首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
Different succinic anhydrides were used for modification of hydrophobicities of linear and star-shaped poly (ε-caprolactone) oligomers with different molecular weights. Hydroxyl-terminated poly(ε-caprolactone) oligomers were acid-functionalized either with succinic anhydride (SAH) or with alkenylsuccinic anhydrides (ASAs) containing 8 or 18 carbons in their alkenyl chains. Hydrophobicities of the linear and corresponding star-shaped oligomers were investigated by immersion studies and by water contact angle measurements. In comparison with SAH functionalized oligomers, alkenyl chain containing oligomers showed lower thermal transitions and higher hydrophobicities. In addition, oligomers with 18 carbons alkenyl chain showed considerably higher hydrophobicities than corresponding oligomers with 8 carbon alkenyl chain.  相似文献   

2.
Summary: New functional poly(ester-anhydride)s with allyl pendant groups in the side chains were obtained by polycondensation of sebacic acid (SBA) and poly(3-allyloxy-1,2-propylene succinate) (OSAGE) terminated with carboxyl groups. The carboxyl groups in OSAGE and in SBA were converted to mixed anhydride groups by acetylation with acetic anhydride. After that, prepolymers obtained were condensed in vacuum to yield higher molecular weight poly(ester-anhydride)s. The influence of SBA and OSAGE content in poly(ester-anhydride)s on their selected properties e.g. molecular weight, thermal and solubility characteristics as well as degradation rate and mode, were examined. Poly(ester-anhydride)s were degraded in aqueous buffer of pH 7.4 at 37 °C. The hydrolytic degradation was monitored by determination of weight loss of samples and by determination of ester to anhydride groups ratio.  相似文献   

3.
The melt polycondensation reaction of the prepolymer prepared from N-(benzyloxycarbonyl)-L -aspartic acid anhydride (N-CBz-L -aspartic acid anhydride) and low molecular weight poly(ethylene glycol) (PEG) using titanium isopropoxide (TIP) as a catalyst produced the new biodegradable poly(L -aspartic acid-co-PEG). This new copolymer had pendant amine functional groups along the polymer backbone chain. The optimal reaction conditions for the preparation of the prepolymer were obtained by using a 0.12 mol % of p-toluenesulfonic acid with PEG 200 for 48 h. The weight-average molecular weight of the prepolymer increased from 1,290 to 31,700 upon melt polycondensation for 6 h at 130°C under vacuum using 0.5 wt % TIP as a catalyst. The synthesized monomer, prepolymer, and copolymer were characterized by FTIR, 1H- and 13C-NMR, and UV spectrophotometers. Thermal properties of the prepolymer and the protected copolymer were measured by DSC. The glass transition temperature (Tg) of the prepolymer shifted to a significantly higher temperature with increasing molecular weight via melt polycondensation reaction, and no melting temperature was observed. The in vitro hydrolytic degradation of these poly(L -aspartic acid-co-PEG) was measured in terms of molecular weight loss at different times and pHs at 37°C. This pH-dependent molecular weight loss was due to a simple hydrolysis of the backbone ester linkages and was characterized by more rapid rates of hydrolysis at an alkaline pH. These new biodegradable poly(L -aspartic acid-co-PEG)s may have potential applications in the biomedical field. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 2949–2959, 1998  相似文献   

4.
Poly(lactic acid) (PLA) was submitted to solid state polymerization (SSP) in a fixed bed reactor under nitrogen flow, so as to examine technique efficiency for increasing the molecular weight and hence permitting the reduction of the melt polymerization residence times. In order to use a suitable starting material, SSP prepolymers of low and medium molecular weight were first prepared through solid state hydrolysis of commercial PLA grade under acidic and alkaline conditions. During these degradation runs, hydrolysis involved the random scission of ester groups in the polymer backbone, while the relevant kinetics and the resulting thermal properties were also examined. In a subsequent step, the prepolymers obtained were subjected to SSP at three temperatures, approximately 2.5–25.0 °C below their melting point. The process achieved an increase of up to 1.7 times the initial molecular weight, however, with different trends depending on the prepolymer characteristics, reaction temperature and time, as well as the pH of the hydrolysis medium. In addition to molecular weight build up, the effect of the SSP process on end product thermal properties was also investigated.  相似文献   

5.
Hydroxy terminated polybutadiene has been used for the first time in the synthesis of poly(ester-imide)s [P(E-I)s]. Anhydride terminated polyester prepolymers were prepared by the reaction of two different polyols--polytetramethyleneoxide glycol (PTMG) of molecular weight 1000 and hydroxy terminated polybutadiene (HTPB) of molecular weight 2500--and different dianhydrides--pyromellitic dianhydride (PMDA), benzophenonetetracarboxylic dianhydride (BTDA) and 4,4-(hexafluoroiso-propylidene)diphthalic anhydride (HFDA). The prepolymers were then reacted with different diisocyanates--80:20 mixture of 2,4- and 2,6-tolylene diisocyanate (TDI), 1,6-hexamethylene diisocyanate (HDI), isophorone diisocyanate (IPDI) and 4,4-methylene bis(phenylisocyanate) (MDI) resulting in P(E-I)s. The P(E-I)s were characterised by FT-IR, FT-NMR, GPC, TGA, DSC and for static and dynamic mechanical properties. The polymers based on PTMG showed two distinct melting points and behave as thermoplastic elastomers. The thermal stability and mechanical properties of P(E-I)s based on HTPB were substantially higher than those based on PTMG.  相似文献   

6.
A series of silicon containing poly(ester imide)s [PEIs] were synthesized using novel vinyl silane diester anhydride (VSEA) and various aromatic and aliphatic dimines by two-step process includes ring-opening polyaddition reaction to form poly(amic acid) and thermal cyclo-dehydration process to obtain poly(ester imide)s. VSEA was synthesized by using dichloro methylvinylsilane and trimellitic anhydride in the presence of K2CO3 by nucleophilic substitution reaction. The PEIs were characterized by FTIR spectroscopy. The thermal properties of PEIs were investigated by using differential scanning calorimetry (DSC) and thermogravimetric analysis (TG) methods. The prepared PEIs showed glass transition temperatures in the range of 320–350°C and their 5% mass loss was recorded in the temperature range of 500–520°C in nitrogen atmosphere. These had char yield in the range of 45–55% at 800°C.  相似文献   

7.
A series of aliphatic–aromatic multiblock copolyesters consisting of poly(ethylene‐co‐1,6‐hexene terephthalate) (PEHT) and poly(L ‐lactic acid) (PLLA) were synthesized successfully by chain‐extension reaction of dihydroxyl terminated PEHT‐OH prepolymer and dihydroxyl terminated PLLA‐OH prepolymer using toluene‐2,4‐diisoyanate as a chain extender. PEHT‐OH prepolymers were prepared by two step reactions using dimethyl terephthalate, ethylene glycol, and 1,6‐hexanediol as raw materials. PLLA‐OH prepolymers were prepared by direct polycondensation of L ‐lactic acid in the presence of 1,4‐butanediol. The chemical structures, the molecular weights and the thermal properties of PEHT‐OH, PLLA‐OH prepolymers, and PEHT‐PLLA copolymers were characterized by FTIR, 1H NMR, GPC, TG, and DSC. This synthetic method has been proved to be very efficient for the synthesis of high‐molecular‐weight copolyesters (say, higher than Mw = 3 × 105 g/mol). Only one glass transition temperature was found in the DSC curves of PEHT‐PLLA copolymers, indicating that the PLLA and PEHT segments had good miscibility. TG curves showed that all the copolyesters had good thermal stabilities. The resulting novel aromatic–aliphatic copolyesters are expected to find a potential application in the area of biodegradable polymer materials. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5898–5907, 2009  相似文献   

8.
Repair and regeneration of bone defects with particular shape may be enhanced by in situ forming biomaterials which can be used in minimal invasive surgery. This study is aimed to prepare novel in situ forming biodegradable nanocomposites based on poly(3‐allyloxy‐1,2‐propylene) succinate (PSAGE) and nanosized hydroxyapatite (HA). These nanocomposite materials contain poly(ester‐anhydride) (PEA) microspheres embedded in a polyester matrix prepared by crosslinking PSAGE with oligo(1,2‐propylene maleate) and methacrylic monomers. Methyl methacrylate and one of hydrophilic oligo(ethylene glycol) methacrylates with different functionality and various length of oligooxyethylene chains were used as polymerizable diluents. Incorporation of microspheres which degrade faster than crosslinked polyester matrices enables formation of porous structure in situ. The obtained materials are liquid before curing and harden in several minutes with moderate exothermic effect. The effect of the composition of nanocomposite materials on selected properties, such as water sorption, mechanical strength, porosity and hydrolytic degradation process, was investigated. Rheological behavior and injectability of liquid formulations were studied. Analysis by energy dispersive spectroscopy confirmed the presence of characteristic features of HA in the nanocomposite materials. The morphology of the cured nanocomposites subjected to hydrolytic degradation was evaluated by scanning electron microscopy. The MTS cytotoxicity assay was carried out for extracts from crosslinked materials using hFOB1.19 cells. It was found that the extracts exhibit a dose‐dependent cytotoxic response. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

9.
The phase‐separation behavior of thermoplastic poly(ester‐imide) [P(E‐I)] multiblock copolymers, (A‐B)n, was investigated by a stepwise variation of the imide content. All the multiblock copolymers were synthesized by solution polycondensation with dimethylformamide as a solvent. P(E‐I)s were prepared with anhydride‐terminated polyester prepolymer and diisocyanates. Polyester prepolymers were prepared by the reaction of pyromellitic dianhydride and two different polyols [poly(tetramethylene oxide glycol) (PTMG) and polycaprolactone diol (PCL)]. Structural determination was done with Fourier transform infrared spectroscopy and Fourier transform NMR, and the molecular weight was determined by gel permeation chromatography. The effect of the imide content on the thermal properties of the synthesized P(E‐I)s was investigated by thermogravimetric analysis and differential scanning calorimetry. The polymers were also characterized for static and dynamic mechanical properties. Thermal analysis data indicated that the polymers based on PTMG were stable up to 330 °C in nitrogen atmosphere and exhibited phase‐separated morphology. Polymers based on PCL showed multistage decomposition, and the films derived from them were too fragile to be characterized for static and dynamic mechanical properties. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 341–350, 2004  相似文献   

10.
Poly(propylene succinate)/poly(ε‐caprolactone) (PPSu/PCL) 25/75, 50/50, and 75/25 w/w copolymers were prepared using a combination of polycondensation and ring opening polymerization. The randomness of copolymers was characterized using 1H NMR and 13C NMR spectroscopy. From molecular weights and DSC measurements it was observed that the molecular weight decreased with increasing the wt % content of PPSu, while the copolymers containing 50 and 75 wt % PPSu were completely amorphous. Enzymatic hydrolysis revealed that biodegradation rate was much enhanced compared with that of neat PCL and increased by increasing the PPSu content. From TGA analysis it was also found that the PPSu/PCL copolymers had similar thermal decomposition behaviour with the pure polyesters and exhibited their maximum decomposition rates at temperatures 400–420 °C. Two different mechanisms, which follow each other, were used to adequately describe their decomposition kinetics. The first one corresponded to the first stage taking place at 280–365 °C, where small mass loss was recorded and activation energies ranged between 94 and 156 kJ/mol. The second one took place at 370–460 °C and corresponded to the stage where the main polyester mass was decomposed. The activation energies for this stage ranged between 200 and 240 kJ/mol. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5076–5090, 2007  相似文献   

11.

Multi‐block copolymers of PLLA and PCL were prepared by a coupling reaction between PLLA and PCL prepolymers with –NCO end groups. FTIR proved that the products were PLLA‐PCL copolymers. The weight‐average molecular weight of the copolymers was up to 180,000 at a composition of 60% PLLA and 40% PCL. The degradation properties of PLLA and PLLA‐PCL copolymers were studied by a soil burial test and a hydrolysis test in a phosphate‐buffer solution. The degradation rate was estimated by the mass loss, molecular weight reduction, pH value changes and swelling index; the degradation rates of the copolymers were a function of the composition of PLLA and PCL. Increasing PCL content in the copolymers resulted in lower degradation rate.  相似文献   

12.
Simultaneous solid‐state polycondensation (SSP) of the powdery prepolymers of poly(L ‐lactic acid) (PLLA) and poly(D ‐lactic acid) (PDLA) can produce entire stereocomplexed poly(lactic acid)s (sc‐PLA) with high molecular weight and can be an alternative synthetic route to sc‐PLA. Ordinary melt polycondensations of L ‐ and D ‐lactic acids gave the PLLA and PDLA prepolymers having medium molecular weight which were pulverized for blending in 1:1 ratio. The resultant powder blends were then subjected to SSP at 130–160 °C for 30 h under a reduced pressure of 0.5 Torr. Some of the products thus obtained attained a molecular weight (Mw) as high as 200 kDa, consisting of stereoblock copolymer of PLLA and PDLA. A small amount of the stereocomplex should be formed in the boundaries of the partially melted PLLA and PDLA where the hetero‐chain connection is induced to generate the blocky components. The resultant SSP products showed predominant stereocomplexation after their melt‐processing in the presence of the stereoblock components in spite of containing a small amount of racemic sequences in the homo‐chiral PLLA and PDLA chains. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3714–3722, 2008  相似文献   

13.
Novel sulfur‐containing biphenol monomers were prepared in high yields by the reaction of 4‐mercaptophenol with chloropyridazine or chlorophthalazine compounds. High‐molecular‐weight poly(arylene ether)s were synthesized by a nucleophilic substitution reaction between these sulfur‐containing monomers and activated difluoro aromatic compounds. The inherent viscosities of these polymers ranged from 0.34 to 0.93 dL/g. The poly(pyridazine)s exhibited glass‐transition temperatures greater than 165 °C. The poly(phthalazine)s showed higher glass‐transition temperatures than the poly(pyridazine)s. A polymer synthesized from a bisphthalazinebiphenol and bis(4‐fluorophenyl)sulfone had the highest glass‐transition temperature (240 °C). The thermal stabilities of the poly(pyridazine)s and poly(phthalazine)s showed similar patterns of decomposition, with no significant weight loss below 390 °C. The poly(phthalazine)s were soluble in chlorinated solvents such as chloroform, and the poly(pyridazine)s were soluble in dipolar aprotic solvents such as N,N′‐dimethylacetamide. The soluble poly(pyridazine)s and poly(phthalazine)s could be cast into flexible films from solution. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 262–268, 2007  相似文献   

14.
Hydrolysis of poly(L -lactide) (PLLA) films in 0.01N NaOH at 37°C was investigated by gel permeation chromatography, differential scanning calorimetry, scanning electron microscopy, and polarizing optical microscopy. The change in molecular weight distribution and surface morphology of PLLA films during hydrolysis revealed that PLLA film hydrolysis in dilute alkaline solution proceeded mainly via the surface erosion mechanism. An insignificant dependence of the rate of weight loss per unit surface area on the PLLA film thickness also supported this conclusion. Etching of the outside of PLLA spherulites resulted in preferred hydrolysis of PLLA chains in the amorphous region. The disorientation of lamella and inhomogeneous erosion in the spherulites implied that hydrolysis of PLLA chains occurred predominantly in the amorphous region between the crystalline regions in the spherulites. The rate of weight loss per unit surface area decreased linearly with the increase in the initial crystallinity of PLLA film, while the radius of spherulites had practically no significant effect on the hydrolysis of PLLA film. The specific low molecular weight of PLLA chains produced by hydrolysis increased with the rise in annealing temperature of the PLLA film, suggesting that the PLLA chains released were the component of one fold in the crystalline region. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 59–66, 1998  相似文献   

15.
A spirobichroman structure-containing diether anhydride (SBCDA), 6,6′-bis(3,4-dicarboxyphenoxy)-4,4,4′,4′,7,7′-hexamethyl-2,2′-spirobichroman dianhydride, was prepared by the nucleophilic nitrodisplacement of 4-nitrophthalonitrile with the phenolate ion of 6,6′-dihydroxy-4,4,4′,4′,7,7′-hexamethyl-2,2′-spirobichroman, followed by alkaline hydrolysis of the intermediate tetranitrile and dehydration of the resulting tetraacid. A series of high molecular weight poly(ether imide)s with inherent viscosities between 0.45 and 1.28 dL/g were synthesized from SBCDA and various aromatic diamines via a conventional two-stage procedure that included ring-opening polyaddition in N,N-dimethylacetamide (DMAc) to give poly(amic acid)s, followed by thermal cyclization to poly(ether imide)s. The intermediate poly(amic acid)s had inherent viscosities of 0.70–1.50 dL/g. Except for the poly(ether imide) obtained from p-phenylenediamine, the other poly(ether imide)s were soluble in various organic solvents and could be solution-cast into transparent, flexible, and tough films. These poly(ether imide)s had glass transition temperatures in the range 175–262°C and showed no significant decomposition below 420°C, with 10% weight loss being recorded above 446°C in nitrogen or air. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 2801–2809, 1997  相似文献   

16.
A group of new, water-soluble poly(ether-urethane)s, derived from poly(ethylene glycol) and the amino acid L -lysine, provide pendent carboxylic acid groups along the polymer backbone at regular intervals. The carboxylic acid groups were utilized for the attachment of acrylate and methacrylate pendent chains (hydroxyethyl acrylate, hydroxyethyl methacrylate, aminoethyl methacrylate, and aminoethyl methacrylamide), leading to functionalized polymers. The pendent chains were attached via ester and/or amide bonds having different degrees of hydrolytic stability. The attachment reactions proceeded with high yields (up to 95%). The functionalized polymers were subsequently photopolymerized (UV irradiation) to obtain crosslinked hydrogels. Crosslinked membranes with the highest degree of mechanical strength were obtained when the crosslinking reaction was performed in dioxane with benzoin methyl ether (0.1 wt %) as the initiator. the crystallinity, thermomechanical properties, and hydrolytic stability of the crosslinked membranes were studied. All membranes were transparent and highly swellable (equilibrium water content: 64–88%). The tensile strength in the swollen state ranged from 0.15 to 1.09 MPa. Under physiological conditions (phosphate buffered water, 0.1M, pH 7.4, 37°C) the hydrolytic stability of the hydrogels varied depending on the bonds used in the attachment of the acrylate pendent chains: Hydrogels with hydroxyethyl acrylate pendent chains dissolved within 30 days, while hydrogels containing aminoethyl methacrylamide pendent chains remained unchanged throughout a 30 day period. Using high molecular weight FITC-dextrans as model compounds, complete release from the swollen hydrogels required between 60 and 150 h. Overall, the evaluation of poly(ethylene glycol)-lysine derived, photocrosslinked hydrogels indicated that these materials provide a range of potentially useful properties. © 1994 John Wiley & Sons, Inc.  相似文献   

17.
New degradable poly(ester anhydride)s were prepared by the melt polycondensation of diacid oligomers of poly(sebacic acid) (PSA) transesterified with ricinoleic acid. The transesterification of PSA with ricinoleic acid to form oligomers was conducted via a melt bulk reaction between a high molecular weight PSA and ricinoleic acid. A systematic study on the synthesis, characterization, degradation in vitro, drug release, and stability of these polymers was performed. Polymers with weight‐average molecular weights of 2000–60,000 and melting temperatures of 24–77 °C were obtained for PSA containing 20–90% (w/w) ricinoleic acid. NMR and IR analyses indicated the formation of ester bonds along the polyanhydride backbone. These new degradable copolymers have potential use as drug carriers. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1059–1069, 2003  相似文献   

18.
通过己内酯和氨基己酸开环、缩合反应制备了酯段含量为81%的线性聚酯酰胺(PEA),并用熔融共混的方法制备了PEA/聚碳酸亚丙酯(PPC)共混物,考察了PEA的引入对共混体系相容性、热力学稳定性和机械性能的影响。 结果表明,PEA与PPC之间有较好的相容性,共混物的热力学稳定性比PPC有显著提高,当PEA质量分数为3%时,共混体系的起始分解温度(T-5%)和最大分解速率时的温度(Tmax)比PPC分别提高了52.7%和46.4%。 通过调节PEA的含量可以使共混体系同时达到增强和增韧的效果。  相似文献   

19.
Isocyanate-terminated prepolymers were synthesized using poly(tetramethylene oxide)glycol of molecular weight 1000 (PTMG1000) with tolylene-2,4-diisocyanate (TDI). The prepolymers were chain extended with N-methyldiethanolamine (N-MDEA) to form polyurethanes containing tertiary nitrogen. These polyurethanes were crosslinked with bromine terminated polyurethane, poly(urethane-imide), and poly(urethane-siloxane) through the formation of cationomers at tertiary nitrogen sites across the backbone polyurethanes.

The crosslinked cationomeric polyurethanes were characterized by Fourier Transform Infrared Spectroscopy (FTIR), Thermogravimetric Analysis (TGA), mechanical analyses, (static and dynamic), and static contact angles measurements. FTIR spectral studies confirms the formation of bromine terminated poly(urethane-imide) and poly(urethane-siloxane), as well as quaternization of the tertiary nitrogen which leads to crosslinking. A comparison of thermal stabilities of crosslinked polymers with respect to the chemical nature of bromine terminated prepolymers (BTP) indicates improved thermal stability for poly(urethane-imide) based ABCP. Stress-strain analysis shows high elongation values for poly(urethane-siloxane) and poly(urethane-imide) based ABCPs. Dynamic mechanical analysis reveals better damping for poly(urethane- siloxane) based AB crosslinked polymers.  相似文献   

20.
Thermal degradation of a serials of star-shaped poly(?-caprolactone) (PCL) with well-defined arm numbers and arm length was investigated. The weight loss of star-shaped PCL during heating process showed a two-stage character, and its dependence on molecular weight and multi-armed structure was well discussed. It was found that the thermal stability could be improved not only by increasing molecular weight but also by increasing arm numbers when the molecular weight is in a certain range. Based on the analyses of pyrolytic products by 1H NMR and TGA-FTIR, two mechanisms of thermal degradation for the random cleavage of ester bonds of PCL chains were proposed. Ester bonds were pyrolyzed into alkene and carboxyl functional groups in mechanism I while they were pyrolyzed into ketene and hydroxyl functional groups in mechanism II. The effects of multi-armed structure of star-shaped PCL on the cleavage of ester bonds of PCL chains were discussed in terms of the limitation of central “core” on mobility of each PCL arm. Combined the results of viscosity analysis with thermal analysis, it could be concluded that both thermal stability and processability of PCL materials can be improved by controlling the multi-armed structures.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号