Sensitive light-scattering detection–magnetophoretic acceleration mass analysis of single microparticles in an atmosphere

Optically detected magnetophoretic acceleration mass analysis of an individual micro-particle in an atmosphere has been remarkably improved in sensitivity by using a reflective microscope objective, by which forward scattered light from a particle could be effectively collected. From the light-scattering simulation, the detection limit for the radius of a micro-particle was estimated to be smaller than 0.4 μm, and about 60 times intensity enhancement was observed for a polystyrene particle with a radius of 2.8 μm. For both paramagnetic and diamagnetic micro-particles, the mass magnetic susceptibility and the relaxation time could be determined without knowing any parameters of the particles. From the relaxation time, the mass of a particle was obtained if the radius or the density of the particle was known. For a test sample silica particles were used to adsorb paramagnetic dysprosium(III), the surface concentration of dysprosium(III) on a single particle could be successfully determined by use of this method.     

Separation of micro and sub-micro diamagnetic particles in dual ferrofluid streams based on negative magnetophoresis

In the present study, we numerically demonstrate an approach for separation of micro and sub-micro diamagnetic particles in dual ferrofluid streams based on negative magnetophoresis. The dual streams are constructed by an intermediate sheath flow, after which the negative magnetophoretic force induced by an array of permanent magnets dominates the separation of diamagnetic particles. A simple and efficient numerical model is developed to calculate the motions of particles under the action of magnetic field and flow field. Effects of the average flow velocity, the ratio of sheath fluid flow to sample fluid flow, the number of the magnet pair as well as the position of magnet pair are investigated. The optimal parametric condition for complete separation is obtained through the parametric analysis, and the separation principle is further elucidated by the force analysis. The separation of smaller micro and sub-micro diamagnetic particles is finally demonstrated. This study provides an insight into the negative magnetophoretic phenomenon and guides the fabrication of feasible, low-cost diagnostic devices for sub-micro particle separation.     

微流控芯片液滴生成与检测技术研究进展

微流控芯片液滴技术是一种操控微小体积液体的新技术,既可实现高通量微观样本的生成及控制,也可进行独立液滴的操作.分散的微液滴单元可作为理想的微反应器,在生物医药中的药物筛选、材料筛选和高附加值微颗粒材料合成领域展现出巨大的应用潜力.液滴微流控芯片是利用流体剪切力的改变,使互不相溶的两相流体在其界面处生成稳定、有序的液滴,...     

Experimental investigation of droplet acceleration and collision in the gas phase in a microchannel

We developed a novel microfluidic system, termed a micro-droplet collider, by utilizing the spatial-temporal localized liquid energy to realize chemical processes, which achieved rapid mixing between droplets having a large volume ratio by collision. In this paper, in order to clarify the characteristics of the micro-droplet collider, dynamics of droplet acceleration, stationary motion and collision in the gas phase in a microchannel were experimentally investigated with visualized images using a microscope equipped with a high-speed camera. The maximum velocity of 450 mm s(-1) and acceleration of 1500 m s(-2) of a 1.6 nL water droplet were achieved at an air pressure of 100 kPa. Measurement results of dynamic contact angles of droplets indicated that wettability of the surface played an important role in the stability of droplet acceleration and collision. We found that the bullet droplet penetrated into the target droplet at collision, which differed from bulk scale. The deformation of the droplet was strongly suppressed by the channel structure, thus stable collision and efficient utilization of the droplet energy were possible. These results are useful for estimating the localized energy, for improving the system in order to realize extreme performance, and for extending the applications of microfluidic devices.     

Measurement of dielectrophoretic mobility of single micro-particles in a flow channel

A new device to measure the dielectrophoretic mobility alpha of a single micro-particle in a micro-flow system has been proposed. From the velocity analysis of the micro-particle flowing between a pair of parabolic electrodes, the value of alpha could be obtained.     

Capillary magnetophoresis of human blood cells and their magnetophoretic trapping in a flow system

The performance of a capillary magnetophoretic device was improved by enhancing the magnetic field gradient using a pair of small iron tips attached to the Nd-Fe-B magnets. The magnetophoretic intensity, B(dB/dx), was determined as a function of distance along the gap between the tips from the magnetophoretic velocity of a 3 microm polystyrene microparticle in 0.6 M manganese(II) chloride solution. The maximum intensity was increased 4.5 times by the attached iron pieces. The magnetophoresis of a single human blood cell in 0.1 M manganese(II) solution was studied by this method and its magnetic susceptibility was estimated. Magnetophoretic trapping of red blood cells was demonstrated under counter-current flow conditions in the capillary.     

Design and operation of magnetophoretic systems at microscale: Device and particle approaches

Combining both device and particle designs are the essential concepts to be considered in magnetophoretic system development. Researcher efforts are often dedicated to only one of these design aspects and neglecting the interplay between them. Herein, to bring out importance of the idea of integration between device and particle, we reviewed the working principle of magnetophoretic system (includes both device and particle design concepts). Since, the magnetophoretic force is influenced by both field gradient and magnetization volume, hence, accurate prediction of the magnetophoretic force is relying on the availability of information on both parameters. In device design, we focus on the different strategies used to create localized high-field gradient. For particle design, we emphasize on the scaling between hydrodynamic size and magnetization volume. Moreover, we also briefly discussed the importance of magnetoshape anisotropy related to particle design aspect of magnetophoretic systems. Next, we illustrated the need for integration between device and particle design using microscale applications of magnetophoretic systems, include magnetic tweezers and microfluidic systems, as our working example. On the basis of our discussion, we highlighted several promising examples of microscale magnetophoretic systems which greatly utilized the interplay between device and particle design. Further, we concluded the review with several factors that possibly resulted in the lack of research efforts related to device and particle design integration.     

Spreading of a fluid phase on a spherical surface

The adsorption between a liquid drop and a micro-particle in an air or an air bubble and a micro-particle in water is dominated by liquid-solid or air-solid interfacial tension and wetting area of the liquid or air on the particle surface. The wetting area is determined by the spreading of the liquid drop or the bubble on the micro-particle. To explore this spreading, a wetting model of a fluid phase on a spherical particle was built. According to the theoretical results, the contact angle is constant when a fluid phase spreads on a spherical solid surface; the micro-particle can not submerge under a fluid when only interfacial tensions are involved and the wetting is not a complete wetting. The corresponding experiments were performed to confirm the theoretical results.     

Brownian motion-magnetophoresis of nano/micro-particles

A new magnetophoresis method to determine the magnetic susceptibility of single nano/microparticles was developed by applying Brownian motion analysis to determine the size of the particle. This method could measure simultaneously both the magnetophoretic velocity and the radius of the identical single nano/microparticles, which are necessary for the determination of the magnetic susceptibility of the particle. The advantage of this method was demonstrated by the measurement of the diamagnetic susceptibilities of polystyrene particles 500 nm-3 μm in diameter in a paramagnetic 0.5 M manganese(ii) chloride solution under a high magnetic field gradient of 5180 T(2) m(-1) generated by a small magnetic circuit.     

Spontaneous and deflected drift-trajectories in orthogonal acceleration time-of-flight mass spectrometry

Orthogonal acceleration is a method for gating ions from an ion beam into a time-of-flight (TOF) mass spectrometer. The technique involves a pulsed electric field to apply acceleration directed orthogonally to an ion beam. This approach is useful for coupling continuous ion sources to TOF mass analyzers. Most instruments of this type, which have been described in the literature, use steering electrodes after the orthogonal acceleration step. Those velocity components of ions originating from the ion beam velocity are minimized so that the deflected drift-trajectory is parallel to a transverse flight tube. In an alternative geometry the ion beam velocity is conserved and the drift-trajectory after the orthogonal acceleration step is spontaneous. The differences between the space-time focusing ability with spontaneous and deflected drift-trajectories are discussed and investigated. Trajectory calculations indicate that deflection fields placed after the orthogonal acceleration step distort the ion packet because, in this geometry, the flight-time to the detector is dependent on the position that the ions enter the steering optics. Increasing the duty-cycle efficiency by sampling longer sections of the continuous ion beam leads to a degradation of resolving power. Employing a spontaneous drift-trajectory after orthogonal acceleration provides the advantage that the arrival time spread for isobaric ions is, in principle, independent of the length of the ion beam sampled. The major implication of these findings is that simultaneously optimized sensitivity and resolving power may not be achievable with the deflected drift-trajectory instruments. The calculations are in agreement with results from the published data of a number of groups who have built instruments based on the orthogonal acceleration principle.     

Magnetophoretic velocity of microorganic droplets adsorbed by dysprosium(III) laurate in water

By using an improved apparatus for the observation of magnetophoresis, the magnetophoretic velocity of 2-fluorotoluene droplets including lauric acid was measured in aqueous dysprosium(III) solution. The magnetophoretic velocity of pure 2-fluorotoluene droplets was proportional to the square of the radius. On the other hand, the velocity of the organic droplets including lauric acid in the dysprosium(III) solution showed a deviation from the square radius relationship, more remarkably in smaller droplets than 2 microm in radius. These results indicated that the dysprosium(III)-laurate complex was formed at the liquid-liquid interface. This study is the first report on the detection of the interfacial complex by the magnetophoresis of the microdroplet.     

An accurate model for sample droplet acceleration in an air—acetylene flame

The experimentally observed velocity of an aerosol droplet in an air—acetylene flame is compared to the velocity calculated through a new mathematical model. The experimental droplet velocity is measured by means of stroboscopic photography of a stream of individual droplets sent into a flame at a known frequency and traveling very reproducible trajectories. Because the temporal spacing between these droplets is known, a measure of the instantaneous droplet location enables their velocity to be calculated. The droplet acceleration model was modified by incorporating into it a radially changing flame rise velocity, which was assumed constant in earlier treatments. Excellent agreement is found between calculated and measured droplet acceleration in the flame.     

Simultaneous measurement of the migration velocity and adsorption force of micro-particles using an electromagnetophoretic force under a high magnetic field.

A simultaneous measurement technique for determining the migration velocity of a micrometer-sized particle in a capillary and the adsorption force to the inner surface of the capillary has been proposed. This technique is based on an electromagnetophoretic force being exerted on a micro-particle in an electrolyte solution, which is governed mainly by the electromagnetic buoyancy, when a homogeneous magnetic field is applied at a right angle to the electric current through the medium. By the electromagnetic buoyancy, micro-particles such as polystyrene, carbon and yeast were migrated perpendicular to the direction of the electric current and reached a fused-silica wall. A switching of the current direction could desorb the particle from the wall, and allowed to calculate the detaching force from the desorbing current. The migration velocity normalized to the size in the magnetic field of 10 T was increased in the order of yeast, carbon and polystyrene, while reflecting the decreasing order of the apparent conductivity of the particles. The desorption force could be measured up to 1 nN with a sensitivity of pN. The observed interaction forces of polystyrene and carbon were in the range of 250-600 pN with large deviations.     

Microfluidic magnetophoretic separations of immunomagnetically labeled rare mammalian cells

Immunomagnetic isolation and magnetophoresis in microfluidics have emerged as viable techniques for the separation, fractionation, and enrichment of rare cells. Here we present the development and characterization of a microfluidic system that incorporates an angled permanent magnet for the lateral magnetophoresis of superparamagnetic beads and labeled cell-bead complexes. A numerical model, based on the relevant transport processes, is developed as a design tool for the demonstration and prediction of magnetophoretic displacement. We employ a dimensionless magnetophoresis parameter to efficiently investigate the design space, gain insight into the physics of the system, and compare results across the vast spectrum of magnetophoretic microfluidic systems. The numerical model and theoretical analysis are experimentally validated by the lateral magnetophoretic deflection of superparamagnetic beads and magnetically labeled breast adenocarcinoma MCF-7 cells in a microfluidic device that incorporates a permanent magnet angled relative to the flow. Through the dimensionless magnetophoresis parameter, the transition between regimes of magnetophoretic action, from hydrodynamically dominated (magnetic deflection) to magnetically dominated (magnetic capture), is experimentally identified. This powerful tool and theoretical framework enables efficient device and experiment design of biologically relevant systems, taking into account their inherent variability and labeling distributions. This analysis identifies the necessary beads, magnet configuration (orientation), magnet type (permanent, ferromagnetic, electromagnet), flow rate, channel geometry, and buffer to achieve the desired level of magnetophoretic deflection or capture.     

Rapid Multiphase Flow Dynamics Mapped by Single‐Shot MRI Velocimetry

A new, fast magnetic resonance imaging (MRI) method is described and applied to map flow fields in systems with internal velocities rapidly varying along the streamlines. While conventional MRI techniques encode the velocity information in a preparatory period prior to the imaging acquisition module, our technique repeatedly refreshes the velocity encoding during a single‐shot imaging sequence. In this way, the maximum acceleration responsible for velocity variation of the molecules is increased by up to two orders of magnitude compared to standard procedures. Besides being compatible with high acceleration, this pulse sequence is suited to acquiring in a single scan the multiple velocity images required to construct a full velocity vector map. The power of this new methodology is demonstrated by following the internal dynamics of toluene droplets levitating in a counterflow of water during mass transfer of acetone from the water phase into the drop in the presence of surface‐active impurities. The dramatic reduction in measurement time allows visualization for the first time of the important impact of even small concentrations of acetone on accumulation of surfactants at the drop’s surface.     

Three‐dimensional printed magnetophoretic system for the continuous flow separation of avian influenza H5N1 viruses

As a result of the low concentration of avian influenza viruses in samples for routine screening, the separation and concentration of these viruses are vital for their sensitive detection. We present a novel three‐dimensional printed magnetophoretic system for the continuous flow separation of the viruses using aptamer‐modified magnetic nanoparticles, a magnetophoretic chip, a magnetic field, and a fluidic controller. The magnetic field was designed based on finite element magnetic simulation and developed using neodymium magnets with a maximum intensity of 0.65 T and a gradient of 32 T/m for dragging the nanoparticle–virus complexes. The magnetophoretic chip was designed by SOLIDWORKS and fabricated by a three‐dimensional printer with a magnetophoretic channel for the continuous flow separation of the viruses using phosphate‐buffered saline as carrier flow. The fluidic controller was developed using a microcontroller and peristaltic pumps to inject the carrier flow and the viruses. The trajectory of the virus–nanoparticle complexes was simulated using COMSOL for optimization of the carrier flow and the magnetic field, respectively. The results showed that the H5N1 viruses could be captured, separated, and concentrated using the proposed magnetophoretic system with the separation efficiency up to 88% in a continuous flow separation time of 2 min for a sample volume of 200 μL.     

In situ hydrodynamic lateral force calibration of AFM colloidal probes

Lateral force microscopy (LFM) is an application of atomic force microscopy (AFM) to sense lateral forces applied to the AFM probe tip. Recent advances in tissue engineering and functional biomaterials have shown a need for the surface characterization of their material and biochemical properties under the application of lateral forces. LFM equipped with colloidal probes of well-defined tip geometries has been a natural fit to address these needs but has remained limited to provide primarily qualitative results. For quantitative measurements, LFM requires the successful determination of the lateral force or torque conversion factor of the probe. Usually, force calibration results obtained in air are used for force measurements in liquids, but refractive index differences between air and liquids induce changes in the conversion factor. Furthermore, in the case of biochemically functionalized tips, damage can occur during calibration because tip-surface contact is inevitable in most calibration methods. Therefore, a nondestructive in situ lateral force calibration is desirable for LFM applications in liquids. Here we present an in situ hydrodynamic lateral force calibration method for AFM colloidal probes. In this method, the laterally scanned substrate surface generated a creeping Couette flow, which deformed the probe under torsion. The spherical geometry of the tip enabled the calculation of tip drag forces, and the lateral torque conversion factor was calibrated from the lateral voltage change and estimated torque. Comparisons with lateral force calibrations performed in air show that the hydrodynamic lateral force calibration method enables quantitative lateral force measurements in liquid using colloidal probes.     

Tunable magnetophoretic method for distinguishing and separating wear debris particles in an Fe-PDMS-based microfluidic chip

Wear debris analysis provides an early warning of mechanical transmission system aging and wear fault diagnosis, which has been widely used in machine health monitoring. The ability to detect and distinguish the ferromagnetic and nonmagnetic debris in oil is becoming an effective way to assess the health status of machinery. In this work, an Fe-poly(dimethylsiloxane) (PDMS)-based magnetophoretic method for the continuous separation of ferromagnetic iron particles by diameter and the isolation of ferromagnetic particles and nonmagnetic particles with similar diameter by type is developed. The particles experience magnetophoretic effects when passing through the vicinity of the Fe-PDMS where the strongest gradient of the magnetic fields exists. By choosing a relatively short distance between the magnet and the sidewall of the horizontal main channel and the length of Fe-PDMS with controlled particles flow rate, the diameter-dependent separation of ferromagnetic iron particles, that is, smaller than 7 µm, in the range of 8–12 µm, and larger than 14 µm, and the isolation of ferromagnetic iron particles and nonmagnetic aluminum particles based on opposite magnetophoretic behaviors by types are demonstrated, providing a potential method for the detection of wear debris particles with a high sensitivity and resolution and the diagnostic of mechanical system.     

基于磁泳的生物分离分析技术

利用磁场诱导的微粒运动即磁泳对磁响应性粒子进行精细分离,是近年来发展起来的选择性分离细胞和高分子量核酸的有效技术。本文在阐明磁泳分离原理的基础上,介绍了磁泳分离的分流薄层分级技术、四极磁场流动分离技术和微芯片上的自由流磁泳分离技术的装置构造、工作原理及其在生物分离分析中的应用。     

基于磁泳的生物分离分析技术

利用磁场诱导的微粒运动即磁泳对磁响应性粒子进行精细分离,是近年来发展起来的选择性分离细胞和高分子量核酸的有效技术。本文在阐明磁泳分离原理的基础上,介绍了磁泳分离的分流薄层分级技术、四极磁场流动分离技术和微芯片上的自由流磁泳分离技术的装置构造、工作原理及其在生物分离分析中的应用。