Poly(methyl silsesquioxane)/amphiphilic block copolymer hybrids and their porous derivatives: Poly(styrene‐block‐acrylic acid) and poly(styrene‐block‐3‐trimethoxysilylpropyl methacrylate)

Porous poly(methyl silsesquioxane) (PMSSQ) films were prepared from PMSSQ/amphiphilic block copolymer (ABC) hybrids, and this was followed by spin coating and multistep baking. The ABCs were poly(styrene‐block‐acrylic acid) (PS‐b‐PAA) and poly(styrene‐block‐3‐trimethoxysilylpropyl methacrylate) (PS‐b‐PMSMA), which were synthesized by living polymerization. The chemical bonding between the ABCs and PMSSQ resulted in significant differences in the morphologies and properties of the hybrids and their porous derivatives. Both intramolecular and intermolecular hydrogen bonding existed in the PMSSQ/PS‐b‐PAA hybrid and led to macrophase separation. Through the modification of the chemical structure from the poly(acrylic acid) segment to PMSMA, covalent bonding between PMSSQ and PMSMA occurred and prevented the macrophase separation and initial pyrolysis of the ABC. Modulated differential scanning calorimetry results also suggested a significant difference in the miscibility of the two hybrid systems. The chemical bonding resulted in higher retardation of the symmetry‐to‐nonsymmetry Si? O? Si structural transformation for PMSSQ/PS‐b‐PMSMA than for PMSSQ/PS‐b‐PAA according to Fourier transform infrared studies. The pore size of the nanoporous thin film from the PMSSQ/PS‐b‐PMSMA hybrid was estimated by transmission electron microscopy to be less than 15 nm. The refractive index and dielectric constant of the prepared porous films decreased from 1.354 to 1.226 and from 2.603 to 1.843 as the PS‐b‐PMSMA loading increased from 0 to 50 wt %, respectively. This study suggests that chemical bonding in hybrid materials plays a significant role in the preparation of low‐dielectric‐constant nanoporous films. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4466–4477, 2004     

Poly(aryl ether ketone)s with (3‐methyl)phenyl and (3‐trifluoromethyl)phenyl side groups

New bisphenol monomers, (3‐methyl)phenylhydroquinone and (3‐trifluoromethyl)phenylhydroquinone, were prepared in a two‐step synthesis. A series of poly(aryl ether ketone)s were derived from these bisphenols via a nucleophilic aromatic substitution polycondensation with various bisfluoro compounds. The polycondensation proceeded quantitatively in tetramethylene sulfone in the presence of anhydrous potassium carbonate and afforded the polymers with inherent viscosities of 0.63–0.91 dL/g. The fluorinated polymers showed lower glass‐transition temperatures and higher thermal‐decomposition temperatures than the corresponding nonfluorinated polymers. The solubility of the polymers was improved by the introduction of bulky pendant groups. All the polymers formed transparent, strong, and flexible films, with tensile strengths of 86.4–102.0 MPa, Young's moduli of 2.28–3.03 GPa, and elongations at break of 14–42%. All the polymers had low dielectric constants of 2.70–2.83 at 1 MHz. Compared with the methylated polymers, the trifluoromethylated polymers exhibited lower water sorption, which was attributed to the stronger hydrophobicity of the fluorine‐containing groups. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3392–3398, 2002     

Poly(methyl methacrylate)/Methacryl-POSS Nanocomposites with Excellent Thermal Properties

Poly(methyl methacrylate) (PMMA) nanocomposites containing (methacryloxy)propyl polyhedral oligomeric silsesquioxane (methacryl‐POSS) were prepared by bulk‐polymerization process. The structures of the products were characterized by FTIR, solid‐state NMR, TEM, XRD, DSC, TGA, XPS and UV‐Vis spectra. The hybrid materials were found to be largely homogeneous. DSC and TGA results indicate that the thermal properties of PMMA nanocomposites are significantly improved. The glass transition temperature (T_g) and thermal decomposition temperature (T_dec) of the nanocomposites increased by 58 and 110°C, respectively. The bulk hybrid material maintains excellent optical transparency in visible region.     

Nanocomposites of Polyaniline/Poly(2‐methoxyaniline‐5‐sulfonic acid)

Summary: Poly(2‐methoxyaniline‐5‐sulfonic acid) (PMAS) is a water‐soluble derivative of polyaniline that carries negatively charged sulfonate groups. This self‐doped conducting polymer also behaves like a polyelectrolyte that can subsequently function as a dopant in polyaniline (PAn). The chemical synthesis of PAn/PMAS is presented describing the preparation of a highly stable composite dispersion. TEM images reveal a mixture of well‐defined nanofibres and nanoparticles with diameters between 20 and 100 nm. The UV‐vis spectra of the PAn/PMAS composite in water and in alkaline media indicate that both PAn and PMAS are present in the composite. Electrochemical studies show that both of the conducting polymer components are capable of undergoing oxidation and reduction. The novel PAn/PMAS nanocomposite has enhanced electrical conductivity and stability compared to PAn/HCl nanofibres prepared under equivalent conditions, making it a promising material for applications in areas such as batteries, electronic textiles, electrochromics, and chemical sensors.

Transmission electron micrograph of a PAn/PMAS nanocomposite.     

A Novel ABC Triblock Copolymer with Very Low Surface Energy: Poly(dimethylsiloxane)‐block‐Poly(methyl methacrylate)‐block‐Poly(2,2,3,3,4,4,4‐heptafluorobutyl methacrylate)

Poly(dimethylsiloxane)‐block‐poly(methyl methacrylate)‐block‐poly(2,2,3,3,4,4,4‐heptafluorobutyl methacrylate) was successfully synthesized via ATRP. The chemical composition and structure of the copolymer was characterized by NMR and FT‐IR spectroscopy and molecular weight measurement. Gel permeation chromatography was used to study the molecular weight distribution of the triblock copolymer. The surface properties of the resulting copolymer were investigated. The effects of fluorine content and bulk structure on surface energy were investigated by static water contact angle measurements. Surface composition was studied by XPS.

     

Emulsion‐Induced Ordered Microporous Films Based on Micelles of Amphiphilic Poly(ethylene oxide)‐block‐Poly(methyl methacrylate) Diblock Copolymers

Well‐defined PEO‐b‐PMMA was prepared, initiated by macroinitiator PEO‐Br, by means of ATRP, where esterification of the terminal hydroxyl group of PEO with 2‐bromoisobutyryl bromide yielded a macroinitiator PEO‐Br. Highly ordered microporous films (hexagonal pattern) were constructed by emulsion micelles of such amphiphilic diblock copolymer formed from a solution with CHCl₃/H₂O/THF = 100:5:10 (v/v). We also constructed the microporous films using diblock copolymer by the current water‐assisted method.

     

Synthesis and characterization of poly(methyl methacrylate)‐block‐poly(methylphenylsilane)‐ block‐poly(methyl methacrylate) by atom transfer radical polymerization

ABA block copolymers of methyl methacrylate and methylphenylsilane were synthesized with a methodology based on atom transfer radical polymerization (ATRP). The reaction of samples of α,ω‐dihalopoly(methylphenylsilane) with 2‐hydroxyethyl‐2‐methyl‐2‐bromoproprionate gave suitable macroinitiators for the ATRP of methyl methacrylate. The latter procedure was carried out at 95 °C in a xylene solution with CuBr and 2,2‐bipyridine as the initiating system. The rate of the polymerization was first‐order with respect to monomer conversion. The block copolymers were characterized with ¹H NMR and ¹³C NMR spectroscopy and size exclusion chromatography, and differential scanning calorimetry was used to obtain preliminary evidence of phase separation in the copolymer products. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 30–40, 2003     

树状大分子/金属（化合物）纳米复合材料*

本文综述了一类新的有机/无机杂化材料——树状大分子/金属（化合物）纳米复合材料的研究进展。该杂化纳米材料由树状大分子内或树状大分子间螯合金属离子通过还原生成相应的零价金属纳米粒子或与阴离子反应生成金属化合物的方法制备。其中树状大分子内复合物粒子体积与原树状大分子内负载的金属离子数量有关,树状大分子间复合物粒子体积与树状大分子的浓度和代数有关。     

Electrochemical Treatment for Effectively Tuning Thermoelectric Properties of Free‐Standing Poly(3‐methylthiophene) Films

The degree of oxidation of conducting polymers has great influence on their thermoelectric properties. Free‐standing poly(3‐methylthiophene) (P3MeT) films were prepared by electrochemical polymerization in boron trifluoride diethyl etherate, and the fresh films were treated electrochemically with a solution of propylene carbonate/lithium perchlorate as mediator. The conductivity of the resultant P3MeT films depends on the doping level, which is controlled by a constant potential from ?0.5 to 1.4 V. The optimum electrical conductivity (78.9 S cm^?1 at 0.5 V) and a significant increase in the Seebeck coefficient (64.3 μV K^?1 at ?0.5 V) are important for achieving an optimum power factor at an optimal potential. The power factor of electrochemically treated P3MeT films reached its maximum value of 4.03 μW m^?1 K^?2 at 0.5 V. Moreover, after two months, it still exhibited a value of 3.75 μW m^?1 K^?2, and thus was more stable than pristine P3MeT due to exchange of doping ions in films under ambient conditions. This electrochemical treatment is a significant alternative method for optimizing the thermoelectric power factor of conducting polymer films.     

Chemical‐Bonding‐Directed Hierarchical Assembly of Nanoribbon‐Shaped Nanocomposites of Gold Nanorods and Poly(3‐hexylthiophene)

Nanoribbon‐shaped nanocomposites composed of conjugated polymer poly(3‐hexylthiophene) (P3HT) nanoribbons and plasmonic gold nanorods (AuNRs) were crafted by a co‐assembly of thiol‐terminated P3HT (P3HT‐SH) nanofibers with dodecanethiol‐coated AuNRs (AuNRs‐DDT). First, P3HT‐SH nanofibers were formed due to interchain π–π stacking. Upon the addition of AuNRs‐DDT, P3HT‐SH nanofibers were transformed into nanoribbons decorated with the aligned AuNRs on the surface (i.e., nanoribbon‐like P3HT/AuNRs nanocomposites). Depending on the surface coverage of the P3HT nanoribbons by AuNRs, these hierarchically assembled nanocomposites exhibited broadened and red‐shifted absorption bands of AuNRs in nIR region due to the plasmon coupling of adjacent aligned AuNRs and displayed quenched photoluminescence of P3HT. Such conjugated polymer/plasmonic nanorod nanocomposites may find applications in fields, such as building blocks for complex superstructures, optical biosensors, and optoelectronic devices.     

Suppression of Thermochromism in a Poly(di‐n‐hexylsilane)‐Zirconia Hybrid

Summary: Poly(di‐n‐hexylsilane) (PDHS)‐containing zirconia hybrid thin films were prepared by a sol‐gel reaction of PDHS copolymers and zirconium alkoxide, and it was found that the thermochromic properties of PDHS due to the transformation of the Si Si main chain were suppressed in the PDHS‐zirconia hybrid thin film.

Structure of poly(di‐n‐hexylsilane)‐zirconia hybrid.     

Self‐Assembly of Poly(vinylpyridine‐b‐oligo(ethylene glycol) methyl ether methacrylate) Diblock Copolymers

Poly(oligoethylene glycol)‐poly(2‐vinylpyridine) is a model diblock for studying the effect of block‐localized charge on block copolymer self‐assembly because in the absence of charge the polymers are perfectly miscible, and upon protonation of the vinylpyridine block the polymer undergoes an order–disorder transition. Seven model block copolymers with molecular weights of approximately 60 kDa containing poly(2‐vinylpyridine) volume fractions spanning 0.069–0.700 were synthesized using reversible addition fragmentation transfer polymerization and then studied to understand the effect of protonation level, diblock composition, and temperature on the location of the ordering transition and the type of nanostructures formed in a charge asymmetric system. All of the polymers displayed lower critical solution‐type behavior, with the order–disorder transition temperature decreasing with increasing acid content. Polymers with symmetric compositions showed the highest degree of incompatibility for a given degree of protonation, and the observed morphologies for all polymers were consistent with those observed at similar compositions for classical hydrophobic block copolymers. The observed protonation‐induced phase transition can be explained by the shift of the Flory–Huggins parameter due to the alternation of the identity of monomers, consistent with the prediction of Nakamura and Wang's theory. The use of polyvalent ions promotes self‐assembly at lower concentrations, consistent with ionic crosslinking effects between polymer chains that are promoted at high concentration due to exchange entropy in crosslinked polymers. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 1181–1190     

Synthesis and dielectric properties of photoreactive polystyrene containing [1‐(3‐isopropenyl‐phenyl)‐1‐methyl‐ethyl]‐carbamate in the side chain

Novel polystyrene derivatives comprising [1‐(3‐isopropenyl‐phenyl)‐1‐methyl‐ethyl]‐carbamate in the side chain were synthesized as photoreactive copolymers. Poly(4‐vinylphenol) was made to react with 1‐(1‐isocyanato‐1‐methyl‐ethyl)‐3‐isopropenyl‐benzene (m‐TMI) and the unreacted hydroxyl groups were protected with acetyl chloride. The copolymers are highly sensitive to the radical photoinitiators that can be activated by irradiation of UV light (λ = 300–365 nm). FTIR spectroscopy was employed to monitor the structural changes in the copolymers exposed to UV irradiation. The dielectric properties of the copolymers were investigated by measuring the capacitance and calculating the permittivity as a function of frequency, along with the I–V characteristics. Their properties were compared with those of thermally crosslinkable poly(4‐vinylphenol) blended with poly(melamine‐co‐formaldehyde), which is frequently used as a dielectric layer in organic field‐effect transistors (OFETs). No significant dielectric dispersion was observed in the frequency range of 1 kHz–1 MHz. The dielectric constant was determined to be in the range of 4.2–6.0, which offers a potential for the application of these copolymers to OFET gate insulators. These soluble dielectrics exhibit good film uniformity and can also be patterned using a standard photolithographic technique. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1710–1718, 2008     

Red to Blue High Electrochromic Contrast and Rapid Switching Poly(3,4‐ethylenedioxypyrrole)–Au/Ag Nanocomposite Devices for Smart Windows

Poly(3,4‐ethylenedioxypyrrole) (PEDOP)–Ag and PEDOP–Au nanocomposite films have been synthesized for the first time by electropolymerization of the conducting‐polymer precursor in a waterproof ionic liquid, 1‐butyl‐1‐methylpyrrolidinium bis(trifluoromethylsulfonyl)imide, followed by Ag/Au nanoparticle incorporation. That the Ag/Au nanoparticles are not adventitious entities in the film is confirmed by a) X‐ray photoelectron spectroscopy, which provides evidence of Ag/Au–PEDOP interactions through chemical shifts of the Ag/Au core levels and new signals due to Ag–N(H) and Au–N(H) components, and b) electron microscopy, which reveals Au nanoparticles with a face‐centered‐cubic crystalline structure associated with the amorphous polymer. Spectroelectrochemistry of electrochromic devices based on PEDOP–Au show a large coloring efficiency (η_max=270 cm² C^?1, λ=458 nm) in the visible region, for an orange/red to blue reversible transition, followed by a second, remarkably high η_max of 490 cm² C^?1 (λ=1000 nm) in the near‐infrared region as compared to the much lower values achieved for the neat PEDOP analogue. Electrochemical impedance spectroscopy studies reveal that the metal nanoparticles lower charge‐transfer resistance and facilitate ion intercalation–deintercalation, which manifests in enhanced performance characteristics. In addition, significantly faster color–bleach kinetics (five times of that of neat PEDOP!) and a larger electrochemical ion insertion capacity unambiguously demonstrate the potential such conducting‐polymer nanocomposites have for smart window applications.     

Conductivity of Poly(methyl methacrylate)/Polystyrene/Carbon Black and Poly(ethyl methacrylate)/Polystyrene/Carbon Black Ternary Composite Films

Poly(methyl methacrylate)(PMMA)/polystyrene(PS)/carbon black(CB)and poly(ethyl methacrylate)(PEMA)/PS/CB ternary composite films were obtained using solution casting technique to investigate double percolation effect.In both PMMA/PS/CB and PEMA/PS/CB ternary composite films,the CB particles prefer to locate into PS phase based on the results of calculating wetting coefficient,which is also confirmed by SEM images.The conductivity of the films was investigated,and the percolation threshold(￠c)of both ternary composite films with different polymer blend ratios was determined by fitting the McLachlan GEM equation.Conductivity of PMMA/PS/CB ternary composite films showed a typical double percolation effect.However,due to the double emulsion structure of PEMA/PS polymer blends,the PEMA/PS/CB ternary composite films(PEMA/PS=50/50)showed a higher￠c,even CB only located in PS phase,which conflicts with the double percolation effect.A schematic diagram combined with SEM images was proposed to explain this phenomenon.     

Microstructure and properties of 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA)‐p‐phenylene diamine (PDA) polyimide/poly(vinylsilsesquioxane) hybrid nanocomposite films

Hybrid nanocomposite films of poly(vinylsilsesquioxane) (PVSSQ) and polyimide (PI) (PI/PVSSQ) were prepared via sol‐gel process from triethoxyvinylsilane (VSSQ) and thermal imidization from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA)‐p‐phenylene diamine (PDA) polyamic acid (BPDA‐PDA PAA). We investigated the microstructure; interfacial interaction; and optical, thermal, dielectric, and mechanical properties of the hybrid films. The phase morphologies and degree of surface roughness were evaluated by scanning electron microscope (SEM) and atomic force microscope (AFM), respectively. It was found that the surface topography was influenced by the composition of PVSSQ. Hydrogen bonding interactions between polyimide (PI) matrix and PVSSQ domains were proved with FT‐IR spectroscopy. The transparency of the hybrid films was found to be dependent on the PVSSQ content. Incorporating of the PVSSQ in the hybrid composites increased the glass transition temperature of PI. Dielectric constants of the hybrid films were in the range of 2.37–3.59. Properties of the PI films were also significantly enhanced by adding 5–30 wt % of PVSSQ. For comparison, we also prepared the hybrid composites of PI and mixtures of VSSQ and tetraethoxysilane (TEOS) and the PI/silica hybrid composite containing 30 wt % of silica obtained from TEOS. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5189–5199, 2004     

Waterborne Dispersions of a Polymer‐Encapsulated Inorganic Particle Nanocomposite by Phase‐Inversion Emulsification

Inorganic silica nanoparticles were encapsulated with an epoxy resin to give waterborne nanocomposite dispersions, using the phase‐inversion emulsification technique. Sub‐micron‐sized waterborne particles with narrow size distribution were prepared such. Microscopy results indicate that all the silica nanoparticles are encapsulated within the composites and uniformly dispersed therein. Curing of the nanocomposite dispersions proceeded in a controlled manner.     

Synthesis of Poly(glycidyl methacrylate)‐block‐Poly(pentafluorostyrene) by RAFT: Precursor to Novel Amphiphilic Poly(glyceryl methacrylate)‐block‐Poly(pentafluorostyrene)

Poly(glycidyl methacrylate) (PGMA) was synthesized by the RAFT method in the presence of 2‐cyanoprop‐2‐yl dithiobenzoate (CPDB) chain transfer agent using different [GMA]/[CPDB] molar ratios. The living radical polymerization resulted in controlled molecular weights and narrow polydispersity indices (PDI) of ≈1.1. The polymerization of pentafluorostyrene (PFS) with PGMA as the macro‐RAFT agent yielded narrow PDIs of ≤1.2 at 60 °C and ≤1.5 at 80 °C. The epoxy groups of the PGMA block were hydrolyzed to obtain novel amphiphilic copolymer, poly(glyceryl methacrylate)‐block‐poly(pentafluorostyrene) [PGMA(OH)‐b‐PPFS]. The PGMA epoxy group hydrolysis was confirmed by ¹H NMR and FTIR spectroscopy. DSC investigation revealed that the PGMA‐b‐PPFS polymer was amorphous while the PGMA(OH)‐b‐PPFS displayed a high degree of crystallinity.

     

Precision Polyolefin Nanoalloy Polypropylene/Poly(ε‐caprolactone)

This communication reports the first example of precision polyolefin nanoalloys where an exotic immiscible polymer is nanometrically dispersed with stability in a polyolefin matrix in a highly controlled mode. Following the preparation of polypropylene/multiwalled carbon nanotubes nanocomposites (PP/MWCNTs) by in situ Ziegler‐Natta polymerization, the hydroxyl groups on the surfaces of individual MWCNTs are used to initiate ring‐opening polymerization of ε‐caprolactone, resulting in PP/poly(ε‐caprolactone) (PCL) alloy with PCL grafted on MWCNTs. Upon phase formation, the PP/MWCNTs‐g‐PCL alloys exhibit a unique PCL dispersion morphology, which is stable and solely governed by PCL molecular weight.