细长薄壁弹体的屈曲和靶体等效分析

利用金属靶开展动能深侵彻弹的穿甲屈曲实验研究。实验观察到长/短型弹体动塑性屈曲破坏分别表现为轴向皱褶型和轴向外翻撕裂型2种基本模式。不同的屈曲破坏模式与弹体几何、撞击初条件以及靶材等密切相关。区别于刚性尖头弹穿甲金属靶的韧性隧道开孔,尖头弹因屈曲破坏易变形为钝头形,导致弹体穿透靶板表现为挤凿穿甲。利用薄壁中空柱壳的弹性欧拉屈曲分析和弹体塑性屈服的极限分析给出弹体动塑性屈曲的临界条件。同时给出屈曲实验中混凝土靶和金属靶的等效条件。     

大长细比结构弹体侵彻2024-O铝靶的弹塑性动力响应

为研究大长细比结构弹体在撞击典型硬目标早期的结构动力学响应,利用57轻气炮进行了直径1.4 cm、量纲一壁厚0.1和0.15、长细比8和12、头部系数3和4.5的卵形空心弹体对2024-O铝靶的侵彻实验研究,利用高速摄影系统记录了弹体撞靶过程,观察到大长细比弹体垂直撞击硬目标过程中的局部墩粗、塑性屈曲2种结构破坏模式,以及斜侵彻过程中的整体塑性弯曲、弯曲与墩粗耦合、弯曲与屈曲耦合3种结构破坏模式和实时动力学响应过程。基于对指数硬化材料的空腔膨胀理论建立了弹体垂直侵彻模型,给出了在轴向及横向载荷交互作用下计算刚塑性自由梁危险截面屈服函数的控制方程,计算值与实验结果吻合较好。     

陶瓷/液舱复合结构抗侵彻数值分析

为研究陶瓷/液舱复合结构抗侵彻机理,在前期弹道冲击实验结果基础上,运用LS-DYNA进行了数值模拟,再现了陶瓷/液舱复合结构在弹体冲击下的破坏过程和破坏模式,得到与实验一致的结果。结果表明:弹体撞击结构后,结构内产生的冲击波以撞击处为圆心、以球形向前传播,并在结构内来回反射振荡;弹体在水中运动时,水中形成空泡且不断扩展,弹体头部水域形成高压区域;弹体发生墩粗和侵蚀破坏,在低速冲击下,弹体破坏主要发生在穿透陶瓷和前面板过程中,在高速冲击下,弹体破坏主要发生在水中运动阶段,最终形成类似“饼状”的严重变形;前、后面板发生局部破坏和整体变形,在高速弹体撞击下,后面板将发生花瓣开裂。     

A3钢钝头弹撞击45钢板破坏模式的数值分析

不同速度范围内的A3钢钝头弹撞击45钢靶板分别表现为泰勒撞击、向日葵型花瓣帽形失效和靶板冲塞穿甲等3种不同的破坏模式,利用LS-DYNA对这种复杂的破坏机理和相应的影响因素进行了数值模拟研究。采用Johnson-Cook强度模型和累积损伤失效模型描述弹靶材料的力学性能,并考虑了塑性变形的绝热温升效应。数值模拟再现了不同破坏模式的失效过程,得到了与实验一致的结果。研究还指出,弹靶的冲塞穿甲实际是在高速撞击下,弹体发生花瓣帽形变形失效后继续穿甲靶板的后续结果。     

充满水的金属圆柱壳经受轴向撞击时屈曲过程的实验研究

本文报道了五种规格充满水的圆柱壳经受大质量低速度轴向撞击作用时屈曲过程的实验结果。研究表明由于液体的存在，圆柱壳的屈曲模态呈轴对称型的环带波纹，整个撞击过程可以明显地分为振荡的动力加载、平稳发展的后屈曲和迅速下降的弹性卸载三个阶段。并讨论了试件壁厚和高度等几何参数对其屈曲性能的影响。     

充液圆柱壳轴向冲击屈曲的实验研究与计算机数值模拟

借助落锤装置实现冲击加载,完成了一组充满水的金属薄壁圆柱壳试件轴向冲击屈曲过程的实验研究,同时利用LS－DYNA大型动力软件对冲击屈曲的全过程进行了计算机模拟,对于屈曲模态发展过程以及冲击力和液压的动态时程曲线,实验观察和数值结果均表现出较好的一致性,研究表明,在撞击过程中壳内形成很大的液体压力,在此内压和轴向压缩的联合作用下,壳壁发生轴对称塑性屈曲,屈曲模态为一系列依次发展的环带波纹。     

修正金属本构模型在超高速撞击模拟中的应用

为更加准确地计算93钨合金弹超高速撞击Q345钢板问题,构建了修正的金属本构模型。引入GRAY三相物态方程描述材料相态变化,采用Johnson-Cook强度模型描述撞击后期材料的力学行为。结合封加波损伤演化模型以及Johnson-Cook失效模型描述不同应力三轴度下材料的拉伸、剪切失效行为;引入曹祥提出的断裂演化模型,描述材料失效后应力归零的过程。通过对比超高速撞击数值模拟结果与实验结果,验证了本构模型的适用性,并进一步分析了典型弹靶撞击条件下破片群的空间分布特征。研究结果表明：基于修正金属本构模型获得的超高速撞击靶板穿孔直径、弹体侵蚀长度、破片群扩展速度结果与实验结果一致;GRAY三相物态方程能够相对准确地给出弹体撞击首层靶板以及剩余弹体、破片群撞击第2层靶板时弹靶材料的熔化情况;封加波损伤演化模型能够准确判断超高速撞击过程中靶板是否产生层裂破坏;综合封加波损伤演化模型、Johnson-Cook失效模型以及曹祥提出的断裂演化模型后,数值模拟获得的破片群撞击后效靶板的穿孔面积与累积数量的统计曲线结果与实验结果一致;获得了典型条件下的柱形93钨弹体超高速撞击Q345靶板破片群空间分布结果...     

钨合金弹体对混凝土靶的超高速侵彻机理

为研究钨合金弹体超高速侵彻混凝土靶的相关机理,构建了适用于超高速撞击的金属强度模型、失效模型和混凝土的本构模型,对93钨合金弹体超高速撞击混凝土靶问题进行了数值模拟。开展了钨合金弹体超高速撞击混凝土靶实验,分析了靶板成坑特性,研究了侵彻总深度和残余弹体长度随撞击速度的变化规律,理论分析了长杆钨弹超高速撞击混凝土的侵彻模型和混凝土靶内的应力波传播。得到以下主要结论:（1）利用金属及混凝土的新本构模型获得的超高速撞击混凝土靶的破坏形貌数值模拟结果与实验结果一致;（2）超高速撞击条件下混凝土靶成坑为“弹坑＋弹洞”形,成坑体积与弹体动能近似成正比;（3）超高速撞击条件下,侵彻深度随弹速提高呈现先增大后减小的现象,高速段侵深降低是弹体经历销蚀侵彻后“刚体侵彻阶段”减少造成的;（4）建立的钨合金超高速撞击混凝土侵彻分析模型,可用来预估侵彻深度、残余弹长、蘑菇头直径等参数;（5）采用建立的超高速撞击混凝土靶内应力波传播理论模型得到的计算结果与实验结果吻合较好。     

A3钢钝头弹撞击45钢板破坏模式的试验研究

为了研究破片模拟弹的终点弹道效应,进行了不同质量A3钢钝头弹(弹径25 mm)撞击45钢板的试验研究,其中A3钢强度弱于45钢。在约200～800 m/s的撞击速度范围内,随着撞击速度的增加,分别观察到弹体出现泰勒撞击、向日葵型花瓣帽形失效及靶板冲塞穿甲三种破坏模式。伴随弹体和靶体经历的不同结构破坏模式,弹材和靶材也经历着相当复杂的材料失效。     

PMMA反射拉伸动态破坏的数值模拟

利用PMMA等透明材料弹丸撞击靶板可以直观再现和观测金属弹体撞击靶板的某些响应和破坏特性,研究PMMA在冲击载荷作用下的动态性能可为更好的分析和认识PMMA结构的动态响应提供支撑.基于文献中的实验构型,本文运用LS-DYNA开展了柱锥形PMMA试件在压缩入射波加载下动态响应的数值模拟,研究由于应力波在试件锥段的汇聚效应,以及在自由端的反射拉伸效应.分析了柱锥形PMMA试件的动态响应过程以及拉伸破坏特性,数值模拟获得了与实验相一致的试件破坏现象.     

Dynamic response and energy dissipation characteristics of balsa wood: experiment and analysis

Dynamic response of a cellular sandwich core material, balsa wood, is investigated over its entire density spectrum ranging from 55 to 380 kg/m³. Specimens were compression loaded along the grain direction at a nominal strain rate of 3 × 10³ s⁻¹ using a modified Kolsky (split Hopkinson) bar. The dynamic data are discussed and compared to those of quasi-static experiments reported in a previous study (Mech. Mater. 35 (2003) 523). Results show that while the initial failure stress is very sensitive to the rate of loading, plateau (crushing) stress remains unaffected by the strain rate. As in quasi-static loading, buckling and kink band formation were identified to be two major failure modes in dynamic loading as well. However, the degree of dynamic strength enhancement was observed to be different for these two distinct modes. Kinematics of deformation of the observed failure modes and associated micro-inertial effects are modeled to explain this different behavior. Specific energy dissipation capacity of balsa wood was computed and is found to be comparable with those of fiber-reinforced polymer composites.     

Experiments and modeling of ballistic penetration using an energy failure criterion

One of the most intricate problems in terminal ballistics is the physics underlying penetration and perforation. Several penetration modes are well identified, such as petalling, plugging, spall failure and fragmentation (Sedgwick, 1968). In most cases, the final target failure will combine those modes. Some of the failure modes can be due to brittle material behavior, but penetration of ductile targets by blunt projectiles, involving plugging in particular, is caused by excessive localized plasticity, with emphasis on adiabatic shear banding (ASB).Among the theories regarding the onset of ASB, new evidence was recently brought by Rittel et al. (2006), according to whom shear bands initiate as a result of dynamic recrystallization (DRX), a local softening mechanism driven by the stored energy of cold work. As such, ASB formation results from microstructural transformations, rather than from thermal softening. In our previous work (Dolinski et al., 2010), a failure criterion based on plastic strain energy density was presented and applied to model four different classical examples of dynamic failure involving ASB formation. According to this criterion, a material point starts to fail when the total plastic strain energy density reaches a critical value. Thereafter, the strength of the element decreases gradually to zero to mimic the actual material mechanical behavior.The goal of this paper is to present a new combined experimental–numerical study of ballistic penetration and perforation, using the above-mentioned failure criterion. Careful experiments are carried out using a single combination of AISI 4340 FSP projectiles and 25[mm] thick RHA steel plates, while the impact velocity, and hence the imparted damage, are systematically varied. We show that our failure model, which includes only one adjustable parameter in this present work, can faithfully reproduce each of the experiments without any further adjustment.Moreover, it is shown that the most common failure criterion based on a critical strain is simply inadequate to reproduce the results, due to the linear nature of the damage evolution. The advantages of the energy-based failure criterion are discussed in detail.     

轴向冲击载荷作用下弹性圆柱壳横向弯曲动态屈曲

研究在轴向冲击载荷下弹性圆柱壳动态屈曲问题.通过构造哈密顿体系,在辛空间中将临界载荷和动态屈曲模态归结为辛本征值和本征解问题.辛本征解反映了局部的压缩屈曲模态和整体的弯曲屈曲模态,特别是在冲击端为自由支承边界时的特殊屈曲方式.数值结果给出了具体的临界载荷和屈曲模态规律.     

ELASTO-PLASTIC DYNAMIC BUCKLING AND POSTBUCKLING OF SQUARE PLATES UNDER SOLID-FLUID SLAMMING

The elasto-plastic dynamic buckling and postbuckling phenomena ofsquare plates subjected to in-plane solid-fluid slamming are investigated.According tothe plate's response,the critical criteria for dynamic buckling,dynamic plasticity andplasti(?)collapse are defined,and the corresponding critical impulses are presented.Meanwhile,dynamic buckling modes and collapse models are observed.The effects ofdifferent boundary conditions and loading histories on the properties of buckling andpostbuckling are discussed.     

Deformation and Failure Modes of Soft Steel Projectiles Impacting Harder Steel Targets at Increasing Velocity

The present paper describes an experimental and numerical study concerning the impact of blunt steel projectiles against harder steel plates, at impact velocities between 200 and 800 m/s. In contrast with previously published observations, three modes of deformation and failure of the soft steel projectiles were observed in the present study. These included: Taylor cylinder mushrooming, sunflower-like petalling and plugging perforation. Individual velocity ranges and the transitions between the deformation/failure modes are identified by both experiments and numerical simulations. Complex material failure mechanisms of projectile and target play conflicting roles in the various penetration stages. Johnson–Cook models of strength and accumulative damage failure are employed in 3D numerical simulation to describe material behavior of both projectile and target. Computational evolutions of each scenario are offered in detail to understand the deformation and failure of projectile and target plate.     

圆柱薄壳的动相变屈曲行为

利用MTS809材料试验机对TiNi圆柱薄壳进行了轴向动渐进相变屈曲实验,对轴向冲击下处于伪弹性状态的TiNi合金柱壳的动相变屈曲行为进行了数值模拟研究。结果表明,不同的加载强度将会激发出柱壳不同的动屈曲响应模态。当冲击速度较高时,柱壳两端首先形成轴对称环形相变屈曲波纹,并产生应力平台;随着马氏体含量不断增加,环形相变屈曲波纹逐渐贯穿整个壳体,名义应力缓慢抬升;当名义应变超过一定阈值时,对称环形屈曲模态突变为非轴对称块状屈曲模态,名义应力大幅下降。撞击速度为40 m/s的算例（含10％随机缺陷）与S.Nemat-Nasser等的实验结果很好吻合,说明本文中计算模型、方法和结果的有效性经过了实验的考核。结果还表明,相变耗能是TiNi柱壳吸收冲击能量的主要机制,适合制作可重复使用的高效吸能元件,并给出了相应的理想厚径比。     

面内阶跃载荷下矩形薄板的塑性动力屈曲

对于面内阶跃载荷作用下矩形薄板的塑性动力屈曲问题,将临界应力和屈曲惯性项指数参数作为双特征参数求解。由相邻平衡准则导出失稳控制方程,由动力屈曲发生瞬间的能量转换和守恒准则,导出波阵面上的屈曲变形补充约束条件。失稳控制方程、边界条件、塑性波阵面上的连续条件和补充约束条件构成了定量求解两个特征参数和动力屈曲模态的完备条件。研究了矩形薄板塑性动力屈曲过程中板的厚宽比、冲击载荷大小、屈曲模态和临界屈曲长度之间的关系。