固相微萃取-气相色谱-质谱联用分析环境水样中痕量有机磷农药

研究了固相微萃取(SPME) 气相色谱 质谱联用(GC MS)同时测定环境水样中二嗪农、甲基对硫磷、对硫磷和水胺硫磷4种有机磷农药(OPPs)的分析方法。选择聚丙烯酸酯(PA)萃取纤维,对SPME的条件如萃取时间、萃取溶液的pH值和离子强度、解吸温度、解吸时间和GC MS的条件进行了优化。对二嗪农和水胺硫磷方法线性范围为0.001～10μg L,对甲基对硫磷和对硫磷方法线性范围为0.001～100μg L。二嗪农、甲基对硫磷、对硫磷、水胺硫磷的检出限分别为0.015,0.020,0.013和0.039μg L。分析加标自来水、矿泉水和湖水样品,回收率在89.0%～102%之间,RSD在2.1%～14.1%之间。适合于环境水样中痕量OPPs的快速分析。     

Determination of oxadiazon residues by headspace solid-phase microextraction and gas chromatography-mass spectrometry

A method for the determination of trace amounts of the herbicide oxadiazon was developed using headspace solid-phase microextraction (HS-SPME), gas chromatography-mass spectrometry (GC-MS) and selected ion monitoring. It was applied to determine oxadiazon in ground water, agricultural soil, must, wine and human urine samples. To determine oxadiazon in liquid samples, a response surface methodology generated with a Doehlert design was applied to optimize the HS-SPME conditions using a 100 microm polydimethylsiloxane fibre. For the analysis of soil samples, they were mixed with water and the SPME fibre suspended in the headspace above the slurry. Ground water, human urine and must show linear concentration range of application of 0.5-50 ng ml(-1)' with detection limits < or =0.02 ng ml(-1). HS-SPME-GC-MS analysis yielded good reproducibility (RSD values between 6.5 and 13.5%). The method validation was completed with spiked matrix samples. The developed analytical procedure is solvent free, cost effective and fast.     

Development of a headspace solid-phase microextraction/gas chromatography-mass spectrometry method for determination of organophosphorus pesticide residues in cow milk

In the past few years, organophosphorus compounds become one of the most widely used classes of pesticides due to their acute toxicity against a wide variety of pests. In this work, a method based on solid-phase microextraction in mode headspace (HS-SPME) coupled to gas chromatography-mass spectrometry (GC-MS) was developed and optimized through multivariate factorial design to determine residues of organophosphorus pesticides in cow's milk. Different parameters of the method were evaluated, such as fiber type, temperature, extraction and desorption times, sample volume, effect of salt addition and stirring velocities. The evaluated pesticides were dichlorvos, sulfotep, demeton-S, dimpylate, disulfoton, parathion, methyl parathion, fenitrothion, chlorpyrifos and ethion. The best results were obtained using polydimethylsiloxane/divinylbenzene fiber and headspace mode at 90 °C for 45 min, along with stirring at 600 rpm and desorption for 5 min at 250 °C. Under the optimized conditions, the proposed methodology was able to determine all of the pesticides with variation coefficients between 6.1% and 29.5%. Detection and quantification limits ranged from 2.16 to 10.85 μg L^− 1 and from 6.5 to 32.9 μg L^− 1, respectively. To evaluate residues of these pesticides in milk, cows were exposed to the pesticides of interest and milk was collected after 24 h. The developed method was able to detect trace amounts of these pesticides in the collected milk samples.     

Comparison of microextraction procedures to determine pesticides in oranges by liquid chromatography-mass spectrometry

A liquid chromatographic–mass spectrometric method has been developed for the determination of bitertanol, carbendazim, fenthion, flusilazole, hexythiazox, imidacloprid, methidathion, methiocarb, pyriproxyfen and trichlorfon. Two procedures, based on stir bar sorptive extraction (SBSE) and matrix solid-phase dispersion (MSPD), have been evaluated for the extraction of these compounds in oranges. Their respective advantages and disadvantages are also discussed. The recoveries obtained by MSPD ranged from 47 to 96% and the relative standard deviations (RSDs) ranged from 1 to 15%, whereas with the SBSE method the recoveries were between 8 and 84% and the RSDs between 4 and 16%. Although, the limits of quantitation of most compounds are much better (0.001–0.05 mg kg⁻¹) by SBSE, it is not suitable to determine some polar pesticides as carbendazim, imidacloprid and trichlorfon. Results obtained by both methods were compared, in terms of sensitivity and selectivity, with a classical ethyl acetate extraction method, and the three methods were applied to analyze real samples. As MSPD is easier to perform, faster than the organic solvent extraction, and shows equal accuracy and resolution, its application for analyzing pesticides in oranges is recommended.     

Application of solid-phase microextraction for the determination of organophosphorus pesticides in textiles by gas chromatography with mass spectrometry

A method based on solid-phase microextraction (SPME) and gas chromatography with mass spectrometry (GC/MS) for the determination of 18 organophosphorus pesticides (OPPs) in textiles is described. Commercially available SPME fibers, 100 μm PDMS and 85 μm PA, were compared and 85 μm PA exhibited better performance to the OPPs. Various parameters affecting SPME, including extraction and desorption time, extraction temperature, salinity and pH, were studied. The optimized conditions were: 35 min extraction at 25 °C, 5% NaSO₄ content, pH 7.0, and 3.5 min desorption in GC injector port at 250 °C. The linear ranges of the SPME-GC/MS method were 0.1-500 μg L⁻¹ for most of the OPPs. The limits of detection (LODs) ranged from 0.01 μg L⁻¹ (for bromophos-ethyl) to 55 μg L⁻¹ (for azinphos-methyl) and the RSDs were between 0.66% and 9.22%. The optimized method was then used to analyze 18 OPPs in textile sample, and the determined recoveries were ranged from 76.7% to 126.8%. Moreover, the distribution coefficients of the OPPs between 85 μm PA fiber and simulative sweat solution (K_pa/s) were determined. The determined K_pa/s of the OPPs correlated well with their octanol-water partition coefficients (r = 0.764 and 0.678) and water solubility (r = −0.892 and −0.863).     

Application of headspace solid-phase microextraction followed by gas chromatography-mass spectrometry to determine short-chain alkane monocarboxylic acids in aqueous samples

In this study, a procedure was developed to determine short-chain alkane monocarboxylic acids (SCMAs) in aqueous samples using headspace solid-phase microextraction (HS-SPME) followed by gas chromatography (GC) coupled with mass spectrometry (MS). A Stabilwax-DA capillary column (30 m × 0.32-mm inner diameter, 0.50-μm film thickness) was used for GC separation and a 60-μm poly(ethylene glycol) fiber was used to isolate SCMAs from water and introduce them into the gas chromatograph. Parameters of HS-SPME, analyte desorption, and GC-MS analysis were selected and an analytical procedure was proposed. Limits of quantitation were on the order of about 0.2 mg L^-1. As an example of the application of the procedure, SCAMs were determined in municipal wastewater at different steps of treatment.     

Determination of residues of 446 pesticides in fruits and vegetables by three-cartridge solid-phase extraction-gas chromatography-mass spectrometry and liquid chromatography-tandem mass spectrometry

A method was developed for determination of residues of 446 pesticides in fruits and vegetables through the use of cleanup by a 3-cartridge solid-phase extraction-gas chromatography/ mass spectrometry (GC/MS) and liquid chromatography/tandem mass spectrometry (LC/MS/MS). Fruit and vegetable samples (20 g) were extracted with 40 mL acetonitrile, salted out, and centrifuged. Half of the supernatant was passed into an Envi-18 cartridge, eluted with acetonitrile, and cleaned up with Envi-Carb and aminopropyl Sep-Pak cartridges in series after concentration of the eluates. Pesticides were eluted with acetonitrile-toluene (3 + 1, v/v), and eluates were concentrated to 0.5 mL and then added into internal standards after solvent exchange with 2 mL hexane and used for determination of 383 pesticides by GC/MS. The other half of the supernatant was concentrated to 1 mL and cleaned up with Envi-Carb and aminopropyl Sep-Pak cartridges in series. Pesticides were eluted with acetonitrile-toluene (3 + 1, v/v), and the eluates were concentrated to 0.5 mL, dried with nitrogen gas, diluted to 1.0 mL with acetonitrile-water (3 + 2, v/v), and used for determination of 63 pesticides by LC/MS/MS. The limit of detection for the method was 0.2-600 ng/g depending on the individual pesticide. In the method, fortification recovery tests at high, medium, and low levels were conducted on 6 varieties of fruits and vegetables, i.e., apples, oranges, grapes, cabbage, tomatoes, and celery, with average recoveries falling within the range of 55.0-133.8% for 446 pesticides, among which average recoveries between 60.0-120.0% accounted for 99% of the results. The relative standard deviation was between 2.1-39.1%, of which a relative standard deviation of 2.1-25.0% made up 96% of the results. Experiments proved that the method was applicable for determination of residues of 446 pesticides in fruit and vegetables.     

Determination of organophosphorus pesticides in honeybees after solid-phase microextraction

The solvation parameter model has been applied to the characterization of micellar electrokinetic chromatographic (MEKC) systems with mixtures of lithium dodecyl sulfate and lithium perfluorooctanesulfonate as surfactant. The variation in MEKC surfactant composition results in changes in the coefficients of the correlation equation, which in turns leads to information on solute-solvent and solute-micelle interactions. Lithium perfluorooctanesulfonate is more dipolar and hydrogen bond acidic but less polarizable and hydrogen bond basic than lithium dodecyl sulfate. Therefore mixtures of lithium dodecyl sulfate and lithium perfluorooctanesulfonate cover a very wide range of polarity and hydrogen bond properties, which in turn results in important selectivity changes for analytes with different solute properties.     

Determination of fipronil by solid-phase microextraction and gas chromatography-mass spectrometry.

A method for the determination of trace amounts of the insecticide fipronil was developed using solid-phase microextraction-gas chromatography-mass spectrometry and selected ion monitoring. Fipronil was extracted with a fused-silica fiber coated with 85 microm polyacrylate. The effects of pH, ionic strength, sample volume, extraction and desorption times as well as the extraction temperature were studied. Lindane was used as an internal standard. The linear concentration range of application was 0.3-100 ng ml(-1) of fipronil, with a relative standard deviation of 9.5% (for a level of 50 ng ml(-1)) and a detection limit of 0.08 ng ml(-1). The method was applied to check the eventual existence of fipronil above this limit in water and soil samples from Granada (Spain) as well as in human urine samples. The method validation was completed with spiked matrix samples. The method can be applied as a monitoring tool for water, soil and urine, in the investigation of environmental and occupational exposure to fipronil.     

Determination of triazines in soil leachates by solid-phase microextraction coupled to gas chromatography-mass spectrometry

A solid-phase microextraction-gas chromatography-mass spectrometry (SPME-GC-MS) method was developed for the evaluation of the leachability order of selected triazines (propazine, terbuthylazine, sebuthylazine, ametryn, prometryn and terbutryn) in soil/sediment samples (organic carbon content ranging from 0.19 to 0.42%), analysing fractions collected from a soil packed microcolumn elution experiments. The procedure is fast, simple, highly sensitive and solvent free. SPME-GC-MS was also employed for the quantitative determination of triazines in the soil leachate, since the method showed good recovery yield. Detection limits were always better than 1 ng ml(-1). The method was tested on a contaminated landfill top soil. Prometryn and ametryn were identified through their MS spectra and then quantified. Terbuthylazine was used to assess recovery. Results compared well with those obtained by solvent extraction followed by HPLC-UV detection.     

Determination of polycyclic aromatic hydrocarbons in sediment using solid-phase microextraction with gas chromatography-mass spectrometry

Manual solid-phase microextraction (SPME) coupled with gas chromatography-mass spectrometry (GC-MS) is applied for the determination of polycyclic aromatic hydrocarbons (PAHs) from natural matrix through a distilled water medium. Seven of the 16 PAH standards (naphthalene, acenaphthene, fluorene, anthracene, fluoranthene, pyrene, benzo[a]anthracene) are spiked on a marine muddy sediment. The samples, containing PAHs in the range of 10-20 ppm, are then aged at room temperature more than 10 days before analysis. The influence of the matrix, SPME adsorption time, pH, salt content, and SPME adsorption temperature are investigated. The reproducibility of the technique is less than 13% (RDS) for the first 6 considered PAHs and 28% (RDS) for benzo(a)anthracene with a fiber containing a 100-micron poly dimethylsiloxane coating. Linearity extended in the range of 5-50 picograms for PAHs direct injection, 5-70 picograms for PAHs in water, and 1-170 picograms for PAHs in sediment. The detection limit is estimated less than 1 microgram/kg of dry sample for the first 6 considered PAHs in sediment and 1.5 micrograms/kg of dry sample for benzo(a)anthracene using the selected ion monitoring mode in GC-MS. The recoveries of the considered PAHs are evaluated.     

Determination of isophorone in food samples by solid-phase microextraction coupled with gas chromatography-mass spectrometry

A simple and sensitive method for the determination of isophorone in food samples was developed by headspace solid-phase microextraction (HS-SPME) coupled with gas chromatography-mass spectrometry (GC-MS). Isophorone was separated within 10 min by GC-MS using a DB-1 capillary column and detected with selective ion monitoring mode. The HS-SPME using a polydimethylsiloxane/divinylbenzene (PDMS/DVB) fiber provided effective sample enrichment, and was carried out by fiber exposition at 60 degrees C for 45 min. The extracted isophorone was easily desorbed by fiber exposition in the injection port of a capillary GC-MS system, and carryover was not observed. Using this method, the calibration curve of isophorone was linear in the range 20-1000 pg/mL, with a correlation coefficient 0.9996 (n = 18), and the detection limit (S/N = 3) was 0.5 pg/mL. The HS-SPME/GC-MS method showed 25,000-fold higher sensitivity than the direct injection method (1 microL injection). The within-day and between-day precisions (relative standard deviations) at the concentration of 1 ng/mL isophorone were 3.9% and 6.1% (n=5), respectively. This method was successfully applied to the analysis of food samples without interference peaks. The recoveries of isophorone spiked into food sample were above 84% for a 50 or 500 pg/mL spiking concentration. The analytical results of the contents of isophorone in various food samples were presented.     

Determination of pesticides in soil by liquid-phase microextraction and gas chromatography-mass spectrometry

Trace amounts of pesticides in soil were determined by liquid-phase microextraction (LPME) coupled to gas chromatography-mass spectrometry (GC-MS). The technique involved the use of a small amount (3 microl) of organic solvent impregnated in a hollow fiber membrane, which was attached to the needle of a conventional GC syringe. The organic solvent was repeatedly discharged into and withdrawn from the porous polypropylene hollow fiber by a syringe pump, with the pesticides being extracted from a 4 ml aqueous soil sample into the organic solvent within the hollow fiber. Aspects of the developed procedure such as organic solvent selection, extraction time, movement pattern of plunger, concentrations of humic acid and salt, and the proportion of organic solvent in the soil sample, were optimized. Limits of detection (LOD) were between 0.05 and 0.1 microg/g with GC-MS analysis under selected-ion monitoring (SIM). Also, this method provided good precision ranging from 6 to 13%; the relative standard deviations were lower than 10% for most target pesticides (at spiked levels of 0.5 microg/g in aqueous soil sample). Finally, the results were compared to those achieved using solid-phase microextraction (SPME). The results demonstrated that LPME was a fast (within 4 min) and accurate method to determine trace amounts of pesticides in soil.     

Determination of polydimethylsiloxane-seawater distribution coefficients for polychlorinated biphenyls and chlorinated pesticides by solid-phase microextraction and gas chromatography-mass spectrometry

Applications of solid-phase microextraction (SPME) in the measurement of very hydrophobic organic compounds (VHOCs) are limited, partly due to the difficulty of calibrating SPME fibers for VHOCs. This study used a static SPME strategy with a large sample volume (1.6 L) and a five-point calibration procedure to determine the distribution coefficients for a large suite of polychlorinated biphenyls (PCBs) and chlorinated pesticides between a polydimethylsiloxane (PDMS) phase (100 microm thickness) coated on a glass fiber and seawater. An extraction time of 12 days was deemed adequate for equilibrium calibration from kinetic experiments. Two groups of randomly selected fibers divided into three batches (up to nine fibers in each batch) were processed separately with two gas chromatography-mass spectrometry (GC-MS) systems. Matrix effects arising from losses of the analytes to glass container walls and stirring bars were corrected. Relative standard deviations within the same batch were generally smaller than those for the entire group. Furthermore, KfVf (Kf and Vf are the distribution coefficient of an analyte between the polymer-coated fiber and aqueous phase and the fiber volume, respectively) values determined with two GC-MS systems were statistically different. These results indicate the calibrated KfVf values were less affected by the random selection of SPME fibers than by other experimental conditions, and therefore average KfVf values may be used for the same type of commercially available SPME fibers. The relative accuracy of our calibration method was similar to that of a previous study [P. Mayer. W.H.J. Vaes, J.L.M. Hermens, Anal. Chem. 72 (2000) 459] employing different coating thickness and calibration procedure. The present study also obtained a bell-shaped relationship between log Kf and log Kow (octanol-water partition coefficient) for PCB congeners with the maximum log Kf corresponding to log Kow approximately 6.5. This bell-shaped relationship was attributed mainly to steric effects arising from the interplay between the PDMS thickness and molecular sizes of the target analytes.     

Advanced method using microwaves and solid-phase microextraction coupled with gas chromatography-mass spectrometry for the determination of pyrethroid residues in strawberries

A microwave-assisted desorption method was developed and coupled with solid-phase microextraction and GC-MS for the analysis of pyrethroid residues in strawberries. In the first step, pyrethroid analytes were desorbed from the whole fruits in an aqueous acetonitrile solution at 50% under microwave assistance, so preventing these compounds to be captured with strong matrix effects by endogenous constituents. Then, the 100 microm poly(dimethylsiloxane)-coated fibre was exposed for 30 min in the obtained extracting solution. Calibration curves, realised from blank strawberries spiked at different concentrations with standards, showed a linear range between 1 microg/kg and 250 microg/kg with r2 > 0.992 and variation coefficients below 15%. Limits of detection and quantitation were found lower than 14 microg/kg and 40 microg/kg, respectively. Observed analysis results by using this method and relative to field incurred strawberry samples were also compared to those obtained by two accredited trading laboratories using traditional methods.     

On-line determination of organophosphorus pesticides in water by solid-phase microextraction and gas chromatography with thermionic-selective detection

This paper describes the extraction of 49 organophosphorus pesti-cides (OPPs) from water samples using solid-phase microextraction (SPME). Three fibers, including a 15-μm XAD-coated fiber, a 85-μm polyacrylate-coated fiber, and a 30-μm polydimethylsilox-ane-coated fiber (PDMS), were evaluated here. The effects of stirring and the addition of NaCl to the sample were examined for the polyacrylate-coated fiber. The precision of the technique was examined for all three fibers and the extraction kinetics were investigated using the XAD- and polyacrylate-coated fibers. With some exceptions, the XAD- and polyacrylate-coated fibers performed better than the PDMS-coated fiber. The superiority of the XAD-nd polyacrylate-coated fiber. The superiority of the XAD- and polyacrylate-coated fibers over the PDMS-coated fibers can be attribuibuted to the aromatic functionalities of the XAD and the polar functionalities in the polyacrylate. The relatively high percent RSDs indicate that the SPME technique needs to be further refined before it can be used for anything other than screening. A more effective form of agitation than mechanical stirring may be neccessary to reduce variability and achieve a faster equilibrium between the sample and the SPME fiber.     

Multi-residue determination of organophosphorus and organochlorine pesticides in environmental samples using solid-phase extraction with cigarette filter followed by gas chromatography-mass spectrometry

A solid‐phase extraction (SPE) method was developed to extract 14 pesticides simultaneously from environment samples using cigarette filter as the sorbent before gas chromatography‐mass spectrometry (GC‐MS) analysis. Parameters influencing the extraction efficiency, such as the sample loading flow rate, eluent and elution volume, were optimized. The optimum sample loading rate was 3 mL/min, and the retained compounds were eluted with 6 mL of eluent at 1 mL/min under vacuum. Good linearity was obtained for all the 14 pesticides (r²>0.99) from 0.1 to 20 μg/L for water and from 2 to 400 μg/kg for soil samples. The detection limits (signal‐to‐noise=3) of the proposed method ranged from 0.01 to 0.20 μg/L for water samples and from 0.42 to 6.95 μg/kg for soil samples. The developed method was successfully applied for determination of the analytes in real environmental samples, and the mean recoveries ranged from 76.4 to 103.7% for water samples and from 79.9 to 105.3% for soil samples with the precisions (relative standard deviation) between 2.0 and 13.6%.     

Determination of tebufenpyrad and oxadiazon by solid-phase microextraction and gas chromatography-mass spectrometry

Summary A method for determination of trace amounts of the pesticides tebufenpyrad and oxadiazon, previous solid-phase microextraction (SPME), was developed using gas chromatographymass spectrometry and selected ion monitoring (GC-MS; SIM). Both pesticides were extracted with a fused silica fiber coated with 100 μm polydimethylsiloxane. The effects of pH ionic strength, sample volume, extraction and desorption times as well as extraction temperature were studied. The linear concentration range of application was 0.5–250 ng mL⁻¹ for both compounds, with a detection limit of 0.06 ng mL⁻¹ for tebufenpyrad and 0.02 ng mL⁻¹ for oxadiazon. SPME-GC-MS analysis yielded good reproducibility (RSD between 7.5–10.1%). It was used to check the eventual existence of tebufenpyrad and oxadiazon above this limit in water and soil samples from Granada (Spain) as well as in human urine samples. The method validation was completed with spiked matrix samples. It can be applied as a monitoring tool for water, soil and urine in the investigation of environmental and occupational exposure to tebufenpyrad and oxadiazon.     

Determination of organophosphorus pesticides in soil by headspace solid-phase microextraction

Headspace solid-phase microextraction (SPME) has been developed for the analysis of common organophosphorus pesticides in soil. Factors such as adsorption-time, sampling temperature and matrix modification by addition of water were carefully considered to optimize the extraction efficiency. This technique could achieve limits of detection of 143 ng/g for Malathion and Parathion, and 28.6 ng/g for Phorate, Diazinon and Disulfoton in humic soil when the extracted sample was analyzed by gas chromatography-flame ionization detector (GC-FID). Lower limits of detection of 28.6 ng/g for Malathion and Parathion, and 14.3 ng/g for Phorate, Diazinon and Disulfoton can be achieved by analyzing the extracted sample with gas chromatography/mass spectrometric detector (GC/MS). As the extraction efficiency was generally better when analyzing sandy soil, the limits of detection are envisaged to be even better for such a matrix. The technique was found to be reliable with good precision of about 6.5% RSD for the sandy soil and about 15% for the humic material. The poorer precision of extraction from the humic material is probably related to the poorer homogeneity of this material. The linearity of extraction was good with linear calibration in the range of 0.143 to 28.6 μg/g. Finally, headspace SPME was compared to aqueous extraction of soil followed by SPME (LE-SPME). The recoveries obtained by headspace SPME were comparable to those from liquid-liquid extraction of soil followed by SPME. However, the analysis of headspace SPME has less background interference. Perhaps, the greatest advantage of this technique is its non-destructive nature so that it is possible to perform further laboratory analysis of the samples after headspace SPME has been carried out. Received: 13 July 1998 / Revised: 10 November 1998 / Accepted: 17 November 1998     

Determination of organophosphorus pesticides in soil by headspace solid-phase microextraction

Headspace solid-phase microextraction (SPME) has been developed for the analysis of common organophosphorus pesticides in soil. Factors such as adsorption-time, sampling temperature and matrix modification by addition of water were carefully considered to optimize the extraction efficiency. This technique could achieve limits of detection of 143 ng/g for Malathion and Parathion, and 28.6 ng/g for Phorate, Diazinon and Disulfoton in humic soil when the extracted sample was analyzed by gas chromatography-flame ionization detector (GC-FID). Lower limits of detection of 28.6 ng/g for Malathion and Parathion, and 14.3 ng/g for Phorate, Diazinon and Disulfoton can be achieved by analyzing the extracted sample with gas chromatography/mass spectrometric detector (GC/MS). As the extraction efficiency was generally better when analyzing sandy soil, the limits of detection are envisaged to be even better for such a matrix. The technique was found to be reliable with good precision of about 6.5% RSD for the sandy soil and about 15% for the humic material. The poorer precision of extraction from the humic material is probably related to the poorer homogeneity of this material. The linearity of extraction was good with linear calibration in the range of 0.143 to 28.6 μg/g. Finally, headspace SPME was compared to aqueous extraction of soil followed by SPME (LE-SPME). The recoveries obtained by headspace SPME were comparable to those from liquid-liquid extraction of soil followed by SPME. However, the analysis of headspace SPME has less background interference. Perhaps, the greatest advantage of this technique is its non-destructive nature so that it is possible to perform further laboratory analysis of the samples after headspace SPME has been carried out.