Preparation and characterization of CoFe2O4/TiO2 magnetic composite films

CoFe₂O₄/TiO₂ magnetic composite films were prepared using the sol-gel method with tetrabutyltitanate and metallic chlorates as starting materials. The effects of heat treatment temperatures on microstructures and on magnetic properties were studied. The microstructure and properties of the samples at different heat treatment temperatures were characterized by X-ray diffraction, Raman spectrum, scanning electron microscopy, polarized microscopy and vibrating sample magnetometry. The results show that crystals of different substances grow up independently. Cobalt ferrite is evenly embedded into the titanium dioxide matrix in the prepared composite films. The magnetism of the composite films is enhanced with an increase of the heat temperature. Supported by the National Natural Science Foundation of China (Grant Nos. 50632030 and 10474077), and the Natural Science Foundation of Shaanxi Province (Grant No. 2006E135)     

Preparation and characterization of CoFe_2O_4/TiO_2 magnetic composite films

CoFe2O4/TiO2 magnetic composite films were prepared using the sol-gel method with tetrabutyltitanate and metallic chlorates as starting materials. The effects of heat treatment temperatures on micro- structures and on magnetic properties were studied. The microstructure and properties of the samples at different heat treatment temperatures were characterized by X-ray diffraction, Raman spectrum, scanning electron microscopy, polarized microscopy and vibrating sample magnetometry. The results show that crystals of different substances grow up independently. Cobalt ferrite is evenly embedded into the titanium dioxide matrix in the prepared composite films. The magnetism of the composite films is enhanced with an increase of the heat temperature.     

Magnetostatic Coupling in CoFe2O4/Pb(Zr0.53Ti0.47)O3 Magnetoelectric Composite Thin Films of 2-2 Type Structure

CoFe₂O₄/Pb(Zr_0.53Ti_0.47)O₃ (CFO/PZT) magnetoelectric composite thin films of 2-2 type structure had been prepared onto Pt/Ti/SiO₂/Si substrate by a sol-gel process and spin coat-ing technique. The structure of the prepared thin film is substrate/PZT/CFO/PZT/CFO. Two CFO ferromagnetic layers are separated from each other by a thin PZT layer. The upper CFO layer is magnetostatically coupled with the lower CFO layer. Subsequent scan-ning electron microscopy (SEM) investigations show that the prepared thin films exhibit good morphologies and compact structure, and cross-sectional micrographs clearly display a multilayered nanostructure of multilayered thin films. The composite thin films exhibit both good magnetic and ferroelectric properties. The spacing between ferromagnetic layers can be varied by adjusting the thickness of intermediate PZT layer. It is found that the strength of magnetostatic coupling has a great impact on magnetoelectric properties of composite thin films, i.e., the magnetoelectric voltage coefficient of composite thin film tends to increase with the decreasing of pacing between two neighboring CFO ferromagnetic layers as a result of magnetostatic coupling effect.     

TiO2纳米管阵列负载不同形貌Cu2O薄膜的制备及光电性能研究

本论文采用阳极氧化法在金属钛基底上制备高度有序的TiO2纳米管阵列薄膜,然后采用脉冲电流法在TiO2纳米管阵列上沉积Cu2O,从而制备出Cu2O-TiO2纳米管阵列异质结复合薄膜。借助X射线衍射仪(XRD),场发射扫描电子显微镜(FESEM)和透射电子显微镜(TEM)等表征手段,详细探讨了Cu2O沉积过程中电解液的不同扰动方式(静止、磁力搅拌和超声搅拌)对复合薄膜物相和形貌的影响。实验结果表明电解液的扰动方式会影响Cu2O沉积过程中的离子扩散和微区化学环境,从而影响Cu2O的形貌。通过漫反射紫外-可见吸收光谱(UV-Vis)和光电流性能测试可知所制备的负载Cu2O型TiO2纳米管阵列薄膜具有显著的可见光响应效应。     

The effect of heat treatment in the reducing atmosphere on the physical properties of TiO2 thin films prepared by sol–gel method

Multilayered nanostructured TiO₂ thin films were prepared by sol–gel and dipping deposition on quartz substrate followed by thermal treatment under reducing atmosphere (20 %H₂–80 %Ar). Heat treatment at progressively higher temperatures caused structural, morphological, and optical changes, which were investigated by X-ray diffraction (XRD), atomic force microscopy, scanning electron microscopy, and UV–Vis spectroscopy. The conductivities of the thin films were also measured by 4-point probe method. The XRD results showed that the calcined TiO₂ thin films consist of single anatase phase which was completely transformed into rutile phase after heat treatment at 1,000 °C. The grains of films grew by intra-agglomerate densification after heat treatment at higher temperatures. The root mean square roughness of the samples was found to be in the range of 0.58–3.36 nm. The partially reduced TiO₂ samples have red-shifted transmittance bands due to new energy band formed by oxygen vacancies. The electrical conductivity of the films was also enhanced after heat treatment in reducing atmosphere.     

Preparation and Characterizations of TiO2/Organically Modified Silane Composite Materials Produced by the Sol-Gel Method

TiO₂/organically modified silane (ORMOSIL) composite materials produced by the sol-gel method were studied for optical waveguide applications. High optical quality waveguiding films on different substrates, including silicon, gallium arsenide, silica/silicon substrates, and microscope glass slides, were prepared from high titanium content (0.2 molar) ÿ-glycidoxypropyltrimethoxysilane at low temperature. Scanning electron microscopy (SEM), atomic force microscopy (AFM), differential thermal analysis (DTA), thermal gravimetric analysis (TGA), Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS) have been used to investigate the optical and structural properties of the composite films. The TGA/DTA results showed that the organic compounds in the film would tend to decompose in the temperature range from 200°C to 500°C. SEM and AFM results showed that a dense and porous-free composite material film could be obtained at the heat treatment temperature of 100°C. It was also shown that ORMOSIL is integrated in the glass, providing low shrinkage and high cracking resistance. The propagation loss properties of the composite films were also investigated. About 1.1 dB/cm propagation loss of the planar waveguide film was obtained at the wavelength of 633 nm.     

Magnetic and electrical properties of Cd3As2 + MnAs composite

A new ferromagnetic material based on a Cd₃As₂ + MnAs composite with the Curie point of 320 K has been prepared. Magnetic and electrical properties of the composite have been found to be determined by manganese arsenide nanoclusters. The composite has metallic conduction. Its resistance decreases with increasing magnetic field both at low and room temperatures, indicating spin-dependent scattering mechanisms and exchange interactions between magnetic nanoclusters in the composite.     

Improving barrier properties of polyethylene/Fe2O3-modified nanographene nanocomposites in a magnetic field

The present work aims at improving the barrier properties of high molecular weight Polyethylene/ graphene nanoplatelets (HMWPE/GnP) nanocomposites by aligning the embedded modified graphene nanoparticles in a magnetic field. Graphene nanoplatelets (GnP) were modified by magnetic Fe₂O₃ to produce Fe₂O₃-modified Graphene, GnP-mFe₂O₃. The magnetic properties of Fe₂O₃ were previously characterized by the vibrating sample magnetometer (VSM) method and resulting GnP-mFe₂O₃ nanoparticles were characterized by Fourier transform infrared (FTIR) analysis. HMWPE/GnP nanocomposites were prepared via melt mixing. The prepared nanocomposites were sheeted at high temperatures in a magnetic field using a hot press. The barrier properties of prepared films, HMWPE/GnP and HMWPE/GnP-mFe₂O₃ were characterized by carrying out a permeation to oxygen experiment as a function of GnP and GnP-mFe₂O₃ contents. A decrease in gas transmission rate (GTR) was observed for the samples after being subjected to the magnetic field compared to the non-treated sample. The results of differential scanning calorimetry (DSC) and field emission electron microscopy (FESEM) experiments confirmed the orientation of GnP-mFe₂O₃ nanoparticles in nanocomposites.     

Crystallization Behavior of SiO2-TiO2 Sol-Gel Thin Films

The aim of this work was to investigate the crystallization behavior of thin films of SiO₂−TiO₂ made by the sol-gel process as function of the TiO₂ content and the temperature and time of heat treatment. Precursor solutions were prepared by hydrolysis of TEOS (tetraethoxysilane) and TPOT (titaniums tetraisopropoxide). Multilayer films were spun on single crystal silicon wafers. The compositions studied were (on a molar percentage basis) 20TiO₂−80SiO₂, 30TiO₂−70SiO₂, 40TiO₂−60SiO₂ and pure TiO₂. The films were heat treated at different temperatures between 300°C and 1200°C, for different periods of time (30 s-90 h). The crystallization kinetics were followed by micro-Raman spectrometry. Grazing incidence X-ray diffraction showed that the films crystallized into one or both of two crystalline phase of TiO₂: anatase and rutile (for pure TiO₂ only). The volume fractions of the crystalline phase varied from very low values (<1%), up to 100%, for a TiO₂ sample heat treated at 800°C for 8 hours. The results show that the volume fraction of crystalline phase is strongly influenced by the heat treatment temperature and also, to a smaller extent, by the heat treatment time. The most important parameter, however, is the composition of the films: the higher their TiO₂ concentration, the lower is the crystallization temperature and the larger is the crystallized fraction.     

Structural and Optical Properties of Sol-Gel Deposited Proton Conducting Ta2O5 Films

Proton conducting tantalum oxide films were deposited on ITO (Indium Tin Oxide) coated glass, fused silica and soda-lime glass substrates by spin coating using a sol-gel process. The coating solutions were prepared using Ta(OC₂H₅)₅ as a precursor. X-ray diffraction studies determined that the sol-gel films, heat treated at temperatures below 400°C, were amorphous. Films heat treated at higher temperatures were crystalline with the hexagonal δ-Ta₂O₅ structure. The solar transmission values (T _s ) of tantala films on glass generally range from 0.8–0.9, depending on thickness. The refractive index and the extinction coefficient were evaluated from transmittance characteristics in the UV-VIS-NIR regions. The refractive index values calculated at λ=550 nm increased fromn=1.78 to 1.97 with increasing heat treatment from 150 to 450°C. The films heat treated at different temperatures showed low absorption, with extinction coefficients of smaller thank=1×10⁻³ in the visible range. Impedance spectroscopic investigations performed on Ta₂O₅ films revealed that these films have a protonic conductivity of 3.2×10⁻⁴S/m. The films are suitable for proton conducting layers in electrochromic (EC) devices.     

Formation of Anatase Nanocrystals in Sol-Gel Derived TiO2-SiO2 Thin Films with Hot Water Treatment

We have successfully prepared transparent and porous anatase nanocrystals-dispersed films by treating the sol-gel derived TiO₂-SiO₂ films containing poly(ethylene glycol), PEG, with hot water. This process was done at temperatures lower than 100°C under atmospheric pressure, and thus anatase nanocrystals-dispersed films can be formed on various kinds of substrates including organic polymers with poor heat resistance. The changes in structure and composition of the TiO₂-SiO₂ gel films with hot water treatment were related to the formation process of anatase nanocrystals in the TiO₂-SiO₂ gel films with hot water treatment. The formation of anatase nanocrystals was found to proceed to hydrolysis of Si–O–Ti bonds and dissolution of SiO₂ component. In addition, porous film structure formed by leaching of PEG with hot water treatment led to homogenous dispersion of anatase nonocrystals in the films.     

CuInS2：两步电沉积制备及性能

采用恒电位沉积法制备铜铟合金预制膜,并存管式炉中通过固态源蒸发硫化预制膜得到CuInS:薄膜.通过扫描电镜(SEM)、能量色散谱仪(EDS)和X射线衍射仪(XRD)对CuInS2薄膜的表而形貌、截面厚度、成分组成和薄膜的组织结构进行了研究,并利用紫外可见光吸收谱仪(UV-Vis)研究了不同硫化温度对CuInS:薄膜的形貌及其光学吸收性质的影响.结果表明:不同的退火温度能够影响CuInS:薄膜的表面形貌以及带隙的大小,从而影响其光学吸收特性.     

Structure and photochromic properties of molybdenumphosphoric acid/TiO<Subscript>2</Subscript> composite films

TiO₂ sol-gel composite films with dropping molybdenumphosphoric acid (PMoA) have been prepared by sol-gel method. The structure and constitute of composite thin films were studied with Fourier transforms infrared spectroscopy (FT-IR) atomic force microscopy (AFM), and X-ray diffraction (XRD) patterns, respectively. The photochromic behavior and mechanism of composite thin films were investigated with ultraviolet-visible spectra (UV-vis) and electron spin resonance (ESR). FT-IR results showed that the Keggin geometry of PMoA was still preserved inside PMoA/TiO₂ composite thin films, and a charge transfer bridge was built at the interface of PMoA and TiO₂ through the Mo-O-Ti bond. Surface topography of the composite film showed obvious changes before/after adding PMoA, and the surface topography of composite films showed obvious changes before/after irradiating as well. Composite thin film had reversible photochromic properties. Irradiated with UV light, transparent films changed from colorless to blue and they can bleach completely with ambient air in the dark. ESR results showed that TiO₂ were excitated by UV light to produce electrons, which deoxidized PMoA to produce heteropolyblues. The photochromic process of PMoA/TiO₂ system was carried through electron transfer mechanism.     

The Effect of SiO2 Addition on the Grain Size and Photocatalytic Activity of TiO2 Thin Films

The uniform transparent TiO₂/SiO₂ nanometer composite thin films were prepared via sol-gel method on the soda lime glass substrates, and were characterized by X-ray photoelectron spectroscopy (XPS), FTIR spectroscopy, UV-VIS spectroscopy, transmission electron microscopy (TEM), X-ray diffraction (XRD) and BET surface areas. It was found that the addition of SiO₂ to TiO₂ thin films could suppress the grain growth of TiO₂ crystal and increase the hydroxyl content of the surface of TiO₂ films. The photocatalytic activity of the as-prepared TiO₂/SiO₂ composite thin films increases for SiO₂ content of less than 5 mol%.     

Mechanical Properties of Electrostatically Self-Assembled Al2O3–ZrO2 Nanocomposites Prepared at Room Temperature

Alternate layers of Al₂O₃ and ZrO₂ nanocomposite films were prepared on silicon wafers and glass substrates at room temperature using the electrostatic self-assembly monolayer (ESAM) process. The versatile approach of the ESAM process provides the possibility of integrating diverse inorganic colloids on the nanosize level in a layer-by-layer or block-by-block fashion. Further, it allows the combination of inorganic colloids and organic molecules, making it possible to fabricate thick films with large pores and good stress relaxation. Highly ordered, micron-thick films have been formed, sintered, and characterized by scanning electron microscopy and ellipsometry. There is no significant visible crack formation for Al₂O₃–ZrO₂ composite films after heat treatment at 1200°C for 2 h, although significant thickness reduction occurs. The hardness and Young's modulus of these films before and after sintering were measured using nanoindentation techniques.     

Investigation on multiferroic,optical and photoluminescence properties of CoFe2O4/(Pb1−xSrx)TiO3 nanostructured composite thin films

Multiferroic nanostructured composite thin films consisting of CoFe₂O₄ (CFO) and Pb_1−xSr_xTiO3 (PST; x = 0.1, 0.2, 0.3, 0.4 and 0.5) layers have been deposited on Pt/TiO₂/SiO₂/Si and quartz substrates by using metallo-organic decomposition process and spin coating. The effect of Sr content on the multiferroic and optical properties have been investigated. The phase purity such as spinel structure of CFO and perovskite structure of PST has been verified by X-ray diffraction. Cross-sectional scanning electron microscopy images revealed clear interface between CFO and PST layers without any noticeable diffusion. The multiferroic properties of CFO/PST composite films have been confirmed by magnetic and ferroelectric hysteresis loops with low leakage current density. The residual strain sensitivity of multiferroic and optical properties has been observed in the composite films. The decrease in saturation magnetization and saturation polarization with increase in Sr content has been observed which could be attributed to the decrease in residual strain of CFO/PST composite films. The magnetic phase transition temperature of the CFO/PST composite films is also reduced. The optical refractive index decreases with increase of amount of Sr content. The photoluminescence spectra of the CFO/PST composite films possess a blue shift which can be attributed to the Pb and oxygen vacancies as localized sensitizing centers. We show that the multiferroic and optical properties of the CFO/PST composite films are highly sensitive to the heterostructure strains which can be controlled by Sr content.     

Nanocomposites of TiO 2 and Siloxane Copolymers as Environmentally Safe Flame-Retardant Materials †

Composites of titanium dioxide (TiO₂) nanoparticles and biocatalytically synthesized dimethylsiloxane copolyamides were prepared, and their thermal and flame-retardant properties were investigated. The flammability properties such as heat release capacity and total heat release were measured from microscale cumbustion calorimetry (MCC). The thermal degradation temperatures, char yields, and the heat-release capacities of these nanocomposites were significantly improved over the pure polymers. The heat-release capacities of the siloxane copolymer nanocomposites with 20wt% of TiO₂ were found to be 167 and 129 J/g K, which is a 35% less than the pure polymers (260 and 194 J/g K, respectively). The SEM/EDAX surface-analysis studies on nanocomposite films and their char revealed that nanocrystalline-TiO₂ plays an important role in forming carbonaceous silicate char on the surface as a protective layer.     

Structure and properties of regenerated cellulose/tourmaline nanocrystal composite films

Nanocomposite films were successfully prepared from cellulose and tourmaline nanocrystals with mean diameters of 70 nm in a 1.5 M NaOH/0.65 M thiourea aqueous solution by coagulation with 5 wt % CaCl₂ and then a 3 wt % HCl aqueous solution for 2 min. The structure and properties of the composite films were characterized by X‐ray diffraction, scanning electron microscopy, transmission electron microscopy, dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and tensile testing. The results indicated that the tourmaline nanocrystals were dispersed in a cellulose matrix, maintaining the original structure of the nanocrystals in the composite films. The loss peaks (tan δ) in the DMA spectra and the decomposition temperatures in the DSC curves of the composite films were significantly shifted toward low temperatures, suggesting that the nanocrystals broke the partial intermolecular hydrogen bonds of cellulose, and this led to a reduction in the thermal stability. However, the nanocomposite films exhibited a homogeneous structure and dispersion of the nanocrystals. When the tourmaline content was in the range of 4–8 wt %, the composite films possessed good tensile strength (92–107 MPa) and exhibited obvious antibacterial action against Staphylococcus aureus. This work provides a potential way of preparing functional composite films or fibers from cellulose and nanoinorganic particles with NaOH/thiourea aqueous solutions. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 367–373, 2004     

Synthesis and characterization of novel magnetic Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/polyurethane foam composite applied to the carrier of immobilized microorganisms for wastewater treatment

The objective of this work was to prepare novel magnetic Fe₃O₄/polyurethane foam (Fe₃O₄/PUF) composites applied to the carriers of immobilized microorganisms for toluene-containing wastewater treatment. The morphology and structure of Fe₃O₄/PUF composite were characterized by X-ray diffraction, Fourier transform IR spectroscopy, thermogravimetric analysis, differential scanning calorimetry, scanning electron microscopy, and magnetic property measurement system. These morphological investigations revealed that Fe₃O₄ nano-particles were well dispersed into the matrix of PUF with nano-scale diameter particles. TG experiments indicated that the initial thermal weight loss temperatures of composite with the content of 2.5 wt% and 7.5% Fe₃O₄ were increased by 7 and 16 °C, compared with pure PUF. The degradation efficiency of toluene with magnetic PUF composite was much higher than that of pure PUF carrier, and the reason why the immobilization of microbial biomass of microorganisms on the magnetic PUF composite was much higher than that of the pure PUF. The prepared magnetic Fe₃O₄/PUF composite offered excellent thermal stability and medium paramagnetic properties. And this composite could not only increase the immobilized biomass of the microorganisms, but also enhance the COD removal efficiency of wastewater.     

Sol–gel synthesis of mesoporous WO3–TiO2 composite thin films for photochromic devices

Mesoporous WO₃–TiO₂ composite films were prepared by a sol gel based two stage dip coating method and subsequent annealing at 450, 500 and 600 °C. An organically modified silicate based templating strategy was adopted in order to obtain a mesoporous structure. The composite films were prepared on ITO coated glass substrates. The porosity, morphology, and microstructures of the resultant products were characterized by scanning electron microscopy, N₂ adsorption–desorption measurements, μ-Raman spectroscopy and X-ray diffraction. Calcination of the films at 450, and 500 °C resulted in mixed hexagonal (h) plus monoclinic phases, and pure monoclinic (m) phase of WO₃, respectively. The degree of crystallization of TiO₂ present in these composite films was not evident. The composite films annealed at 600 °C, however, consist of orthorhombic (o) WO₃ and anatase TiO₂. It was found that the o-WO₃ phase was stabilized by nanocrystalline anatase TiO₂. The thus obtained mesoporous WO₃–TiO₂ composite films were dye sensitized and applied for the construction of photochromic devices. The device constructed using dye sensitized WO₃–TiO₂ composite layer heat treated at 600 °C showed an optical modulation of 51 % in the NIR region, whereas the devices based on the composite layers heat treated at 450, and 500 °C showed only a moderate optical modulation of 24.9, and 38 %, respectively. This remarkable difference in the transmittance response is attributed to nanocrystalline anatase TiO₂ embedded in the orthorhombic WO₃ matrix of the WO₃–TiO₂ composite layer annealed at 600 °C.