Characterization of the surface charge property and porosity of track-etched polymer membranes

As an important property of porous membranes, the surface charge property determines many ionic behaviors of nanopores, such as ionic conductance and selectivity. Based on the dependence of electric double layers on bulk concentrations, ionic conductance through nanopores at high and low concentrations is governed by the bulk conductance and surface charge density, respectively. Here, through the investigation of ionic conductance inside track-etched single polyethylene terephthalate (PET) nanopores under various concentrations, the surface charge density of PET membranes is extracted as ∼−0.021 C/m² at pH 10 over measurements with 40 PET nanopores. Simulations show that surface roughness can cause underestimation in surface charge density due to the inhibited electroosmotic flow. Then, the averaged pore size and porosity of track-etched multipore PET membranes are characterized by the developed ionic conductance method. Through coupled theoretical predictions in ionic conductance under high and low concentrations, the averaged pore size and porosity of porous membranes can be obtained simultaneously. Our method provides a simple and precise way to characterize the pore size and porosity of multipore membranes, especially for those with sub-100 nm pores and low porosities.     

Effect of porogen on the physico-chemical properties and degradation performance of PLGA scaffolds

The aim of the study was to examine the relationship between the structural features of PLGA 3-D scaffolds and their degradation performances. PLGA 3-D scaffolds were fabricated by solvent casting and particulate leaching using salt and sucrose particles as porogen and they were characterized in terms of structure, physico-chemical and mechanical properties. The in vitro degradation study was performed at 37 °C in PBS for 28 days and it included the determination of Mw, Mn, PI, water uptake, mass loss and pH changes of the degradation buffer. It was found that the preparation method scaffolds, in particular the choice of the porogen type and was responsible for the three-dimensional structure (pore size, porosity, apparent density and, mechanical properties) of the scaffold and for physico-chemical PLGA polymer modifications (polymer degradation reactions, polymer chain rearrangement, Tg changes). Scaffolds with high porosity (83.8-89.4%) and an interconnected network were obtained.     

Effect of starch content on the biodegradation of polycaprolactone/starch composite for fabricating in situ pore-forming scaffolds

Bone tissue engineering is an efficient approach to regenerating bone-related defects. The optimal scaffold used for bone tissue engineering must possess adequate porosity and suitable mechanical properties. This work described the development of a biodegradable polymeric composite based on polycaprolactone (PCL) and starch that can form a porous structure in situ. The scaffold exhibited the required mechanical properties at the initial stage of implantation by controlling in situ degradation and subsequent pore formation. PCL/starch (SPCL) scaffolds with 100/0, 70/30, and 50/50 ratios were developed. Degradation studies were performed in phosphate buffer saline (PBS) containing α-amylase or lipase at 37 °C for 4 weeks. Fourier-transform infrared spectroscopy was used to analyze chemical bonds and their changes after degradation. Differential scanning calorimetry was applied to determine the crystallinity and recrystallization of samples before and after degradation. Mass loss and starch release were observed during degradation, and the porosity of samples was measured by the ethanol replacement method. Morphology was further determined using scanning electron microscopy. Finally, variations in compressive strength and modulus during degradation and pore formation were also measured. The porosity of samples reached 45% after 1 month of degradation, and mechanical properties were still appropriate for human bone tissue. Reduction in mechanical property after mass loss, starch release and pore formation was controlled by the hydrogen bonding and recrystallization effect of PCL after degradation. Results suggested that SPCL composite had potential to form porous scaffold with adequate mechanical properties in situ and is promising for bone tissue engineering applications.     

低热-高压法制备PLGA多孔支架及其体外降解研究

采用低热-高压法制备了聚(dl-丙交酯／乙交酯)75／25(PLGA75／25)组织工程多孔支架。该方法避免了使用有机溶剂，支架的孔隙率在90％以上，孔径大小分布均匀。多孔支架经过酒精处理后，支架表面产生许多微小的凹陷；用藻酸钙改性处理后，支架形态保持良好。两种处理都使支架的压缩强度有所增大，亲水性增强。虽然孔隙率高的支架降解速率稍慢，但其体外降解规律基本一致：特性粘数争力学强度衰减快，而质量损失较慢，降解6周后，支架的质量损失仅为3％左右；体外降解3周后，支架的形态保持良好，可望在细胞移植争组织修复的早期发挥支撑作用。     

3D printed polylactic acid nanocomposite scaffolds for tissue engineering applications

In this study, biodegradable polylactic acid (PLA) and PLA nanocomposite scaffolds reinforced with magnetic and conductive fillers, were processed via fused filament fabrication additive manufacturing and their bioactivity and biodegradation characteristics were examined. Porous 3D architectures with 50% bulk porosity were 3D printed, and their physicochemical properties were evaluated. Thermal analysis confirmed the presence of ~18 wt% of carbon nanostructures (CNF and GNP; nowonwards CNF) and ~37 wt% of magnetic iron oxide (Fe₂O₃) particles in the filaments. The in vitro degradation tests of scaffolds showed porous and fractured struts after 2 and 4 weeks of immersion in DMEM respectively, although a negligible weight loss is observed. Greater extent of degradation is observed in PLA with magnetic fillers followed by PLA with conductive fillers and neat PLA. In vitro bioactivity study of scaffolds indicate enhancement from ~2.9% (PLA) to ~5.32% (PLA/CNF) and ~ 3.12% (PLA/Fe₂O₃). Stiffness calculated from the compression tests showed decrease from ~680 MPa (PLA) to 533 MPa and 425 MPa for PLA/CNF and PLA/Fe₂O₃ respectively. Enhanced bioactivity and faster biodegradation response of PLA nanocomposites with conductive fillers make them a potential candidate for tissue engineering applications such as scaffold bone replacement and regeneration.     

Morphological behaviour of poly(lactic acid) during hydrolytic degradation

The hydrolytic degradation and the morphological behaviour of a packaging grade of poly(lactic acid) (PLA) were characterized by a series of techniques. During the initial degradation process (stage 1) at a temperature near the glass transition temperature (T_g), the molecular weight of PLA decreased as degradation time increased following a bulk erosion mechanism while the crystallinity increased simultaneously, but no observable weight loss occurred at stage 1. Mainly α-form PLA crystal structure was formed for the crystalline PLA with a low content of d stereo-isomers, but the material displayed a lower regularity, smaller domain size, lower melting temperatures T_m and different motional dynamics as compared to the original PLA with a similar level of crystallinity achieved by annealing. The amorphous PLA with a higher amount of d stereo-isomers also yielded the α crystalline phase as well as stereo-complex crystals at stage 1. When the molecular weight and the crystallinity reached a stable level, PLA started erosion into the degrading aqueous medium. During this stage of degradation (stage 2), the crystalline structure in PLA residues was further modified and both pH and temperature influenced the modification. The degradation at stage 2 was likely to follow a surface erosion mechanism with lactic acid as the major product of the weight loss. Besides the crystallinity effect on the degradation, temperature also played a key role in determining the rate of PLA degradation in both stages. The process was very slow at temperatures below the T_g of PLA but the rate was greatly enhanced at temperatures above the T_g.     

Preparation and Characterization of Polyhydroxyalkanoates Macroporous Scaffold Through Enzyme-Mediated Modifications

Polyhydroxyalkanoates (PHAs) are hydrophobic biodegradable thermoplastics that have received considerable attention in biomedical applications due to their biocompatibility, mechanical properties, and biodegradability. In this study, the degradation rate was regulated by optimizing the interaction of parameters that influence the enzymatic degradation of P(3HB) film using response surface methodology (RSM). The RSM model was experimentally validated yielding a maximum 21 % weight loss, which represents onefold increment in percentage weight loss in comparison with the conventional method. By using the optimized condition, the enzymatic degradation by an extracellular PHA depolymerase from Acidovorax sp. DP5 was studied at 37 °C and pH 9.0 on different types of PHA films with various monomer compositions. Surface modification of scaffold was employed using enzymatic technique to create highly porous scaffold with a large surface to volume ratio, which makes them attractive as potential tissue scaffold in biomedical field. Scanning electron microscopy revealed that the surface of salt-leached films was more porous compared with the solvent-cast films, and hence, increased the degradation rate of salt-leached films. Apparently, enzymatic degradation behaviors of PHA films were determined by several factors such as monomer composition, crystallinity, molecular weight, porosity, and roughness of the surface. The hydrophilicity and water uptake of degraded salt-leached film of P(3HB-co-70%4HB) were enhanced by incorporating chitosan or alginate. Salt-leached technique followed by partial enzymatic degradation would enhance the cell attachment and suitable for biomedical as a scaffold.     

Investigation of the degradation behaviour of poly(ethylene glycol-co-d,l-lactide) copolymer

The aim was to investigate the degradation behaviour of poly(ethylene glycol-co-d,l-lactide) (PEG-d,l-PLA) multiblock copolymer, in bulk and as microspheres, in aqueous medium. The degradation behaviour of PLA homopolymers in bulk and microspheres was evaluated as comparison.Microsphere preparation was performed by the double emulsion solvent evaporation method. Physical-chemical characterization of the raw polymers and the microspheres was performed by nuclear magnetic resonance (NMR) and modulated differential scanning calorimetry (MDSC). Polymer molecular weight, before and after incubation in aqueous environment, was evaluated by GPC; water uptake and mass loss were determined gravimetrically.The presence of PEG segments inside PLA chains gave a characteristic spongy structure to the microspheres. A significant increase in polymer T_g values was found for the microsphere formulations compared to polymer in bulk. After 63 days of incubation in the aqueous environment, the PEG-d,l-PLA microspheres achieved an average M_w reduction of 47% compared to 20% for PLA microspheres. The corresponding M_w decrease of the polymers in bulk was significantly higher: 72% and 41% for PEG-d,l-PLA and PLA, respectively.The data show how the degradation behaviour of polymer in bulk in an aqueous environment is significantly different from the behaviour of the corresponding microspheres. These results highlight the importance of performing a thorough physical-chemical characterization on microsphere formulations.     

Biodegradation of sequentially surface treated lignocellulose reinforced polylactic acid composites: Carbon dioxide evolution and morphology

Maple fibres were treated with a variety of sequential treatments, namely sodium hydroxide (NaOH), NaOH followed by acetylation, or NaOH followed by silanation. These fibres were incorporated into a polylactic acid (PLA) composite and the biodegradation effects were investigated. After 124 days, all composites had exceeded 90% biodegradation with most close to 100%. The PLA composite with the NaOH-treated fibres had the quickest onset of degradation (4.9 days) and highest peak rate of degradation (1.77% biodegradation/day) of all composites studied. Neat PLA had a similarly high peak rate of degradation at 1.85% biodegradation/day, but had a later onset of 11 days. Gel permeation chromatography (GPC) analysis showed the earlier onset of degradation of the composites was caused by increased hydrolysis during composite fabrication as well as composting. GPC showed the formation of up to three molecular weight bands in the PLA during composting which were hypothesised to be occurring by surface hydrolysis, bulk hydrolysis and hydrolysis at the fibre interface. Analysing the remaining composite revealed the NaOH treatment not only caused an increased rate of degradation in the PLA through increase fibre porosity, but also caused an increased rate of degradation in the fibre from the lack of surface waxes and hemicellulose. Similar, yet slower, behaviours were also seen in the NaOH followed by acetylation and NaOH followed by silane treated composites with all composites degrading more rapidly than the neat PLA and neat maple fibre samples.     

In Vivo Degradation Behavior of Porous Composite Scaffolds of Poly（lactide-co-glycolide） and Nano-hydroxyapatite Surface Grafted with Poly（L-lactide）

The biodegradable porous composite scaffold, composed of poly(lactide-co-glycolide)(PLGA) and hydroxyapatite nanoparticles(n-HAP) surface-grafted with poly(L-lactide)(PLLA)(g-HAP)(g-HAP/PLGA), was fabricated using the solvent casting/particulate leaching method, and its in vivo degradation behavior was investigated by the intramuscular implantation in rabbits. The composite of un-grafted n-HAP/PLGA and neat PLGA were used as controls. The scaffolds had interconnected pore structures with average pore sizes between 137 μm and 148 μm and porosities between 83% and 86%. There was no significant difference in the pore size and porosity among the three scaffolds. Compared with n-HAP/PLGA, the thermo-degradation temperature(Tc) of g-HAP/PLGA decreased while its glass transition temperature(Tg) increased. The weight change, grey value analysis of radiographs and SEM observation showed that the composite scaffolds of g-HAP/PLGA and n-HAP/PLGA showed slower degradation and higher mineralization than the pure PLGA scaffold after the intramuscular implantation. The rapid degradation of PLGA, g-HAP/PLGA and n-HAP/PLGA occurred at 8–12 weeks, 12–16 weeks and 16–20 weeks, respectively. Compared with n-HAP/PLGA, g-HAP/PLGA showed an improved absorption and biomineralization property mostly because of its improved distribution of HAP nanoparticles. The levels of both calcium and phosphorous in serum and urine could be affected to some extent at 3–4 weeks after the implantation of g-HAP/PLGA, but the biochemical detection of serum AST, ALT, ALP, and GGT as well as BUN and CRE showed no obvious influence on the functions of liver and kidney.     

Activated carbon fibers with a high heteroatom content by chemical activation of PBO with phosphoric acid

The preparation of activated carbon fibers (ACFs) by phosphoric acid activation of poly(p-phenylene benzobisoxazole) (PBO) fibers was studied, with particular attention to the effects of impregnation ratio and carbonization temperature on porous texture. Phosphoric acid has a strong effect on PBO degradation, lowering the temperature range at which the decomposition takes place and changing the number of mass loss steps. Chemical analysis results indicated that activation with phosphoric acid increases the concentration of oxygenated surface groups; the resulting materials also exhibiting high nitrogen content. ACFs are obtained with extremely high yields; they have well-developed porosity restricted to the micropore and narrow mesopore range and with a significant concentration of phosphorus incorporated homogeneously in the form of functional groups. An increase in the impregnation ratio leads to increases in both pore volume and pore size, maximum values of surface area (1250 m(2)/g) and total pore volume (0.67 cm(3)/g) being attained at the highest impregnation ratio (210 wt % H(3)PO(4)) and lowest activation temperature (650 °C) used; the corresponding yield was as large as 83 wt %. The obtained surface areas and pore volumes were higher than those achieved in previous works by physical activation with CO(2) of PBO chars.     

Preparation of Organic-Inorganic Composite Adsorbent Beads for Removal of Radionuclides and Heavy Metal Ions

Composite ion exchanger beads were prepared to remove the strontium and silver ions in acidic solution. Potassium titanate and nickelferrocyanate powder, which are acid resistant inorganic ion exchangers were synthesized and then mixed with polyacrylonitrile (PAN) binder to form a PAN-potassium titanate and a PAN-nickelferrocyanate composite ion exchanger beads. Spherical composite beads could be obtained by adjusting the viscosities of the composite dope in the range of 700–1000 cP. The composite beads porosities such as macropore volume and pore size were increased in proportion to the contents of PVP (polyvinylpyrrolidone) which was used as the porosity modifying chemical. The synthesized composite ion exchangers were evaluated on their adsorption characteristics for the Ag¹ and Sr²¹ ion solutions of pH 2.     

块状壳聚糖多孔支架内交替浸渍沉积磷灰石层

在聚合物支架内沉积羟基磷灰石涂层有望提高支架的生物活性和骨传导性. 本研究采用交替浸渍沉积法, 以块状壳聚糖(Cs)三维多孔支架为沉积模板, 在氯化钙溶液和磷酸氢二钠溶液中交替浸渍, 沉积了羟基磷灰石(HA)涂层. 应用XRD、FT-IR、SEM、孔隙率测试、焙烧法和压缩实验对沉积前后支架的组成、形貌、孔隙率、无机物沉积量以及压缩强度进行了表征. 研究结果表明, 支架上沉积物为低结晶度的碳酸羟基磷灰石, 沿c轴择优生长, 与天然骨中磷灰石类似. 扫描电镜照片显示, 磷灰石在支架孔壁上的沉积量呈梯度分布, 外部沉积量多于内部, 靠近支架表面孔隙部分堵塞, 但内部仍保持连通的孔隙结构. 经6次交替浸渍处理的支架, 孔隙率为94.0%, 羟基磷灰石沉积量达到总质量的13.5%, 压缩强度则由0.055 MPa提高到0.109 MPa.     

In vitro degradation and release behavior of porous poly(lactic acid) scaffolds containing chitosan microspheres as a carrier for BMP-2-derived synthetic peptide

To develop a novel tissue engineering scaffold with the capability of controlled releasing BMP-2-derived synthetic peptide, porous poly(lactic acid)/chitosan microspheres (PLA/CMs) composites containing different quantities of chitosan microspheres were prepared by a thermally induced phase separation method. FTIR analysis revealed that there were strong hydrogen bond interactions between the PLA and chitosan component. Introduction of less than 30% CMs (on PLA weight basis) did not remarkably affect the morphology and porosity of the PLA/CMs scaffolds. The compressive strength of the composite scaffolds increased from 0.48 to 0.66 MPa, while the compressive modulus increased from 7.29 to 8.23 MPa as the microspheres' contents increased from 0% to 50%. In vitro degradability investigation indicated that the dissolution of chitosan component was preferential than PLA matrix and the inclusion of CMs could neutralize the acidity of PLA degradation products. Compared with the rapid release from CMs, the synthetic peptide was released from PLA/CMs scaffolds in a temporally controlled manner, mainly depending on the degradation of PLA matrix. The promising microspheres based scaffold release system can be used to deliver bioactive factors for a variety of non-loaded bone regeneration and tissue engineering application.     

Photo-crosslinking copolymers based polyanhydride and 1G polyamidoamine-methacrylamide as bone tissue engineering: Synthesis, characterization, and in vitro degradation

In the past decade, Biodegradable materials that are capable of in situ formation have attracted increased attention for use in restorative orthopedic devices. In this communication, the surface erosion biodegradable polymers derived from 1.0G-polyamidoamine-double bond (PAMAM-DB) and methacrylated sebacic anhydrides (MSA) were evaluated over 2 months period under physiological conditions. Rectangular shaped samples were prepared by crosslinking the components using both chemical and photo initiators and exposure to UV light. The effects of PAMAM-DB: MSA ratio on local pH, water uptake, mass loss, and mechanical properties were explored. Polymers were characterized by ¹H NMR, ¹³C NMR, FT-IR, compressive strength testing and SEM. It is found that copolymer with 50-60% PAMAM-DB (mass fraction) show more excellent mechanical properties compared with other formulations. Copolymers degraded mainly by surface erosion but the bulk erosion pattern also appeared at the initial time of degradation for formulation 30% and 40%. The material was expected to be useful for drug controlled delivery, tissue engineering scaffold and other biomedical applications.     

Hydrolytic Degradation of Polylactic Acid Fibers as a Function of pH and Exposure Time

Polylactic acid (PLA) is a widely used bioresorbable polymer in medical devices owing to its biocompatibility, bioresorbability, and biodegradability. It is also considered a sustainable solution for a wide variety of other applications, including packaging. Because of its widespread use, there have been many studies evaluating this polymer. However, gaps still exist in our understanding of the hydrolytic degradation in extreme pH environments and its impact on physical and mechanical properties, especially in fibrous materials. The goal of this work is to explore the hydrolytic degradation of PLA fibers as a function of a wide range of pH values and exposure times. To complement the experimental measurements, molecular-level details were obtained using both molecular dynamics (MD) simulations with ReaxFF and density functional theory (DFT) calculations. The hydrolytic degradation of PLA fibers from both experiments and simulations was observed to have a faster rate of degradation in alkaline conditions, with 40% of strength loss of the fibers in just 25 days together with an increase in the percent crystallinity of the degraded samples. Additionally, surface erosion was observed in these PLA fibers, especially in extreme alkaline environments, in contrast to bulk erosion observed in molded PLA grafts and other materials, which is attributed to the increased crystallinity induced during the fiber spinning process. These results indicate that spun PLA fibers function in a predictable manner as a bioresorbable medical device when totally degraded at end-of-life in more alkaline conditions.     

Studies on Surface Properties and Cell Adhesion Properties of BSA Modified DBM Scaffold

As a scaffold material for bone tissue engineering, demineralized bone matrix(DBM) has such a limited ability to load cells and growth factors that the surface of the DBM scaffold was modified with bovine serum albumin(BSA) with different concentrations to improve the protein stmcture and physicochemical properties of the scaffold surface so as to enhance the adhesion of the cells. And the appropriate BSA concentration was explored. Compared with DBM, the scaffold with BSA coating had a smaller pore size and a lower porosity, also, the degradation rate was accelerated and the hydrophilic property was improved. Cells adhesion was observed inside the DBM seaffold before and after it had been modified, and the BSA modified scaffold had a good cell compatibility. Wlien the concentration of BSA was 20 mg/mL, the adhesion ability of the cells to modified scaffold was significantly increased, and the cell proliferation was facilitated.     

Poly(l,l-lactide-co-glycolide)/tricalcium phosphate composite scaffold and its various changes during degradation in vitro

A poly(l,l-lactide-co-glycolide) (70/30)/(tricalcium phosphate) (PLGA/TCP) composite scaffold was fabricated by low-temperature deposition (LDM) and its degradation performed in vitro for 22 weeks. Various changes during degradation in vitro, which included changes in acidity of the degradation medium, morphology, weight, composition, molecular weight of the PLGA component and mechanical properties of the scaffold, were investigated. It was found that the acidity of degradation medium of the PLGA(70/30)/TCP composite scaffolds reduced and became much lower than that of TCP-free scaffold. With degradation, the volume and porosity of the PLGA(70/30)/TCP composite scaffold reduced at first then increased slowly, while the surface morphology of the scaffold changed from smooth to rough. The weight loss of the scaffold increased by dissolution of the degraded products and TCP component, but mainly by dissolution of the glycyl-rich degraded products of the PLGA component. The molecular weight of the PLGA component reduced with time, but the molecular weight distribution increased at first and then reduced. The compressive strength and modulus of the scaffold increased at first and then reduced with further degradation. The effect of degradation on modulus was much bigger than that on compressive strength. Based on excellent cell affinity of the PLGA(70/30)/TCP composite scaffold, a potentially useful bone tissue engineering scaffold is proposed.     

纳米细菌纤维素膜的表征与生物相容性研究

利用木醋杆菌静态培养法制备的由纳米纤维组成的细菌纤维素膜具有超细的三维网络结构和适当的孔隙率. 利用光镜、扫描电镜和原子力显微镜对其进行结构表征发现, 细菌纤维素膜具有极为精细的纳米网络结构, 冻干膜的孔径约为0.6~2.8 μm; 纤维素带宽度约为50~80 nm. 采用湿重与浮重结合法测定烘干膜和冻干膜的孔隙率分别约为70%和90%. 由于细菌纤维素含有大量的羟基, 故烘干膜表现出极好的透湿性. 将细菌纤维素膜分别与成纤维细胞和软骨细胞进行复合培养, 并将成纤维细胞和细菌纤维素膜的复合物进行裸鼠皮下移植实验. 结果显示, 移植的复合物很好地融入了裸鼠正常皮肤, 成纤维细胞和软骨细胞在细菌纤维素表面形成连续的细胞层, 绿色荧光蛋白表达正常. 以上结果表明, 细菌纤维素膜非常适合细胞贴附和增殖, 表现出较好的生物相容性, 有望成为新型组织工程支架材料.     

Mesopore structure of microcrystalline cellulose tablets characterized by nitrogen adsorption and SEM: the influence on water-induced ionic conduction

Tablets of microcrystalline cellulose were formed at different compaction pressures and physical properties, such as pore size distribution, surface area, and pore surface fractality, were extracted from N2 adsorption isotherms. These properties were compared to previously published data on the water-induced ionic conductivity of the tablets. The conduction process was shown to follow a percolation model with a percolation exponent of 2 and a porosity percolation threshold of approximately 0.1. The critical pore diameter for facilitated charge transport was shown to be in the 5-20 nm range. When the network of pores with a diameter in this interval is reduced to the point where it no longer forms a continuous passageway throughout the compact, the conduction process is dominated by charge transport on the surfaces of individual microfibrils mainly situated in the bulk of fibril aggregates. A fractal analysis of nitrogen adsorption isotherms showed that the dominant interface forces during adsorption is attributed to surface tensions between the gas and the adsorbed liquid phase. The extracted fractal dimension of the analyzed pore surfaces remained unaffected by the densification process at low compaction pressures (< approximately 200 MPa). At increased densification, however, pore-surface structures smaller than approximately 100 nm become smoother as the fractal dimension decreases from approximately 2.5 at high porosities to approximately 2.3 for the densest tablets under study.