不同氮源溶剂热合成N-TiO2纳米颗粒及其光催化降解气相苯（英文）

采用三种不同的氮源溶剂热合成了锐钛矿-板钛矿混晶的N-TiO2催化剂.采用X射线衍射、N2吸附-脱附、X射线光电子能谱和透射电子显微镜等手段对催化剂进行了表征.重点研究了不同氮源对催化剂的相组成、晶粒尺寸、微观结构以及比表面积的影响.采用紫外光降解气相苯测试了合成材料的催化活性.结果表明,以水合肼为氮源合成的N-TiO2表现出最优的光催化活性,其活性明显高于P25,且能够循环使用15次以上.采用气相色谱-质谱技术分析了光降解过程的中间产物,基于此提出了相应的降解机理.     

High photocatalytic degradation activity of polyethylene containing polyacrylamide grafted TiO2

A novel photocatalytic polyacrylamide grafted TiO₂ (PAM-g-TiO₂) nanocomposite was prepared and embedded into a low density polyethylene (LDPE) plastic. Photocatalytic degradation of the LDPE/PAM-g-TiO₂ composite film was carried out under ambient conditions under ultraviolet light irradiation. The properties of composite film were compared with those of the pure LDPE film by measuring the changes in weight loss, carbonyl index, molecular weight, tensile strength and elongation at break. PAM-g-TiO₂ embedded LDPE showed highly enhanced photocatalytic degradation. Irradiating the LDPE/PAM-g-TiO₂ composite film for 520 h under UV light reduced its weight by 39.85% and average molecular weight (M_w) by 94.60%, while that of pure LDPE film was only 1.03% and 69.59%, respectively. The addition of PAM-g-TiO₂ brought about the good dispersion of TiO₂ in LDPE matrix and improved the hydrophilicity of composite film, which were able to facilitate the degradation of LDPE. The photocatalytic degradation mechanism of the films is briefly discussed.     

Solid-phase photocatalytic degradation of polystyrene plastic with TiO2 as photocatalyst

Solid-phase photocatalytic degradation of polystyrene (PS) plastic with TiO₂ as photocatalyst was investigated in the ambient air under ultraviolet light irradiation. Higher weight loss rate, lower average molecular weight, increased carbonyl peak intensity, less volatile organics and more CO₂ emitted with irradiation in PS-TiO₂ composite sample compared to pure PS sample were observed. These facts indicated the higher photodegradation rate of PS-TiO₂ sample than that of PS sample, and emphasized the potential of the composite sample in bring about complete photodegradation of polystyrene plastic. It is implied that the degradation initially occurred over TiO₂ particles, followed by the diffusion reaction with the aid of reactive oxygen species generated on TiO₂ particle surface.     

Structural characterization and photocatalytic activity of hollow binary ZrO2/TiO2 oxide fibers

The formation of hollow binary ZrO₂/TiO₂ oxide fibers using mixed precursor solutions was achieved by activated carbon fibers templating technique combined with solvothermal process. The samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), N₂ adsorption, X-ray photoelectron spectroscopy (XPS), UV-vis, and infrared (IR) spectroscopy. The binary oxide system shows the anatase-type TiO₂ and tetragonal phase of ZrO₂, and the introduction of ZrO₂ notably inhibits the growth of TiO₂ nanocrystallites. Although calcined at 575 °C, all hollow ZrO₂/TiO₂ fibers exhibit higher surface areas (>113 m²/g) than pure TiO₂ hollow fibers. The Pyridine adsorption on ZrO₂/TiO₂ sample indicates the presence of stronger surface acid sites. Such properties bring about that the binary oxide system possesses higher efficiency and durable activity stability for photodegradation of gaseous ethylene and trichloromethane than P25 TiO₂. In addition, the macroscopic felt form for the resulting materials is more beneficial for practical applications than traditional catalysts forms.     

Photocatalytic activity of N-doped TiO2: photocatalytic synthesis of o-aminophenol at room temperature

The photocatalytic synthesis of o-aminophenol in methanol was investigated with N-doped TiO₂ nanoparticles under UV-light irradiation. The catalytic quantities of N-doped TiO₂ prepared by a simple modified sol–gel process with urea as nitrogen source rapidly reduced o-nitrophenol to the corresponding amine at room temperature.     

Synthesis of nanosized TiO2/SiO2 catalysts by the ultrasonic microemulsion method and their photocatalytic activity

Nanosized TiO₂/SiO₂ catalysts prepared by hydrolysis of titanium n-butoxide in microemulsion showed enhanced photocatalytic activity. In the presence of catalyst ME-2 and after 90 min irradiation by UV light, methylene blue was completely converted evidenced by the absence of its absorption band in the UV-Vis spectra. This catalyst demonstrated much better degradation ability than P-25 and naked TiO₂.     

TiO2 nanoparticles incorporated with CuInS2 clusters: preparation and photocatalytic activity for degradation of 4-nitrophenol

TiO₂ nanoparticles incorporated with CuInS₂ clusters were prepared in a solvothermal process and characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM), and energy-dispersion X-ray analysis (EDX). Compared with pure TiO₂ nanoparticles, the TiO₂ nanoparticles incorporated with CuInS₂ clusters display higher photocatalytic activity with 99.9% of degradation ratio of 4-nitrophenol after 2 h irradiation. In order to investigate the effect of the CuInS₂ clusters on the photocatalytic activity of TiO₂ nanoparticles, diffuse reflectance UV–Vis spectra (DRS), photoluminescence (PL) spectra, and photocurrent action spectra were measured. The results indicate that the enhanced photocatalytic activity is probably due to the interface between TiO₂ and CuInS₂ as a trap of the photogenerated electrons to decrease the recombination of electrons and holes.     

Preparation and photocatalytic degradability of TiO2/polyacrylamide composite

Based on the unique absorbent characters and three-dimensional network structure of polyacrylamide (PAM) superabsorbent polymer, a photocatalytic degradable TiO₂/PAM composite was synthesized by an aqueous solution polymerization method with N,N′-methylene bisacrylamide as crosslinker, potassium peroxydisulfate as initiator, acrylamide as monomer, and TiO₂ (P-25) as functional filler. The photocatalytic degradability of the composite was evaluated using methyl orange as photodegradation target, and the recovery and reproducibility of the composite was investigated. It was found that TiO₂/PAM composite had a good photocatalytic degradability, the composite also possessed a good reproducibility of photocatalytic degradability, which is possible to be used in practical process.     

Fabrication and photocatalytic activity of high-efficiency visible-light-responsive photocatalyst ZnTe/TiO2 nanotube arrays

A new ZnTe modified TiO₂ nanotube (NT) array catalyst was prepared by pulse potential electrodeposition of ZnTe nanoparticles (NPs) onto TiO₂ NT arrays, and its application for photocatalytic degradation of anthracene-9-carboxylic acid (9-AnCOOH) was investigated. The even distribution of ZnTe NPs was well-proportionately grown on the top surface of the TiO₂ NT while without clogging the tube entrances. Compared with the unmodified TiO₂ NT, the ZnTe modified TiO₂ NT (ZnTe/TiO₂ NT) showed significantly enhanced photocatalytic activity towards 9-AnCOOH under simulated solar light. After 70 min of irradiation, 9-AnCOOH was degraded with the removal ratio of 45% on the bare TiO₂ NT, much lower than 80%, 90%, and 100% on the ZnTe/TiO₂ NT with the ZnTe NPs prepared under the pulsed “on” potentials of −0.8, −1.0, and −2.0 V, respectively. The increased photodegradation efficiency mainly results from the improved photocurrent density as results of enhanced visible-light absorption and decreased hole-electron recombination due to the presence of narrow-band-gap p-type semiconductor ZnTe.     

Hydrothermal synthesis of mesostructured nanocrystalline TiO2 in an ionic liquid–water mixture and its photocatalytic performance

Anatase mesostructured TiO₂ nanocrystalline was prepared in a mixture of 1-butyl-3-methyl-imidazolium tetrafluoroborate (BMIM⁺BF₄⁻) ionic liquid and water by a low temperature hydrothermal method. The obtained materials were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM) and N₂ adsorption–desorption. The existence of BMIM⁺BF₄⁻ enhanced the polycondensation and crystallization rate, which encouraged the formation of anatase crystal. The TiO₂ particles were thermally very stable and thus resistant to anatase-rutile phase transformation during calcination at high temperatures. The anatase TiO₂ showed high photocatalytic activity in the degradation of p-chlorophenol than that of the commercially available TiO₂, Degussa P25. After 2 h reaction under the UV-irradiation of 250 W, the removing rate of p-chlorophenol was up to 96.3%.     

Synthesis, characterization of TiO2 nanotubes-supported MS (TiO2NTs@MS, M=Cd, Zn) and their photocatalytic activity

TiO₂ nanotubes-supported MS (TiO₂NTs@MS, M=Cd, Zn) are synthesized by a simple wet chemical method at room temperature. The products are characterized with transmission electron microscopy (TEM), X-ray diffraction (XRD), UV-vis absorption spectrum and photoluminescence (PL) spectrum. Their optical and morphological properties indicate the interaction between the TiO₂ nanotube and MS nanoparticle. The photocatalytic activities of the TiO₂NTs@MS are evaluated upon the oxidation of methyl orange under UV light illumination. The results reveal that the photocatalytic efficiency of the nanocomposites strongly depends on the specific interaction between MS and support.     

Synthesis and photocatalytic applications of Ag/TiO2-nanotubes

TiO₂- and Ag/TiO₂-nanotubes (NTs) were synthesized by hydrothermal methods and microwave-assisted preparation, respectively. Scanning electron microscopy, high resolution transmission electron microscopy, Brunauer-Emmett-Teller particle surface area measurement and X-ray diffraction were used to characterize the nanotubes. Rutile TiO₂-NTs with Na₂Ti₅O₁₁ crystallinity had a length range of 200-400 nm and diameters of 10-20 nm. TiO₂- and Ag/TiO₂-NTs with a 0.4% deposition of Ag had high surface areas of 270 and 169 m² g⁻¹, respectively. The evaluation of photocatalytic activity showed that Ag/TiO₂-NTs displayed higher photocatalytic activity than pure TiO₂-NTs and a 60.91% degradation of Rhodamine-B with 0.8% deposition of Ag species. Also 60% of Rhodamine-6G was physisorbed and 40% chemisorbed on the surface of TiO₂-NTs. In addition, the photocatalytic degradations of organochlorine pesticides taking α-hexachlorobenzene (BHC) and dicofol as typical examples, were compared using Ag/TiO₂-NTs, and found that their degradations rates were all higher than those obtained from commercial TiO₂.     

Visible-light responsive dye-modified TiO2 photocatalyst

A series of dye-modified TiO₂ photocatalysts were synthesized using dye Chrysoidine G (CG), tolylene-2,4-diisocyanate (TDI), and commercial TiO₂ (Degussa P25) as starting materials. TDI was used as a bridging molecule whose two -NCO groups reacted with Ti-OH of TiO₂ and -NH₂ groups of CG, respectively. As a result, special organic complexes were formed on the TiO₂ surface via stable π-conjugated chemical bonds between TiO₂ and dye molecules, confirmed by FT-IR, XPS, and UV-vis spectra. Due to the existence of π-conjugated surface organic complexes, the as-synthesized photocatalysts showed a great improvement in visible absorption (400-550 nm). Methylene blue, as a photodegradation target, was used to evaluate the photocatalytic performance, and the dye-modified TiO₂ exhibited much better activity under the visible light irradiation than bare TiO₂.     

A novel N-doped TiO2 with high visible light photocatalytic activity

A novel N-doped TiO₂ with high visible light photocatalytic activity was obtained by treating nanotube titanic acid (NTA) in NH₃ flow and investigated by means of XRD, TEM, ESR and XPS. The ESR results revealed that the visible light photocatalytic activity is originated from N-doping into TiO₂ with the forming of triplet paramagnetic species, the higher triplet paramagnetic species concentration, the better visible light photocatalytic behavior.     

Preparation and characterization of Zr doped TiO2 nanotube arrays on the titanium sheet and their enhanced photocatalytic activity

This paper described a new method for the preparation of Zr doped TiO₂ nanotube arrays by electrochemical method. TiO₂ nanotube arrays were prepared by anodization with titanium anode and platinum cathode. Afterwards, the formed TiO₂ nanotube arrays and Pt were used as cathode and anode, respectively, for preparation of Zr/TiO₂ nanotube arrays in the electrolyte of 0.1 M Zr(NO₃)₄ with different voltage and post-calcination process. The nanotube arrays were characterized by field-emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), X-ray photoelectron spectra (XPS) and UV-Vis diffusion reflection spectra (DRS). The photocatalytic activities of these nanotubes were investigated with Rhodamine B as the model pollutant and the results demonstrated that the photocatalytic efficiency of Zr doped TiO₂ nanotubes was much better than that of TiO₂ nanotubes under UV irradiation. Zr/TiO₂ nanotube arrays doped at 7 V and calcined at 600 °C (denoted as TiO₂-7 V-600) achieved the best photocatalytic efficiency and the most optimal doping ratio was 0.047 (Zr/Ti). TiO₂-7 V-600 could be reused for more than 20 times and maintained good photocatalytic activities.     

具有高可见光催化活性的Ti3+和碳共掺杂改性的TiO2光催化剂

以乙醇为碳源,采用操作简单的真空活化法一步实现对TiO₂的Ti³⁺与C的共掺杂改性,TiO₂用X衍线衍射、紫外-可见光谱、顺磁共振、X射线光电子能谱和红外光谱等手段表征了催化剂的结构、组成、光学性质. 结果表明, 经Ti³⁺与C共掺杂改性后的催化剂表现出高的可见光降解甲基橙活性. 复合在催化剂表面的石墨可以增强催化剂对可见光的响应范围,而Ti³⁺与氧缺陷形成的掺杂能级则可以提高光生电子的迁移效率. 实验表明,两者之间的协同作用促进了其可见光催化活性的提高.     

Preparation and visible light photocatalytic activity of Bi2O3/Bi2WO6 heterojunction photocatalysts

The Bi₂O₃/Bi₂WO₆ heterojunction photocatalysts were prepared by a two-step solvothermal process using Bi(NO₃)₃-ethylene glycol solution as Bi source. The catalysts were characterized by X-ray diffraction, scanning and transmission electron microscopy, X-ray photoelectron spectroscopy, and UV-vis diffuse reflection spectroscopy. The heterostructure catalysts are composed of Bi₂O₃ nanoparticles as modifier and 3D Bi₂WO₆ microspheres as substrate. Bi₂O₃ nanoparticles with diameters of about 10-15 nm are tightly grown on the lateral surface of the Bi₂WO₆ microspheres. The hierarchical Bi₂O₃/Bi₂WO₆ microspheres exhibit higher photocatalytic activity than the single phase Bi₂WO₆ or Bi₂O₃ for the degradation of rhodamine B under visible light illumination (λ>420 nm). The enhancement of the photocatalytic activity of the Bi₂O₃/Bi₂WO₆ heterojunction catalysts can be ascribed to their improved light absorption property and the reduced recombination of the photoexcited electrons and holes during the photocatalytic reaction. The effect of loading amount of Bi₂O₃ on the catalytic performance of the heterojunction catalysts was also investigated and the optimal content of Bi₂O₃ is 3 wt%. The Bi₂O₃/Bi₂WO₆ heterojunction photocatalysts are essentially stable during the photocatalytic process.     

A facile one-step preparation of hierarchically-structured TiO2 nanotube array photoanodes with enhanced photocatalytic activity

Hierarchically structured TiO₂ (HST) films composed of top porous nanoparticle layer and underneath nanotube array layer are obtained by an anodization method on fluorine doped tin oxide surfaces. Compared with the TiO₂ nanotube arrays photoanode on Ti substrate, the HST photoanode exhibits a higher photoelectrocatalytic activity towards the oxidation of water and organics (e.g., glucose).     

Preparation and photocatalytic activity of Sb2S3/Bi2S3 doped TiO2 from complex precursor via gel-hydrothermal treatment

Sb₂S₃/Bi₂S₃ doped TiO₂ were prepared with the coordination compounds [M(S₂CNEt)₃] (M=Sb, Bi; S₂CNEt=pyrrolidinedithiocarbamate) as precursors via gel-hydrothermal techniques. The doped TiO₂ were characterized by XRD, SEM, XPS and UV-vis diffuse reflectance means. The photocatalyst based on doped TiO₂ for photodecolorization of 4-nitrophenol (4-NP) was examined. The optimal Bi₂S₃/Sb₂S₃ content, pH and different doped techniques have been investigated. Photocatalytic tests reveal that M₂S₃ doped TiO₂ via the gel-hydrothermal route performs better photocatalytic activity for photodegradation reaction of 4-nitrophenol (4-NP).     

TiO2–carbon nanotube heterojunction arrays with a controllable thickness of TiO2 layer and their first application in photocatalysis

TiO₂–carbon nanotube (CNT) heterojunction arrays on Ti substrate were fabricated by a two-step thermal chemical vapor deposition (CVD) method. CNT arrays were first grown on Ti substrate vertically, and then a TiO₂ layer, whose thickness could be controlled by varying the deposition time, was deposited on CNTs. Measured by electrochemical impedance spectroscopy (EIS), the thickness of the TiO₂ layer could affect the photoresponse ability significantly. About 100 nm thickness of the TiO₂ layer proved to be best for efficient charge separation among the tested samples. The optimized TiO₂–CNT heterojunction arrays displayed apparently higher photoresponse capability than that of TiO₂ nanotube arrays which was confirmed by surface photovoltage (SPV) technique based on Kelvin probe and EIS. In the photocatalytic experiments, the kinetic constants of phenol degradation with TiO₂–CNT heterojunctions and TiO₂ nanotubes were 0.75 h⁻¹ (R² = 0.983) and 0.39 h⁻¹ (R² = 0.995), respectively. At the same time, 53.7% of total organic carbon (TOC) was removed with TiO₂–CNT heterojunctions, while the removal of TOC was only 16.7% with TiO₂ nanotubes. These results demonstrate the super capability of the TiO₂–CNT heterojunction arrays in photocatalysis with comparison to TiO₂-only nanomaterial.