Ring‐Opening Polymerization of ε‐Caprolactone by Poly(ethylene glycol) by an Activated Monomer Mechanism

Summary: The polymerization of ε‐caprolactone (CL) in the presence of HCl · Et₂O by an activated monomer mechanism was performed to synthesize diblock or triblock copolymers composed of poly(ethylene glycol) (PEG) and poly(ε‐caprolactone) (PCL). The obtained PCLs had molecular weights close to the theoretical values calculated from the CL to PEG molar ratios and exibited monomodal GPC curves. We successfully prepared PEG and PCL block copolymers by a metal‐free method.

The non‐metal catalyzed living ring‐opening polymerisation of ε‐caprolactone by PEG.     

Preparation of Poly(ε‐caprolactone)/Clay Nanocomposites by Microwave‐Assisted In Situ Ring‐Opening Polymerization

PCL/clay nanocomposites were prepared by microwave‐assisted in situ ROP of ε‐caprolactone in the presence of either unmodified clay (Cloisite® Na⁺) or clay modified by quaternary ammonium cations containing hydroxyl groups (Cloisite 30B). This PCL showed significantly improved monomer conversion and molecular weight compared with that produced by conventional heating. An intercalated structure was observed for the PCL/Cloisite Na⁺ nanocomposites, while a predominantly exfoliated structure was observed for the PCL/Cloisite 30B nanocomposites. Microwave irradiation proved to be an effective and efficient method for the preparation of PCL/clay nanocomposites.

     

L,L‐Lactide and ε‐Caprolactone Block Copolymers by a ‘Poly(L,L‐lactide) Block First’ Route

L,L ‐lactide (LA) and ε‐caprolactone (CL) block copolymers have been prepared by initiating the poly(ε‐caprolactone) (PCL) block growth with living poly(L,L ‐lactide) (PLA*). In the previous attempts to prepare block copolymers this way only random copolyesters were obtained because the PLA* + CL cross‐propagation rate was lower than that of the PLA–CL* + PLA transesterification. The present paper shows that application of Al‐alkoxide active centers that bear bulky diphenolate ligands results in efficient suppression of the transesterification. Thus, the corresponding well‐defined di‐ and triblock copolymers could be prepared.

     

Crystallization of Poly(ε‐caprolactone)/Poly(vinyl chloride) Miscible Blends Under Strain: The Role of Molecular Weight

Summary: The effect of poly(ε‐caprolactone) (PCL) molecular weight on the orientation of crystalline PCL in miscible poly(ε‐caprolactone)/poly(vinyl chloride) (PCL/PVC) blends, melt crystallized under strain, has been studied by a combination of wide angle X‐ray diffraction (WAXD) and small angle X‐ray scattering (SAXS) studies. An unusual crystal orientation with the b‐axis parallel to the stretching direction was observed in miscible PCL/PVC blends with PCL of high molecular weight (>21 000). SAXS showed the presence of nanosize confined PCL in the PCL/PVC blends, which could be preserved at temperatures higher than the T_m of PCL but lower than the T_g of PVC. A mechanism based on the confinement of PCL crystal growth was proposed, which can explain the formation of b‐axis orientation in PCL/PVC blends crystallized under strain.

SAXS pattern of stretched PCL/PVC blend after annealing at 90 °C for 5 min.     

Novel Amphiphilic Degradable Poly(ε‐caprolactone)‐graft‐poly(4‐vinyl pyridine), Poly(ε‐caprolactone)‐graft‐poly(dimethylaminoethyl methacrylate) and Water‐Soluble Derivatives

New amphiphilic graft copolymers that have a poly(ε‐caprolactone) (PCL) biodegradable hydrophobic backbone and poly(4‐vinylpyridine) (P4VP) or poly(2‐(N,N‐dimethylamino)ethyl methacrylate) (PDMAEMA) hydrophilic side chains have been prepared by anionic polymerization of the corresponding 4VP and DMAEMA monomers using a PCL‐based macropolycarbanion as initiator. The water solubility of these amphiphilic copolymers is improved by quaternization, which leads to fully water‐soluble cationic copolymers that give micellar aggregates in deionized water with diameters ranging from 65 to 125 nm. In addition, to improve the hydrophilicity of PCL‐g‐P4VP, grafting of poly(ethylene glycol) (PEG) segments has been carried out to give a water‐soluble double grafted PCL‐g‐(P4VP;PEG) terpolymer.

     

Synthesis and Ring Opening Polymerization of a New Functional Lactone, α‐Iodo‐ε‐caprolactone: A Novel Route to Functionalized Aliphatic Polyesters

A new functional lactone, α‐iodo‐ε‐caprolactone (αIεCL), was synthesized from ε‐caprolactone by anionic activation using a non‐nucleophilic strong base (lithium diisopropylamide) followed by an electrophilic substitution with iodine chloride. Ring‐opening (co)polymerizations of the resulting monomer with ε‐caprolactone were carried out using tin 2‐ethylhexanoate as a catalyst in toluene at 100 °C. Homopolymerization of αIεCL was achieved, and poly(αIεCL) was fully characterized by SEC, ¹H NMR and elemental analysis. Random copolymerizations of αIεCL with εCL were controlled with experimental molecular weights close to the theoretical values, narrow molecular weight distributions and a good agreement between experimental and theoretical molar compositions of αIεCL.

     

Self‐Catalysis of Phthaloylchitosan for Graft Copolymerization of ε‐Caprolactone with Chitosan

Summary: A protection‐graft‐deprotection method was developed to prepare chitosan‐g‐polycaprolactone graft copolymers, during which the ring‐opening copolymerization of ε‐caprolactone onto phthaloylchitosan (PHCS) happened without any additional catalysis. The intermediate PHCS was introduced primarily to protect the active amino group of chitosan. After controlled experiments, the phthalimido compound was proposed to be a novel kind of organic catalyst for the ring‐opening polymerization of caprolactone monomers, while the hydroxyl group acted as an initiator. Hence, in this graft system, PHCS was endowed with both self‐catalysis and self‐initiation at the same time, and the PCL side chains grew from the hydroxyl groups of the chitosan backbone.

     

Enhanced Templating in the Crystallisation of Poly(ε‐caprolactone) Using 1,3:2,4‐di(4‐Chlorobenzylidene) Sorbitol

We show that small quantities of 1,3:2,4‐di(4‐chlorobenzylidene) sorbitol dispersed in poly(ε‐caprolactone) provide a very effective self‐assembling nanoscale framework which, with a flow field, yields extremely high levels of polymer crystal orientation. During modest shear flow of the polymer melt, the additive forms highly extended nano‐particles which adopt a preferred alignment with respect to the flow field. On cooling, polymer crystallisation is directed by these particles. This chloro substituted dibenzylidene sorbitol is considerably more effective at directing the crystal growth of poly(ε‐caprolactone) than the unsubstituted compound.

     

Influence of Microwave Irradiation on the Lipase‐Catalyzed Ring‐Opening Polymerization of ε‐Caprolactone

Summary: The microwave (MW)‐assisted lipase‐catalyzed ring‐opening polymerization of ε‐caprolactone in boiling solvents was investigated for the first time. In case of boiling toluene or benzene the MW‐assisted reaction proceeded significantly slower compared to oil bath heating. On the other hand, using boiling diethyl ether as solvent, an increase of the polymerization rate due to MW irradiation was found. Yield, molecular weight measurements, and MALDI‐TOF analysis supported the results.

Reactivity of the MW‐assisted ring‐opening polymerization of ε‐caprolactone compared with conventional thermal heating in different solvents.     

Preparation of Highly Transparent and Thermally Stable Films of α‐Cyclodextrin/Polymer Inclusion Complexes

Films of an α‐cyclodextrin/poly(ε‐caprolactone) inclusion complex have been successfully prepared and show high transparency and heat resistance in comparison to the pure polymer film. The physical properties, such as transparency, mechanical properties, and thermal stability, of the α‐CD‐PCL‐IC films are found to depend on the α‐cyclodextrin‐to‐polymer stoichiometry.

     

The Use of a Low‐Molar‐Mass Self‐Assembled Template to Direct the Crystallisation of Poly(ε‐caprolactone)

Summary: We show that small quantities of dibenzylidene sorbitol dispersed in poly(ε‐caprolactone) provide a self‐assembling nanoscale framework to yield high levels of crystal orientation. During modest shear flow of the melt, the additive forms highly extended nanoparticles which adopt a preferred alignment with respect to the flow field and, on cooling, polymer crystallisation is directed by these particles. We speculate that atomistic level epitaxy is unlikely to be the only directing influence.

SAXS pattern of PCL/DBS in the melt at 80 °C and subjected to a shear flow of 10 s⁻¹ for 1 000 shear units. The flow direction is vertical.     

Fabrication of Compositional‐Gradient Biodegradable Polymeric Films Showing Self‐Bending Deformation

A compositional graded film of poly(ε‐caprolactone) (PCL) with 4,4′‐thiodiphenol (TDP), in the film thickness direction, was fabricated by self‐diffusing of TDP in the PCL melt. We found out the self‐bending deformation of the gradient film, which bent into a rolled‐up shape by itself. The initial shape of the film was flat when the sample was quenched from the melt. Upon the fast crystallization of PCL, the gradient film bent to the side with low TDP content. Then, after PCL crystallized the film bent to the opposite direction, that is, to the side with high TDP content. This bending to the TDP rich region was induced by not only the crystallization of PCL but also mass transfer due to the diffusion of TDP from TDP rich region to poor region.

     

A Facile Strategy for Preparation of α‐Heterobifunctional Polystyrenes with Well‐Defined Molecular Weight

A facile strategy for synthesis of α‐heterobifunctional polystyrenes is reported. The novel functional polystyrenes have been successfully synthesized via a combination of atom transfer radical polymerization (ATRP) and chemical modification of end‐functional groups. First, ε‐caprolactone end‐capped polystyrenes with controlled molecular weight and low polydispersity were prepared by ATRP of styrene using α‐bromo‐ε‐caprolactone (αBrCL) as an initiator. Then, removal of the terminal bromine atom was performed with iso‐propylbenzene in the presence of CuBr/PMDETA. Finally, ring‐opening modifications of the caprolactone group were carried out with amines, n‐butanol and H₂O to produce novel polystyrenes containing two different functional groups at one end.

     

Microwave‐Assisted Ring‐Opening Polymerization of ε‐Caprolactone in the Presence of Ionic Liquid

Summary: Microwave‐assisted ring‐opening polymerization of ε‐caprolactone in the presence of 1‐butyl‐3‐methylimidazolium tetrafluoroborate ionic liquid using zinc oxide as a catalyst is investigated. By adding 30 wt.‐% ionic liquid, poly(ε‐caprolactone) with a weight‐average molar mass of 28 500 g · mol⁻¹ is obtained at 85 W for 30 min. The results indicate that the polymerization could be efficiently enhanced in the presence of ionic liquids under microwave irradiation because ionic liquids can effectively absorb microwave energy.

     

Poly(2‐vinylpyridine)‐block ‐Poly(ϵ‐caprolactone) Single Crystals in Micellar Solution

Self‐assembly of poly(2‐vinylpyridine)‐block‐poly(ϵ‐caprolactone) (P2VP‐b‐PCL) diblock copolymer in the presence of a selective solvent is investigated by transmission electron microscopy and atomic force microscopy. Addition of water into a P2VP‐b‐PCL solution in N,N‐dimethylformamide at 20 °C produces elongated truncated lozenge shaped single crystals of uniform size and shape in large quantities. The single crystals are composed of PCL single‐crystal layer sandwiched between two P2VP layers tethered on the top and bottom basal surfaces. The formation of the single crystals is found to depend on the temperature. These findings provide a facile approach to the preparation of uniform single crystals in large quantities.

     

Enzyme‐Catalyzed Preparation of Aliphatic Polyesters Containing Thioester Linkages

Aliphatic polyesters containing thioester linkages were enzymatically prepared by both the copolymerization of lactone with mercaptoalkanoic acid and by the transesterification of polyesters with mercaptoalkanoic acids. The enzymatic copolymerization of ε‐caprolactone with 11‐mercaptoundecanoic acid (11MU) and 3‐mercaptopropionic acid (3MP) was performed under reduced pressure using an immobilized lipase from Candida antarctica (CA). The transesterification of poly(ε‐caprolactone) and poly[(R)‐3‐hydroxybutyrate] was carried out with 11MU and 3MP using lipase CA under reduced pressure.

     

Precision Polyolefin Nanoalloy Polypropylene/Poly(ε‐caprolactone)

This communication reports the first example of precision polyolefin nanoalloys where an exotic immiscible polymer is nanometrically dispersed with stability in a polyolefin matrix in a highly controlled mode. Following the preparation of polypropylene/multiwalled carbon nanotubes nanocomposites (PP/MWCNTs) by in situ Ziegler‐Natta polymerization, the hydroxyl groups on the surfaces of individual MWCNTs are used to initiate ring‐opening polymerization of ε‐caprolactone, resulting in PP/poly(ε‐caprolactone) (PCL) alloy with PCL grafted on MWCNTs. Upon phase formation, the PP/MWCNTs‐g‐PCL alloys exhibit a unique PCL dispersion morphology, which is stable and solely governed by PCL molecular weight.

     

The Self‐Assembled Structure of the Diblock Copolymer PCL‐b‐P4VP Transforms Upon Competitive Interactions with Octaphenol Polyhedral Oligomeric Silsesquioxane

This paper describes the miscibility and self‐assembly, mediated by hydrogen‐bonding interactions, of new block copolymer/nanoparticle blends. The morphologies adopted by the immiscible poly[(ε‐caprolactone)‐block‐(4‐vinyl pyridine)] (PCL‐b‐P4VP) diblock copolymer changes upon increasing the number of competitive hydrogen‐bonding interactions after adding increasing amounts of octaphenol polyhedral oligomeric silsesquioxane (OP‐POSS). Transmission electron microscopy reveals morphologies that exhibit high degrees of long‐range order, such as cylindrical and spherical structures, at relatively low OP‐POSS contents, and short‐range order or disordered structures at higher OP‐POSS contents. Analyses performed using differential scanning calorimetry, wide‐angle X‐ray diffraction, and FT‐IR spectroscopy provide positive evidence that the pyridyl units of the P4VP block are significantly stronger hydrogen‐bond acceptors toward the OH group of OP‐POSS than are the CO groups of the PCL block, thereby resulting in excluded and confined PCL phases.

     

Thermoreversibly Crosslinked Poly(ε‐caprolactone) as Recyclable Shape‐Memory Polymer Network

A new concept to build shape memory polymers (SMP) combining outstanding fixity and recovery ratios (both above 99% after only one training cycle) typical of chemically crosslinked SMPs with reprocessability restricted to physically crosslinked SMPs is demonstrated by covalently bonding, through thermoreversible Diels–Alder (DA) adducts, star‐shaped poly(ε‐caprolactones) (PCL) end‐functionalized by furan and maleimide moieties. A PCL network is easily prepared by melt‐blending complementary end‐functional star polymers in retro DA regime, then by curing at lower temperature to favour the DA cycloaddition. Such covalent network can be reprocessed when heated again at the retro DA temperature. The resulting SMP shows still excellent shape memory properties attesting for its good recyclability.

     

Rheology of Polydisperse Star Polymer Melts: Extension of the Parameter‐Free Tube Model of Milner and McLeish to Arbitrary Arm‐Length Polydispersity

Summary: This paper considers the extension of the parameter‐free tube model of Milner and McLeish for stress relaxation in melts of monodisperse star polymers to star polymers whose arms have a continuous molecular weight distribution such as the Flory distribution in the case of star‐nylons and star‐polyesters. Exact expressions are derived for the relaxation spectrum and the relaxation modulus for star polymers having an arbitrary continuous arm‐length distribution. For a Flory distribution a comparison is made with results of dynamic measurements on a melt of 8‐arm poly(ε‐caprolactone) (PCL) stars. An excellent quantitative agreement over a large frequency range is found, however, only if one treats, in contrast with the original parameter‐free tube model approach, the entanglement molecular weight that determines the relaxation spectrum as a fitting parameter independent of the entanglement molecular weight of the linear PCL. This discrepancy is not in anyway related to the polydispersity in arm‐length, but a consequence of the thermorheological complexity of the PCL stars. A similar discrepancy has been observed for hydrogenated polybutadiene stars, as described by Levine and Milner.

Measured and calculated storage moduli G′ as a function of frequency ω.