Evaluation of the Effect of Melt Memory on Shear‐Induced Crystallization of Low‐Density Polyethylene

Summary: The effect of melt memory on shear‐induced crystallization of a low‐density polyethylene melt is evaluated with a new shear DTA instrument. A critical strain is identified as the controlling factor for saturating the crystallization. Variation of this strain with the temperature of the sheared melt is established, and the melt state responsible for saturating the crystallization is identified by shear‐stress growth experiments at the steady‐state. Reptation times have been evaluated in both viscoelastic nonlinear and linear regimes, and it is shown that small‐angle oscillatory shear experiments cannot be used to probe effectively the effect of shear flow on the overall crystallization kinetics.

     

Redox‐Responsive Hydrogel System Using the Molecular Recognition of β‐Cyclodextrin

Summary: We have successfully constructed a redox‐responsible hydrogel system by combination of β‐cyclodextrin (β‐CD), dodecyl‐modified poly(acrylic acid) [p(AA/C₁₂)], and a redox‐responsive guest, ferrocenecarboxylic acid (FCA). In the reduced state of FCA, the ternary mixture exhibited a gel‐like behavior, whereas, in its oxidized state, the mixture exhibited a sol behavior.

Conceptual illustration for the redox‐responsive hydrogel system.     

Synthesis and Surface Morphology of Tetraaniline‐block‐Poly(L‐lactate) Diblock Oligomers

Summary: Tetraaniline‐block‐poly(L ‐lactide) diblock oligomers are synthesized via ring‐opening polymerization. The diblock oligomers cast from an L ‐lactide selective solvent (chloroform) show spherical aggregates for the leucoemeraldine state, and ring‐like structures that are composed of much smaller spherical aggregates for the emeraldine state. The formation mechanisms of the two different surface morphologies are discussed in detail.

Surface morphology changes induced by oxidation of the aniline segment of tetraaniline‐block‐poly(L ‐lactate) and drying effects.     

Synthesis of a Novel Fused Thiophene‐thieno[3,2‐b]thiophene‐thiophene Donor Monomer and Co‐polymer for Use in OPV and OFETs

The synthesis of a novel fused hexacyclic electron rich monomer incorporating thieno[3,2‐b]thiophene is reported and characterized by single crystal X‐ray diffraction. Suzuki co‐polymerization with benzothiadiazole (BT) afforded a novel low band‐gap polymer P4TBT with high molecular weights and good solution processability. Bulk heterojunction solar cell devices using the P4TBT and [70]PCBM gave power conversion efficiencies of 2.5%. Top‐gate, bottom‐contact field effect transistors (FETs) using P4TBT displayed high hole mobilities of 0.07 cm² · Vs⁻¹ demonstrating the suitability of the novel monomer and polymer for use in high performing organic electronic devices.

     

Reaction of Boranes with TMS Diazomethane and Dimethylsulfoxonium Methylide. Synthesis of Poly(methylidene‐co‐TMSmethylidene) Random Copolymers

Summary: Borane reacts with TDM by a sequence of insertion and disproportionation reactions to yield tris‐(trimethylsilylmethyl)borane. No further addition of TDM occurs. Triallylborane and tris‐(4‐methoxyphenylethyl)borane initiate the copolymerization of TDM and dimethylsulfoxonium methylide. The reactions afford TMS‐substituted polymethylene oligomers. The resultant poly(methylidene‐co‐TMSmethylidene) random copolymers arise from incorporation of TMSmethylidene (CHSiMe₃) and methylidene (CH₂) groups into the growing polymer chain one carbon at a time.

Trialkylborane‐catalyzed copolymerization of trimethylsilyl diazomethane and dimethylsulfoxonium methylide.     

Assembly of Anionic Conjugated Polymer with 6‐O‐Modified PNP‐β‐Galactoside for Fluorescence Logic‐signal‐based Multiplex Detections of Enzymes

Anionic conjugated polymer (PFP‐SO) was assembled with a novel enzymatic substrate 6‐O‐modified PNP‐β‐galactoside ( 1 ) for sensitive multiplex enzyme detections. The PFP‐SO/ 1 /lipase/β‐galactosidase system has two chemical input signals which are Input 1 (lipase) and Input 2 (β‐galactosidase), and output optical signals such as fluorescence emission at 416 nm or 450 nm. Four types of logic gates, including YES, INH, NAND and AND, were successfully constructed and utilized for multiplex detections of lipase and β‐galactosidase in one tube.

     

Color Indicator for Supramolecular Polymer Chemistry: Phenolphthalein‐Containing Thermo‐ and pH‐Sensitive N‐(Isopropyl)acrylamide Copolymers and β‐Cyclodextrin Complexation

The copolymerization parameters of N‐(isopropyl)acrylamide ( 1 ) and N‐(2‐hydroxy‐5‐(1‐(4‐hydroxyphenyl)‐3‐oxo‐1,3‐dihydroisobenzofuran‐1‐yl)benzyl)acrylamide ( 2 ) are determined. For both monomers, the homoaddition proceeds slightly faster than the heteroaddition step; however, the polymer formation occurs in a statistic fashion. Copolymers of different compositions are prepared and the cloud points are determined. Thereby, a significant influence of the concentration of monomer 2 and the pH value is found. For the first time, the complexation of polymer attached phenolphthalein by β‐cyclodextrins is shown. Furthermore, it is possible to achieve a decomplexation by the addition of suitable guest molecules. Both procedures can be followed with the naked eye.

     

Single‐Chain‐Particles of Poly(N‐isopropylacrylamide)

Spherical single‐chain‐particles of poly(N‐isopropylacrylamide) were prepared in aqueous solution above the lower critical solution temperature upon the addition of sodium dodecyl sulfate. The size of the single‐chain‐particles was investigated by means of transmission electron microscopy and viscosity measurements of the corresponding solutions, indicating the absence of inter‐chain entanglements among the single‐chain‐particles.

Schematic of the preparation of PNIPAM single‐chain‐globules in solution.     

Surfactant‐Free Spinning of Composite Carbon Nanotube Fibers

Summary: Fibers and yarns are promising forms to use and control the spatial orientation of carbon nanotubes in macroscopic materials. Various approaches have been proposed in the last few years to achieve fibers with a fraction of carbon nanotubes. Among them, coagulation spinning in aqueous media has proven to be a simple and capable method of leading to super‐tough materials. However, all water‐based processes described so far have made use of surfactant‐stabilized carbon nanotubes. In the present work, a method is shown to spin fibers from surfactant‐free nanotube solutions while preserving an all water‐based process. The resultant fibers exhibit mechanical and electrical properties that compare well with those of previously reported fibers spun with surfactants. The fibers exhibit a significant toughness and a high electrical conductivity.

Scanning electron micrograph of the fiber, showing the surface texture.     

Plasma‐Initiated Controlled/Living Radical Polymerization of Methyl Methacrylate in the Presence of 2‐Cyanoprop‐2‐yl 1‐dithionaphthalate (CPDN)

Summary: Plasma‐initiated controlled/living radical polymerization of methyl methacrylate (MMA) was carried out in the presence of 2‐cyanoprop‐2‐yl 1‐dithionaphthalate. Well‐defined poly(methyl methacrylate) (PMMA), with a narrow polydispersity, could be synthesized. The polymerization is proposed to occur via a RAFT mechanism. Chain‐extension reactions were also successfully carried out to obtain higher molecular weight PMMA and PMMA‐block‐PSt copolymer.

Dependence of ln([M]₀/[M]) on post‐polymerization time (above), and \overline M _{\rm n} and PDI against conversion (below) for plasma initiated RAFT polymerization of MMA at 25 °C.     

Block Copolymer PEO‐b‐PHPMA Synthesis Using Controlled Radical Polymerization on a Chip

Summary: Block copolymers of poly(ethylene oxide‐block‐2‐hydroxypropyl methacrylate) (PEO‐b‐PHPMA) with a range of molecular masses of the PHPMA block were obtained by controlled radical polymerization on a chip (CRP chip) using a PEO macroinitiator. A series of well‐controlled polymerizations were carried out at different pumping rates or reaction times with a constant ratio of monomer to initiator. The stoichiometry of the reactants was also adjusted by varying relative flow rates to change the reactant concentrations.

A schematic of a CRP chip and SEC traces of the PEO‐b‐PHPMA produced from different pump rates with a 1:100 ratio of initiator to monomer. The dashed peaks are the macroinitiator, PEO‐Br (left), and monomer, HPMA (right).     

The Ludwig‐Soret Effect on the Thermally Induced Phase Separation Process in Polymer Solutions: A Computational Study

The Ludwig‐Soret effect was investigated in the thermally induced phase separation process via SD in polymer solutions under an externally imposed spatial linear temperature gradient using mathematical modeling and computer simulation. The mathematical model incorporated non‐linear Cahn‐Hilliard theory for SD, Flory‐Huggins theory for thermodynamics, and the Ludwig‐Soret effect for thermal diffusion. 2D simulation results revealed that the Ludwig‐Soret effect had negligible impact on the phase separation mechanism in binary polymer solutions under a non‐uniform temperature field, as reflected by the time evolution of the dimensionless structure factor and the transition time from the early to the intermediate stages of SD.

     

Organosilicon‐Assisted Transformation of Living Anionic into Living Cationic Polymerization

A novel method is described for transforming an anionic polymerization process into a cationic polymerization process assisted by organosilyl groups. The reaction of the p‐tolyldimethylsilyl end group of polystyrene and trifluoromethanesulfonic acid produced a silyl triflate end group that served as a macroinitiator for the living cationic polymerization of isobutyl vinyl ether. The Si O linkage in the block copolymers underwent specific cleavage by reaction with tetrabutylammonium fluoride.

     

Functionalization of Crosslinked Vesicles by Co‐Self‐Assembly of a Gelable Diblock Copolymer and Mercaptosilane

Herein, a convenient and general method to simultaneously fix and functionalize polymeric vesicles with sulphydryl groups by the co‐self‐assembly of poly(ethylene oxide)‐block‐poly[3‐(triethoxysilyl)propyl methacrylate] (PEO‐b‐PTESPMA) and 3‐mercaptopropyltrialkoxysilane in an aqueous solution is reported. The presence of sulphydryl groups across the vesicle membrane has been confirmed by using an energy‐filtered technique during TEM analysis and by capturing Au nanoparticles.

     

Opto‐Mechanical Effect in Photoactive Nematic Side‐Chain Liquid‐Crystalline Elastomers

The mechanical behaviour of monodomain nematic side‐chain liquid‐crystalline elastomers containing azoderivatives as pendant groups or crosslinkers has been studied under UV irradiation and in the darkness at different temperatures. From the evaluation of the opto‐mechanical experiments, the mechanical efficiency, kinetic rates, activation energies and the isomerization mechanism of the azocompounds in the liquid‐crystalline matrix could be determined, as well as the effect of the chemical constitution of the azobenzene derivatives and their role in the elastomeric network.

     

Synthesis and Characterization of Amphiphilic Biodegradable Copolymer,Poly(aspartic acid‐co‐lactic acid)

An amphiphilic biodegradable polymer, poly(aspartic acid‐co‐lactic acid) (PAL), was synthesized by simply heating a mixture of aspartic acid (Asp) and L ‐lactide without additional catalysts or solvents. The unique branched architecture comprising succinimide units and lactic acid units was confirmed by IR and NMR spectroscopy. A copolymer of sodium aspartate and lactic acid (PALNa) was prepared by reacting PAL with an aqueous sodium hydroxide solution. The PAL was soluble in many organic solvents, while the PALNa was soluble in methanol and water. The hydrolytic degradation behavior of PAL varied with the copolymer composition. A higher Asp content resulted in a faster molecular weight decrease, and introducing glycolic acid units accelerated the degradation rate.

Microphotograph of microsphere of PAL‐1/5.     

A Green Approach for the Synthesis and Thiol‐ene Modification of Alkene Functio1489lized Poly(2‐oxazoline)s

The bulk polymerization of 2‐(dec‐9‐enyl)‐2‐oxazoline ( DecEnOx ), a fatty acid‐based monomer for the cationic ring‐opening polymerization, is reported. Furthermore, under optimal conditions, namely microwave heating at 100 °C, the bulk copolymerization with 2‐ethyl‐2‐oxazoline yielded well‐defined copolymers. Due to its pendant alkene groups DecEnOx ‐based polymers possess the potential to be modified in efficient thiol‐ene reactions. The functionalization with thiols, e.g., dodecanethiol and 2,3,4,6‐tetra‐O‐acetyl‐1‐thio‐β‐D ‐glycopyranose in “green” solvents is demonstrated.

     

Poly(2‐vinylpyridine)‐block ‐Poly(ϵ‐caprolactone) Single Crystals in Micellar Solution

Self‐assembly of poly(2‐vinylpyridine)‐block‐poly(ϵ‐caprolactone) (P2VP‐b‐PCL) diblock copolymer in the presence of a selective solvent is investigated by transmission electron microscopy and atomic force microscopy. Addition of water into a P2VP‐b‐PCL solution in N,N‐dimethylformamide at 20 °C produces elongated truncated lozenge shaped single crystals of uniform size and shape in large quantities. The single crystals are composed of PCL single‐crystal layer sandwiched between two P2VP layers tethered on the top and bottom basal surfaces. The formation of the single crystals is found to depend on the temperature. These findings provide a facile approach to the preparation of uniform single crystals in large quantities.

     

Polymer‐Based Rectifying Diodes on a Glass Substrate Fabricated by Ink‐Jet Printing

Summary: The fabrication of polymer diodes on a glass substrate by an ink‐jet printing technique is reported. Both an n‐type semiconductive polymer, poly[2‐methoxy‐5‐(2‐ethylhexyloxy)‐1,4‐(1‐cyanovinylene)phenylene] (CN‐PPV), and a p‐type semiconductive polymer, polypyrrole (PPy) or poly(3,4‐ethylenedioxythiophene) (PEDOT), were printed through a piezoelectric ink‐jet printer. The printed CN‐PPV/PPy and CN‐PPV/PEDOT diodes showed good rectifying characteristics. These results indicate the potential of the low‐cost ink‐jet printing technique to produce polymer microelectronic devices and circuits.

Schematic diagram of the printed polymer diode     

Diversified Applications of Chemically Modified 1,2‐Polybutadiene

Commercially available 1,2‐PB was transformed into a well‐defined reactive intermediate by quantitative bromination. The brominated polymer was used as a polyfunctional macroinitiator for the cationic ring‐opening polymerization of 2‐ethyl‐2‐oxazoline to yield a water‐soluble brush polymer. Nucleophilic substitution of bromide by 1‐methyl imidazole resulted in the formation of polyelectrolyte copolymers consisting of mixed units of imidazolium, bromo, and double bond. These copolymers, which were soluble in water without forming aggregates, were used as stabilizers in the heterophase polymerization of styrene and were also studied for their ionic conducting properties.