首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到18条相似文献,搜索用时 156 毫秒
1.
多孔阳极氧化铝薄膜光学常数的确定   总被引:5,自引:0,他引:5       下载免费PDF全文
根据多孔阳极氧化铝(AAO)薄膜的实验透射谱(200—2500nm),采用极值包络线算法确定其光学常数,并由此较精确地计算出AAO薄膜样品在该波段的光学常数.结果表明,多孔氧化铝薄膜表现出直接带隙(能隙约4.5eV)半导体的光学特性,且其光学常数与制样中的重要工艺参数阳极氧化电压有显著的相关性,即随阳极氧化电压的增加,AAO薄膜的厚度、折射率和光学能隙变大,消光系数减小.同时,计算得到的薄膜厚度与实测值相吻合,则说明计算结果和实验值是自洽的. 关键词: 薄膜光学 光学常数 多孔阳极氧化铝 阳极氧化电压  相似文献   

2.
采用二步阳极氧化法在草酸溶液中制备了高度有序的多孔阳极氧化铝(Porous Anodic Alumina,PAA)薄膜。以多孔氧化铝薄膜为模板,采用真空电子束蒸发的方法在多孔氧化铝模板上制备出了高度有序的金属银纳米点阵列体系。扫描电镜(SEM)测试结果表明,所制备的金属银纳米点阵列与多孔阳极氧化铝膜的多孔阵列具有完全相同的有序结构,阵列中银纳米颗粒的形状接近球形,其直径大约为70nm,与氧化铝模板的孔径基本一致。研究了高度有序银纳米点阵列的形成过程。  相似文献   

3.
以多孔阳极氧化铝膜(porous anodic alumina, PAA)为基片,采用真空电子束蒸发的方法在多孔氧化铝膜上制备了高度有序度的Sn纳米点阵列.锡纳米点阵的XRD与块体锡的完全相同,扫描电镜(SEM)测试结果表明,所制备的金属Sn纳米点阵与阳极氧化铝膜的多孔阵列具有完全相同的有序结构,阵列中每个Sn纳米粒子的形状为球形的,其直径接近于PAA膜的孔直径.对Sn纳米点阵形成过程和形成机理进行了讨论.  相似文献   

4.
以多孔阳极氧化铝(porous anodic alumina,PAA)膜为模板,采用真空电子束蒸镀技术,分别在PAA多孔层以及阻挡层表面形成了银纳米孔和银纳米帽有序阵列表面增强拉曼散射(surface-enhancedRaman scattering,SERS)活性基底,并以膀胱肿瘤细胞作为分子探针,测试和分析了这两种SERS活性基底的表面增强拉曼光谱的特性。结果表明,两种SERS活性基底对膀胱肿瘤细胞的拉曼散射信号均有很好的增强作用。银纳米帽有序阵列SERS活性基底不仅具有较高的SERS增强和荧光猝灭效应,而且不存在与PAA膜中草酸根杂质相关的干扰峰,可获得膀胱肿瘤细胞拉曼散射光谱的更多细节信息。  相似文献   

5.
利用多孔阳极氧化铝(PAA)的纳米列阵结构,将金属铜电镀到氧化铝的孔中,得到含有金属铜纳米列阵阳极氧化铝(Cu/PAA)膜。实验中发现,Cu/PAA膜的偏振特性与电镀条件有关。在一定的范围内,随着电镀时间和电流密度的增加,消光比增大。电镀溶液的温度也是影响Cu/PAA膜消光比的一个很重要的因素,在电镀溶液温度相对较高的情况下,电流密度相对较小时也可以获得相对较高的消光比。通过优化电镀条件可获得高效率的Cu/PAA膜微偏振器。这种电化学方法制备的微偏振器,制备工艺简单,尺寸可控,便于实现产业化,有广泛的应用前景。  相似文献   

6.
立方氮化硼薄膜的光学带隙   总被引:1,自引:0,他引:1       下载免费PDF全文
邓金祥  汪旭洋  姚倩  周涛  张晓康 《物理学报》2008,57(10):6631-6635
用射频溅射法在p型Si(100)衬底上沉积立方氮化硼(c-BN)薄膜,薄膜的成分由傅里叶变换红外谱标识,用紫外-可见分光光度计测量了c-BN薄膜的反射光谱,利用K-K(Kramers-Kroning)关系从反射谱计算出c-BN薄膜的光吸收系数,进而确定c-BN薄膜的光学带隙.对于立方相含量为55.4%的c-BN薄膜,光学带隙为5.38eV. 关键词: 立方氮化硼薄膜 光学带隙 K-K关系  相似文献   

7.
热舟蒸发LaF3薄膜的紫外性能研究   总被引:3,自引:0,他引:3       下载免费PDF全文
研究了沉积温度对热舟蒸发氟化镧薄膜结构和光学性能的影响,沉积温度从200℃上升到350℃.间隔为50℃.采用分光光度计测量了样品的透射率和反射率光谱曲线,并在此基础上进行了光学损耗、光学常数以及带隙和截止波长的计算.采用表面轮廓仪进行了表面形貌和表面粗糙度的标定,采用X射线衍射(XRD)方法测量了不同沉积温度下样品的微结构.发现在短波长波段,随着沉积温度的升高,光学损耗增加,晶粒尺寸增大,表面粗糙度略有增加.不过散射损耗在光学损耗中所占比例均很小,光学损耗的增加主要由吸收损耗引起.随着沉积温度的升高,折射率与消光系数增大,带隙变小,相对应的截止波长向长波方向移动.  相似文献   

8.
利用阳极氧化的方法制备出几种表面结构和尺度不同的多孔氧化铝薄膜,用原子力显微镜扫描获得了这些薄膜表面的纳米结构图像,并采用光谱仪测定了它们的反射光谱。实验表明,平均孔径为26和39 nm的多孔氧化铝薄膜表面具有独特的反射光谱,在500至1 000 nm波长范围内呈周期性地密集峰—谷分布,峰—谷的密集度或数量取决于薄膜表面纳米结构的尺度。讨论了纳米结构尺度与反射光谱之间的相互关系,并给出了适当的解释。  相似文献   

9.
沉积压力对氢化非晶硅薄膜特性的影响   总被引:1,自引:0,他引:1  
采用等离子增强化学气相沉积(PECVD)系统,以乙硅烷和氢气为气源,普通钠钙玻璃为衬底制备了氢化非晶硅(a-Si∶H)薄膜,研究了沉积压力对非晶硅薄膜的沉积速率、光学带隙以及结构因子的影响。采用台阶仪、紫外可见分光光度计、傅里叶变换红外光谱仪和扫描电子显微镜等手段分别表征了a-Si∶H薄膜的沉积速率,光学带隙、结构因子和表面形貌。结果表明: 随着沉积压力的增加,沉积速率呈现先上升后下降的趋势,光学带隙不断下降。当沉积压力小于210 Pa时,以SiH键存在的H原子较多,而以SiH2或SiH3等形式存在的H较少; 当沉积压力大于210 Pa时,以SiH2,(SiH2)n或SiH3等形式存在的H较多。通过结构因子的计算,发现沉积压力在110~210 Pa的范围内沉积的薄膜质量较好。  相似文献   

10.
苑进社  陈光德  齐鸣  李爱珍  徐卓 《物理学报》2001,50(12):2429-2433
用XPS和AES电子能谱的方法对等离子体辅助分子束外延(MBE)生长的GaN薄膜进行了表面分析和深度剖析.发现红外分子束外延(RFMBE)生长的富镓GaN薄膜实际表面存在O和C吸附层,C主要为物理吸附,而O在GaN表面形成局域化学键产生氧络合物覆盖层,并形成一定的深度分布.杂质O在GaN带隙中导带底形成杂质带同时引入深受主能级,使得带隙变窄室温光吸收谱向低能方向移动,光致发光谱出现宽带发光峰.从而影响GaN薄膜的电学和光学性质 关键词: GaN薄膜 X射线光电子能谱 俄歇电子能谱 表面分析  相似文献   

11.
The porous optical film has higher threshold of laser-induced damage than densified films, for the study of mechanism of laser-induced damage of porous optical film with ordered pore structure. Porous anodic alumina (PAA) film with high transmittance on glass substrate has been prepared. Aluminum film was deposited on glass substrate by means of resistance and electron beam heat (EBH) evaporation. Porous alumina was prepared in oxalic acid solution under different anodizing conditions. At normal incidence, the optical transmittance spectrum over 300-1000 nm spectra region was obtained by spectrophotometer. SEM was introduced to analysis the morphology of the porous alumina film. The pore aperture increased with the increase of anodizing voltage, which resulted in a rapid decrease of the pore concentration and the optical thickness of porous alumina film. Damage morphology of porous alumina film is found to be typically defects initiated, and the defect is the pore presented on the film.  相似文献   

12.
倪海彬  王鸣  陈威 《物理学报》2012,61(8):84211-084211
研究了溶胶凝胶协同自组装制备大面积高质量SiO2反蛋白石结构薄膜的方法. 向单分散的聚苯乙烯(PS)胶体溶液中添加SiO2前驱物溶液,用垂直自组装法一步得到微球空隙中均匀填充有凝胶的 复合PS胶体晶体薄膜,在空气中烧结去除PS后得到SiO2反蛋白石结构薄膜.通过对添加前驱物溶液比例、 自组装温度以及烧结温度等参数的研究,用不同粒径的PS微球制备了不同孔径的高质量SiO2反蛋白石结构薄膜. 用扫描电子显微镜和X射线能量色散谱仪对制备得到的薄膜样品进行显微形貌和成分表征,并测试了其透射光谱. 结果表明:溶胶凝胶协同自组装法制备的SiO2反蛋白石结构薄膜大面积高度有序,孔径可以控制且选择范围宽; 薄膜的透射光谱带隙明显,带隙中心波长与理论计算结果相符.  相似文献   

13.
多孔氧化铝薄膜的制备和光学特性研究   总被引:5,自引:2,他引:3  
闫金良 《光子学报》2005,34(10):1530-1533
采用阳极氧化法制备了二维有序纳米孔氧化铝膜.研究了工艺参数对多孔薄膜有序性、孔径、膜厚度等的影响,测量了多孔氧化铝有序膜的光透过、光吸收和光发射等光学特性.结果表明,在波长360 nm附近多孔氧化铝有序膜的光透过谱线和光吸收谱线发生突变,波长大于360 nm时,光透过增强;波长小于360 nm时,光吸收增强.多孔氧化铝有序膜的光致发光强度和峰位与激发光波长有关,光致发光谱范围在340~600 nm.  相似文献   

14.
The effect of atomic disordering on the optical properties of Pt74.1Fe25.9 alloy, whose stoichiometry is close to that of Pt3Fe, has been investigated. The optical constants of ordered and plastically deformed alloys, which are, respectively, in the paramagnetic and ferromagnetic states, have been measured by the polarimetric method. The frequency dispersions of the permittivity, optical conductivity, and reflectivity, as well as the microscopic characteristics of conduction electrons (plasma and relaxation frequencies), have been calculated. The energy dependences of the optical conductivity are compared to the calculated energy-band structure of atomically ordered and disordered Pt3Fe compounds.  相似文献   

15.
The scanning force microscope (SFM) was used to investigate morphology of poly(ethylene oxide) (PEO) and poly(acrylic acid) (PAA) blend. The effect of solvent and dewetting in surface structure of PEO film was reported. The results manifested that the crystallization of PEO could be suppressed completely in ultrathin region via using chloroform as a solvent, and the branched-like crystallization was recovered after dewetting. Also, the effect of thickness, the ratio of PEO/PAA and dewetting in surface morphology of PEO-PAA blend films were investigated. These results showed that the crystallization was highly dependent on the ratio of PEO/PAA and the thickness of blend film. Furthermore, we assembled the PEO/PAA layer-by-layer film by spin-casting method for the first time, which exhibited highly efficiency. As a complementary tool, we also used lateral force microscopy (LFM) to explore surface information of these films. The result was indicative of interfacial constraints in ultrathin region, and also was supported by the results showing the spin-casting PEO/PAA blends rather than heterogeneous mixture.  相似文献   

16.
In this review, we will report a series of investigations on the homemade homogeneous magnetic fluids. The most spectacular property discussed in our research is the ordered structure of the magnetic columns formed in the magnetic fluid thin film under the influence of the external magnetic field, either perpendicular or parallel to the film surface. It is worth noting that the ordered structure can be manipulated by changing the control parameters. This reveals the variability of the ordered structure. With the ordered structures, some significant magneto-optical characteristics such as magnetochromatics, birefringence, and field-dependent transmittance are generated. These optical properties form the groundwork for further development of related optical devices by using the homogeneous magnetic fluid films.  相似文献   

17.
Using complementary techniques, namely X-ray fluorescence (XRF) and X-ray photoelectron spectroscopy (XPS), we present a comparative study of the bulk and surface composition in device grade CuGaSe2 (CGSe) thin films. The films were deposited in two stages by an open-tube chemical vapor deposition (CVD) process. The first stage leads to a nearly stoichiometric polycrystalline CGSe film of approximately 1.5 μm thickness. During the second stage the film is annealed in a Ga- and Se-rich atmosphere. While the XRF-data show a nearly stoichiometric integrated film composition, the surface composition, as determined by XPS analysis, is Cu-poor, pointing towards a highly non-stoichiometric surface layer. In addition, sodium was found at the film surfaces. The data are discussed in the framework of an ordered defect compound formation and the formation of a (Cu,Na)–Ga–Se compound at the surface of the CuGaSe2 films. Complementary ultraviolet photoelectron- and inverse photoelectron spectroscopy investigations of the film surface derive a widening of the surface energy band gap up to 2.2 eV in comparison with a bulk energy band gap around 1.65 eV (obtained by optical transmission analysis). The observed data are consistent with our model of a two layer film structure containing a defect-rich near-surface region and a defect-poor bulk.  相似文献   

18.
采用二次阳极氧化法,制备了多孔氧化铝模板。在真空背景下,用脉冲激光沉积法,在多孔氧化铝模板上沉积一层硅,制成了硅与多孔氧化铝的复合膜,然后用盐酸将多孔氧化铝模板完全腐蚀掉,制备均匀分布着硅纳米线的硅膜。用扫描电子显微镜、X射线衍射、光致发光对纳米硅的结构和光学性质进行了测试分析。结果表明:硅纳米线的直径约为67.5nm,长度约为100nm,数密度约1011/cm2。光致发光谱是可见光范围内的一个宽发射峰,上面叠加了许多具有精细结构的尖峰,尖峰之间的波长间隔不相等,但能量间隔相等。分析了样品的结构特点,利用量子限制模型和表面发光中心模型对光谱进行了解释,提出了一个新的能级模型,求出了各个尖峰对应激发态能级的量子数。为探讨纳米硅的发光机制和实现硅发光器件的制备提供了实验依据。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号