Desorption of dimethylformamide from Zn4O(C8H4O4)3 framework

Both dimethylformamide (DMF) and diethylformamide (DEF) are important solvents for the synthesis of Zn₄O(C₈H₄O₄)₃ framework (MOF-5). It is generally recognized that DMF molecules can be completely displaced by CH₂Cl₂ during the synthesis of MOF-5. Herein, however, it was found that the DMF molecules inside the pores of the MOF-5 framework cannot be displaced by CH₂Cl₂. The desorption of the DMF molecules from the pores, which requires a temperature of 100 °C or above, is the first order with activation energy of 56.38 kJ/mol. In contrast, DEF molecules can be completely displaced by CH₂Cl₂ during the synthesis of MOF-5, because DEF molecules cannot penetrate into the pores of the MOF-5 paste.     

Elucidating surface properties of dry-etched ZnO using H2/CH4 and H2/CH4/Ar plasma

This paper reports a study of reactive ion etching (RIE) of n-ZnO in H₂/CH₄ and H₂/CH₄/Ar gas mixtures. Variables in the experiment were gas flow ratios, radio-frequency (rf) plasma power, and total pressure. Structural and electrical parameters of the etched surfaces and films were determined. Both the highest surface roughness and highest etching rate of ZnO films were obtained with a maximum rf power of 300 W, but at different gas flow ratios and working pressures. These results were expected because increasing the rf power increased the bond-breaking efficiency of ZnO. The highest degree of surface roughness was a result of pure physical etching by H₂ gas without mixed CH₄ gas. The highest etching rate was obtained from physical etching of H₂/Ar species associated with chemical reaction of CH₄ species. Additionally, the H₂/CH₄/Ar plasma treatment drastically decreased the specific contact and sheet resistance of the ZnO films. These results indicated that etching the ZnO film had roughened the surface and reduced its resistivity to ohmic contact, supporting the application of a roughened transparent contact layer (TCL) in light-emitting diodes (LEDs).     

类花状ZnO-CoFe2 O4 复合纳米管束的制备及其电磁波吸收特性

在90 ℃水溶液中采用两步晶体生长法制备出类花状ZnO-CoFe₂O₄复合纳米管束.ZnO纳米管束的管壁厚度大约为60 nm,管的直径大约为350 nm,CoFe₂O₄纳米颗粒连续包覆在ZnO纳米管束的表面,CoFe₂O₄纳米颗粒尺寸小于40 nm, 壳层厚度随着CoFe₂O₄在ZnO-CoFe₂O_{4 关键词： 类花状 2}O₄')" href="#">ZnO-CoFe₂O₄ 纳米管束 微波吸收剂     

Co3O4-ZnO hierarchical nanostructures by electrospinning and hydrothermal methods

A new hierarchical nanostructure that consists of cobalt oxide (Co₃O₄) and zinc oxide (ZnO) was produced by the electrospinning process followed by a hydrothermal technique. First, electrospinning of a colloidal solution that consisted of zinc nanoparticles, cobalt acetate tetrahydrate and poly(vinyl alcohol) was performed to produce polymeric nanofibers embedding solid nanoparticles. Calcination of the obtained electrospun nanofiber mats in air at 600 °C for 1 h, produced Co₃O₄ nanofibers with rough surfaces containing ZnO nanoparticles (i.e., ZnO-doped Co₃O₄ nanofibers). The rough surfaced nanofibers, containing ZnO nanoparticles (ZnNPs), were then exploited as seeds to produce ZnO nanobranches using a specific hydrothermal technique. Scanning electron microscopy (SEM), and transmission electron microscopy (TEM) were employed to characterize the as-spun nanofibers and the calcined product. X-ray powder diffractometery (XRD) analysis was used to study the chemical composition and the crystallographic structure.     

Evolution of Zn based high purity phases under NH3 gas atmosphere and their PL properties

We report here the evolution of zinc based high purity phases with novel morphologies such as Zn₃N₂ hollow structures, ZnO nanowires and nanopowders, as well as metallic Zn layered hexagonal microparticles at progressively increased reaction temperature of 600 °C, 700 °C, 800 °C under NH₃ gas atmosphere using Zn powder precursor and keeping all other experimental parameters unchanged. Growth mechanism for Zn₃N₂ obtained by nitridation, ZnO by oxidation and Zn microparticles via thermal evaporation & condensation process are discussed briefly. The as-synthesized products were characterized by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS) and scanning electron microscopy (SEM). Photoluminescence (PL) studies have revealed very interesting and infrequently observed emission bands at 378 and 661 nm for Zn₃N₂, 359 and 396 nm for ZnO as well as 389 nm for Zn polyhedral microparticles.     

Self-organized ZnAl2O4 nanostructures grown on -sapphire

Self-organized ZnAl₂O₄ nanostructures with the appearance (in SEM) of high aspect ratio horizontal nanowires are grown on uncatalysed c-sapphire by vapour phase transport. The nanostructures grow as three equivalent crystallographic variants on c-sapphire. Raman and cathodoluminescence spectroscopy confirm that the nanostructures are not ZnO and TEM shows that they are the cubic spinel, zinc aluminate, ZnAl₂O₄, formed by the reaction of Zn and O with the sapphire substrate.     

Modification in structural and optical properties of ZnO, CeO2 doped Al2O3-PbO-B2O3 glasses

The structural and optical analysis of glasses is carried out by XRD, FTIR, density and UV visible spectroscopic measurement techniques. XRD results have confirmed the glassy nature of the samples. The FTIR spectral analysis reveals that with the combined presence of ZnO and CeO₂ contents in Al₂O₃-PbO-B₂O₃ glasses, more BO₃ groups are transformed into BO₄. The optical analysis reveals that optical band gap energy decreases more for CeO₂-ZnO-Al₂O₃-PbO-B₂O₃ glasses (from 2.28 to 1.84 eV). The presence of CeO₂ and ZnO in the glass samples causes more compaction of the borate network due to the formation of more BO₄ groups and the presence of ZnO₄ groups, which results an increase in density, refractive index and decrease of molar volume.     

Synthesis of ZnFe2O4 nanomagnets by Fe-ion implantation into ZnO and post-annealing

Fe ions of dose 8 × 10¹⁶ cm^-2 are implanted into a ZnO single crystal at 180 keV. Annealing at 1073 K leads to the formation of zinc ferrite (ZnFe₂O₄), which is verified by synchrotron radiation X-ray diffraction (SR-XRD) and X-ray photoelectron spectroscopy (XPS). The crystallographically oriented ZnFe₂O₄ is formed inside the ZnO with the orientation relationship of ZnFe₂O₄ (111)//ZnO (0001). Superconducting quantum interference device (SQUID) measurements show that the as-implanted and post-annealing samples are both ferromagnetic at 5 K. The synthesized ZnFe₂O₄ is superparamagnetic, with a blocking temperature (T_B = 25 K), indicated by zero field cooling and field cooling (ZFC/FC) measurements.     

溶胶-凝胶制备ZnO-SiO2复合膜的量子效应和上转换发光

采用溶胶-凝胶技术在玻璃衬底上制备了ZnO薄膜和ZnO-SiO₂复合膜.原子力显微镜照片显示ZnO薄膜具有球状纳米晶粒;可见光-紫外透射光谱表明ZnO-SiO₂复合膜在可见光区的透过率大约是85%,透过率从330 nm开始下降,到290 nm附近降为零.由于量子效应,吸收边出现明显的蓝移.在室温下用不同波长的光激发ZnO-SiO₂复合膜,光致发光谱显示ZnO-SiO₂复合膜对应于激子发射的290 nm附近的紫外发光峰与透射谱所显示的吸收边位置一致,没有出现斯托克斯红移.同时,ZnO-SiO₂复合膜出现了双光子和三光子吸收现象和上转换发光现象. 关键词： 2')" href="#">ZnO-SiO₂ 量子效应 双光子和三光子吸收 上转换发光     

Synthesis of ZnFe2O4 nanocrystallites by mechanochemical reaction

Mechanochemical reaction of ZnO and α-Fe₂O₃ in a planetary mill formed an amorphous precursor, which was subsequently heated to successfully produce zinc ferrite (ZnFe₂O₄) nanocrystallites. The amorphous precursor and nanocrystallites were characterized by differential thermal analysis (DTA), thermogravimetric analysis (TGA), X-ray diffraction (XRD) and transmission electron microscopy (TEM). Calcination of the precursor powder at 600 °C led to the formation of ZnFe₂O₄ nanocrystallites of about 22 nm in crystal size, and most of particle was about 10-50 nm in diameter. Effect of calcination temperature on the crystal size of the nanoparticles was investigated. The mechanism of nanocrystallite growth was primarily investigated. The activation energy of ZnFe₂O₄ nanocrystallite formation during thermal treatment was calculated to be 18.5 kJ/mol.     

Synthesis, structural, magnetic and optical properties of nanocrystalline ZnFe2O4

Nanocrystalline zinc ferrite (ZnFe₂O₄) is synthesized by high-energy ball-milling after 12 h from a powders mixture of zinc oxide (ZnO) and hematite (α-Fe₂O₃) with balls to powders mass ratio of 20:1. X-ray diffraction, vibrating sample magnetometer (VSM), the Mössbauer spectrometry and photoluminescence (PL) are used to characterize the samples. Rietveld analysis and VSM measurements show that the powder has an average crystallites size of 10 nm and a ferrimagnetic behavior with a saturation magnetization of 30 emu/g. After annealing at 700 °C, the lattice parameter reduces from 8.448 to 8.427 Å and the sample transforms into a superparamagnetic behavior, which was confirmed as well by the room temperature Mössbauer spectrometry. Different mechanisms to explain the obtained results and the correlation between magnetism and structure are discussed. Finally, the broadband visible emission band is observed in the entire PL spectrum and the estimated energy band gap is about 2.13 eV.     

Spectroscopic study of ZnO doped CeO2-PbO-B2O3 glasses

Glass samples of compositions xZnO-xCeO₂-(30−x)PbO-(70−x)B₂O₃ with x varying from 2% to 10% mole fraction are prepared by the melt quench technique. The structural and optical analysis of glasses is carried out by XRD, FTIR, density and UV-visible spectroscopic measurement techniques. The FTIR spectral analysis indicates that with the addition of ZnO contents in glass network, structural units of BO₃ are transformed into BO₄. It has been observed in our previous work that band gap decreases from 2.89 to 2.30 eV for CeO₂-PbO-B₂O₃ glasses with cerium content varying from 0% to 10% [Gurinder Pal Singh, Davinder Paul Singh, Physica B 406(3) (2011) 640-644]. With the incorporation of zinc in CeO₂-PbO-B₂O₃ glasses, the optical band gap energy decreases further from 2.38 to 2.03 eV. This causes more compaction of the borate network, which results in an increase of density (3.39-4.02 g/cm³). Transmittance shows that ZnO in glass samples acts as a reducing agent thathelps to convert Ce⁴⁺→Ce³⁺ ions.     

Luminescence of ZnWO4 and CdWO4 thin films prepared by spray pyrolysis

Thin films of ZnWO₄ and CdWO₄ were prepared by spray pyrolysis and the structural, optical, and luminescence properties were investigated. Both ZnWO₄ and CdWO₄ thin films showed a broad blue-green emission band. The broad band of ZnWO₄ films was centered at 495 nm (2.51 eV) consisted of three bands at 444 nm (2.80 eV), 495 nm (2.51 eV) and 540 nm (2.30 eV). The broad band of CdWO₄ films at 495 nm (2.51 eV) could be decomposed to three bands at 444 nm (2.80 eV), 495 nm (2.51 eV) and 545 nm (2.28 eV). These results are consistent with emission from the WO₆⁶⁻ molecular complex. The luminance and efficiency for ZnWO₄ film at 5 kV and 57 μA/cm² were 48 cd/m² and 0.22 lm/w, respectively, and for CdWO₄ film the values were 420 cd/m² and 1.9 lm/w.     

Dy3+ emission in M5(PO4)3F (M = Ca, Ba) phosphor

Ultrafine M₅(PO₄)₃F:Dy³⁺ (M = Ca, Ba) phosphors were prepared via combustion process using metal nitrates as precursors. The formation of crystalline phosphate was confirmed by X-ray diffraction pattern. The PL excitation spectra show the excitation peaks observed at 250 to 400 nm due to f → f transition of Dy³⁺ ion, which are useful for solid-state lighting purpose (mercury free excitation). The PL emission of Dy³⁺ ion by 348 nm excitation gave an emission at 489 nm (blue), 582 nm (yellow) and 675 nm (red). All the characteristics of BYR emissions like BGR indicate that Dy doped Ca₅(PO₄)₃F and Ba₅(PO₄)₃F phosphors are good candidates that can be applied in solid-state lighting phosphor (mercury free excited lamp phosphor) and white light LED.      

Synthesis of ZnO nanostructures with controlled morphology and size in ionic liquids

Nanostructured ZnO has been synthesized by a hydrothermal route, using different ionic liquids (ILs) as the morphology templates. The morphology of ZnO changes from rod-like to star-like and flower-like in different ILs. A 3D nano/micro structure ZnO with unique flower-like morphology has been synthesized via the assembly of dicationic IL and [Zn(OH)₄]²⁻. The flower-like pattern was obtained in the presence of IL 1. The flower-like ZnO structure has a hexagonal prism, with a hexagonal pyramid on the tip, and diameter of ~444 nm. While the ZnO prepared in IL 2, shows uniform rod-like shape with a diameter of 91 nm, star-like morphology consisting of nanorods with diameter of ~109 nm was formed in IL 3. The XRD, SEM, and PL spectra have been employed for characterization of the synthesized ZnO nano structures.     

Modified thermal evaporation process using GeO2 for growing ZnO structures

In the current work, zinc oxide (ZnO) nano/microstructures are synthesized using a modified thermal-evaporation process by introducing germanium oxide (GeO₂) powder mixed with metallic Zn powder as the raw material. Without the use of any catalyst and oxygen flow in the furnace system, GeO₂ is utilized to provide an oxygen source for the growth of ZnO structure. The samples are treated by different temperatures ranging from 500 to 900 °C. Morphology, phase structure, and photoluminescence properties are investigated by scanning electron microscopy (SEM), X-ray diffractometer (XRD) and photoluminescence (PL) spectrometer. The structures and morphologies of the samples were found to vary with growth temperature. The XRD diffraction peaks show that the films grown at temperature from 600 to 800 °C consist of hexagonal wurtzite ZnO structures. Room-temperature PL measurement revealed ZnO spectra representing two bands: near-band-edge emission in the ultraviolet (UV) region and broad deep-level emission centered at about 500 nm. The strong UV emission in the PL spectra indicates that the GeO₂ supplies sufficient oxygen for formation of ZnO structures with few oxygen vacancies. The growth mechanism and the roles of GeO₂ for formation of ZnO structures are discussed in detail.     

Synthesis of ZnO2 nanoparticles by laser ablation in liquid and their annealing transformation into ZnO nanoparticles

A pulsed laser emitting UV radiations generated by the third harmonic of Nd:YAG was applied for the synthesis of nano-structured ZnO₂ and ZnO. For the synthesis of nanoparticles of ZnO₂, a high-purity metallic plate of Zn target was fixed at the bottom of a glass cell, in the presence of deionized water mixed with oxidizing agent H₂O₂, under repeated laser irradiation. The optical properties, size and the morphology of the synthesized ZnO₂ and ZnO by laser ablation was influenced strongly by post-annealing conditions which is not previously reported. By annealing ZnO₂ at 200 °C for 8 h, the product (ZnO₂) synthesized primarily was converted completely to ZnO. By variation of the annealing temperatures from 200 to 600 °C, the grain size of ZnO changes from 5 to 19 nm with a change in lattice parameters, the band gap and some other optical properties of nano-ZnO.     

Structural, optical and electrical properties of ZnO/Zn2GeO4 porous-like thin film and wires

Zinc oxide/zinc germanium oxide (ZnO/Zn₂GeO₄) porous-like thin film and wires has been fabricated by simple thermal evaporation method at temperature about 1120 °C for 2.5 h. The structural and optical properties of the porous-like-thin film and wires have been investigated by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) and photoluminescence (PL) spectroscopy. Metal semiconductor metal (MSM) photodetector structure was used to evaluate the electrical characteristics by using current-voltage (I-V) measurements. Room temperature photoluminescence spectrum of the sample shows one prominent ultraviolet peak at 378 nm and a shoulder at 370 nm. In addition, broad visible blue emission peak at wavelength 480 nm and green emission peak at 500 nm are also observed. Strong photoelectric properties of the MSM in the UV demonstrated that the porous-like-thin film and wires contribute to its photosensitivity and therefore making ZnO/Zn₂GeO₄ wires potential photodetector in the shorter wavelength applications.     

掺Bi钨酸镉单晶体发光特性的研究

用坩埚下降法(Bridgman)生长出了Bi离子掺杂的CdWO₄单晶.测定了晶体不同部位的吸收光谱、发射光谱和X射线电子能谱(XPS).Bi离子的掺入引起CdWO₄晶体的吸收边从345 nm红移到399 nm.在311 nm, 373 nm,808 nm和980 nm光的激发下,分别观测到中心波长为470 nm,528 nm,1078 nm和较弱的1504 nm四个不同发射带.Bi:CdWO₄单晶的XPS谱分别与Bi₂ 关键词： Bi离子 荧光光谱 X射线电子能谱 4单晶')" href="#">CdWO₄单晶     

Enhancing the crystallinity and surface roughness of sputtered TiO2 thin film by ZnO underlayer

TiO₂ and TiO₂/ZnO double layer films were sputtered on glass substrates. It was found that a thin ZnO underlayer is helpful for tailoring the microstructure and surface morphology of the TiO₂ film. By applying a 70-nm-thick ZnO underlayer, a TiO₂ thin film of 100 nm in thickness with well crystallized anatase phase and rough surface was successfully fabricated without heating the substrate. Relatively high photo-catalytic activity and good hydrophilic properties were observed in such TiO₂/ZnO double layer films.