Effect of the alkyl chain of quaternary ammonium cationic surfactants on corrosion inhibition in hydrochloric acid solution

In this study, the effect of the alkyl chain of quaternary ammonium cationic surfactants on corrosion inhibition in hydrochloric acid (HCl) solution was investigated by using dodecyl trimethyl ammonium chloride (DTAC), tetradecyl trimethyl ammonium chloride (TTAC), cetyl trimethyl ammonium chloride (CTAC), and octadecyl trimethyl ammonium chloride (OTAC) as corrosion inhibitors to uncover their structure–efficiency relationships. The effect of the alkyl chain of quaternary ammonium cationic surfactants on corrosion inhibition in HCl solution was studied under different conditions, such as corrosion inhibitor concentration, temperature, and acidity, and this was done using the weightlessness method. The results obtained show that these inhibitors have high corrosion inhibition effect on A₃ steel, and the corrosion inhibition efficiency is dependent on the length of the alkyl chain. At the same concentration, the longer the alkyl chain, the weaker the corrosion inhibition effect. When the temperature was 50 °C and the concentration of corrosion inhibitor was 70 mg/L, the corrosion inhibition efficiency order of the four cationic surfactants was DTAC > TTAC > CTAC > OTAC. Besides, the experimental results obtained show that the adsorption of the inhibitor on the A₃ steel surface conforms to the Langmuir type isotherm, and then the corresponding adsorption thermodynamic parameters were obtained according to these parameters. It was observed that ΔH, ΔS, and E_a increased with increase in the length of the alkyl chain. The adsorption of the inhibitor on the steel surface is an exothermic, spontaneous, entropy process.     

Co-solvent effects on drag reduction, rheological properties and micelle microstructures of cationic surfactants

Some quaternary cationic surfactants, when mixed with a counterion, are known to self-assemble into threadlike micelles in water. Such behavior causes drastic changes in rheological properties of even very dilute solutions, allowing them to be used as drag reducing agents (DRA) in turbulent pipe flow circulating systems, such as district cooling/heating systems. Surfactant self-assembly is a physicochemical phenomenon whose character depends on surfactant nature and concentration, nature of the solvent, temperature and type and concentration of counterions. This study investigates drag reduction (DR) and rheological properties of two cationic surfactants, Ethoquad O/12 (oleyl bis(hydroxyethyl)methylammonium chloride) and Ethoquad O/13 (oleyl tris(hydroxyethyl) ammonium acetate), with excess salicylate counterion (NaSal), in mixed solvents containing 0 to 28 wt% ethylene glycol (EG) and water. The addition of EG to the solvent had greater effects on solutions' DR ability, shear viscosity, apparent extensional viscosity and viscoelasticity at 25 degrees C than at approximately 0 degrees C. Cryo-TEM images show threadlike micelle in these systems. DR at low temperatures in solutions containing moderate amount of EG can be utilized in a new approach to energy saving in district cooling systems using EG-water based mixtures as the cooling fluids.     

Interaction between the water soluble poly{1,4-phenylene-[9,9-bis(4-phenoxy butylsulfonate)]fluorene-2,7-diyl} copolymer and ionic surfactants followed by spectroscopic and conductivity measurements

The interaction has been studied in aqueous solutions between a negatively charged conjugated polyelectrolyte poly{1,4-phenylene-[9,9-bis(4-phenoxybutylsulfonate)]fluorene-2,7-diyl} copolymer (PBS-PFP) and several cationic tetraalkylammonium surfactants with different structures (alkyl chain length, counterion, or double alkyl chain), with tetramethylammonium cations and with the anionic surfactant sodium dodecyl sulfate (SDS) by electronic absorption and emission spectroscopy and by conductivity measurements. The results are compared with those previously obtained on the interaction of the same polymer with the nonionic surfactant C12E5. The nature of the electrostatic or hydrophobic polymer-surfactant interactions leads to very different behavior. The polymer induces the aggregation with the cationic surfactants at concentrations well below the critical micelle concentration, while this is inhibited with the anionic SDS, as demonstrated from conductivity measurements. The interaction with cationic surfactants only shows a small dependence on alkyl chain length or counterion and is suggested to be dominated by electrostatic interactions. In contrast to previous studies with the nonionic C12E5, both the cationic and the anionic surfactants quench the PBS-PFP emission intensity, leading also to a decrease in the polymer emission lifetime. However, the interaction with these cationic surfactants leads to the appearance of a new emission band (approximately 525 nm), which may be due to energy hopping to defect sites due to the increase of PBS-PFP interchain interaction favored by charge neutralization of the anionic polymer by cationic surfactant and by hydrophobic interactions involving the surfactant alkyl chains, since the same green band is not observed by adding either tetramethylammonium hydroxide or chloride. This effect suggests that the cationic surfactants are changing the nature of PBS-PFP aggregates. The nature of the polymer and surfactant interactions can, thus, be used to control the spectroscopic and conductivity properties of the polymer, which may have implications in its applications.     

Properties of the Nanoscale Hydrophilic Cationic Pigment Based on Quaternary Surfactant

Dispersions of four nanoscale hydrophilic cationic pigments were prepared by micro jet milling process, in which the dodecyl trimethyl ammonium chloride (DTAC), tetradecyl trimethyl ammonium chloride (TDAC), hexadecyl trimethyl ammonium chloride (CTAC), and octadecyl trimethyl ammonium chloride (STAC) were used as the dispersers respectively. Zeta potential, particle size, viscosity and dispersion stability were tested. The effect of the hydrophobic chain of cationic quaternary surfactant on pigment dispersion's properties was discussed. The results showed that good dispersion effects were obtained when the hydrophobic chain were 14 or 16.     

羧甲基淀粉与烷基二甲基苄基氯化铵的相互作用研究

通过电导法、荧光法、粒度法等方法研究了羧甲基淀粉与3种不同碳数烷基二甲基苄基氯化铵之间的相互作用。结果表明,羧甲基淀粉与长链烷基二甲基苄基氯化铵在小于单纯表面活性剂临界胶束浓度（cmc）1～2个数量级的浓度下发生复合,并产生沉淀。当表面活性剂烷基链增加且浓度增大时,表面活性剂长碳链间的疏水作用及与羧甲基淀粉间的疏水作用...     

Critical micelle concentrations and interaction parameters of aqueous binary surfactant:ionic surfactant mixtures

A relationship between the critical micelle concentration (CMC) and the surfactant's composition in the bulk phase that supercedes Rubingh's method is derived for aqueous mixtures of ionic surfactants by considering the interaction between a micellar ionic aggregate and the diffusion layer around it. To test this approach we measured the CMCs of solutions of cationic surfactant mixtures and also of alkylammonium dodecanesulfonate mixtures. In the absence of controlled concentration of the counterion, the CMCs do not fit Clint's equation, but CMCs measured at a constant counterion concentration fit it approximately. The interaction parameter in the theory of regular solutions is obtained from the relationship between the micellar and bulk compositions. The values of the interaction parameter and the concentration exponent change with the hydrophobicity of the counterion in mixtures of alkylammonium dodecanesulfonates. The micellar composition of dodecylammonium chloride and dodecyltrimethylammonium chloride mixtures depends very little on the counterion concentration. The interaction energy between the ammonium and trimethylammonium groups of the cationic surfactants is about -0.05kT on average and depends on the concentration of the counterion.     

Synthesis and analytical properties of the polymerized surfactant pposa

A new low-polymer surfactant, poly(propylene oxide)--stearyldimethylammonium chloride (PPOSA) has been synthesized. It contains a polyglycol main chain and quaternary ammonium branched chains. Investigation of the surface-active properties of PPOSA showed that as a sensitizing and solubilizing reagent for spectrophotometric analysis it possesses some of the characteristics of both cationic and non-ionic surfactants. The surfactant shows a sensitizing effect superior or equal to that of classical surfactants commonly used in analytical chemistry. Use of PPOSA leads to development of some excellent micellar spectrophotometric procedures for determining trace metals.     

有机改性膨润土对己唑醇水悬浮体系物理稳定性的影响

利用4种季铵盐阳离子表面活性剂（十二烷基二甲基苄基氯化铵(1227)、十四烷基二甲基苄基氯化铵(1427)、十六烷基三甲基氯化铵(1631)和十八烷基三甲基氯化铵(1831)）分别对钠基膨润土（Na-Ben）进行有机改性,制得4种有机膨润土（1227-Ben、1427-Ben、1631-Ben和1831-Ben）并进行了红外光谱及X射线分析,考察了4种有机膨润土在水中的悬浮性能及对5%己唑醇水悬体系物理稳定性能的影响。 FT-IR及XRD分析结果表明,供试季铵盐阳离子的有机碳链均进入到膨润土的片层间。 水中悬浮性能测定实验表明,1831-Ben在水中悬浮性能相对较好,而其它3种均不理想,特别是1227-Ben和1427-Ben表现出强烈的斥水现象。 沉降试验表明,有机膨润土的使用有助于5%己唑醇水悬浮剂物理稳定性的提高,其中用1831-Ben制备出的水悬浮体系的物理稳定性明显优于其它3种,制剂析水率最低,屈服值与粘度最大,体系悬浮率最高,可见1831-Ben可以用作5%己唑醇水悬浮剂的抗沉降剂。     

Interaction of cationic surfactants with carboxymethylcellulose in aqueous media

We have examined the polymer-surfactant interaction in mixed solutions of the cationic surfactants, i.e., dodecyltrimethylammonium chloride, dodecyltrimethylammonium bromide, tetradecyltrimethylammonium bromide, hexadecyltrimethylammonium bromide, tetradecyltriphenylphosphonium bromide, and tetradecylpyridinium bromide and a semiflexible anionic polyelectrolyte carboxymethylcellulose in water and aqueous salt solutions by various techniques: tensiometry, viscosimetry or ion-selective electrode method, and dynamic light scattering. We have investigated the effect of varying surfactant chain length, head group size, counterion, and ionic strength on the critical aggregation concentration (CAC) of mixed polymer surfactant systems and the collapse of the polymer molecule under different solution conditions. The CAC decreases with increasing alkyl chain length. Above a certain surfactant concentration, mixed aggregates start growing until their macroscopic phase separation. The growth is more rapid with greater surfactant tail length and with increasing head group size. This is attributed in both cases to the increasing hydrophobic interaction between polymer and surfactant. Among surfactants with monovalent halide counterions, iodide induces the strongest binding, reflected by the onset of growth of the mixed aggregates at low surfactant concentration. This is perhaps related to the decreasing hydration of the counterion from chloride to iodide. The surfactant concentration at which the viscosity of the solution starts to decrease sharply is smaller than the CAC, and probably reflects polymer chain shrinkage due to noncooperative binding.     

Studies of Interfacial Activities of Four Kinds of Surfactants at Oil/Water Interface

This article aims to compare the interfacial activities of different kinds of surfactants in the same oil/water system. The anionic surfactants of alkylbenzene sulfonates, the polyoxyethylenated nonionic surfactants, the cationic surfactants of alkyl trimethyl ammonium chlorides, and the zwitterionic surfactants of alkyl hydroxyl sulfobetaines were used, and the interfacial tensions of the surfactant solutions against kerosene at different NaCl concentrations were measured. It is found that the interfacial activities of the alkylbenzene sulfonates are high and ultralow interfacial tensions (<0.01 mN/m) can be obtained at proper salinities. While, the nonionic surfactants have relatively low interfacial activities and the minimum tensions are around 0.01 mN/ms. The salinity scanning curves of the alkylbenzene sulfonates and nonionic surfactants decrease first, then increase, showing their interfacial activities can be changed by the salinity effectively. The cationic and zwitterionic surfactants have very low interfacial activities, of which all the tensions are higher than 0.1 mN/ms and are hard to be changed by the salinity. The experimental results may have important reference values for enhanced oil recovery.     

Forces between glass surfaces in mixed cationic-zwitterionic surfactant systems

We report atomic force microscopy (AFM) measurements of the forces between borosilicate glass solids in aqueous mixtures of cationic and zwitterionic surfactants. These forces are used to determine the adsorption of the surfactant as a function of the separation between the interfaces (proximal adsorption) through the application of a Maxwell relation. In the absence of cationic surfactant, the zwitterionic surfactant N-dodecyl-N,N-dimethyl-3-ammonio-1-propanesulfonate (DDAPS) undergoes little adsorption to glass at concentrations up to about 2/3 critical micelle concentration (cmc). In addition, DDAPS does not have much effect on the forces over the same concentration range. In contrast, the cationic surfactant dodecylpyridinium chloride (DPC) does adsorb to glass and does affect the force between glass surfaces at concentrations much lower than the cmc. In the presence of a small amount of DPC (0.05 mM = cmc/300), the net force between the glass surfaces is quite sensitive to the solution concentration of DDAPS. A model-independent thermodynamic argument is used to show that the surface excess of DDAPS depends on the separation between the glass interfaces when the cationic surfactant is present and that the surface excess of the cationic surfactant is more sensitive to interfacial separation in the presence of the zwitterionic surfactant. The change in adsorption of the zwitterionic surfactant is explained in terms of an intermolecular coupling between the long-range electrostatic force acting on the cationic surfactant and the short-range hydrophobic interaction between the alkyl chains on the cationic and zwitterionic surfactants. The adsorptions of cationic and zwitterionic surfactants in mixtures were measured independently and simultaneously by attenuated total internal reflection infrared spectroscopy (ATR-IR). The adsorption of the zwitterionic surfactant is enhanced by the presence of a small amount of cationic surfactant.     

Spin probe study on the interaction of chitosan-derived polymer surfactants with lipid membrane

Chitosan-derived polymer surfactants, sulfated N-acyl-chitosan (S-Cn-Chitosan), were synthesized and compared with commonly used low-molecular-weight surfactants, sodium dodecyl sulfate (SDS), dodecyltrimethyl ammonium chloride (DTAC), and octaethyleneglycol mono n-dodecyl ether (BL8SY), in their interaction with a lipid membrane using a spin probe method. A suspension of dipalmitoylphosphatidyl-choline (DPPC) spin-labeled strongly (10%) with a spin probe, 1-palmitoyl-2-(12-doxyl) stearoyl-phosphatidylcholine, was mixed with the surfactant solutions. The dissolution time of the DPPC membrane was estimated from the peak height change vs time, which was caused by the decrease in spin-exchange interaction. The times were 2, 4, and 70 s for BL8SY, SDS, and DTAC and 1.2 and 8.8 h for S-C10-Chitosan and S-C14-Chitosan, respectively, showing that the dissolution of the lipid membrane with polymer surfactants was far slower than that with low-molecular-weight surfactants. In addition, the time depended on the length of the alkyl chains of the polymer surfactants. Simulations of the ESR spectra of the DPPC-surfactant systems containing small amounts of surfactants were carried out in order to examine how the membrane structure was changed by the incorporation of surfactant molecules. By this analysis, it was revealed that the rigidity of the membrane was decreased by the addition of low-molecular-weight surfactants in the order of DTAC>SDS>BL8SY, inverse to the order of dissolution times. S-Cn-Chitosan, in contrast, increased the rigidity of the membrane, suggesting that polymer surfactants adhered to the lipid membrane and tightly enfolded the riposome anchoring their alkyl chains.     

Effects of double-chained cationic surfactants n-dimethyldialkylammoniums on skin permeation of benzoic acid through excised guinea pig dorsal skin: comparison of their enhancement effects with hemolytic effects on erythrocytes

We examined the effects of the double-chained cationic surfactants dimethyidialkylammoniums (CH3)2N+ (CnH(2n+1))2 on the permeation of benzoic acid through excised guinea pig dorsal skin. Among five dimethyldialkylammoniums tested (n=10-18), dimethyldidecylammonium (n=10) had dose-dependent enhancement effects at concentrations of more than 20 microM. Compared with the marked enhancement effects of dimethyldialkylammoniums with relatively shorter alkyl chains, those of long-chain dimethyldialkylammoniums (n=16, 18) were much less. We compared the enhancement effects of these cationic surfactants on skin permeation with their hemolytic effects on guinea pig erythrocytes. Their enhancement effects corresponded to their hemolytic activity. The findings suggest that dimethyldialkylammoniums with relatively shorter alkyl chains, which form either vesicles with looser molecular packing or micelles and appear to be present as surfactant monomers in higher ratios than those with longer alkyl chains, favor the interaction with skin. Their enhancement mechanism is possibly similar to that of single-chained cationic surfactants.     

Electrokinetic chromatographic characterization of novel pseudo-phases based on N-alkyl-N-methylpyrrolidinium ionic liquid type surfactants

MEKC and linear solvation free energy relationships (LSFERs) have been used to characterize the solute distribution between water and self-assemblies formed from ionic liquid type mono-chain cationic surfactants containing a cyclic pyrrolidinium head group. Several features of the solvation environment afforded by these micellar solutions were found to be quite different from that of CTAB, a structurally analogous cationic surfactant with a conventional, acyclic quaternary ammonium head group. None of the LSFER coefficients were found to vary in any systematic way with increasing alkyl chain length for these unique surfactants. Overall, however, these surfactants display different behavior than do all known cationic detergents such as CTAB. In chemical terms, pseudo-phases formed by these N-alkyl-N-methylpyrrolidinium bromides interact more strongly with polar compounds and less strongly with compounds having nonbonding or pi-electrons and are more cohesive compared to the well-studied CTAB.     

Mixed micelles of polyethylene glycol (23) lauryl ether with ionic surfactants studied by proton 1D and 2D NMR

(1)H NMR chemical shift, spin-lattice relaxation time, spin-spin relaxation time, self-diffusion coefficient, and two-dimensional nuclear Overhauser enhancement (2D NOESY) measurements have been used to study the nonionic-ionic surfactant mixed micelles. Cetyl trimethyl ammonium bromide (CTAB) and sodium dodecyl sulfate (SDS) were used as the ionic surfactants and polyethylene glycol (23) lauryl ether (Brij-35) as the nonionic surfactant. The two systems are both with varying molar ratios of CTAB/Brij-35 (C/B) and SDS/Brij-35 (S/B) ranging from 0.5 to 2, respectively, at a constant concentration of 6 mM for Brij-35 in aqueous solutions. Results give information about the relative arrangement of the surfactant molecules in the mixed micelles. In the former system, the trimethyl groups attached to the polar heads of the CTAB molecules are located between the first oxy-ethylene groups next to the hydrophobic chains of Brij-35 molecules. These oxy-ethylene groups gradually move outward from the hydrophobic core of the mixed micelle with an increase in C/B in the mixed solution. In contrast to the case of the CTAB/Triton X-100 system, the long flexible hydrophilic poly oxy-ethylene chains, which are in the exterior part of the mixed micelles, remain coiled, but looser, surrounding the hydrophobic core. There is almost no variation in conformation of the hydrophilic chains of Brij-35 molecules in the mixed micelles of the SDS/Brij-35 system as the S/B increases. The hydrophobic chains of both CTAB and SDS are co-aggregated with Brij-35, respectively, in their mixed micellar cores.     

Hydrophobic terminal group of surfactant initiating micellization as revealed by 1H NMR spectroscopy

The critical aggregation concentration (CAC) of four with three kinds of conventional surfactants, namely, two cationic surfactants [hexadecyltrimethyl ammonium bromide (CTAB) and tetradecyltrimethyl ammonium bromide (TTAB)], one anionic surfactant [sodium dodecyl sulfate (SDS)], and a nonionic surfactant [Triton X-100 (TX-100)], were determined by variation of ¹H chemical shifts with surfactant concentrations. Results show that the CAC values of protons at different positions of the same molecule are different, and those of the terminal methyl protons are the lowest, respectively, which suggests that the terminal groups of the alkyl chains aggregates first during micellization. Measurement of the transverse relaxation time (T₂) of different protons in SDS also show that the terminal methyl protons start to decrease with the increase in concentration first, which supports the above mentioned tendency.     

Mixed micellar properties of cationic trimeric-type quaternary ammonium salts and anionic sodium n-octyl sulfate surfactants

The properties of quaternary ammonium salt-type cationic trimeric surfactants (m-2-m-2-m, m represents the carbon atom number in alkyl chain lengths of 8, 10, and 12) and oppositely charged anionic monomeric surfactant, sodium n-octyl sulfate (SOS), were characterized by employing several techniques such as static surface tension, fluorescence spectroscopy, and dynamic light-scattering measurements. The critical micelle concentrations (cmc) of m-2-m-2-m were much lower than those of the corresponding dimeric and monomeric surfactants, and decreased with increasing chain length. The addition of SOS to m-2-m-2-m solutions resulted in a further decrease of the cmc. The mixed surfactants showed higher efficiencies in lowering the surface tension than the individual surfactants. The fluorescence measurements suggested the formation of mixed micelles with a hydrophobic environment in the solutions even at lower concentrations. The dynamic light-scattering study indicated the presence of two different kinds of aggregates with different hydrodynamic diameters. The larger one was attributed to the mixed micelle of m-2-m-2-m and SOS. These results indicated a decline of the electrostatic repulsion between cationic head groups through the incorporation of anionic surfactant into the mixed surfactants.     

Sol–gel encapsulation of cresol red in presence of surfactants

Cresol Red (CR) pH indicator was encapsulated into silica network using the sol–gel process. Transparent monolithic disks of entrapped CR were obtained in the presence of cetyl trimethyl ammonium bromide (CTAB) or dodecyl dimethyl amino oxide (Genaminox LA,GLA) alkyl hydroxyethyl dimethyl ammonium chloride (HY, R = 12–14) and TX-100 surfactants. UV/VIS spectra showed that the encapsulated CR retains its structure in terms of its response to pH. At the neutral conditions it is found that the HY surfactant is considered as proton donor as favor the cationic form of the indicator, while CTAB surfactant favor the neutral, however GLA surfactant, the anionic form of CR is more favored because GLA has a zwitterionic head. The surfactant GLA with TEOS has shifted the equilibrium to the ionized form of CR due to the electrostatic interaction between the surfactant and the CR anion. Therefore their pH range is dependent on the nature of a surfactant used. It is found that the HY surfactant is more efficient as far as loading of CR is concern and it widened the working pH range.     

支链化阳离子和甜菜碱表面活性剂对聚四氟乙烯表面润湿性的影响

利用座滴法研究了支链化阳离子表面活性剂十六烷基羟丙基氯化铵(C₁₆GPC)和两性离子表面活性剂十六烷基羧酸甜菜碱(C₁₆GPB)在聚四氟乙烯(PTFE)表面上的吸附机制和润湿性质, 考察了表面活性剂浓度对表面张力、接触角、粘附张力、固液界面张力和粘附功的影响趋势. 研究发现, 低浓度条件下, 表面活性剂疏水支链的多个亚甲基基团与PTFE表面发生相互作用, 分子以平躺的方式吸附到固体界面; 支链化表面活性剂形成胶束的阻碍较大, 浓度大于临界胶束浓度(cmc)时, C₁₆GPC和C₁₆GPB分子在固液界面上继续吸附, 与PTFE作用的亚甲基基团减少, 分子逐渐直立, 固液界面自由能(γ_sl)明显降低. 对于支链化的阳离子和甜菜碱分子, 接触角均在浓度高于cmc后大幅度降低.