Effect of capping and particle size on Raman laser-induced degradation of γ-Fe2O3 nanoparticles

Diol capped γ-Fe₂O₃ nanoparticles are prepared from ferric nitrate by refluxing in 1,4-butanediol (9.5 nm) and 1,5-pentanediol (15 nm) and uncapped particles are prepared by refluxing in 1,2-propanediol followed by sintering the alkoxide formed. X-ray diffraction (XRD) shows that all the samples have the spinel phase. Raman spectroscopy shows that the samples prepared in 1,4-butanediol and 1,5-pentanediol and 1,2-propanediol (sintered at 573 and 673 K) are γ-Fe₂O₃ and the 773 K-sintered sample is Fe₃O₄. Raman laser studies carried out at various laser powers show that all the samples undergo laser-induced degradation to α-Fe₂O₃ at higher laser power. The capped samples are however, found more stable to degradation than the uncapped samples. The stability of γ-Fe₂O₃ sample with large particle size (15.4 nm) is more than the sample with small particle size (10.2 nm). Fe₃O₄ having a particle size of 48 nm is however less stable than the smaller γ-Fe₂O₃ nanoparticles.     

Kinetics of reduction of iron oxides by H2: Part II. Low temperature reduction of magnetite

This study deals with the reduction of Fe₃O₄ by H₂ in the temperature range of 210-950 °C. Two samples of Fe₃O₄ produced at 600 and 1200 °C, designated as Fe₃O₄₍₆₀₀₎ and Fe₃O_4(1200), have been used as starting material.Reduction of Fe₃O₄₍₆₀₀₎ by H₂ is characterized by an apparent activation energy ‘E_a’ of 200, 71 and 44 kJ/mol at T < 250 °C, 250 °C < T < 390 °C and T > 390 °C, respectively. The important change of E_a at 250 °C could be attributed to the removal of hydroxyl group and/or point defects of magnetite. This is confirmed during the reduction of Fe₃O_4(1200). While transition at T ≈ 390 °C is probably due to sintering of the reaction products as revealed by SEM.In situ X-rays diffraction reduction experiments confirm the formation of stoichiometric FeO between 390 and 570 °C. At higher temperatures, non-stoichiometric wüstite is the intermediate product of the reduction of Fe₃O₄ to Fe.The physical and chemical modifications of the reduction products at about 400 °C, had been confirmed by the reduction of Fe₃O₄₍₆₀₀₎ by CO and that of Fe₃O_4(1200) by H₂. A minimum reaction rate had been observed during the reduction of Fe₃O_4(1200) at about 760 °C. Mathematical modeling of experimental data suggests that the reaction rate is controlled by diffusion and SEM observations confirm the sintering of the reaction products.Finally, one may underline that the rate of reduction of Fe₃O₄ with H₂ is systematically higher than that obtained by CO in the explored temperature range.     

Preparation of Fe3O4 nanoparticle enclosure hydroxylated multi-walled carbon nanotubes for the determination of aconitines in human serum samples

A magnetic carbon nanomaterial for Fe₃O₄ enclosure hydroxylated multi-walled carbon nanotubes (Fe₃O₄-EC-MWCNTs-OH) was prepared by the aggregating effect of Fe₃O₄ nanoparticle on MWCNTs-OH, and combined with high-performance liquid chromatography (HPLC)/diode array detection (DAD) to determine the aconitines (aconitine, hypaconitine and mesaconitine) in human serum samples. Compared with other extraction modes investigated in experiment, Fe₃O₄-EC-MWCNTs-OH sorbents showed a good affinity to target analytes. Some important parameters that could influence extraction efficiency of aconitines, including the extraction mode, amounts of Fe₃O₄-EC-MWCNTs-OH, pH of sample solution, extraction time, desorption solvent and desorption time, were optimized. Under optimal conditions, the recoveries of spiked serum samples were between 98.0% and 103.0%; relative standard deviations (RSDs) ranged from 0.9% to 6.2%. The correlation coefficients varied from 0.9996 to 0.9998. The limits of detection ranged from 3.1 ng mL⁻¹ to 4.1 ng mL⁻¹ at a signal-to-noise ratio of 3. The experimental results showed that the proposed method was feasible for the analysis of aconitines in serum samples.     

Preparation of carbon coated Fe3O4 nanoparticles and their application for solid-phase extraction of polycyclic aromatic hydrocarbons from environmental water samples

The carbon coated Fe₃O₄ nanoparticles (Fe₃O₄/C) were synthesized by a simple hydrothermal reaction and applied as solid-phase extraction (SPE) sorbents to extract trace polycyclic aromatic hydrocarbons (PAHs) from environmental water samples. The Fe₃O₄/C sorbents possess high adsorption capacity and extraction efficiency due to strong adsorption ability of carbon materials and large surface area of nanoparticles, and only 50 mg of sorbents are required to extract PAHs from 1000 mL water samples. The adsorption attains equilibrium rapidly and analytes are eluted with acetonitrile readily. Salinity and solution pH have no obvious effect on the recoveries of PAHs, which avoids fussy adjustment to water sample before extraction. Under optimized conditions, the detection limits of PAHs are in the range of 0.2–0.6 ng L⁻¹. The accuracy of the method was evaluated by the recoveries of spiked samples. Good recoveries (76–110%) with low relative standard deviations from 0.8% to 9.7% are achieved. This new SPE method provides several advantages, such as high extraction efficiency, high breakthrough volumes, convenient extraction procedure, and short analysis times. To our knowledge, this is the first time that Fe₃O₄/C nanoparticles are used for the pretreatment of environmental water samples.     

Facile synthesis of multifunctional multiwalled carbon nanotubes/Fe3O4 nanoparticles/polyaniline composite nanotubes

With an average diameter of 100-150 nm, composite nanotubes of polyaniline (PANI)/multiwalled carbon nanotubes (MWNTs) containing Fe₃O₄ nanoparticles (NPs) were synthesized by a two-step method. First, we synthesized monodispersed Fe₃O₄ NPs (d=17.6 nm, σ=1.92 nm) on the surface of MWNTs and then decorated the nanocomposites with a PANI layer via a self-assembly method. SEM and TEM images indicated that the obtained samples had the morphologies of nanotubes. The molecular structure and composition of MWNTs/Fe₃O₄ NPs/PANI nanotubes were characterized by Fourier transform infrared spectra (FTIR), energy dispersive X-ray spectrometry (EDX), X-ray photoelectron spectra (XPS), X-ray diffraction (XRD) and Raman spectra. UV-vis spectra confirmed the existence of PANI and its response to acid and alkali. As a multifunctional material, the conductivity and magnetic properties of MWNTs/Fe₃O₄ NPs/PANI composites nanotubes were also investigated.     

Mild hydrothermal synthesis and ferrimagnetism of Pr3Fe5O12 and Nd3Fe5O12 garnets

Two pure light rare earth iron garnets Pr₃Fe₅O₁₂ and Nd₃Fe₅O₁₂ single crystals were synthesized under mild hydrothermal conditions and structurally characterized by single crystal and powder X-ray diffraction methods. Both compounds crystallize in cubic space group Ia3?d with lattice parameters a=12.670(2) Å for Pr₃Fe₅O₁₂ and a=12.633(2) Å for Nd₃Fe₅O₁₂, respectively. The synthesis of compounds was studied with regard to phase evolution and morphology development with hydrothermal conditions. We proposed the formation mechanisms and formulated a reasonable explanation for their growth habits. Ferrimagnetic Curie temperatures which have been inferred from thermo-magnetization curves were 580 K for Pr₃Fe₅O₁₂ and 565 K for Nd₃Fe₅O₁₂, and the transitions of long range order were also evidenced by differential scanning calorimetry method. The result of magnetic properties has shown that moments of the large radius Pr³⁺ and Nd³⁺ ions are parallelly coupled with net moments of iron ions.     

Polythiophene-coated Fe3O4 superparamagnetic nanocomposite: Synthesis and application as a new sorbent for solid-phase extraction

In the present work, a novel type of superparamagnetic nanosorbent, polythiophene-coated Fe₃O₄ nanoparticles (Fe₃O₄@PTh NPs), have been successfully synthesized. The synthesized NPs were characterized by scanning electron microscopy (SEM), Fourier transform-infrared (FT-IR) spectroscopy, and thermal gravimetric analysis (TGA). The synthesized Fe₃O₄@PTh NPs were applied as an efficient sorbent for extraction and preconcentration of several typical plasticizer compounds (di-n-butyl phthalate (DBP), di-(2-ethylhexyl) phthalate (DEHP), and dioctyl adipate (DOA)) from environmental water samples. Separation of Fe₃O₄@PTh NPs from the aqueous solution was simply achieved by applying external magnetic field. Separation and determination of the extracted plasticizers was performed by gas chromatography–flame ionization detection (GC–FID). Several variables affecting the extraction efficiency of the analytes i.e., amount of NPs sorbent, salt concentration, extraction time, and desorption conditions were investigated and optimized. The best working conditions were as follows: amount of sorbent, 100 mg; NaCl concentration, 30% (w/v); sample volume, 45 mL; extraction time, 10 min; and 100 μL of ethyl acetate for desorption of the analytes within 2 min. Under optimized conditions, preconcentration factors for DBP, DEHP, and DOA were obtained as 86, 194, and 213, respectively. The calibration curves were linear (R² > 0.998) in the concentration range of 0.4–100 μg L⁻¹ for both DEHP and DOA and 0.7–100 μg L⁻¹ for DBP. The limits of detection (LODs) were obtained in the range of 0.2–0.4 μg L⁻¹. The intra-day relative standard deviations (RSDs%) based on four replicates were obtained in the range of 4.0–12.3%. The proposed procedure was applied to analysis of water samples including river water, bottled mineral water, and boiling water exposed to polyethylene container (after cooling) and recoveries between 85 and 99% and RSDs lower than 12.8% were obtained.     

The formation and physicochemical characterization of Al2O3-doped manganese ferrites

Mn/Fe mixed oxide solids doped with Al₂O₃ (0.32-1.27 wt.%) were prepared by impregnation of manganese nitrate with finely powdered ferric oxide, then treated with different amounts of aluminum nitrate. The obtained samples were calcined in air at 700-1000 °C for 6 h. The specific surface area (S_BET) and the catalytic activity of pure and doped precalcined at 700-1000 °C have been measured by using N₂ adsorption isotherms and CO oxidation by O₂. The structure and the phase changes were characterized by DTA and XRD techniques. The obtained results revealed that Mn₂O₃ interacted readily with Fe₂O₃ to produce well-crystallized manganese ferrite (MnFe₂O₄) at temperatures of 800 °C and above. The degree of propagation of this reaction increased by Al₂O₃-doping and also by increasing the heating temperature. The treatment with 1.27 wt.% Al₂O₃ followed by heating at 1000 °C resulted in complete conversion of Mn/Fe oxides into the corresponding ferrite phase. The catalytic activity and S_BET of pure and doped solids were found to decrease, by increasing both the calcination temperature and the amount of Al₂O₃ added, due to the enhanced formation of MnFe₂O₄ phase which is less reactive than the free oxides (Mn₂O₃ and Fe₂O₃). The activation energy of formation (ΔE) of MnFe₂O₄ was determined for pure and doped solids. The promotion effect of aluminum in formation of MnFe₂O₄ was attributed to an effective increase in the mobility of reacting cations.     

Hydrogen production from water decomposition by redox of Fe2O3 modified with single- or double-metal additives

Iron oxide modified with single- or double-metal additives (Cr, Ni, Zr, Ag, Mo, Mo-Cr, Mo-Ni, Mo-Zr and Mo-Ag), which can store and supply pure hydrogen by reduction of iron oxide with hydrogen and subsequent oxidation of reduced iron oxide with steam (Fe₃O₄ (initial Fe₂O₃)+4H₂↔3Fe+4H₂O), were prepared by impregnation. Effects of various metal additives in the samples on hydrogen production were investigated by the above-repeated redox. All the samples with Mo additive exhibited a better redox performance than those without Mo, and the Mo-Zr additive in iron oxide was the best effective one enhancing hydrogen production from water decomposition. For Fe₂O₃-Mo-Zr, the average H₂ production temperature could be significantly decreased to 276 °C, the average H₂ formation rate could be increased to 360.9-461.1 μmol min⁻¹ Fe-g⁻¹ at operating temperature of 300 °C and the average storage capacity was up to 4.73 wt% in four cycles, an amount close to the IEA target.     

SiO2 coated Fe3O4 magnetic nanoparticle dispersed multiwalled carbon nanotubes based amperometric glucose biosensor

A new type of amperometric glucose biosensor based on silicon dioxide coated magnetic nanoparticle decorated multiwalled carbon nanotubes (Fe₃O₄@SiO₂/MWNTs) on a glassy carbon electrode (GCE) has been developed. MWNTs have been synthesized by catalytic chemical vapour decomposition (CCVD) of acetylene over rare earth (RE) based AB₃ alloy hydride catalyst. The as-grown MWNTs have been purified and further functionlized. Functionalized MWNTs have been decorated with magnetic Fe₃O₄ nanoparticles which have been uniformly coated with biocompatible SiO₂ using a simple chemical reduction method. The characterization of magnetic nanoparticle modified MWNTs have been done by X-ray diffraction (XRD), Fourier transform infra red spectroscopy (FT-IR), scanning electron microscope (SEM), transmission electron microscope (TEM), vibrating sample magnetometer (VSM), energy dispersive X-ray analysis (EDX) and UV-vis spectroscopy. Amperometric biosensor has been fabricated by the deposition of glucose oxidase (GOD) over Nafion-solubilized Fe₃O₄@SiO₂/MWNTs electrode. The resultant bioelectrode retains its biocatalytic activity and offers fast and sensitive glucose quantification. The performance of the biosensor has been studied using cyclic voltammetry and amperometry and the results have been discussed. The fabricated glucose biosensor exhibits a linear response from 1 μM to 30 mM with an excellent detection limit of 800 nM indicating the potential applications in food industries.     

Barium alginate caged Fe3O4@C18 magnetic nanoparticles for the pre-concentration of polycyclic aromatic hydrocarbons and phthalate esters from environmental water samples

The hydrophobic octadecyl (C₁₈) functionalized Fe₃O₄ magnetic nanoparticles (Fe₃O₄@C₁₈) were caged into hydrophilic barium alginate (Ba²⁺-ALG) polymers to obtain a novel type of solid-phase extraction (SPE) sorbents, and the sorbents were applied to the pre-concentration of polycyclic aromatic hydrocarbons (PAHs) and phthalate esters (PAEs) pollutants from environmental water samples. The hydrophilicity of the Ba²⁺-ALG cage enhances the dispersibility of sorbents in water samples, and the superparamagnetism of the Fe₃O₄ core facilitates magnetic separation. With the magnetic SPE technique based on the Fe₃O₄@C₁₈@Ba²⁺-ALG sorbents, it requires only 30 min to extract trace levels of analytes from 500 mL water samples. After the eluate is condensed to 0.5 mL, concentration factors for both phenanthrene and di-n-propyl-phthalate are over 500, while for other analytes are about 1000. The recoveries of target compounds are independent of salinity and solution pH under testing conditions. Under optimized conditions, the detection limits for phenanthrene, pyrene, benzo[a]anthracene, and benzo[a]pyrene are 5, 5, 3, and 2 ng L⁻¹, and for di-n-propyl-phthalate, di-n-butyl-phthalate, di-cyclohexyl-phthalate, and di-n-octyl-phthalate are 36, 59, 19, and 36 ng L⁻¹, respectively. The spiked recoveries of several real water samples for PAHs and PAEs are in the range of 72-108% with relative standard deviations varying from 1% to 9%, showing good accuracy of the method. The advantages of the new SPE method include high extraction efficiency, short analysis time and convenient extraction procedure. To the best of our knowledge, it is unprecedented that hydrophilic Ba²⁺-ALG polymer caged Fe₃O₄@C₁₈ magnetic nanomaterial is used to extract organic pollutants from large volumes of water samples.     

In-tube magnetic solid phase microextraction of some fluoroquinolones based on the use of sodium dodecyl sulfate coated Fe3O4 nanoparticles packed tube

In-tube magnetic solid phase microextraction (in-tube MSPME) of fluoroquinolones from water and urine samples based on the use of sodium dodecyl sulfate (SDS) coated Fe₃O₄ nanoparticles packed tube has been reported. After the preparation of Fe₃O₄ nanoparticles (NPs) by a batch synthesis, these NPs were introduced into a stainless steel tube by a syringe and then a strong magnet was placed around the tube, so that the Fe₃O₄ NPs were remained in the tube and the tube was used in the in-tube SPME-HPLC/UV for the analysis of fluoroquinolones in water and urine samples. Plackett–Burman design was employed for screening the variables significantly affecting the extraction efficiency. Then, the significant factors were more investigated by Box–Behnken design. Calibration curves were linear (R² > 0.990) in the range of 0.1–1000 μg L⁻¹ for ciprofloxacin (CIP) and 0.5–500 μg L⁻¹ for enrofloxacin (ENR) and ofloxacin (OFL), respectively. LODs for all studied fluoroquinolones ranged from 0.01 to 0.05 μg L⁻¹. The main advantages of this method were rapid and easy automation and analysis, short extraction time, high sensitivity, possibility of fully sorbent collection after analysis, wide linear range and no need to organic solvents in extraction.     

Synthesis and characterization of poly(3-thiophene acetic acid)/Fe3O4 nanocomposite

Poly(3-thiophene acetic acid)/Fe₃O₄ nanocomposite is synthesized by the precipitation of Fe₃O₄ in the presence of poly(3-thiophene acetic acid) (P3TAA). Structural, surface, morphological, thermal properties and conductivity characterization/evaluation of the nanocomposite were performed by XRD, FT-IR, TEM, TGA, and conductivity measurements, respectively. The capping of P3TAA around Fe₃O₄ nanoparticles was confirmed by FT-IR spectroscopy, the interaction being via bridging oxygens of the carboxylate and the nanoparticle surface through bidentate binding. The crystallite and particle size were obtained as 9 ± 2 nm and 11 ± 1 nm from XRD line profile fitting and TEM image analysis, respectively, which reveal nearly single crystalline nature of Fe₃O₄ nanoparticles. Magnetization measurements reveal that P3TAA coated magnetite particles do not saturate at higher fields. There is no coercivity and remanence revealing superparamagnetic character. Magnetic particle size calculated from the theoretical fitting as 9.1 nm which coincides the values determined from TEM micrographs and XRD line profile fitting. The comparison to the TEM particle size reveals slightly modified magnetically dead nanoparticle surface.     

Synthesis, structure and magnetic properties of porous magnetic composite, based on MCM-41 molecular sieve with Fe3O4 nanoparticles

Porous magnetic composites were prepared by the synthesis of molecular sieve MCM-41 in the presence of Fe₃O₄ nanoparticles with average diameter of 15 nm. Nanoparticles were captured by porous silica matrix MCM-41, which resulted in their incorporation, as it was confirmed by TEM, SEM and X-ray diffraction. The materials possessed high surface area (392-666 m² g⁻¹), high pore volume (0.39-0.73 cm³ g⁻¹) along with high magnetic response (M_S up to 28.4 emu g⁻¹ at 300 K). Calcination of samples resulted in partial oxidation of Fe₃O₄ to α-Fe₂O₃. The influence of nanoparticles content on sorption and magnetic properties of the composites was shown. No hysteresis was found for the samples at 300 K; at 5 K, H_C was in the range 370-385 G for non-calcinated samples and 350-356 G for calcinated ones.     

Synthesis of Fe3O4\SiO2\Ag nanoparticles and its application in surface-enhanced Raman scattering

To obtain a recyclable surface-enhanced Raman scattering (SERS) material, we developed a composite of Fe₃O₄\SiO₂\Ag with core\shell\particles structure. The designed particles were synthesized via an ultrasonic route. The Raman scattering signal of Fe₃O₄ could be shielded by increasing the thickness of the SiO₂ layer to 60 nm. Dye rhodamine B (RB) was chosen as probe molecule to test the SERS effect of the synthesized Fe₃O₄\SiO₂\Ag particles. On the synthesized Fe₃O₄\SiO₂\Ag particles, the characteristic Raman bands of RB could be observed when the RB solution was diluted to 5 ppm (1×10⁻⁵ M). Furthermore, the synthesized particles could keep their efficiency till four cycles.     

Synthesis and characterization of Zn1−xNixFe2O4 spinels prepared by a citrate precursor

Nanocrystalline single-phase samples of Zn_1−xNi_xFe₂O₄ ferrites (0<x<1) have been obtained via a soft-chemistry method based on citrate-ethylene glycol precursors, at a relatively low temperature (650 °C). The influence of the nickel and zinc contents as well as that of heat treatments were investigated by means of X-ray powder diffraction, Brunauer-Emmett-Teller (BET) surface area, scanning electron microscopy (SEM) and Fourier Transform Infrared (FTIR) Spectroscopy. Higher Ni content increases the surface areas, the largest one (∼20 m²/g) being obtained for NiFe₂O₄ annealed at 650 °C for 15 h. For all compositions, the surface area decreases for prolonged annealing at 650 °C and for higher annealing temperatures. Those results were correlated to the particle size evolution; the smallest particles (∼50 nm) observed in the NiFe₂O₄ sample (650 °C, 15 h) steadily increase as Ni ions were replaced by Zn, reaching ∼100 nm in the ZnFe₂O₄ sample (650 °C, 15 h). For all the Zn_1−xNi_xFe₂O₄ samples and, whatever the heat treatments was, the FTIR spectra show two fundamental absorption bands in the range 650-400 cm⁻¹, characteristics of metal vibrations, without any superstructure stating for cation ordering. The highest ν₁-tetrahedral stretching, observed at ∼615 cm⁻¹ in NiFe₂O₄, shifts towards lower values with increasing Zn, whereas the ν₂-octahedral vibration, observed at 408 cm⁻¹ in NiFe₂O₄, moves towards higher wavenumbers, reaching 453 cm⁻¹ in ZnFe₂O₄.     

Synthesis and characterization of poly(vinyl phosphonic acid) (PVPA)-Fe3O4 nanocomposite

Poly(vinyl phosphonic acid) (PVPA)-Fe₃O₄ nanocomposite is synthesized by the precipitation of Fe₃O₄ in the presence of PVPA. Structural, surface, morphological, thermal properties and conductivity characterization/evaluation of the nanocomposite were performed by XRD, FT-IR, TEM, TGA and conductivity measurements respectively. The capping of PVPA around the Fe₃O₄ nanoparticles was confirmed by FT-IR spectroscopy, the interaction being via bridging oxygens of the phosphate and the nanoparticle surface. The crystallite and particle size were obtained as 6 ± 2 and 8.7 ± 0.1 nm from XRD line profile fitting and TEM image analysis respectively, which reveal nearly single crystalline nature of the Fe₃O₄ nanoparticles. Magnetic characterization of the bulk magnetite and (PVPA)-Fe₃O₄ nanocomposite reveals that both are in the superparamagnetic state at room temperature. The average magnetic domain size of the nanoparticles has been calculated using the Langevin function, which was fitted to the measured M-H hysteresis curves as 7.6 nm for the nanocomposite. In the nanocomposite, the reduction is due to the adsorption of PVPA onto the magnetite surface, which cancels some of the free spins at the surface causing a magnetically dead layer. Analysis of the conductivity and permittivity measurements revealed the coupling of ionic and polymer segmental motions and strong temperature dependency in the nanocomposite.     

High-pressure transitions in MgAl2O4 and a new high-pressure phase of Mg2Al2O5

Phase transitions in MgAl₂O₄ were examined at 21-27 GPa and 1400-2500 °C using a multianvil apparatus. A mixture of MgO and Al₂O₃ corundum that are high-pressure dissociation products of MgAl₂O₄ spinel combines into calcium-ferrite type MgAl₂O₄ at 26-27 GPa and 1400-2000 °C. At temperature above 2000 °C at pressure below 25.5 GPa, a mixture of Al₂O₃ corundum and a new phase with Mg₂Al₂O₅ composition is stable. The transition boundary between the two fields has a strongly negative pressure-temperature slope. Structure analysis and Rietveld refinement on the basis of the powder X-ray diffraction profile of the Mg₂Al₂O₅ phase indicated that the phase represented a new structure type with orthorhombic symmetry (Pbam), and the lattice parameters were determined as a=9.3710(6) Å, b=12.1952(6) Å, c=2.7916(2) Å, V=319.03(3) Å³, Z=4. The structure consists of edge-sharing and corner-sharing (Mg, Al)O₆ octahedra, and contains chains of edge-sharing octahedra running along the c-axis. A part of Mg atoms are accommodated in six-coordinated trigonal prism sites in tunnels surrounded by the chains of edge-sharing (Mg, Al)O₆ octahedra. The structure is related with that of ludwigite (Mg, Fe²⁺)₂(Fe³⁺, Al)(BO₃)O₂. The molar volume of the Mg₂Al₂O₅ phase is smaller by 0.18% than sum of molar volumes of 2MgO and Al₂O₃ corundum. High-pressure dissociation to the mixture of corundum-type phase and the phase with ludwigite-related structure has been found only in MgAl₂O₄ among various A²⁺B³⁺₂O₄ compounds.     

Nanocrystalline Ni0.6Zn0.4Fe2O4: A novel semiconducting material for ethanol detection

The structure and crystal phase of the nanocrystalline powders of Ni_1−xZn_xFe₂O₄ (0 ≤ x ≤ 0.5) mixed ferrite, synthesized by ethylene glycol mediated citrate sol-gel method, were characterized by X-ray diffraction and microstructure by transmission electron microscopy. Further studies by Fourier transform infrared spectroscopy were also conducted. Moreover, DC electrical properties of the prepared nanoparticles were studied by DC conductivity measurements. The response of prepared Ni_1−xZn_xFe₂O₄ mixed ferrites to different reducing gases (ethanol, hydrogen sulfide, ammonia, hydrogen and liquefied petroleum gas) was investigated. In particular, Ni_0.6Zn_0.4Fe₂O₄ composition exhibited high response to 100 ppm ethanol gas at 300 °C. Incorporation of palladium further improved the response, selectivity and response time of Ni_0.6Zn_0.4Fe₂O₄ to ethanol gas with the blue shift in the operating temperature by 25 °C.     

Enzyme mimics of spinel-type CoxNi1−xFe2O4 magnetic nanomaterial for eletroctrocatalytic oxidation of hydrogen peroxide

A series of spinel-type Co_xNi_1−xFe₂O₄ (x = 0, 0.2, 0.4, 0.5, 0.6, 0.8, 1.0) magnetic nanomaterials were solvothermally synthesized as enzyme mimics for the eletroctrocatalytic oxidation of H₂O₂. X-ray diffraction and scanning electron microscope were employed to characterize the composition, structure and morphology of the material. The electrochemical properties of spinel-type Co_xNi_1−xFe₂O₄ with different (Co/Ni) molar ratio toward H₂O₂ oxidation were investigated, and the results demonstrated that Co_0.5Ni_0.5Fe₂O₄ modified carbon paste electrode (Co_0.5Ni_0.5Fe₂O₄/CPE) possessed the best electrocatalytic activity for H₂O₂ oxidation. Under optimum conditions, the calibration curve for H₂O₂ determination on Co_0.5Ni_0.5Fe₂O₄/CPE was linear in a wide range of 1.0 × 10⁻⁸–1.0 × 10⁻³ M with low detection limit of 3.0 × 10⁻⁹ M (S/N = 3). The proposed Co_0.5Ni_0.5Fe₂O₄/CPE was also applied to the determination of H₂O₂ in commercial toothpastes with satisfactory results, indicating that Co_xNi_1−xFe₂O₄ is a promising hydrogen peroxidase mimics for the detection of H₂O₂.