TiO_2分级结构/Ag_3PO_4复合材料的可见光催化性能

制备了具有分级结构的海胆状TiO2纳米材料,并通过原位沉积法将可见光响应的Ag3PO4纳米颗粒沉积到TiO2的纳米分级结构上,合成了具有高效稳定可见光催化性能的系列TiO2分级结构/Ag3PO4复合材料,对比测试了系列材料对罗丹明B(RhB)的光催化降解性能.结果表明,TiO2分级结构/Ag3PO4复合材料光催化性能明显高于纯相的Ag3PO4光催化剂,同时也明显优于TiO2(P25)/Ag3PO4复合光催化剂,其中分级结构TiO2与Ag3PO4摩尔比为1∶1的复合材料具有最强的光催化性能,在可见光照射6min内可实现RhB的完全脱色.分析结果表明,与纳米颗粒TiO2相比,具有海胆状纳米结构的TiO2可为Ag3PO4的负载提供更多的担载位点,增加TiO2和Ag3PO4的接触面积,进而提升Ag3PO4光激发产生的光生电子-空穴的分离效率.同时在光降解过程中,Ag3PO4表面存在的少量Ag+会逐渐还原成单质Ag0,通过Ag0的等离子体共振效应,可增加对光子的吸收转换能力,从而进一步提高该复合材料光催化降解染料的性能.     

TiO_2/Ag_2NCN复合光催化剂的制备与可见光催化性能

利用银盐与单氰胺水溶液的沉淀反应,通过共混不同质量分数的纳米TiO2粒子制备了TiO2/Ag2NCN复合光催化剂.使用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、傅里叶变换红外(FTIR)光谱仪和紫外-可见(UV-Vis)吸收光谱仪对复合光催化剂的结构进行了表征.结果表明,锐钛矿相TiO2纳米颗粒沉积在Ag2NCN表面形成异质结构,二者间以弱的物理作用力相结合.TiO2的掺杂使得复合颗粒的UV-Vis吸收光谱发生红移,带隙变窄.以亚甲基蓝(MB)为光催化降解对象,研究了TiO2/Ag2NCN复合颗粒的可见光催化活性.结果表明,与单一Ag2NCN相比,复合颗粒表现出增强的光催化性能.对TiO2/Ag2NCN复合颗粒的光催化反应动力学过程及光催化机理进行了探讨.     

溶剂热法制备Ag/TiO_2纳米材料及其光催化性能

以乙醇为溶剂,钛酸四丁酯为前驱体,用溶剂热法制备了Ag表面修饰的负载型纳米二氧化钛光催化剂.利用X射线衍射(XRD)、N2吸附-脱附(BET)、透射电子显微镜(TEM)、X射线光电子能谱(XPS)、紫外-可见(UV-Vis)光谱等技术对其进行了系统的表征,以亚甲基蓝(MB)溶液的脱色降解为模型反应,考察了不同Ag含量样品的光催化性能.结果表明:用溶剂热法制备的样品中TiO2皆为锐钛矿相,金属Ag颗粒沉积在TiO2表面,粒径为2nm左右,比表面积较溶胶凝胶法制备的样品大大增加,最高可达151.44m2·g-1;UV-Vis光谱和光催化实验表明:Ag修饰使TiO2对光的吸收能力大大增强,吸收带边红移至可见光区,亚甲基蓝在该复合材料上的光催化降解反应遵循一级反应动力学模型;溶剂热法制备样品的光催化性能明显好于溶胶凝胶法制备的样品,在紫外光和可见光下,Ag摩尔分数为5%的样品表现出最佳的光催化活性.     

应用射线束制备可见光响应的TiO2薄膜

 由溶胶-凝胶法制备了TiO2薄膜. 为了改善TiO2对光的利用效率,采用过渡金属离子(V+和Cr+)注入和电子束辐照沉积贵金属纳米颗粒(Ag和Pt)两种射线束技术对TiO2薄膜进行改性. 紫外-可见光谱表明,两种射线束技术改性的TiO2薄膜的吸收光谱都发生了红移,说明这两种方法都是拓展TiO2吸收光谱的有效手段. 通过光催化降解甲基橙实验,比较了两种方法对TiO2可见光光催化能力的拓展情况,结果表明,两种方法均可显著提高TiO2在可见光作用下的光催化活性.     

Ag修饰的Fe_3O_4/TiO_2复合磁性纳米纤维的制备及光催化性能

通过静电纺丝法制备了含有Fe3O4纳米粒子的TiO2纳米纤维,采用水热法对该纤维表面进行纳米Ag修饰,制备出具有较强磁性和较好光催化性能的复合纤维.采用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和紫外-可见光谱(UV-Vis)等对样品的结构和形貌进行表征,并以罗丹明B(Rh B)水溶液降解为模型反应,考察样品在紫外光照射下的光催化性能.结果表明,所制备的TiO2为锐钛矿结构,Fe3O4纳米粒子均匀分布在TiO2纤维中,Ag纳米颗粒比较均匀地分散在磁性TiO2纤维表面.经过纳米Ag修饰后,材料的光吸收能力大为增强,吸收带红移并扩展到可见光区.在紫外光照射40 min后,合成样品对Rh B的降解率达到99.5%.此外,Fe3O4纳米粒子的存在使该材料具有较强的磁性,可通过外加磁场将其分离回收.     

微波载银对纳米二氧化钛相变及光催化性能的增效作用

用微波法制备系列载Ag纳米TiO2,发现微波载Ag对纳米TiO2的相变和光催化活性具有增效作用。采用X-射线粉末衍射(XRD),透射电镜(TEM),X-射线光电子能谱仪(XPS),激光Raman光谱及漫反射光谱(DRS)方法对比研究纳米TiO2与载Ag纳米TiO2的性质。结果表明,所制得载Ag纳米TiO2是以锐钛矿为主相的混晶,平均粒径约为10 nm,负载Ag促进纳米TiO2中锐钛矿相转化金红石相相变,减小纳米晶尺寸,并使纳米TiO2光响应范围向可见光区移动 6 nm。在低浓度范围,微波法能均匀地将Ag负载于纳米TiO2表面,并以Ag0/Ag+的形式存在,抑制光生电子与光生空穴复合,大大地提高了纳米TiO2光催化活性。在近紫外-可见光照射下,载Ag量为0.05 mol %的纳米TiO2对罗丹明B的光催化降解效果最好。     

g-C3N4/Ag/TiO2复合材料的构筑及其光催化性能（英文）

以合成的g-C3N4纳米片和Ag/TiO2空心微球为原料,采用机械搅拌的方法构筑了g-C3N4/Ag/TiO2三元复合光催化剂。采用X射线衍射(XRD)、傅里叶变换红外光谱(FT-IR)、扫描电镜(SEM)、X射线光电子能谱(XPS)、紫外-可见光漫反射(UV-Vis DRS)和光致发光光谱(PL)对g-C3N4/Ag/TiO2进行了表征。研究表明,g-C3N4/Ag/TiO2是由Ag/TiO2微球和g-C3N4纳米片复合而成的。与TiO2相比,其可见光响应范围延长,光生载流子的分离速率加快。在室温下,用降解罗丹明B的反应考察了g-C3N4/Ag/TiO2的可见光催化活性。研究表明,光照180 min时,g-C3N4(0.5%)/Ag/TiO2显示了最高的光催化活性(91.9%),分别是TiO2和Ag/TiO2的7.5和1.8倍。光催化活性的提高与合理的异质结构建和Ag的导电性能有关。     

高效Ag@AgBr等离子体光催化剂的制备及可见光活性研究

采用水热法和光致还原法制备了具有等离子体共振效应的Ag@AgBr可见光催化剂,利用XRD,SEM,EDX,DRS和XPS等手段对产物的结构和性能进行表征,并研究了催化剂在可见光下对罗丹明B(RhB)的光催化降解性能,考察了催化剂的循环使用及捕获剂对Ag@AgBr光催化性能的影响.结果表明:贵金属Ag纳米粒子的表面等离子体共振效应可显著增强Ag@AgBr对可见光的吸收;催化剂对罗丹明B具有较高的可见光降解活性和稳定性,在可见光下照射90 min,对罗丹明B的降解率达95%以上,光催化剂循环使用5次仍具有良好的光催化降解活性;淬灭实验表明在Ag@AgBr降解罗丹明B过程中,吸附在催化剂表面的h+、·OH、O2·-是主要的活性物种.     

ZnFe2O4/TiO2纳米管阵列电极的制备及光电催化降解苯酚的研究

采用阳极氧化法和电沉积法制备出具有可见光响应的ZnFe2O4/TiO2纳米管阵列电极.用环境扫描电子显微镜(ESEM)、X-射线衍射(XRD)和透射电子显微镜(TEM)对制备的ZnFe2O4/TiO2纳米管阵列电极的表面形貌和结构进行了表征.结果表明,该方法成功地将ZnFe2O4纳米颗粒均匀分散在TiO2纳米管中,分布在管口处的较少.同时,详细讨论了反应物浓度、沉积时间、循环次数、沉积电压对ZnFe2O4/TiO2纳米管阵列电极性能的影响.通过在可见光下降解苯酚评价了复合电极的光催化活性,实验结果表明:由于ZnFe2O4和TiO2之间的协同效应,复合电极的光响应范围扩展到了可见光区域,光电催化活性提高1.5～2倍.     

负载银纳米粒子的多酸银盐复合材料的可见光催化性能研究

通过固相研磨法,选取具有不同中心杂原子的Keggin型多酸(H_3PW_(12)O_(40)、H_4SiW_(12)O_(40)、K_5BW_(12)O_(40))固体与硝酸银固体反应,制备得到了系列低溶解度的多酸银盐前驱体(Ag_nPOM).再以这类多酸银盐为基质,通过紫外光照,使其中部分抗衡阳离子Ag~+原位还原生成金属Ag纳米粒子,进而可获得一系列具有不同Ag纳米粒子负载量的Ag_x~0/Ag_n~IPOM复合材料.固体漫反射光谱表明,Ag纳米粒子的表面等离子体(plasmon)共振吸收导致复合材料在可见光区域的吸收明显增加.这类复合材料在可见光照射下对光催化降解甲基橙和光还原Cr(Ⅵ)展现出高效、稳定的催化活性.随着阴离子所带电荷的增加,Ag纳米粒子的负载量明显增加,可见光吸收增强,因此光催化活性越高.Ag_x~0/Ag_5~IBW_(12)O_(40)展现最佳的光催化活性.     

Photocatalytic property of surface-modified TiO<Subscript>2</Subscript> nanobelts under visible light irradiation

A novel plasmonic photocatalyst, i.e., acid-etched TiO₂ nanobelts attached with Ag/AgI nanoparticles (NPs) was prepared by deposition–precipitation-photoreduction method. Such surface-modified nanobelts had larger area than the normal one. Ag NPs were formed from AgI by photo-reduction under Xenon lamp irradiation. X-ray diffraction, scanning electron microscopy analysis, UV–Vis diffuse reflectance spectra and fluorescence spectra were used to characterize the structure and optical properties of the sample. The obtained sample exhibited strong photodegradation of methyl orange (MO) under visible light irradiation, which were attributed to both the surface plasmon resonance of Ag NPs and the visible light actived AgI. The photodegradation was accomplished by the transfer of photoexcited electrons from the Ag NPs to the acid-etched TiO₂ nanobelts. After four cycles of photodegradation the photocatalyst was still stable. This novel photocatalyst had a high potential application in wastewater-treatment and biomedical engineering.     

Preparation of Ag3PO4/TiO2(B) Heterojunction Nanobelt with Extended Light Response and Enhanced Photocatalytic Performance

Photocatalytic degradation, as an emerging method to control environmental pollution, is considered one of the most promising environmental purification technologies. As Tibet is a region with some of the strongest solar radiation in China and even in the world, it is extremely rich in solar energy resources, which is ideal for applying photocatalytic technology to its ecological environment protection and governance. In this study, Na₂Ti₃O₇ nanobelts were prepared via a hydrothermal method and converted to TiO₂∙xH₂O ion exchange, which was followed by high-temperature calcination to prepare TiO₂(B) nanobelts (“B” in TiO₂(B) means “Bronze phase”). A simple in situ method was used to generate Ag₃PO₄ particles on the surface of the TiO₂ nanobelts to construct a Ag₃PO₄/TiO₂(B) heterojunction composite photocatalyst. By generating Ag₃PO₄ nanoparticles on the surface of the TiO₂(B) nanobelts to construct heterojunctions, the light absorption range of the photocatalyst was successfully extended from UV (ultraviolet) to the visible region. Furthermore, the recombination of photogenerated electron–hole pairs in the catalyst was inhibited by the construction of the heterojunctions, thus greatly enhancing its light quantum efficiency. Therefore, the prepared Ag₃PO₄/TiO₂(B) heterojunction composite photocatalyst greatly outperformed the TiO₂(B) nanobelt in terms of photocatalytic degradation.     

A new acidic Ti sol impregnated kaolin photocatalyst: synthesis, characterization and visible light photocatalytic performance

In this study, a photocatalyst with visible light photocatalytic activity was obtained using raw materials, including commercial TiO₂, sulfuric acid, and calcined kaolin (CK). The photocatalyst was prepared via a dissolving/impregnating process, in which acidic Ti sol was obtained by initially dissolving TiO₂ particles in sulfuric acid, and then using the sol as impregnant for the CK. The prepared photocatalyst had wide spectral region and narrow band gap. In addition, the impregnation can create acid sites on the obtained composite surface and consequently improve the activity. A series of tests was performed to characterize the properties of the prepared samples. The visible light photocatalytic degradation of methyl orange (MO) in an aqueous solution was used as a probe reaction to evaluate the photocatalytic activities of the obtained samples. Under visible light irradiation, approximately 80 % of MO (with initial concentration of 20 mg/m³) was degraded in 3 h on the photocatalyst prepared by impregnating CK in acidic Ti sol, which was obtained using approximately 60 % H₂SO₄ solution followed by calcination at 400 °C. The acidity of the photocatalyst is the main factor that affects the catalytic activity of the photocatalytic degradation of MO.     

Preparation and characterization of sulfur-modified mesoporous titania photocatalyst

Sulfur-modified mesoporous titania (S-MTiO₂) was investigated as a potential photocatalyst under visible light. The photocatalyst was prepared by template method using thiourea and tetrabutyl titanate (Ti(OC₄H₉)₄) as precursors and Pluronic P123 as template. The photoabsorbance of as-prepared photocatalyst was measured by UV-vis absorption spectroscopy, which confirmed the extension of absorption into the visible region. The microstructure of S-MTiO₂ was characterized using X-ray diffraction (XRD) and N₂ adsorption-desorption measurements. The micro crystal of the S-doped photocatalyst consisted of anatase phase and no significant influence on the nature of crystal formation. X-ray photoelectron spectroscopy (XPS) measurements indicated the presence of C in the prepared photocatalyst in addition to S. The photo-catalytic performance was studied by photodegradation methyl orange (MO) in water under visible light irradiation. The calcination temperature and the doping content influenced the photoactivity.     

WO3纳米片：基于有机-无机杂化前驱物的制备及光催化性能

以商业三氧化钨粉末做为钨源,通过合成WO_x-EDA（EDA=乙二胺）有机-无机杂化纳米带为前驱物,再加盐酸酸化,迅速得到中间产物正交型钨酸单晶纳米片。再在空气气氛下,将中间产物在管式炉中煅烧2h,最终得到单斜型三氧化钨单晶纳米片。一系列对比实验的结果表明,在由杂化纳米带转变成钨酸纳米片时,反应温度、反应时间、酸化浓度等实验参数对产物的结构和形貌有着很大的影响。通过计算,制得的三氧化钨纳米片带隙为2.48eV。对比于商业三氧化钨粉末,三氧化钨纳米片在可见光降解罗丹明B（RhB）中表现出更优越的性能。     

花球状Bi2S3/BiOI复合光催化剂在空气中净化甲醛的应用

以硫代乙酰胺为硫源,采用水热阴离子转移法,制备由纳米片组装的花球状Bi₂S₃/BiOI复合光催化剂。以气相甲醛作为模型污染物,在检测舱中考察了复合催化剂对甲醛的净化作用。结果表明,具有异质结结构的Bi₂S₃/BiOI复合光催化剂具有较高的光催化活性,能在可见光下净化空气中的甲醛,并且具有良好的循环使用稳定性。     

花球状Bi2S3/BiOI复合光催化剂去除空气中甲醛的应用

以硫代乙酰胺为硫源,采用水热阴离子转移法,制备由纳米片组装的花球状Bi₂S₃/BiOI复合光催化剂。以气相甲醛作为模型污染物,在检测舱中考察了复合催化剂对甲醛的去除作用。结果表明,具有异质结结构的Bi₂S₃/BiOI复合光催化剂具有较高的光催化活性,能在可见光下去除空气中的甲醛,并且具有良好的循环使用稳定性。     

多孔超薄g-C3N4纳米片负载Pt复合材料的制备及其光催化性能

以三聚氰胺为前驱体,通过热氧化刻蚀法制备多孔超薄g-C₃N₄纳米片（CNHS）,将其与氯铂酸钾溶液混合后采用原位光化学还原法成功制备了CNHS负载Pt光催化剂（Pt-CNHS）。使用粉末X射线衍射、场发射扫描电子显微镜、X射线光电子能谱、透射电子显微镜、紫外可见漫反射光谱和N₂吸附-脱附测试等技术对所制备样品的结构、形貌、光吸收特性、光电化学性能和比表面积等进行系统分析。并以气相甲苯为目标降解物,研究其光催化性能。结果表明,相对于体相g-C₃N₄（CNB）和CNHS,Pt的引入可以有效增强催化剂对可见光的吸收能力、响应范围及载流子分离效率。与纯g-C₃N₄和CNHS相比,Pt-CNHS在紫外和可见光照射下均表现出更高的光催化降解气相甲苯的活性。此外,也对Pt-CNHS光催化剂在可见光照射下降解气相甲苯的反应历程做了初步研究。     

High ethanol sensitivity of Palladium/TiO2 nanobelt surface heterostructures dominated by enlarged surface area and nano-Schottky junctions

TiO₂ nanobelts were prepared by the hydrothermal growth method. The surface of the nanobelts was coarsened by selective acid corrosion and functionalized with Pd catalyst particles. Three nanobelt samples (TiO₂ nanobelts, surface-coarsened TiO₂ nanobelts and Pd nanoparticle/TiO₂ nanobelt surface heterostructures) were configured as gas sensors and their sensing ability was measured. Both the surface-coarsened nanobelts and the Pd nanoparticle-decorated TiO₂ nanobelts exhibited dramatically improved sensitivity to ethanol vapor. Pd nanoparticle-decorated TiO₂ nanobelts with surface heterostructures exhibited the best sensitivity, selectivity, working temperature, response/recovery time, and reproducibility. The excellent ethanol sensing performance is attributed to the large surface area and enhancement by Schottky barrier-type junctions between the Pd nanoparticles and TiO₂ nanobelts.     

WO_3纳米片:基于无机-有机杂化前驱物的制备及光催化性能

以商业三氧化钨粉末做为钨源,通过合成WOx-EDA(EDA=乙二胺)无机-有机杂化纳米带为前驱物,再加盐酸酸化,迅速得到中间产物正交型钨酸单晶纳米片。再在空气气氛下,将中间产物在管式炉中煅烧2 h,最终得到单斜型三氧化钨单晶纳米片。一系列对比实验的结果表明,在由杂化纳米带转变成钨酸纳米片时,反应温度、反应时间、酸化浓度等实验参数对产物的结构和形貌有着很大的影响。通过计算,制得的三氧化钨纳米片带隙为2.48 eV。对比于商业三氧化钨粉末,三氧化钨纳米片在可见光降解罗丹明B(RhB)中表现出更优越的性能。