Remote NADH imaging through an ordered array of electrochemiluminescent nanoapertures

In this report, we present an ordered array comprising thousands of nanoapertures for the electrochemiluminescent (ECL) detection of NADH. It was fabricated on the distal face of a coherent optical fiber bundle. Such a high-density array of nanoapertures combines optical, imaging and electrochemical properties. Indeed, each nanoaperture is surrounded by a gold nanoring, which acts as an electrode material. The behavior of the array was characterized by cyclic voltammetry and it shows excellent electrochemical performances. NADH is the analyte, which is measured in presence of Ru(bpy)3(2+). The ruthenium complex mediates the NADH oxidation and this coenzyme acts as a co-reactant in the ECL mechanism. ECL light is generated at the distal face of the array by each gold ring electrode. A fraction of this ECL light is collected by the corresponding nanoaperture, transmitted through the optical fiber bundle and finally imaged on the proximal face with a CCD camera. In this work, we show that NADH concentration is remotely detected by an oxidative-reductive ECL mechanism. We present also some preliminary results about the ECL process of NADH with Ru(bpy)3(2+). The ECL behavior of NADH on gold surface is reported. The influence of the applied potential on the collected light intensity was investigated. The variation of the ECL intensity measured through the nanoaperture array with NADH concentration is linear. Remote ECL detection of NADH is spatially resolved over a large area with a micrometer resolution through the array. Therefore, such array integrates several complementary functions: ECL light generation, collection, transmission and remote imaging in an array format.     

Opto-electrochemical nanosensor array for remote DNA detection

A high-density array of opto-electrochemical nanosensors is presented for remote DNA detection. It was fabricated by chemical etching of a coherent optical fibre bundle to produce a nanotip array. The surface of the etched bundle was sputter-coated with a thin ITO layer which was eventually insulated by an electrophoretic paint. The fabrication steps produced a high-density array of electrochemical nanosensors which retains the optical fibre bundle architecture and its imaging properties. A DNA probe was then immobilized on the nanosensor array surface in a polypyrrole film by electropolymerisation. After hybridisation with the complementary sequence, detection of the strepavidin-R-phycoerythrin label is performed by fluorescence imaging through the optical fibre bundle itself. Control experiments and regeneration steps have also been successfully demonstrated on this nanostructured opto-electrochemical platform.     

A simple,low-cost,remote fiber-optic micro volume fluorescence flowcell for capillary flow-injection analysis

A small volume flowcell for fluorescence detection in capillary flow injection (CFI) analysis has been created by using a low cost, commercially available fluidic device. Fluorescence detection is achieved using an optical fiber to deliver excitation light to the sample flowing through the device and another optical fiber to collect fluorescence emission. The flowcell is a standard fluidic cross with a swept volume of 721 nL. Optical fibers were oriented at right angles using standard sleeves and ferrules to set their position near the cross intersection. Multiple excitation sources were used including a low power UV laser and blue and UV light emitting diodes (LED). The full emission spectrum detection limits, using the laser, for fluorescein and bovine serum albumin (BSA) were 0.30 ppb and 2.1 x 10(-4)% (w/w), respectively. Two fluidic crosses were used in series for multi-wavelength fluorescence excitation using fiber-optically coupled LED.     

Photoactivated capture molecule immobilization in plasmonic nanoapertures in the ultraviolet

We demonstrate a photoactivated surface coupling scheme for achieving spatial overlap between biomolecules of interest and optical near field excitation. Using aluminium nanoapertures, we obtained increased coupling efficiency of biotinylated capture probe oligos to the photoactivated surface due to ~3× nanoaperture enhancement of UV light. We further validate DNA sensor functionality via the hybridization of Cy-5 labeled target oligos, with up to 8× fluorescence enhancement obtained from a commercial microarray scanner. This generic photoimmobilization strategy is an essential step to realizing miniaturized plasmon enhanced detection arrays by virtue of localizing capture molecules to the region of plasmonic enhancement.     

Application of charge-coupled device technology for measurement of laser light and fluorescence distribution in tumors for photodynamic therapy

Laser and fluorescence light distributions with applications for photodynamic therapy were measured in mouse tumors using a non-invasive electronic optical imaging system. The system consists of a liquid-nitrogen-cooled, charge-coupled-device (CCD) array camera under computer control with 576 x 384 detection elements having dimensions of 23 microns x 23 microns. The available dynamic range of the array is approx. 10(3), and the effective wavelength range is 400-1000 nm. An interstitially placed cylindrical diffusing optical fiber was used to provide tumor illumination. The light distribution pattern from the fiber was determined by immersing the cylindrical diffusing tip in a fluorescing solution and recording the emission image. Fluorescence imaging facilitates an accurate measurement of light intensity distribution while avoiding problems associated with the directional nature of other detection methods used with diffusing fibers. Radiation-induced fibrosarcoma tumors on C3H mice were grown to about 1 cm diameter for in vivo recording of light distribution from the tumor volume and for determination of effective light penetration distance at 18 wavelengths in the range 458-995 nm. Endogenous tumor fluorescence and Photofrin II fluorescence intensity were measured over the wavelength range 585-725 nm to investigate the possible application of CCD imaging technology for drug distribution measurements. Model experiments were begun to evaluate the relative importance of potential distortions of light distribution measurements using this approach.     

Cholera toxin subunit B detection in microfluidic devices

Fluorescence and electrochemical microfluidic biosensors were developed for the detection of cholera toxin subunit B (CTB) as a model analyte. The microfluidic devices were made from polydimethylsiloxane (PDMS) using soft lithography from silicon templates. The polymer channels were sealed with a glass plate and packaged in a polymethylmethacrylate housing that provided leakproof sealing and a connection to a syringe pump. In the electrochemical format, an interdigitated ultramicroelectrode array (IDUA) was patterned onto the glass slide using photolithography, gold evaporation and lift-off processes. For CTB recognition, CTB-specific antibodies were immobilized onto superparamagnetic beads and ganglioside GM₁ was incorporated into liposomes. The fluorescence dye sulforhodamine B (SRB) and the electroactive compounds potassium hexacyanoferrate (II)/hexacyanoferrate (III) were used as detection markers that were encapsulated inside the liposomes for the fluorescence and electrochemical detection formats, respectively. Initial optimization experiments were carried out by applying the superparamagnetic beads in microtiter plate assays and SRB liposomes before they were transferred to the microfluidic systems. The limits of detection (LoD) of both assay formats for CTB were found to be 6.6 and 1.0 ng mL⁻¹ for the fluorescence and electrochemical formats, respectively. Changing the detection system was very easy, requiring only the synthesis of different marker-encapsulating liposomes, as well as the exchange of the detection unit. It was found that, in addition to a lower LoD, the electrochemical format assay showed advantages over the fluorescence format in terms of flexibility and reliability of signal recording.     

Column radial homogeneity in high-performance liquid chromatography

The radial distribution of analyte molecules within an elution band in HPLC was determined by local, on-column, fluorescence detection at the column outlet. Several optical fiber assemblies were implanted in the exit frit at different points over the column cross-section and the fluorescence of a laser-dye analyte was measured. The individual elements of a diode array were used as independent detectors. The distribution of the mobile phase velocity across the column was measured for a number of standard size analytical HPLC columns of different efficiencies, operated at different mobile phase linear velocities. The dependence of the column efficiency on these profiles is discussed.     

Smartphone based bacterial detection using biofunctionalized fluorescent nanoparticles

We are describing immunochromatographic test strips with smart phone-based fluorescence readout. They are intended for use in the detection of the foodborne bacterial pathogens Salmonella spp. and Escherichia coli O157. Silica nanoparticles (SiNPs) were doped with FITC and Ru(bpy), conjugated to the respective antibodies, and then used in a conventional lateral flow immunoassay (LFIA). Fluorescence was recorded by inserting the nitrocellulose strip into a smart phone-based fluorimeter consisting of a light weight (40 g) optical module containing an LED light source, a fluorescence filter set and a lens attached to the integrated camera of the cell phone in order to acquire high-resolution fluorescence images. The images were analysed by exploiting the quick image processing application of the cell phone and enable the detection of pathogens within few minutes. This LFIA is capable of detecting pathogens in concentrations as low as 10⁵ cfu mL⁻¹ directly from test samples without pre-enrichment. The detection is one order of magnitude better compared to gold nanoparticle-based LFIAs under similar condition. The successful combination of fluorescent nanoparticle-based pathogen detection by LFIAs with a smart phone-based detection platform has resulted in a portable device with improved diagnosis features and having potential application in diagnostics and environmental monitoring.

The successful combination of fluorescent nanoparticle-based pathogen detection by lateral flow immunoassay with a smart phone-based detection platform has resulted in a portable device that enables rapid and reliable bacterial detection holding large potential in diagnostics and environmental monitoring

     

Design and characterization of a fiber optic-based fluorimeter

The design and preliminary charaterization of a novel fiber optic-based fluorimeter are reported. It includes a white light source, optical fibers for light transmission and an intensified photodiode array for detection. A bifurcated sensing configuration is used to transmit excitation and emission radiation to and from the analyte solution. Detection limits in the nanomolar range are reported for several test compounds.     

Fibre coupled micro-light emitting diode array light source with integrated band-pass filter for fluorescence detection in miniaturised analytical systems

In this work, a new type of miniaturized fibre-coupled solid-state light source is demonstrated as an excitation source for fluorescence detection in capillary electrophoresis. It is based on a parabolically shaped micro-light emitting diode (μ-LED) array with a custom band-pass optical interference filter (IF) deposited at the back of the LED substrate. The GaN μ-LED array consisted of 270 individual μ-LED elements with a peak emission at 470 nm, each about 14 μm in diameter and operated as a single unit. Light was extracted through the transparent substrate material, and coupled to an optical fibre (OF, 400 μm in diameter, numerical aperture NA = 0.37), to form an integrated μ-LED-IF-OF light source component. This packaged μ-LED-IF-OF light source emitted approximately 225 μW of optical power at a bias current of 20 mA. The bandpass IF filter was designed to reduce undesirable LED light emissions in the wavelength range above 490 nm. Devices with and without IF were compared in terms of the optical power output, spectral characteristics as well as LOD values. While the IF consisted of only 7.5 pairs (15 layers) of SiO₂/HfO₂ layers, it resulted in an improvement of the baseline noise as well as the detection limit measured using fluorescein as test analyte, both by approximately one order of magnitude, with a LOD of 1 × 10⁻⁸ mol L⁻¹ obtained under optimised conditions. The μ-LED-IF-OF light source was then demonstrated for use in capillary electrophoresis with fluorimetric detection. The limits of detection obtained by this device were compared to those obtained with a commercial fibre coupled LED device.     

Polyester microchannel chip for electrophoresis - incorporation of a blue LED as light source

A blue-light-emitting diode was incorporated as a fluorescence-excitation light source into a polyester microchannel chip fabricated by in situ polymerization. Placing the light-emitting facet of the diode close to the microchannel obviated any need for an additional optical arrangement. Fluorescence from the sample was transmitted by an optical fiber incorporated into the microchip perpendicular to the LED. FITC labeled amino acids were separated in the presence of 5 mM SDS by using the microchip and were detected by LED-induced fluorescence.     

Electropolymerization as a versatile route for immobilizing biological species onto surfaces

Biosensors based on electronic conducting polymers appear particularly well suited to the requirements of modern biological analysis—multiparametric assays, high information density, and miniaturization. We describe a new methodology for the preparation of addressed DNA matrices. The process includes an electrochemically directed copolymerization of pyrrole and oligonucleotides bearing on their 5′ end a pyrrole moiety. The resulting polymer film deposited on the addressed electrode consists of pyrrole chains bearing covalently linked oligonucleotides (ODN). An oligonucleotide array was constructed on a silicon device bearing a matrix of 48 addressable 50 × 50 μm gold microelectrodes. This technology was successfully applied to the genotyping of hepatitis C virus in blood samples. Fluorescence detection results show good sensitivity and a high degree of spatial resolution. In addition, gravimetric studies carried out by the quartz crystal microbalance technique provide quantitative data on the amount of surface-immobilized species. In the case of ODN, it allows discrimination between hybridization and nonspecific adsorption. The need for versatile processes for the immobilization of biological species on surfaces led us to extend our methodology. A biotinylated surface was obtained by coelectropolymerization of pyrrole and biotin-pyrrole monomers. The efficiency for recognition (and consequently immobilization) of R-phycoerythrin-avidin was demonstrated by fluorescence detection. Copolymerization of decreasing ratios of pyrrole-biotin over pyrrole allowed us to obtain a decreasing scale of fluorescence.     

Optical fiber light-emitting diode-induced fluorescence detection for capillary electrophoresis

A highly sensitive optical fiber light-emitting diode (LED)-induced fluorescence detector for CE has been constructed and evaluated. In this detector, a violet or blue LED was used as the excitation source and an optical fiber with 40 microm OD was used to transmit the excitation light. The upper end of the fiber was inserted into the separation capillary and was situated right at the detection window. Fluorescence emission was collected by a 40 x microscope objective, focused on a spatial filter, and passed through a cutoff filter before reaching the photomultiplier tube. Output signals were recorded and processed with a computer using in-house written software. The present CE/fluorescence detector deploys a simple and inexpensive optical system that requires only an LED as the light source. Its utility was successfully demonstrated by the separation and determination of amino acids (AAs) labeled with naphthalene-2,3-dicarboxaldehyde (NDA) and FITC. Low detection limits were obtained ranging from 17 to 23 nM for NDA-tagged AAs and 8 to 12 nM for FITC-labeled AAs (S/N=3). By virtue of such valuable features as low cost, convenience, and miniaturization, the presented detection scheme was proven to be attractive for sensitive fluorescence detection in CE.     

In-column fiber-optic laser-induced fluorescence detection for CE

A highly sensitive in-column fiber-optic LIF detector for CE has been constructed and evaluated. In this detection system, a 457-nm diode-pumped solid-state blue laser was used as the excitation light source and an optical fiber (40 mum od) was used to transmit the excitation light. One end of the optical fiber was inserted into the separation capillary and was in situ positioned at the detection window. The other end of the fiber was protruded from the capillary to capture the excitation light beam from the blue laser. Fluorescence emission was collected by a 40 x microscope objective, focused on a spatial filter, and passed through a yellow color filter before reaching the photomultiplier tube. The present CE-fluorescence detection is a simple and compact optical system. It reduces the laser scattering effect from the capillary and fiber as compared to the conventional LIF detection for CE. Its utility was successfully demonstrated by the separation and determination of D-penicillamine labeled with naphthalene-2,3-dicarboxaldehyde. The detection limit was 0.8 nM (S/N = 3). The present detection scheme has been proven to be attractive for sensitive fluorescence detection for CE.     

Direct immobilization of Fab' in nanocapillaries for manipulating mass-limited samples

Interfacing nanoscale elements into a microfluidic device enables a new range of fluidic manipulations. Nanocapillary array membranes (NCAMs), consisting of thin (5 microm < d < 20 microm) membranes containing arrays of nanometer diameter (10 nm < a < 500 nm) pores, are a convenient method of interfacing vertically separated microchannels in microfluidic devices that allow the external control of analyte transport between microfluidic channels. To add functionality to these nanopores beyond simple fluid transport, here we incorporate an antibody-based molecular recognition element onto the pore surface that allows selective capture, purification, and release of specific analytes from a mixture. The pores are fabricated by electroless plating of gold into the nanopores of an NCAM (Au-NCAM). An antibody is then immobilized on the Au-NCAM via gold-thiol chemistry as a thiolated fragment of antigen-binding (Fab') prepared by direct digestion of the antibody followed by reduction of the disulfide linkage on the hinge region. The successful immobilization and biological activity of the resultant Fab' through this protocol is verified on planar gold by fluorescence microscopy, scanning electron microscopy, and atomic force microscopy. Selective capture and release of human insulin is verified using matrix-assisted laser desorption/ionization time-of-flight mass spectrometry. The relative mass spectral peak intensities for insulin versus nonantigenic peptides increase more than 20-fold after passing through the Fab'-Au-NCAM relative to the control Au-NCAM. The affinity-tagged Au-NCAM can be incorporated into microfluidic devices to allow the concentration, capture, and characterization of analytes in complex mixtures with high specificity.     

On-chip multi-electrochemical sensor array platform for simultaneous screening of nitric oxide and peroxynitrite

In this work we report on the design, microfabrication and analytical performances of a new electrochemical sensor array (ESA) which allows for the first time the simultaneous amperometric detection of nitric oxide (NO) and peroxynitrite (ONOO(-)), two biologically relevant molecules. The on-chip device includes individually addressable sets of gold ultramicroelectrodes (UMEs) of 50 μm diameter, Ag/AgCl reference electrode and gold counter electrode. The electrodes are separated into two groups; each has one reference electrode, one counter electrode and 110 UMEs specifically tailored to detect a specific analyte. The ESA is incorporated on a custom interface with a cell culture well and spring contact pins that can be easily interconnected to an external multichannel potentiostat. Each UME of the network dedicated to the detection of NO is electrochemically modified by electrodepositing thin layers of poly(eugenol) and poly(phenol). The detection of NO is performed amperometrically at 0.8 V vs. Ag/AgCl in phosphate buffer solution (PBS, pH = 7.4) and other buffers adapted to biological cell culture, using a NO-donor. The network of UMEs dedicated to the detection of ONOO(-) is used without further chemical modification of the surface and the uncoated gold electrodes operate at -0.1 V vs. Ag/AgCl to detect the reduction of ONOOH in PBS. The selectivity issue of both sensors against major biologically relevant interfering analytes is examined. Simultaneous detection of NO and ONOO(-) in PBS is also achieved.     

Smartphone based bacterial detection using biofunctionalized fluorescent nanoparticles

We are describing immunochromatographic test strips with smart phone-based fluorescence readout. They are intended for use in the detection of the foodborne bacterial pathogens Salmonella spp. and Escherichia coli O157. Silica nanoparticles (SiNPs) were doped with FITC and Ru(bpy), conjugated to the respective antibodies, and then used in a conventional lateral flow immunoassay (LFIA). Fluorescence was recorded by inserting the nitrocellulose strip into a smart phone-based fluorimeter consisting of a light weight (40 g) optical module containing an LED light source, a fluorescence filter set and a lens attached to the integrated camera of the cell phone in order to acquire high-resolution fluorescence images. The images were analysed by exploiting the quick image processing application of the cell phone and enable the detection of pathogens within few minutes. This LFIA is capable of detecting pathogens in concentrations as low as 10⁵ cfu mL^?1 directly from test samples without pre-enrichment. The detection is one order of magnitude better compared to gold nanoparticle-based LFIAs under similar condition. The successful combination of fluorescent nanoparticle-based pathogen detection by LFIAs with a smart phone-based detection platform has resulted in a portable device with improved diagnosis features and having potential application in diagnostics and environmental monitoring. Figure

The successful combination of fluorescent nanoparticle-based pathogen detection by lateral flow immunoassay with a smart phone-based detection platform has resulted in a portable device that enables rapid and reliable bacterial detection holding large potential in diagnostics and environmental monitoring     

发光二极管诱导荧光用于毛细管电泳检测

利用发光二极管作为激发光源，组装了用于毛细管电泳的荧光检测器。光纤用于传输荧光信号；光纤端面修饰成球形使耦合效率比平面端光纤提高了50．8％；光阑、光纤及毛细管检测池之间的光学校准简单、便捷。荧光素染料用于评价该体系性能，得到了fmol的质量检出限。     

Analytical applications of a carbon nanotubes composite modified with copper microparticles as detector in flow systems

A simple microchip electrophoresis-laser-induced fluorescence device was constructed and used for separation and determination of catecholamines. On the fabricated glass chip, an extra optical fiber insertion channel, which was perpendicular and extremely close to the separation channel, was directly integrated by nothing operations more than design features on the photomask. The utilization of optical fiber to transmit the excitation light and the integration fiber channel make the fluorescence detection system simple and disposable. For electrophoresis, optimization of separation conditions was investigated for reaching high separation efficiency and sensitivity. A separation efficiency as high as 10⁶ theoretical plate numbers could be obtained for the analytes.     

Cover Picture

The cover picture shows an etched and metallized optical fiber tip for chemical analysis on the nanometer scale using near-field optical microscopy and spectroscopy. The background shows an image of nanospheres embedded in a polymer matrix that were visualized via fluorescence. Further details are given in the review by R. Zenobi and V. Deckert on pages 1746-1756.