Kinetics of ultraviolet and plasma surface modification of poly(dimethylsiloxane) probed by sum frequency vibrational spectroscopy

In numerous applications in microfluidics, cell growth, soft lithography, and molecular imprinting, the surface of poly(dimethylsiloxane) (PDMS) is modified from a hydrophobic methyl-terminated surface to a hydrophilic hydroxyl-terminated surface. In this study, we investigated molecular structural and orientational changes at the PDMS-air interface in response to three commonly used surface modification processes: exposure to long-wavelength ultraviolet light (UV), exposure to short-wavelength UV that generates ozone (UVO), and exposure to oxygen plasma (OP). The surfaces of two PDMS compositions (10:1 and 4:1 of base polymer/curing agent) were probed during modification, using monolayer-sensitive IR + visible sum frequency generation (SFG) vibrational spectroscopy, with two different polarization combinations. During PDMS surface modification, the peak intensities of CH3 side groups and CH2 cross-link groups decreased, while peak intensities of Si-OH groups increased. There was no significant change in the average orientation of the CH3 groups on the PDMS surface during modification. The concentration of CH3 groups on the surface decreased exponentially with time, for all three UV, UVO, and OP modification processes, with first order kinetics and time constants of approximately 160, 66, and 0.3 min, respectively. At steady state, residual CH3 groups were detected at the PDMS surface for UV and UVO treatments; however, there were negligible CH3 groups detected after OP modification.     

Li+3 ion beam irradiation induced changes in the thermodynamic and electrical parameters of 4-n-(nonyloxy) benzoic acid

Li⁺³ ion beam irradiation studies on 4-n-(nonyloxy) benzoic acid (NOBA) have been carried out. Thermodynamic measurements demonstrate that all the phase transition temperatures are depressed for low value of irradiation fluence as compared to those for the pure NOBA and thereafter increase linearly with increase in irradiation fluence. It has also been observed that the temperature range of N and SmC phases in the heating and cooling cycles is improved due to irradiation. Dielectric investigations show that both the transverse as well as the longitudinal components of the dielectric permittivity are increased as compared with those of the pure sample due to irradiation. The observed change in the thermodynamic and dielectric parameters is attributed to the increased concentration of NOBA monomers over the NOBA dimers due to fragmentation of the hydrogen bonding in some of the NOBA dimers.     

Chemical modification of poly(substituted-acetylene). I. Synthesis and gas permeability of poly(1-trimethylsilyl-1-propyne)/poly (dimethylsiloxane) graft copolymer

In order to improve the selectivity and the stability and the stability for gas permeation of poly (1-trimethylsilyl-1-propyne) (PTMSP) membrane, it was chemically modified by grafting polydimethylsiloxane (PDMS) chains. The graft copolymers were synthesized by four different methods via metallation of PTMSP with n-butyllithium. PDMS content of the graft co-polymers was controlled in the range of 4–92 mol %. Very tough, thin membranes could be prepared from these graft copolymers using a solvent casting method. Thermal property and gas permeability of the copolymer membranes thus obtained were evaluated. These membranes were relatively thermally stable, and the softening points were over about 150°C. Oxygen permeability coefficients Po₂ and selectivity Po₂/PN₂ of PTMSP/PDMS graft copolymers depended on the PDMS content, the former was in the range of 1 X 10^?8 to 2 × 10^?7 cm³ (STP)· cm/(cm²· s · cm. Hg) and the latter was 2.0–3.1. Minimum values of PO₂ and PN₂ occured at PDMS content of about 55 mol %. The introduction of more than 60 mol % of PDMS resulted in oxygen permeability coefficient which was maintained for more than one moth (PO₂ = 2 ? 6 × 10 ^?8 cm ³ (STP)· cm/(cm²·s·cm Hg), PO₂/PN₂ = 2.3–2.7).     

A simple approach to micropatterning and surface modification of poly(dimethylsiloxane)

Ozone treatment is an efficient economical, alternative method for surface activation of poly(dimethylsiloxane) (PDMS). This is illustrated by the derivatization of a PDMS surface with (3-aminopropyl)triethoxysilane (APTES). The apparent surface concentration of amino groups was found to be ca. 10(-8) mol/cm2 using UV/visible spectroscopy of the product from the reaction of the amino groups and fluorescamine. Potential application for micropatterning of biologically active interfaces was demonstrated by the covalent immobilization of oligonucleotides. A simple process for photolithographic patterning on PDMS surfaces has been developed.     

Conformational behavior of poly(L-lactide) studied by infrared spectroscopy

This paper reports the analysis of the C=O stretching region of poly(L-lactide). This spectral band splits into up to four components, a phenomenon that a priori can be explained in terms of carbonyl-carbonyl coupling or specific interactions (such as C-H...O hydrogen bonding or dipole-dipole). Hydrogen bonding can be discarded from the analysis of the C-H stretching spectral region. In addition, low molecular weight dicarbonyl compounds of chemical structure similar to that of PLLA, such as diacyl peroxides, show a remarkable splitting of the carbonyl band attributed to intramolecular carbonyl-carbonyl coupling. Several mechanisms can be responsible for this behavior, such as mechanical coupling, electronic effects, or through-space intramolecular TDC (transition dipole coupling) interactions. Intermolecular dipole-dipole interactions (possible in the form of interchain TDC interactions) are proven to be of minor relevance taking into account the spatial structure of the PLLA conformers. The Simply Coupled Oscilator (SCO) model, which only accounts for mechanical coupling, has been found to predict adequately the relative intensity of the symmetric and asymmetric bands of dicarbonyl compounds. The dispersion curves predicted for PLLA by the SCO model also match those given by more general treatments, such as Miyazawa's first-order perturbation theory. Hence, the SCO model is adopted here as an adequate yet simple tool for the interpretation of band splitting caused by intramolecular coupling of polylactide. The four components observed in the C=O stretching band of semicrystalline PLLA are attributed to the four possible conformers: gt, gg, tt, and tg. The narrow bands observed for the interlamellar material are attributed to highly ordered chains, indicating the absence of a truly amorphous phase in the crystalline polymer. The interphase seems to extend over the whole interlamellar region, showing the features of a semiordered metastable phase. In amorphous PLLA, bands corresponding to gt, gg, and tt conformers also can be resolved by second derivative techniques, and curve-fitting results provide information about the conformational population at different temperatures.     

Cross-linking of poly(N-vinyl pyrrolidone) films by electron beam irradiation

Biocompatible hydrogels based on poly(N-vinyl pyrrolidone) (PVP) were synthesized by electron beam irradiation of the dry polymer under various conditions. Sol–gel analysis of the bulk gel (in mm range) gave a dose of gelation of 94 kGy. As seen for various other polymers, the network density rises with the increase in dose. At around 350 kGy, PVP began to decompose. Based on these observations, films in μm range on a silicon wafer were synthesized by electron beam irradiation. Due to irradiation, the films adhered irreversibly on the wafer. Their swelling behavior was analyzed by ellipsometry.     

Differential scanning calorimetry (DSC) and Raman spectroscopy study of poly(dimethylsiloxane)

Poly(dimethylsiloxane) was studied by laser Raman spectroscopy and differential scanning calorimetry. The Si O Si skeletal mode at 489 cm⁻¹ and the C Si C deformation bands at 188 cm⁻¹ and 158 cm⁻¹ were studied as functions of temperature from ambient to −130°C, and effects of temperature interpreted in accordance with results from thermal analysis. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2805–2810, 1998     

Structural and conformational changes during thermally‐induced crystallization of poly(trimethylene terephthalate) by infrared spectroscopy

Conformational changes occurring during thermally‐induced crystallization of poly(trimethylene terephthalate) (PTT) by annealing have been studied using density measurement, differential scanning calorimetry (DSC), and mid‐infrared spectroscopy (MIR). Infrared spectra of amorphous and semicrystalline PTT were obtained, and digital subtraction of the amorphous contribution from the semicrystalline PTT spectra provided characteristic MIR spectra of amorphous and crystalline PTT. The normalized absorbance of 1577, 1173, and 976 cm^?1 were plotted against the crystallinity showing that these bands can be used unambiguously to represent the trans conformation while the band at 1358 cm^?1 can be used to represent gauche conformation of methylene segment. The presence of a weak band at 1358 cm^?1 in the amorphous spectrum suggested that a small amount of gauche conformation is present in the amorphous phase. Infrared spectroscopy has been used for the first time as a means to estimate the trans and gauche conformations of methylene segments in PTT as a function of T_a. The amount of gauche conformation was plotted against the crystalline fraction and the extrapolation of this plot to zero crystalline fraction provided a value of 0.07, suggested that the pure amorphous phase consist of ～ 7% gauche conformation. It was found that the amorphous and crystalline gauche conformation increases at the expense of amorphous trans conformation during thermally induced crystallization of PTT. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1497–1504, 2008     

Determination of tacticity in poly(vinyl chloride) by infrared spectroscopy

From the temperature dependence of infrared spectra of poly(vinyl chloride) samples prepared by different methods, the intensity of the band at 690 cm.¹ (proportional to the number of isotactic diads in the sample), as well as that of the tacticity-independent C? H stretching band, was found to be independent of the crystallinity of the sample. These lines were therefore applied for the tacticity determination in poly(vinyl chloride), measured in the form of KBr pellets. The numerical tacticity value was obtained from the known values of absorbance coefficients of SCH and SHH type C? Cl stretching bands in solution, and from the shape of the spectrum.     

Rheo-optical fourier-transform infrared spectroscopy of polymers 16 orientation and strain-induced conformational regularity of poly(dimethylsiloxane) networks during cyclic elongation and recovery

Two SiO₂-filled poly(dimethylsiloxane) networks with different molar masses M_c (22000 g/mol and 33000 g/mol) between the junctions have been investigated by simultaneous mechanical and Fourier-transform infrared (FTIR) spectroscopic (rheo-optical) measurements to monitor the structural changes in cyclic elongation-recovery procedures. Higher polymer chain orientation was observed at corresponding elongations for the low-M_c network, but due to the higher extensibility appreciable strain-induced conformational regularity occurred only in the high-M_c material. Differences with reference to unfilled model networks are pointed out.     

Bioactive surface modification of mica and poly(dimethylsiloxane) with hydrophobins for protein immobilization

Bioactive surfaces with appropriate hydrophilicity for protein immobilization can be achieved by hydrophobin II (HFBI) self-assembly on mica and polydimethylsiloxane (PDMS) surfaces. X-ray photoelectron spectroscopy and water contact angle measurements illustrated that the surface wettability can be changed from superhydrophobic (PDMS) or superhydrophilic (mica) to moderately hydrophilic, which is suitable for protein (chicken IgG) immobilization on both substrate surfaces. The results suggest that HFBI assembly, one kind of hydrophobin from Trichoderma reesei, may be a versatile and convenient method for the immobilization of biomolecules on diverse substrates, which may have potential applications in biosensors, immunoassays, and microfluidic networks.     

Excitation of He—41 D-substates by He+- and Ne+-projectiles investigated by level-crossing techniques

Collisions of He⁺- and Ne⁺-projectiles with He at impact energies between 90 keV and 800 keV were investigated. Relative excitation cross sections for magnetic sublevels of He—4¹ D were determined using level-crossing techniques. Absolute excitation cross sections σ _m of the Zeeman-sublevels are given using He—4¹ D cross sections from earlier measurements. The results show strong variations of the cross sections σ₀ and σ_±1 with a quasi-oscillatory behaviour. σ_±2 is much smaller than σ₀ and σ_±1.     

Surface modification of poly(tetrafluoroethylene) with benzophenone and sodium hydride by ultraviolet irradiation

Poly(tetrafluoroethylene) (PTFE) films were surface modified in a solution of benzophenone and sodium hydride in dry dimethylformamide by ultraviolet (UV) light irradiation. The extent of surface modification was characterized after durations of UV light irradiation from 5–20 min at temperatures from 19–60°C. The modified films were analyzed by electron spectroscopy for chemical analysis, diffuse reflectance ultraviolet-visible light spectroscopy, attenuated total reflection Fourier transform infrared spectroscopy, dynamic contact angle measurement, and low-voltage scanning electron microscopy. PTFE surfaces produced by this modification demonstrated extensive defluorination, oxygen incorporation, surface unsaturation, and reduction in both advancing and receding dynamic water contact angles in a manner that was more extensive at long durations of irradiation and at high temperatures. Morphological damage depended upon treatment conditions, but extensive surface modification could be obtained without substantial morphological damage to PTFE films. Control experiments indicated that the surface modification proceeded by photoexcitation of either diphenyl ketyl radical anion or benzhydrol anion, the products of reaction of benzophenone with sodium hydride. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 1499–1514, 1997     

Melt crystallization and crystal transition of poly(butylene adipate) revealed by infrared spectroscopy

The structure evolution of poly(butylene adipate) (PBA) during isothermal melt crystallization and phase transition processes is investigated by Fourier transform infrared spectroscopy (FTIR). Detailed IR spectra analysis and band assignment are performed to disclose the bands sensitive to the alpha-form crystalline order of PBA. It is revealed from the in situ IR study that the functionalities within PBA chains alter simultaneously during the melt crystallization process. From the analysis of the spectral changes, it is found that band shifts take place during the phase transition process of PBA from its metastable beta-form crystal to the stable alpha-form. Notable band shifts in the 1300-1100 cm(-1) region indicate that the twist of polymer chains in the alpha-form is located in the C-O-C and C-O linkages. Moreover, the results elucidated that the different segments of molecular chains tune up their conformations synchronously during the beta to alpha crystal transition process of PBA. It is suggested that the betaalpha phase transition process proceeds randomly throughout the solid at a constant rate.     

Spectroscopic characterization of the conversion of poly(p-phenylene-vinylene) precursor by ion irradiation

Different spectroscopic techniques show that poly(p-phenylene vinylene) films can be derived from a sulphonium precursor by irradiation with ion beams at energies of the order of 100 keV. The comparison with the pyrolysis conversion shows less chlorine and sulfur residues in the irradiated thickness, whereas some ketone structures are evidenced. The formation of nanometric scale carbon clusters induced by the irradiation degradation of PPV is however indicated by UV spectrophotometry, leading to bandgap narrowing and increase of the conductivity. The irradiation with doping species allows the conversion and doping of PPV films in a single stage. The induced conductivity is limited by the formation of complexes with chlorine residues through a gettering process.     

Melting behavior of poly(3-hydroxybutyrate) investigated by two-dimensional infrared correlation spectroscopy

The melting behavior of a bacterially synthesized biodegradable polymer, poly(3-hydroxybutyrate) (PHB), was investigated by using generalized two-dimensional infrared (2D IR) correlation spectroscopy. Temperature-dependent spectral variations in the regions of the C-H stretching (3100-2850 cm(-1)), C=O stretching (1800-1680 cm(-1)), and C-O-C stretching (1320-1120 cm(-1)) bands were monitored during the melting process. The asynchronous 2D correlation spectrum for the C=O stretching band region resolved two crystalline bands at 1731 and 1723 cm(-1). The intense band at 1723 cm(-1) may be due to the highly ordered crystalline part of PHB, and the weak band at 1731 cm(-1) possibly arises from the crystalline part with a less ordered structure. These crystalline bands at 1731 and 1723 cm(-1) share asynchronous cross peaks with a band at around 1740 cm(-1) assignable to the C=O band due to the amorphous component. This observation indicates that the decreases in the crystalline components do not proceed simultaneously with the increase in the amorphous component. In the 3020-2915 cm(-1) region where bands due to the asymmetric CH3 stretching and antisymmetric CH2 stretching modes are expected to appear, eight bands are identified at 3007, 2995, 2985, 2975, 2967, 2938, 2934, and 2929 cm(-1). The bands at 2985 and 2938 cm(-1) are ascribed to the amorphous part while the rest come from crystal field splitting, which is a characteristic of polymers with a helical structure.     

Characterization of thin-film electroluminescent structures by SIMS and other analytical techniques

Analytical and Bioanalytical Chemistry - The recently developed Atomic Layer Epitaxy (ALE) method produces good quality electroluminescent thin-film structures which can be used in various display...