adopt the form II modification, which started by nucleation. Owing to the solvent directional evaporation from the center to the margin, P3HT at the center of the sample would precipitate first to induce nucleation. Then the peripheral P3HT would directly diffuse, precipitate, and then adhere to the nucleus to form the uniaxial alignment of P3HT nanofibrils along the direction of solvent evaporation. Furthermore, in the P3HT nanofibrils, the π-π stacking direction of P3HT lamellae was parallel to the crystal growth direction, which would provide an effective path for charge transport.     

Interplay of three-dimensional morphologies and photocarrier dynamics of polymer/TiO2 bulk heterojunction solar cells

In this study, we investigated the interplay of three-dimensional morphologies and the photocarrier dynamics of polymer/inorganic nanocrystal hybrid photoactive layers consisting of TiO(2) nanoparticles and nanorods. Electron tomography based on scanning transmission electron microscopy using high-angle annular dark-field imaging was performed to analyze the morphological organization of TiO(2) nanocrystals in poly(3-hexylthiophene) (P3HT) in optimal solar cell devices. The Three-dimensional (3D) morphologies of these hybrid films were correlated with the photocarrier dynamics of charge separation, transport, and recombination, which were comprehensively probed by various transient techniques. Visualization of these 3D bulk heterojunction morphologies clearly reveals that elongated and anisotropic TiO(2) nanorods in P3HT not only can significantly reduce the probability of the interparticle hopping transport of electrons by providing better connectivity with respect to the TiO(2) nanoparticles, but also tend to form a large-scale donor-acceptor phase-separated morphology, which was found to enhance hole transport. The results support the establishment of a favorable morphology for polymer/inorganic hybrid solar cells due to the presence of the dimensionality of TiO(2) nanocrystals as a result of more effective mobile carrier generation and more efficient and balanced transport of carriers.     

Structure of friction-transferred highly oriented poly(3-hexylthiophene) thin films

Oriented thin films of P3HT were obtained by a friction-transfer technique. The morphology and structure of the film were studied by means of optical microscopy, atomic force microscopy and transmission electron microscopy. Optical microscopy observation indicates that large size well-ordered P3HT thin films can be produced by a friction-transfer technique. Highly ordered lamellae were observed in P3HT friction-transferred films by electron microscopy. Electron diffraction results confirm the existence of high orientation with the a- and c-axes of P3HT crystals aligned in the film plane while the c-axis parallel to the friction-transfer direction. The atomic force microscopy observation of the as-prepared P3HT thin film shows, however, a featureless top surface morphology, indicating the structure inhomogeneity of the obtained film. To get highly oriented P3HT thin films with homogenous structure, high temperature annealing, solvent vapor annealing and self-seeding recrystallization of the friction-transferred film were performed. It is confirmed that solvent vapor annealing and self-seeding recrystallization methods are efficient in improving the surface morphology and structure of the frictiontransferred P3HT thin film. Highly oriented P3HT films with unique structure can be obtained through friction-transfer with subsequent solvent vapor annealing and self-seeding recrystallization.     

CONTROLLING THE 3D NANOSCALE ORGANIZATION OF BULK HETEROJUNCTION POLYMER SOLAR CELLS

In this study,the three dimensional nanoscale organization in the photoactive layers of poly(3-hexylthiophene) (P3HT) and a methanofullerene derivative (PCBM) is revealed by transmission electron tomography.After annealing treatment,either at elevated temperature or during slow solvent evaporation,nanoscale interpenetrating networks are formed with high crystalline order and favorable concentration gradients of both components through the thickness of the photoactive layer.Such a tailored morphology acco...     

CONTROLLING THE 3D NANOSCALE ORGANIZATION OF BULK HETEROJUNCTION POLYMER SOLAR CELLS

  In this study, the three dimensional nanoscale organization in the photoactive layers of poly(3-hexylthiophene) (P3HT) and a methanofullerene derivative (PCBM) is revealed by transmission electron tomography. After annealing treatment, either at elevated temperature or during slow solvent evaporation, nanoscale interpenetrating networks are formed with high crystalline order and favorable concentration gradients of both components through the thickness of the photoactive layer. Such a tailored morphology accounts for the considerable increase of the power conversion efficiency in corresponding solar cell devices.     

给受体共混质量比对P3HT:PCBM薄膜结构和器件性能的影响

以聚3-己基噻吩(P3HT)为给体、[6,6]-苯基-C61-丁酸甲酯(PCBM)为受体的光伏体系作为研究对象,采用溶剂退火的后处理方法制备薄膜样品,利用紫外-可见(UV-Vis)吸收光谱、原子力显微镜(AFM)、X射线衍射(XRD)等测试手段分别对共混膜样品的形貌和结构进行表征,同时利用熵值统计方法对AFM形貌图像进行分析处理.并在此基础上制备太阳能电池器件,其结构为氧化铟锡导电玻璃/聚3,4-乙撑二氧噻吩:聚苯乙烯磺酸盐/聚3-己基噻吩:[6,6]-苯基-C61-丁酸甲酯/金属铝(ITO/PEDOT:PSS/P3HT:PCBM/Al),研究了给受体共混比例(质量比)对活性层薄膜以及电池性能的影响.结果表明,受体PCBM含量的增加会影响P3HT给体相的有序结晶,当给受体比例为1:1时,活性层薄膜具有较宽的紫外-可见吸收特征,且具有较好的相分离和结晶度,基于该样品制备的电池器件其光电转换效率达到三种比例的最大值(2.77%).表明退火条件下,改变给受体比例可以影响活性层的微纳米结构而最终影响电池的光电转换效率.     

Uniaxial alignment of poly(3-hexylthiophene) nanofibers by zone-casting approach

The preparation of large area coverage of films with uniaxially aligned poly(3-hexylthiophene)(P3HT) nanofibers by using zone-casting approach is reported.The length and the orientation of the nanofibers are defined by the solubility of the solvent,the P3HT molecular weight and the substrate temperature.The length of the oriented nanofibers could be increased from 1 μm to more than 10 μm by adding poor solvent into the P3HT solution.It is found that for P3HT of relatively low molecular weight,a solvent with relatively low solubility has to be chosen to get the oriented film.While for the high molecular weight P3HT,the solvent with a relatively high solubility has to be used.The well-aligned film could be obtained because of the solute concentration gradient in the region where the critical concentration is reached during the zone-casting process.Particularly,the solvent evaporation rate and crystallization rate must be chosen properly to satisfy the stationary conditions above,which were controlled by an appropriate choice of solvent and substrate temperature.The film prepared by zone-casting approach had microcrystalline P3HT domains with more inter-chain order than spin-coating film.Meanwhile,the P3HT π-π stacking direction was parallel to the alignment direction of the nanofibers.     

Vertical phase separation of conjugated polymer and fullerene bulk heterojunction films induced by high pressure carbon dioxide treatment at ambient temperature

The morphology of bulk-heterojunctions (BHJ) is critically important for conjugated polymer and fullerene blend solar cells. To alter the morphology, high pressure (gas phase) carbon dioxide (CO(2)) treatment is applied to poly(3-hexyl thiophene) (P3HT) and [6,6]-phenyl-C61 butyric acid methyl ester (PCBM) blend films under ambient temperature. This process can achieve vertically phase separated morphology such that PCBM distributes toward the film surface, which is suggested by secondary ion mass spectroscopy (SIMS), contact angle, X-ray photoelectron spectroscopy (XPS) and cross-sectional scanning electron microscope (SEM) studies. While pristine P3HT films do not show a significant change upon CO(2) treatment, pristine PCBM films are plasticized in high pressure CO(2). Thus, PCBM is selectively plasticized by CO(2) in the blend film and is drawn towards the surface due to depressed surface energy, although P3HT tends to distribute around the surface without CO(2). This stratification process can enhance solar cell performance. 55% improvement is achieved in the power conversion efficiency of the CO(2) treated device compared to the untreated one, indicating that CO(2) treatment can be a good candidate for optimizing the morphology and enhancing the performance of BHJ polymer solar cells.     

Macroscopic alignment of poly(3-hexylthiophene) for enhanced long-range collection of photogenerated carriers

An epitaxy-directing solvent additive 1,3,5-trichlorobenzene is combined with an off-center spin-casting technique to produce poly(3-hexylthiophene) (P3HT) fibers with uniaxial in-plane alignment on the centimeter scale. Photoconductive atomic force microscopy (pc-AFM) is used to characterize planar heterojunction devices assembled from phenyl-C₆₁ butyric acid methyl ester (PCBM) acceptor and both aligned and unaligned P3HT donor. By varying the relative positions of the laser spot (site of carrier generation) and probe (site of hole extraction), it is found that devices with aligned P3HT exhibit anisotropic and greatly enhanced long-range photocarrier transport, with nearly 10% of original photocurrent measured 400 µm from the laser spot along the direction parallel to the alignment. Complementary thin film transistor (TFT) measurements reveal a factor of ∼3.5 difference in the hole mobilities parallel and perpendicular to the direction of alignment. Together, these findings highlight the importance of macroscopic alignment as a strategy to overcome the low mobilities of disordered polymer semiconductors.1 © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 180–188     

The Effect of Substrate on the Properties of Non-volatile Ferroelectric P(VDF-TrFE)/P3HT Memory Devices

Ferroelectric poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE))/semiconducting poly(3-hexyl thiophene) (P3HT) blend systems have drawn great attention with their potential use for electronic applications, particularly non-volatile memory devices. It is essential to grasp a full understanding of the crystallization habits of the two polymers on different substrates for purposeful control of the structures of the blend and therefore the properties of the devices. Here, the effects of structure and morphology of the blend films generated at different substrate surfaces on the ferroelectric and switching properties of related devices are reported. It is identified that P(VDF-TrFE)/P3HT blend films prepared on graphene substrate show not only an obvious optimization in the ferroelectric behavior of P(VDF-TrFE), but also an enhancement of the charge transport within P3HT domains. By employing sandwich structure constructed by silver electrode and P3HT/P(VDF-TrFE) blend film on graphene substrate, high-performance ferroelectric memory devices have been obtained, which exhibit a great electrical switching behavior with high ON/OFF ratio of about 1000 and low coercive voltage of approximately 5 V. These findings provide useful guidance for fabricating high-performance ferroelectric memory devices.

     

Electronic Properties-Morphology Correlation of a Rod-Rod Semiconducting Liquid Crystalline Block Copolymer Containing Poly(3-hexylthiophene)

The influence of the solvent and annealing temperature on the field-effect mobilities and morphologies of poly(3-hexylthiophene)-b-poly(γ-benzyl-l-glutamate) (P3HT-b-PBLG) rod-rod diblock copolymer has been investigated. Thin film X-ray diffraction studies show peaks originating from both P3HT and PBLG indicating that the crystalline nature of both the blocks is conserved after the formation of the block copolymer. It has been observed that the field-effect mobilities of the diblock copolymer are independent of the annealing temperatures for thin films deposited from both 1,2,4-trichlorobenzene and chloroform solvents. The correlation between the field-effect mobility and morphology indicates that the P3HT block self-assembles at the surface SiO(2) dielectric.     

Influence of single-walled carbon nanotubes induced crystallinity enhancement and morphology change on polymer photovoltaic devices

Single-walled carbon nanotubes (SWNTs) were determined to have significant interaction with poly(3-hexylthiophene) (P3HT), which is helpful to form continuous active film with interpenetrating structure and improve the crystallinity of the resultant film for SWNTs/P3HT composite. Photovoltaic devices based on an active film with relatively higher crystallinity display much enhanced performance. The work function of carbon nanotubes modulated by electron transferring from P3HT to SWNTs is proposed to explain the high open-circuit voltage (V(OC)) obtained from the photovoltaic devices based on the SWNTs/P3HT system.     

Controlled one-dimensional nanostructures in poly(3-hexylthiophene) thin film for high-performance organic field-effect transistors

With the aim of improving the field-effect mobilities in poly(3-hexylthiophene) (P3HT) thin film transistors, we controlled the nanostructures of P3HT thin film by changing the solvent vapor pressure in a spin-coating chamber during solidification. The transistors with P3HT thin films spin-coated under a high solvent vapor pressure (56.5 KPa), showing the one-dimensional nanowire morphologies, resulted in the relatively high field-effect mobilities (0.02 cm2/(V.s)) that are typically more than 1 order of magnitude higher than those prepared under ambient conditions, showing the featureless morphologies. This can be attributed to the higher solvent vapor pressure during film formation, providing the solvent is allowed to evaporate slowly and the degree of ordering within the P3HT crystalline domains is dramatically improved.     

Quantitative nanoorganized structural evolution for a high efficiency bulk heterojunction polymer solar cell

We have developed an improved small-angle X-ray scattering (SAXS) model and analysis methodology to quantitatively evaluate the nanostructures of a blend system. This method has been applied to resolve the various structures of self-organized poly(3-hexylthiophene)/C61-butyric acid methyl ester (P3HT/PCBM) thin active layer in a solar cell from the studies of both grazing-incidence small-angle X-ray scattering (GISAXS) and grazing-incidence X-ray diffraction (GIXRD). Tuning the various length scales of PCBM-related structures by a different annealing process can provide a flexible approach and better understanding to enhance the power conversion of the P3HT/PCBM solar cell. The quantitative structural characterization by this method includes (1) the mean size, volume fraction, and size distribution of aggregated PCBM clusters, (2) the specific interface area between PCBM and P3HT, (3) the local cluster agglomeration, and (4) the correlation length of the PCBM molecular network within the P3HT phase. The above terms are correlated well with the device performance. The various structural evolutions and transformations (growth and dissolution) between PCBM and P3HT with the variation of annealing history are demonstrated here. This work established a useful SAXS approach to present insight into the modeling of the morphology of P3HT/PCBM film. In situ GISAXS measurements were also conducted to provide informative details of thermal behavior and temporal evolution of PCBM-related structures during phase separation. The results of this investigation significantly extend the current knowledge of the relationship of bulk heterojunction morphology to device performance.     

Effect of multiple adduct fullerenes on charge generation and transport in photovoltaic blends with poly(3‐hexylthiophene‐2,5‐diyl)

The effect of replacing [6,6]‐phenyl‐C₆₁ butyric acid methyl ester (PCBM) by its multiadduct analogs (bis‐PCBM and tris‐PCBM) in bulk heterojunction organic solar cells with poly(3‐hexylthiophene‐2,5‐diyl) (P3HT) is studied in terms of blend film microstructure, photophysics, electron transport properties, and device performance. Although the power conversion efficiency of the blend with bis‐PCBM is similar to the blend with PCBM, the performance of the devices with tris‐PCBM is considerably lower as a result of small photocurrent. Despite the lower electron affinity of the fullerene multiadducts, μs‐ms transient absorption measurements show that the charge generation efficiency is similar for all three fullerenes. The annealed blend films with multiadducts show a lower degree of fullerene aggregation and lower P3HT crystallinity than the annealed blend films with PCBM. We conclude that the reduction in performance is due largely to poorer electron transport in the blend films from higher adducts, due to the poorer fullerene network formation as well as the slower electron transport within the fullerene phase, confirmed here by field effect transistor measurements. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2010     

Controlled dispersion of polystyrene‐capped Au nanoparticles in P3HT:PC61BM and consequences upon active layer nanostructure

Numerous recent publications detail higher absorption and photovoltaic performance within organic photovoltaic (OPV) devices which are loaded with Au or Ag nanoparticles to leverage the light management properties of the localized surface plasmon resonance (LSPR). This report details the impact upon film morphology and polymer/nanoparticle interactions caused by incorporation of polystyrene‐coated Au nanoparticles (Au/PS) into the P3HT:PC₆₁BM bulk heterojunction film. Nanostructural analysis by transmission electron microscopy and X‐ray scattering reveals tunable Au/PS particle assembly that depends upon the choice of casting solvent, polymer chain length, film drying time, and Au/PS particle loading density. This Au/PS particle assembly has implications on the spectral position of the Au nanoparticle LSPR, which shifts from 535 nm for individually dispersed particles in toluene to 650 nm for particles arranged in large clusters within the P3HT:PC₆₁BM matrix. These results suggest a critical impact from PS/P3HT phase separation, which causes controlled assembly of a separate Au/PS phase in the nanoparticle/OPV composite; controlled Au/PS phase formation provides a blueprint for designing AuNP/OPV hybrid films that impart tunable optical behavior and potentially improve photovoltaic performance. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 709–720     

Effect of polydispersity on the bulk‐heterojunction morphology of P3HT:PCBM solar cells

Bulk heterojunctions (BHJs) based on semiconducting electron–donor polymer and electron–acceptor fullerene have been extensively investigated as potential photoactive layers for organic solar cells (OSCs). In the experimental studies, poly‐(3‐hexyl‐thiophene) (P3HT) polymers are hardly monodisperse as the synthesis of highly monodisperse polymer mixture is a near impossible task to achieve. However, the majority of the computational efforts on P3HT: phenyl‐C61‐butyric acid methyl ester (P3HT:PCBM)‐based OSCs, a monodisperse P3HT is usually considered. Here, results from coarse‐grained molecular dynamics simulations of solvent evaporation and thermal annealing process of the BHJ are shared describing the effect of variability in molecular weight (also known as polydispersity) on the morphology of the active layer. Results affirm that polydispersity is beneficial for charge separation as the interfacial area is observed to increase with higher dispersity. Calculations of percolation and orientation tensors, on the other hand, reveal that a certain polydispersity index ranging between 1.05 and 1.10 should be maintained for optimal charge transport. Most importantly, these results point out that the consideration of polydispersity should be considered in computational studies of polymer‐based OSCs. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 895–903     

Synthesis of all‐conjugated poly(3‐hexylthiophene)‐block‐ poly(3‐(4′‐(3″,7″‐dimethyloctyloxy)‐3′‐pyridinyl)thiophene) and its blend for photovoltaic applications

New all‐conjugated block copolythiophene, poly(3‐hexylthiophene)‐block‐poly(3‐(4′‐(3″,7″‐dimethyloctyloxy)‐3′‐pyridinyl)thiophene) (P3HT‐b‐P3PyT) was successfully prepared by Grignard metathesis polymerization. The supramolecular interaction between [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) and P3PyT was proposed to control the aggregated size of PCBM and long‐term thermal stability of the photovoltaic cell, as evidenced by differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and optical microscopy. The effect of different solvents on the electronic and optoelectronic properties was studied, including chloroform (CL), dichlorobenzene (DCB), and mixed solvent of CL/DCB. The optimized bulk heterojunction solar cell devices using the P3HT‐b‐P3PyT/PCBM blend showed a power conversion efficiency of 2.12%, comparable to that of P3HT/PCBM device despite the fact that former had a lower crystallinity or absorption coefficient. Furthermore, P3HT‐b‐P3PyT could be also used as a surfactant to enhance the long‐term thermal stability of P3HT/PCBM‐based solar cells by limiting the aggregated size of PCBM. This study represents a new supramolecular approach to design all‐conjugated block copolymers for high‐performance photovoltaic devices. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011.