One‐pot synthesis of magnetic zeolitic imidazolate framework/grapheme oxide composites for the extraction of neonicotinoid insecticides from environmental water samples

Magnetic zeolitic imidazolate framework 67/graphene oxide composites were synthesized by one‐pot method at room temperature for the first time. Electrostatic interactions between positively charged metal ions and both negatively charged graphene oxide and Fe₃O₄ nanoparticles were expected to chemically stabilize magnetic composites to generate homogeneous magnetic products. The additional amount of graphene oxide and stirring time of graphene oxide, Co²⁺, and Fe₃O₄ solution were investigated. The zeolitic imidazolate framework 67 and Fe₃O₄ nanoparticles were uniformly attached on the surface of graphene oxide. The composites were applied to magnetic solid‐phase extraction of five neonicotinoid insecticides in environmental water samples. The main experimental parameters such as amount of added magnetic composites, extraction pH, ionic strength, and desorption solvent were optimized to increase the capacity of adsorbing neonicotinoid insecticides. The results show limits of detection at signal‐to‐noise ratio of 3 were 0.06–1.0 ng/mL under optimal conditions. All analytes exhibited good linearity with correlation coefficients of higher than 0.9915. The relative standard deviations for five neonicotinoid insecticides in environmental samples ranged from 1.8 to 16.5%, and good recoveries from 83.5 to 117.0% were obtained, indicating that magnetic zeolitic imidazolate framework 67/graphene oxide composites were feasible for analysis of trace analytes in environmental water samples.     

Mild Synthesis of Pt/SnO2/Graphene Nanocomposites with Remarkably Enhanced Ethanol Electro‐oxidation Activity and Durability

We have designed a new Pt/SnO₂/graphene nanomaterial by using L ‐arginine as a linker; this material shows the unique Pt‐around‐SnO₂ structure. The Sn²⁺ cations reduce graphene oxide (GO), leading to the in situ formation of SnO₂/graphene hybrids. L ‐Arginine is used as a linker and protector to induce the in situ growth of Pt nanoparticles (NPs) connected with SnO₂ NPs and impede the agglomeration of Pt NPs. The obtained Pt/SnO₂/graphene composites exhibit superior electrocatalytic activity and stability for the ethanol oxidation reaction as compared with the commercial Pt/C catalyst owing to the close‐connected structure between the Pt NPs and SnO₂ NPs. This work should have a great impact on the rational design of future metal–metal oxide nanostructures with high catalytic activity and stability for fuel cell systems.     

Synthesis of Ultrastable Ag Nanoplates/Polyethylenimine–Reduced Graphene Oxide and Its Application as a Versatile Electrochemical Sensor

Investigations on Ag nanostructures/reduced graphene oxide composites have been frequently reported, yet the morphology control of those loaded Ag nanocrystals is still challenging. We herein develop a facile method to grow triangular Ag nanoplates (AgP) on polyethylenimine‐modified reduced graphene oxide (AgP/PEI‐rGO). The AgP/PEI‐rGO hybrids show unexpected high stability against chloride ions (Cl^?) and hydrogen peroxide (H₂O₂), which is possibly due to the strong interaction between surface Ag atoms with the amine groups of PEI. In the chronoamperometry measurements for detecting H₂O₂, N₂H₄, and NaNO₂, the AgP/PEI‐rGO hybrid shows very wide linear ranges (usually 10^?6–10^?2 mol L^?1 for H₂O₂, N₂H₄, and NaNO₂) and low detection limits (down to ≈1×10^?7 mol L^?1), which demonstrate the promising electrochemical sensor applications of these metal/graphene hybrids with well‐defined morphologies and facets. In addition, this strategy could be extended to the deposition of other noble metals on rGO with controlled morphologies.     

Graphene wrapped phthalocyanine: Enhanced oxidative desulfurization for dibenzothiophene in fuel

Graphene wrapped metal phthalocyanine (MPc/RGO, M = Mn²⁺, Fe²⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺) composites are synthesized by a facile ‘in situ hydrothermal’ method, using graphene oxide, M (CH₃COO)₂ and phthalic anhydride as the precursors. A biomimetic catalytic system of MPc/RGO and molecular O₂ have high activity for ultra‐deep removal of dibenzothiophene (DBT) in model oil containing n‐octane. Compared with pure graphene oxide and MPc, MPc/RGO composites displayed highly enhanced catalytic activity for the oxidation of dibenzothiophene in n‐octane. The conversion ratio of DBT was up to 97.51% after 180 min treatment at 60 °C and atmospheric pressure. The photostability of RGO/MPc composites photocatalystic degradation of dibenzothiophene was investigated. Mechanistic studies revealed that the RGO/MPc ? O₂ · species were the main active intermediate via the π‐π stacking interaction of MPc and RGO. The RGO wrapped phthalocyanine materials offer great potential as active photocatalysts for degradation of thiophene derivatives in fuel.     

A High-Performance Asymmetric Supercapacitor Based on Tungsten Oxide Nanoplates and Highly Reduced Graphene Oxide Electrodes

Tungsten oxide/graphene hybrid materials are attractive semiconductors for energy-related applications. Herein, we report an asymmetric supercapacitor (ASC, HRG//m-WO₃ ASC), fabricated from monoclinic tungsten oxide (m-WO₃) nanoplates as a negative electrode and highly reduced graphene oxide (HRG) as a positive electrode material. The supercapacitor performance of the prepared electrodes was evaluated in an aqueous electrolyte (1 m H₂SO₄) using three- and two-electrode systems. The HRG//m-WO₃ ASC exhibits a maximum specific capacitance of 389 F g⁻¹ at a current density of 0.5 A g⁻¹, with an associated high energy density of 93 Wh kg⁻¹ at a power density of 500 W kg⁻¹ in a wide 1.6 V operating potential window. In addition, the HRG//m-WO₃ ASC displays long-term cycling stability, maintaining 92 % of the original specific capacitance after 5000 galvanostatic charge–discharge cycles. The m-WO₃ nanoplates were prepared hydrothermally while HRG was synthesized by a modified Hummers method.     

Metal Oxide‐Coated Three‐Dimensional Graphene Prepared by the Use of Metal–Organic Frameworks as Precursors

A simple method for the preparation of metal‐oxide‐coated three‐dimensional (3D) graphene composites was developed. The metal–organic frameworks (MOFs) that served as the precursors of the metal oxides were first synthesized on the 3D graphene networks (3DGNs). The desired metal oxide/3DGN composites were then obtained by a two‐step annealing process. As a proof‐of‐concept application, the obtained ZnO/3DGN and Fe₂O₃/3DGN materials were used in a photocatalytic reaction and a lithium‐ion battery, respectively. We believe this method could be extended to the synthesis of other metal oxide/3DGN composites with 3D structures simply through the appropriate choice of specific MOFs as precursors.     

Graphene‐Assisted Room‐Temperature Synthesis of 2D Nanostructured Hybrid Electrode Materials: Dramatic Acceleration of the Formation Rate of 2D Metal Oxide Nanoplates Induced by Reduced Graphene Oxide Nanosheets

A new prompt room temperature synthetic route to 2D nanostructured metal oxide–graphene‐hybrid electrode materials can be developed by the application of colloidal reduced graphene oxide (RGO) nanosheets as an efficient reaction accelerator for the synthesis of δ‐MnO₂ 2D nanoplates. Whereas the synthesis of the 2D nanostructured δ‐MnO₂ at room temperature requires treating divalent manganese compounds with persulfate ions for at least 24 h, the addition of RGO nanosheet causes a dramatic shortening of synthesis time to 1 h, underscoring its effectiveness for the promotion of the formation of 2D nanostructured metal oxide. To the best of our knowledge, this is the first example of the accelerated synthesis of 2D nanostructured hybrid material induced by the RGO nanosheets. The observed acceleration of nanoplate formation upon the addition of RGO nanosheets is attributable to the enhancement of the oxidizing power of persulfate ions, the increase of the solubility of precursor MnCO₃, and the promoted crystal growth of δ‐MnO₂ 2D nanoplates. The resulting hybridization between RGO nanosheets and δ‐MnO₂ nanoplates is quite powerful not only in increasing the surface area of manganese oxide nanoplate but also in enhancing its electrochemical activity. Of prime importance is that the present δ‐MnO₂–RGO nanocomposites show much superior electrode performance over most of 2D nanostructured manganate systems including a similar porous assembly of RGO and layered MnO₂ nanosheets. This result underscores that the present RGO‐assisted solution‐based synthesis can provide a prompt and scalable method to produce nanostructured hybrid electrode materials.     

金红石相TiO2-石墨烯复合材料的制备及其光催化性能

以鳞片石墨为原料, 用改进的Hummers法制备氧化石墨烯(GO), 以异丙醇钛为钛源经一步水热法制备得到金红石相TiO₂-石墨烯复合材料(rGO-TiO₂), 考察了氧化石墨烯用量对复合材料光催化性能的影响. 采用X射线衍射(XRD), 比表面积(BET), 透射电镜(TEM), 扫描电镜(SEM), 拉曼光谱, 紫外-可见(UV-Vis)吸收光谱和荧光光谱(PL)等测试手段对复合材料进行表征. 结果表明: 复合材料中TiO₂为针簇状结构的金红石相, 与石墨烯能够均匀复合; 与纯金红石相TiO₂相比, 复合材料具有较大的比表面积. 研究了该复合材料在紫外光下对罗丹明B 以及可见光下对甲基橙光降解效果. 当氧化石墨烯浓度为0.5 mg·mL^-1时, 制备得到的复合材料rGO-TiO₂具有较好的光催化效果.     

碳和石墨烯对磷酸锰锂材料性能的影响

在采用溶剂热法制备磷酸锰锂的基础上,以蔗糖和石墨烯为碳源,制备了裂解碳和石墨烯含量不同的磷酸锰锂/碳/石墨烯复合材料,研究了裂解碳和石墨烯对材料性能的影响。采用扫描电镜(SEM)和透射电镜(TEM)对材料的形貌进行了表征。裂解碳包覆可以提高LiMnPO_4纳米片表面的电子导电性,对于材料性能的改善起到主要的作用;石墨烯可以提高纳米片之间的电子和离子导电性,改善材料的电化学性能。电化学测试表明,当裂解碳含量为4%、石墨烯含量为2%时,LiMnPO_4电极具有较好的电化学性能,在0.5C下的放电比容量为139.1 m Ah·g-1,循环100次后,容量保持率为93.6%。与添加单一碳和单一石墨烯的LiMnPO_4电极相比,该电极在0.5C下的放电比容量分别提高了35.0%和48.6%。     

碳和石墨烯对磷酸锰锂材料性能的影响

在采用溶剂热法制备磷酸锰锂的基础上,以蔗糖和石墨烯为碳源,制备了裂解碳和石墨烯含量不同的磷酸锰锂/碳/石墨烯复合材料,研究了裂解碳和石墨烯对材料性能的影响。采用扫描电镜（SEM）和透射电镜（TEM）对材料的形貌进行了表征。裂解碳包覆可以提高LiMnPO₄纳米片表面的电子导电性,对于材料性能的改善起到主要的作用;石墨烯可以提高纳米片之间的电子和离子导电性,改善材料的电化学性能。电化学测试表明,当裂解碳含量为4%、石墨烯含量为2%时,LiMnPO₄电极具有较好的电化学性能,在0.5C下的放电比容量为139.1 mAh·g^-1,循环100次后,容量保持率为93.6%。与添加单一碳和单一石墨烯的LiMnPO₄电极相比,该电极在0.5C下的放电比容量分别提高了35.0%和48.6%。     

Flower-like SnO2 nanoparticles grown on graphene as anode materials for lithium-ion batteries

Tin oxide (SnO₂)/graphene composite was synthesized from SnCl₂?·?2H₂O and graphene oxide (GO) by a wet chemical-hydrothermal route. The GO was reduced to graphene nanosheet (GNS) and flower-like SnO₂ nano-crystals with size about 40 nm were homogeneously distributed on the surface of GNS. The SnO₂/graphene composites delivered a superior first discharge capacity of 1941.9 mAhg^?1 with a reversible capacity of 901.7 mAhg^?1 at the current density of 100 mAg^?1. Moreover, even at higher densities of 200 and 500 mAg^?1, the SnO₂/graphene composite still maintained enhanced cycling stability. After 40 cycles, the discharge capacity was still maintained at 691.1 mAhg^?1 at the current density of 100 mAg^?1. The SnO₂/graphene composite displayed an outstanding Li-battery performance with large reversible capacity and enhanced rate performance, which can be attributed to the highly uniform distribution of SnO₂ nanoparticles and high reduction degree of graphene. This result strongly indicates that the SnO₂/graphene composite was a promising anode material in high-performance lithium-ion batteries.     

石墨烯/硫复合正极材料的一步水热法制备与电化学性能

将硫代硫酸钠（Na₂S₂O₃）与氧化石墨烯（GO）的混合溶液,在酸性条件下经过一步水热反应制备还原氧化石墨烯/硫（RGO/S）复合正极材料. 实验探索了水热温度、反应时间、碳硫质量比例对材料的影响. 通过X射线衍射（XRD）、扫描电镜（SEM）、透射电镜（TEM）和恒电流充放电对材料进行分析. 结果表明在180 ℃下,碳硫质量比为3：7时,水热12 h得到的RGO/S复合材料具有优异的循环性能,首次放电比容量为931 mAh·g^-1,50次循环之后其比容量还保持在828.16 mAh·g^-1;RGO/S复合材料的充放电库仑效率在95%以上;同时RGO/S复合材料的倍率性能相比于单质硫有很大提高. 一步水热法能够使硫分子均匀分布在石墨烯片层结构中,同时加强了石墨烯表面基团对硫分子的固定作用.     

Preparation,properties, and catalytic activity of platinum-modified plasma electrolytic oxide structures on aluminum

Catalytically active Pt-containing oxide composites on aluminum have been prepared by plasma electrolytic oxidation (PEO) and by additional modification of the resulting coating by impregnation with an aqueous solution of chloroplatinic acid followed by calcination. The oxide film/metal composites have been characterized by X-ray diffraction, X-ray photoelectron spectroscopy, and electron microscopy. The modified films contain the γ-Al₂O₃ and Pt crystalline phases. Platinum in the surface and subsurface layers is in the Pt⁰ state. There are platinum-rich areas on the surface of the PEO films. A higher catalytic activity in CO oxidation into CO₂ is shown by the samples whose oxide film contains nickel and copper along with platinum.     

Synthesis and characterization of graphene oxide‐based hybrid ligand and its metal complexes: Highly efficient sensor and catalytic properties

A new graphene oxide‐based hybrid material (HL) and its Co(II), Cu(II) and Ni(II) metal complexes were prepared. Firstly, graphene oxide and (3‐aminopropyl)trimethoxysilane were reacted to give graphene oxide–3‐(aminopropyl)trimethoxysilane (GO‐APTMS) hybrid material. After that, hybrid material HL was synthesized from the reaction of GO‐APTMS and 2,6‐diformyl‐4‐methylphenol. Finally, Co(II), Cu(II) and Ni(II) complexes of HL were obtained. All the materials were characterized using various techniques. The chemosensor properties of HL were investigated against Na⁺, K⁺, Cd²⁺, Co²⁺, Cu²⁺, Hg²⁺, Ni²⁺, Zn²⁺, Al³⁺, Cr³⁺, Fe³⁺ and Mn³⁺ ions and it was found that HL has selective chemosensing to Fe³⁺ ion. All the graphene oxide‐supported complexes were used as heterogeneous catalysts in the oxidation of 2‐methylnaphthalene (2MN) to 2‐methyl‐1,4‐naphthoquinone (vitamin K₃, menadione) in the presence of hydrogen peroxide, acetic acid and sulfuric acid. The Cu(II) complex showed good catalytic properties compared to the literature. The selectivity of 2MN to vitamin K₃ was 60.23% with 99.75% conversion using the Cu(II) complex.     

Preparation and thermal reactivity of some rare earth and uranyl hydrazinesulfinates and sulfite hydrazinates

Hydrazinesulfinate and sulfite hydrazinate derivatives of rare earth elements of composition Ln(N₂H₃SOO)₃(H₂O) and Ln₂(SO₃)₃(N₂H₄)_x(H₂O)_y, respectively, where Ln=La, Ce, Pr, Nd and Sm, have been prepared and characterized by chemical analysis and infrared spectra. The uranyl complexes of the composition UO₂(N₂H₃SOO)₂, UO₂(N₂H₃SOO)₂(N₂H₄) and UO₂SO₃(N₂H₄)(H₂O) have also been prepared under different reaction conditions and studied by different physicochemical techniques. Thermal properties of all these complexes have been studied by thermogravimetry, and differential scanning calorimetry. The hydrazinesulfinate derivatives of rare earth elements undergo thermal decomposition in multisteps to give the respective metal sulfate as the residue. The other series of complexes, viz., rare earth sulfite hydrazinates gave a mixture of metal sulfate and metal oxide as the end products. However, all the uranyl complexes undergo decomposition in air to give UO₂SO₃ as the final product.     

X-ray absorption fine structure study of amorphous metal oxide thin films prepared by photochemical metalorganic deposition

The oxidation state and local geometry of the metal centers in amorphous thin films of Fe₂O₃ (Fe³⁺ oxidation state), CoFe₂O₄ (Co²⁺/Fe³⁺ oxidation states), and Cr₂O₃ (Cr³⁺ oxidation state) are determined using K edge X-ray absorption near-edge structure (XANES) spectroscopy and extended X-ray absorption fine structure (EXAFS) spectroscopy. The metal oxide thin films were prepared by the solid-state photochemical decomposition of the relevant metal 2-ethylhexanoates, spin cast as thin films. No peaks are observed in the X-ray diffraction patterns, indicating the metal oxides are X-ray amorphous. The oxidation state of the metals is determined from the edge position of the K absorption edges, and in the case of iron-containing samples, an analysis of the pre-edge peaks. In all cases, the EXAFS analysis indicates the first coordination shell consists of oxygen atoms in an octahedral geometry, with a second shell consisting of metals. No higher shells are observed beyond 3.5 Å for all samples, indicating the metal oxides are truly amorphous, consistent with X-ray diffraction results.     

Al3+/graphene composites for electrochemical detection of DNA cleavage

Herein, we present the electrochemical co-deposition of Al3+/graphene composites directly from an aqueous mixture containing graphene oxide (GO) and Al3+. The obtained Al3+/graphene composites with good electrochemical activity were regarded as an appropriate immobilization platform for double-stranded DNA (dsDNA). The nontoxic redox probe xanthurenic acid (XA) was successfully applied to recognize single-stranded DNA and dsDNA. We illustrated that the scission of dsDNA caused by GO combining with some metal ions could be detected by monitoring the electrochemical signals of XA.     

Ni0.8Co0.15Al0.05C2O4@Graphene的合成及电化学性能研究

过渡金属氧化物/石墨烯复合材料具有优异的电化学性能被广泛应用在锂离子电池中。本文以硫酸镍、硫酸钴、硫酸铝、草酸为原料按一定的物质的量比配制成溶液,在120°C的条件下水热反应12小时,得到多元过渡金属氧化物前驱体Ni_0.8Co_0.15Al_0.05C₂O₄(NCA-C₂O₄);该前驱体经聚烯丙基胺盐酸盐修饰后,与氧化石墨烯进行复合并还原得到石墨烯包覆的多元过渡金属氧化物/石墨烯负极材料Ni_0.8Co_0.15Al_0.05C₂O₄@Graphene(NCA-C₂O₄@G)。对材料的结构、形貌和电化学性质进行了表征。扫描电镜测试结果显示样品粒度均一,具有两端不规则长方体形貌。电化学性能测试结果表明：石墨烯包覆后的NCA-C₂O₄@G充放电容量高于前驱体NCA-C₂O₄,NCA-C₂O₄@G复合材料在0.1C电流密度 (1C=1000 mAh/g)下首次放电比容量为1956 mA h/g;经过0.1C、0.2C、0.5C、1C、2C高倍率循环后,当测试电流密度恢复至100 mA/g时,复合材料比容量可迅速回升至720 mA h/g,并在随后50次循环中比容量保持稳定,显示出良好的循环稳定性和倍率性能。     

One-pot synthesis of graphene–cuprous oxide composite with enhanced photocatalytic activity

In this paper, graphene–cuprous oxide (G–Cu₂O) composites were synthesized at room temperature using graphene oxide (GO) as two-dimensional support. From Zeta potential analysis, the surface charge of G–Cu₂O composites altered from positive to negative, which favors the adsorption and photodegradation of positively charged dyes. Compared with Cu₂O under similar synthesis condition, the G–Cu₂O composites demonstrated improved photodegradation activity for methylene blue (MB) dye under visible light. Controlled experiments indicated that the G–Cu₂O composite synthesized with 80 mg GO in the reaction system possessed more negative Zeta potential, highest specific surface area and thus presented the highest photocatalytic activity. Electrons mechanism for the improved photocatalytic performance of G–Cu₂O composite was proposed in the degradation of MB.     

Tungsten Oxide Nanoplates; the Novelty in Targeting Metalloproteinase-7 Gene in Both Cervix and Colon Cancer Cells

In this study, we synthesized tungsten oxide (WO₃) nanoplates, both crystallographic phases and the morphology of the samples were determined by powder x-ray diffraction and the scanning electron microscopy, respectively. The obtained data clarified that, the all prepared WO₃·H₂O samples were composed of large quantity of nanoplates. The cytotoxicity patterns of nanoplates were checked on both normal and cancer mammalian cell lines. Both nanoplates cytotoxicity did not exceed the 50 % inhibitory concentration (IC50) on the all normal tested cells even by using concentrations up to 1 mg/ml. In addition, orthorhombic tungsten oxide nanoplate was more potent against both Caco2 and Hela cells by showing inhibition percentages in cellular viability 64.749 and 72.27, respectively, and with cancer selectivity index reached 3.2 and 2.6 on both colon and cervix cancer, respectively. The anticancer effects of nanoplates were translated to alteration in both pro-apoptotic and anti-apoptotic genes expressions. Tungsten oxide nanoplates down regulated the expression of B cell lymphoma 2 (Bcl-2) and metalloproteinase-7 (MMP7) genes. In addition, orthorhombic tungsten oxide nanoplates showed more potentiation in IL2 and IL8 induction (40.43 pg/ml) and upregulation of TNF-α gene expression but with lower folds than Escherichia coli lipopolysaccharide (LPS) induction.