Color Change of Electrospun Polystyrene/MEH‐PPV Fibers from Orange to Yellow through Partial Decomposition of MEH Side Groups

The present contribution reports the electrospinning of PS/MEH‐PPV fibers with average diameters ranging from 0.165 to 1.190 µm from solutions of PS/MEH‐PPV (PS/MEH‐PPV = 7.5:1, w/w) in 1,2‐dichloroethane. With the addition of pyridinium formate (PF), a volatile organic salt, to the PS/MEH‐PPV solution, the electrospinnability of the resulting solution is enhanced significantly. Both the fiber diameters and the number of fibers are found to increase, while the number of beads is found to decrease with increasing applied electrical potential, the addition of PF, and increasing aging period of the spinning solution after PF addition. FT‐IR analysis shows that ≈15% of the MEH side groups are removed from the MEH‐PPV component in the fibers obtained from the solution that is left to age for 1 month after PF addition, which corresponds well to the loss of mass of ≈7% as observed by thermogravimetric analysis. As a result, partial decomposition of the MEH side groups should be responsible for the observed yellow emission color of the PS/MEH‐PPV fibers obtained from the same solution.

     

Polymer‐Based Rectifying Diodes on a Glass Substrate Fabricated by Ink‐Jet Printing

Summary: The fabrication of polymer diodes on a glass substrate by an ink‐jet printing technique is reported. Both an n‐type semiconductive polymer, poly[2‐methoxy‐5‐(2‐ethylhexyloxy)‐1,4‐(1‐cyanovinylene)phenylene] (CN‐PPV), and a p‐type semiconductive polymer, polypyrrole (PPy) or poly(3,4‐ethylenedioxythiophene) (PEDOT), were printed through a piezoelectric ink‐jet printer. The printed CN‐PPV/PPy and CN‐PPV/PEDOT diodes showed good rectifying characteristics. These results indicate the potential of the low‐cost ink‐jet printing technique to produce polymer microelectronic devices and circuits.

Schematic diagram of the printed polymer diode     

Synthesis and Fluorescent Properties of Biodegradable Hyperbranched Poly(amido amine)s

Disulfide‐functionalized hyperbranched poly(amido amine)s (HPAMAMs) were synthesized by Michael addition polymerization of N,N'‐cystaminebisacrylamide and 1‐(2‐aminoethyl)piperazine. The novel HPAMAMs displayed bright fluorescence, and the emissions bands cover nearly the whole visible wavelength range. When polymer solutions were excited at 330–385, 460–490, and 510–550 nm, blue, green, and red solutions were observed, respectively. The HPAMAMs are biodegradable and they can be easily cleaved by 2‐mercaptoethanol or glutathione, leading to a decrease in the fluorescence intensity. Studies of applications of the biocompatible and biodegradable HPAMAMs in fluorescence imaging technology and biological science are in progress.

     

Preparation of a Rapidly Forming Poly(ferrocenylsilane)‐Poly(ethylene glycol)‐based Hydrogel by a Thiol‐Michael Addition Click Reaction

The synthesis of a rapidly forming redox responsive poly(ferrocenylsilane)‐poly(ethylene glycol) (PFS‐PEG)‐based hydrogel is described, achieved by a thiol‐Michael addition click reaction. PFS bearing acrylate side groups (PFS‐acryl) was synthesized by side group modification of poly(ferrocenyl(3‐iodopropyl)methylsilane) (PFS‐I) and characterized by ¹H NMR, ¹³C NMR, and FT‐IR spectroscopy. The equilibrium swelling ratio, morphology, rheology, and redox responsive properties of the PFS‐PEG‐based hydrogel are reported.

     

Spontaneous Ring‐Opening Polymerization of Macrocyclic Aromatic Thioether Ketones under Transient High‐Temperature Conditions

Summary: Spontaneous ring‐opening polymerization of macrocyclic aromatic thioether ketones [ 1,4‐SC₆H₄COC₆H₄ ]_n (n = 3 and 4), in which the thioether linkages are para to the ketone, occurs during rapid, transient heating to 480 °C, to afford a soluble, semi‐crystalline poly(thioether ketone) of high molar mass (η_inh > 1.0 dL · g⁻¹). Corresponding macrocyclic ether ketones, and a macrocyclic thioether ether ketone in which the thioether linkage is para to the ether rather than to the ketone, show no evidence of polymerization under analogous conditions.

The uncatalysed ring‐opening polymerization of macrocycle 1 , within the pores of an alumina microfiltration membrane, leads to formation of polymer 3 with the microstructure shown in the above scanning electron micrograph.     

Poly(para‐phenylene vinylene) and Polynorbornadiene Containing Rod‐Coil Block Copoylmers via Combination of Acyclic Diene Metathesis and Ring‐Opening Metathesis Polymerization

Poly(para‐phenylene vinylene) (PPV) and its derivatives are important semiconducting polymers for organic electronics. Herein, an alkene metathesis approach to obtain PPVs is reported. Tri(iso propyl)silyl‐substituted norbornadienes are employed as solubilizing agents. As PPV precursors divinylbenzene is used for acyclic diene metathesis and paracyclophane diene for a ring‐opening metathesis polymerization‐type approach. The resulting polymers are analyzed by gel permeation chromatography (GPC), UV‐vis, fluorescence, and nuclear magnetic resonance (NMR) spectroscopy. All of the polymers show good solubility in common solvents.

     

Fabrication of Highly Photoluminescent TiO2/PPV Hybrid Nanoparticle‐Polymer Fibers by Electrospinning

In this study, we have synthesized highly photoluminescent TiO₂/poly (phenylene vinylene) (PPV) hybrid nanoparticle‐polymer fibers by electrospinning a PPV precursor added to a TiO₂ sol‐gel solution. The diameters of the hybrid fibers ranged from 100–300 nm and the average size of TiO₂ nanoparticles within the fibers was 10–60 nm. FT‐IR analysis indicated that a new band around 1 632 cm⁻¹ assigned to the Ti O C vibration appeared, which resulted in the stronger luminance of the fluorescence of the TiO₂/PPV hybrid fibers compared to free standing PPV nanofibers.

     

Synthesis of Crosslinked Sulfonated Poly(phenylene sulfide sulfone nitrile) for Direct Methanol Fuel Cell Applications

With a view towards direct methanol fuel cell applications, novel sulfonated poly(phenylene sulfide sulfone nitrile) (sPPSSfN) has been prepared and subsequently crosslinked by a Friedel‐Craft reaction using 4,4′‐oxybis(benzoic acid) as a crosslinker to achieve lower water swelling and lower methanol permeability. The dimensional change of SPPSSfN40 is 43.7% in 90 °C liquid water but that of the crosslinked membrane, XsPPSSfN40, is 23.3% while maintaining proton conductivity at 0.22 S · cm⁻¹. These results show that the Friedel‐Craft crosslinking of the novel sPPSSfN membrane effectively reduces water uptake and the degree of swelling while improving the dimensional stability and maintaining high proton conductivity.

     

Preparation of Binary Conductive Polymer Composites with Very Low Percolation Threshold by Latex Blending

The communication reports a way to prepare carbon black (CB)/waterborne polyurethane conducting composites with percolation thresholds as low as 0.2 vol.‐% through conventional latex blending. CB particles in the composites appear segregated in their distribution and are located in the two‐dimensional interstices among the polymer domains. The intimate filler/matrix interaction also improves the tensile strength of the matrix at the CB content corresponding to the electrical percolation threshold.

Room temperature conductivity, σ, and tensile strength as a function of carbon black (CB) concentration of the waterborne‐polyurethane‐based composites prepared by latex blending.     

Predicting the Change of MWD Caused by Interchange Reactions During Melt‐Mixing of Linear and Branched Polycondensates (AB2)

During mix melting of hyperbranched AB₂‐ and linear CD‐polycondensates distributive properties are changing by interchange reactions. Two mathematical modeling approaches are presented: (i) Simplified approach of monodisperse population of three‐arm stars undergoing interchange reactions, both analytical and by Monte Carlo simulations, assuming interchange as subsequent scission and recombination of fragments. (ii) Full system of interchange and polycondensation/hydrolysis reactions with Monte Carlo simulations and kinetic model describing reactions of free groups (A, B, C, D) and bonds (AB, CD, BC, AD). MC simulations show that the final molecular weight and branching distribution is attained after 10% of reaction time. The change of structure, from few large fragments to more, smaller ones, is slower.

     

Synthesis,Photophysics, and Electroluminescence of Poly(dibenzofluorene)s

Summary: A series of soluble poly(dibenzofluorene) derivatives that contain dibenzo[a,g]fluorene, dibenzo[a,i]fluorene, and dibenzo[c,g]fluorene repeat units in the main chain have been synthesized, characterized, and explored as emissive materials in polymer light emitting diodes (PLEDs). These polymers possess higher glass transition temperatures (108–133 °C) than that of poly(2,7‐(9,9‐dialkyl)fluorene) (PFO). The photophysical and electrochemical properties of these polymers are affected by the steric hindrance effect. These polymers emit blue light in dilute solution (378–400 nm) and in the solid state (426–447 nm). As emissive materials in PLEDs, blue electroluminescence with a brightness of up to 3 130 cd · m⁻² is obtained from single‐layer diodes of P₂ with aluminum/barium in air.

The photophysical and electrochemical properties of these polymers are affected by the size effect.     

Mechanistic Investigation into the Unique Orientation Textures of Poly(vinylidene fluoride) in Blends with Nylon 11

Self‐seeded crystallization experiments were carried out to detect the mechanism of the unique orientation behavior of poly(vinylidene fluoride) (PVDF) in oriented PVDF/nylon 11 blends. It was found that primary nuclei have no effects on the final orientation textures adopted by PVDF. The results show that the PVDF crystal orientation in the oriented blends is determined in the early stage of crystal growth, thus a trans crystallization mechanism is preferred.

Isothermal crystallization kinetics for the self‐seeded and non‐self‐seeded crystallization at 145 °C.     

Supramolecular Nanocycles Comprising β‐Cyclodextrin‐click‐Ferrocene Units: Rings of Rings of Rings

We applied 1,3‐dipolar cycloaddition to bind ethynylferrocene onto 6I‐azido‐6I‐deoxycyclomaltoheptaose under microwave assisted conditions. The process was investigated by ¹H NMR, FT‐IR spectroscopy, and MALDI‐TOF mass spectrometry. The ability of the synthesized compound to self‐organize to cyclic supramolecular structures was investigated by dynamic light scattering measurements and cryo‐transmission electron microscopy.

     

Hetero Diels–Alder Chemistry for the Functionalization of Single‐Walled Carbon Nanotubes with Cyclopentadienyl End‐Capped Polymer Strands

Single‐walled carbon nanotubes (SWCNTs) are pre‐functionalized with a pyridinyl‐based dithioester to undergo a hetero Diels–Alder (HDA) reaction with cyclopentadienyl end‐capped poly(methyl)methacrylate (M _n = 2700 g mol⁻¹, PDI = 1.14). Fourier transform infrared spectroscopy, thermogravimetric analysis, elemental analysis (EA), and X‐ray photoelectron spectroscopy (XPS) evidence the success of the grafting process. The estimated resulting grafting density (from XPS and EA) via the HDA reaction increases by a factor of more than two (0.0774 chains·nm⁻² via XPS) compared with typical values obtained via a direct cyclopentadiene driven Diels–Alder conjugation onto non‐functional SWCNTs under similar conditions.

     

Cross‐Linked Alq3‐Containing Polymers with Improved Electroluminescence Efficiency Used for OLEDs

Summary: Homopolymers and a series of copolymers with tris‐8‐hydroxyquinoline aluminum (Alq₃) as the cross‐links are synthesized. All these polymers show improved electroluminescence (EL) efficiency over their previously reported counterparts. Among them, the copolymers containing Alq₃ and carbazole groups show higher EL efficiency than that of the homopolymers. We also demonstrate the feasibility of generating patterns using the homopolymers via photopolymerization. The cross‐linked nature, selectivity of patterning, high thermal stability, and EL efficiency might render these polymers a promising material in fabricating large‐scaled multilayered sub‐pixellation organic light‐emitting diodes (OLEDs).

Current–voltage and the electroluminescence–voltage curve of two‐layer devices for the Alq₃‐homopolymers and the Alq₃‐copolymers (luminance is shown by the symbols without lines).     

Nickel(II) α‐Diimine Catalyst for Grignard Metathesis (GRIM) Polymerization

A nickel α‐diimine catalyst was used for Grignard metathesis (GRIM) polymerization of 2,5‐dibromo 3‐hexylthiophene and 2‐bromo‐5‐iodo‐3‐hexylthiophene monomers. GRIM polymerization of 2‐bromo‐5‐iodo‐3‐hexylthiophene generated regioregular polymers with molecular weights ranging from 3 000 to 12 000 g · mol⁻¹. The nickel α‐diimine catalyst was also successfully used for the GRIM polymerization of a bulky benzodithiophene monomer.

     

Rheology and Physical Properties of Polyethylene/Polyethylene‐Ionomer Blends and their Clay Nanocomposites

Rheological and solid‐state physical properties of blends containing high‐density polyethylene (HDPE) and a polyampholyte derivative (PE‐g‐PA) are assessed along with their onium ion‐exchanged montmorillonite clay (NR‐MM) nanocomposites. Strong deviations from the log‐additivity rule of zero‐shear viscosity, combined with synergistic behavior in tensile moduli, are consistent with a multi‐phase blend morphology. While this affects clay dispersion in filled blends, PE‐g‐PA/HDPE based nanocomposites are shown to exhibit a favorable balance between material stiffness and ductility.

     

A Cationic Water‐Soluble Poly(p‐phenylenevinylene) Derivative: Highly Sensitive Biosensor for Iron‐Sulfur Protein Detection

Summary: A new water‐soluble cationic ammonium‐functionalized poly(p‐phenylenevinylene) (PPV‐NEtMe) was successfully synthesized and exhibited high sensitivity (K_sv = 6.9 × 10⁷ M ⁻¹) on rubredoxin, a type of anionic iron‐sulfur (Fe‐S) proteins. Further investigation showed that the biosensitivity of the cationic conjugated polymer is strongly dependent on the nature of the buffer solution and the concentration of the conjugated polymer used in the analyses.

The schematic diagram of anionic rubredoxin detected by PPV‐NEtMe.     

A Closed‐Loop Phase Diagram in a Weakly Interacting Polyolefin Copolymer Binary Blend System

Summary: The phase behavior of poly(ethylene‐co‐styrene) (PES) and poly(ethylene‐co‐butene) (PEB) blends has been studied. A closed‐loop phase diagram was clearly observed in this weakly interacting system as the styrene content in the PES decreased to about 1 mol‐%. At higher styrene contents, the phase loop starts to interplay with the crystallization transformation at lower temperatures.

Phase diagram of PEB/PES blends. Phase boundary line is only for easy demonstration.     

Polymers that Contain Ligated Metals in their Side Chain: Building a Foundation for Functional Materials in Opto‐Electronic Applications with an Emphasis on Lanthanide Ions

Organic polymers that contain ligated metals offer a variety of unique properties which include luminescence, electro‐ and photochemistry, catalysis, charge, magnetism, and thermochromism. These organic–inorganic hybrid materials have the potential to offer novel active matrixes for advanced devices. Continued progress in synthetic chemistry and molecular characterization will enable such advanced materials. Here the focus is restricted to side‐chain metal complexes with emissive properties that highlight the use of lanthanide ions as opposed to the often‐studied transition metal complexes.