A 168-W high-power single-frequency amplifier in an all-fiber configuration

We present a high-power,single-frequency,narrow linewidth fiber amplifier based on master oscillator power amplification chains in an all-fiber configuration.The effect of the delivery fiber on the maximum output power is studied.A home-made 1064-nm seed laser with a 20-kHz linewidth is boosted to 129 W,and limited by stimulated Brillouin scattering(SBS) when the delivery fiber is 1.2 m long.By shortening the delivery fiber length to 0.7 m,the SBS threshold is increased efficiently and the maximum output power rises to 168 W with an 82.9% power conversion efficiency.The experimental results indicate that the output power can be further raised by shortening the delivery fiber length and increasing the pump power.     

大功率单频多芯光纤放大器中抑制受激布里渊散射的分析

针对多芯光纤完善了描述抽运光、信号光和Stokes信号的速率方程组.考虑了温差对受激布里渊散射的影响,利用有限元法求解温度分布方程组,分析了前向和后向抽运方式、对流系数、Stokes初始功率、光纤掺杂粒子密度和光纤长度对受激布里渊散射增益的影响.研究表明：后向抽运方式在抑制受激布里渊散射方面具有明显优势;减小对流系数有助于抑制受激布里渊散射;提高光纤掺杂密度能够加强抑制受激布里渊散射,同时也有助于提高光纤放大器的斜率效率.比较了在相同最佳光纤长度条件下,单芯和19芯光纤放大器的最高工作温度和受激布里渊散射 关键词： 光纤放大器 受激布里渊散射 大功率 有限元法     

增益竞争双波长放大单频光纤放大器理论研究

引入增益竞争是抑制单频光纤放大器中受激布里渊散射(SBS)的有效方式. 在单频光纤放大器的基础上, 推导了描述增益竞争双波长放大单频掺镱双包层光纤放大器的稳态速率方程组, 建立了增益竞争双波长放大单频光纤放大器的理论模型; 利用建立的理论模型模拟分析了信号光波长间隔、 信号光种子功率比、 抽运方式和增益光纤长度等因素对放大器的单频激光输出 效率以及SBS抑制效果的影响.     

Investigation and applications of all-fiber brillouin ring resonator lasers

We examine the theoretical and experimental behavior of Brillouin ring resonator lasers (BRRL), highlighting differences between Brillouin scattering in ring resonators and long fiber lengths. The theory, which assumes that the nonlinear interaction is welldescribed by two coupled equations for the optical waves, agrees well with measured data. We examine the single and multimode behavior of BRRL and show how this may be usefully implemented in microwave signal generation, in Stimulated Brillouin Scattering gain studies, and to realize a new form of all-fiber frequency shifter.     

The 260-W coherent beam combining of two compact fibre amplifier chains

Coherent beam combining of two fibre amplifier chains with a total power of 260 W in a compact system using the stochastic parallel gradient descent (SPGD) algorithm is demonstrated. A 150 MHz linewidth fibre laser is built and introduced for high-power amplification to mitigate stimulated Brillouin scattering (SBS). Compact high-power amplifier chains are built with low power all-fibre system and high-power bulk free-optics fibre amplifiers. When the total power is about 260 W, active phase-locking of two high-power amplifiers is demonstrated using the SPGD algorithm. In closed-loop, the power in the main lobe increases 1.68 times, the visibility is increased from 0 to 0.62, and the phase residual error is less than λ/10.     

122-W high-power single-frequency MOPA fiber laser in all-fiber format

We demonstrate a high-power single-frequency master oscillator power amplifier (MOPA) fiber laser.The central wavelength of the single-frequency fiber laser seed is 1 063.8 nm,with a linewidth narrower than 20 kHz and output power of 120 mW.By using two-stage amplification,a single-frequency fiber laser with an output power of 122 W is obtained,and the optical-optical conversion efficiency is 72%.No significant amplified spontaneous emission (ASE) or stimulated Brillouin scattering (SBS) is observed.The output power can be further increased by launching more pump power.     

国产大功率全光纤主振荡功率放大器

以国产掺Yb光纤为增益介质,利用国产泵浦源和光纤器件,构建了主振荡功率放大结构的全国产大功率全光纤激光器。在注入的最大泵浦功率为75 W时,获得了52.5 W,1 080 nm激光的稳定输出,光-光效率为70%。实验结果表明,提高泵浦功率可获得更高的输出功率。     

国产大功率全光纤主振荡功率放大器

 以国产掺Yb光纤为增益介质,利用国产泵浦源和光纤器件,构建了主振荡功率放大结构的全国产大功率全光纤激光器。在注入的最大泵浦功率为75 W时,获得了52.5 W,1 080 nm激光的稳定输出,光-光效率为70%。实验结果表明,提高泵浦功率可获得更高的输出功率。     

A 330-W single-frequency retrievable multi-tone monolithic fiber amplifier

A single-frequency retrievable phase modulated multi-tone fiber amplifier is presented in theory and demonstrated in experiment. A multi-tone seed laser generated by a sine wave phase modulated single-frequency laser is employed for stimulated Brillouin scattering suppression in an all-fiber amplifier. A demodulation signal which is π phase shifted with respect to the modulation signal is used to retrieve the single-frequency laser from the multi-tone laser. In experiment, we first optimize the all-fiber master-oscillator power-amplifier. With this amplifier, we demonstrate a single-frequency retrievable multi-tone laser with 330-W output when driven by the multi-tone seed, while the ultimate output power is only 130 W when driven by the single-frequency laser. Then, we carry out an experiment for retrieving the single-frequency laser from the amplified multi-tone laser. Results indicate that the single-frequency laser can be retrieved with a sideband suppression of more than 20 dB. Retrieving an even higher power single-frequency laser is possible if a high power demodulator is available.     

高功率全光纤激光器特性

介绍了采用国产光纤光栅研制的全光纤激光器,单端泵浦获得468 W的连续激光输出。从理论上分析了光纤光栅的反射率与波长的关系,计算了输出谱宽值,与实验测得的数据相符。全光纤激光器的光-光转换效率达到70%,且随着功率的增加,光纤光栅的中心波长有向长波方向漂移的趋势。在最高输出功率下180 s之内输出功率波动在0.04%以内。     

窄线宽纳秒脉冲光纤拉曼放大器的理论模型和数值分析

窄线宽纳秒脉冲光纤拉曼放大器在非线性频率变换、遥感探测和量子信息等领域有广泛的应用前景.综合考虑受激拉曼散射(stimulated Raman scattering,SRS)、受激布里渊散射(stimulated Brillouin scattering,SBS)、自相位调制(self-phase modulation)和交叉相位调制(cross-phase modulation)等非线性效应,建立了窄线宽纳秒脉冲光纤拉曼放大器的非线性动力学模型.仿真分析了放大器中脉冲激光的时频演化特性,对比研究了抽运脉冲宽度、光纤长度和信号光功率等因素对放大器性能的影响.研究发现,上述因素会影响放大器的SRS阈值、SBS阈值、输出激光线宽、激光转换效率等.例如,当脉冲宽度为800 ns时,SBS随着抽运功率的增加而发生,限制了激光功率的提升;减短抽运脉宽可以抑制SBS,但是输出激光的线宽易于展宽到数百MHz以上;增加光纤长度可以获得更低的SRS阈值和更高的转换效率,但是SBS效应和光谱展宽程度也随之增强.系统搭建中需要平衡各非线性效应,选择合适的系统参数.研究内容可以为窄线宽纳秒脉冲光纤拉曼放大器的设计搭建提供参考.     

国产纺锤形增益光纤主振荡功率放大器实现5 kW输出

设计了纤芯直径小—大—小变化的“纺锤形”增益光纤,利用该光纤可均衡模式不稳定和受激拉曼散射抑制的矛盾,提升光纤激光器的输出功率。基于自研的纺锤形增益光纤搭建了主振荡功率放大器（MOPA）,实现了5 kW的功率输出,放大器光光效率为66.6%,拉曼散射抑制比大于45 dB,M²因子约2.0。通过优化光纤的设计,可以提升激光器的光束质量和效率。

     

300 W侧面分布式抽运掺Yb全光纤放大器

采用角度磨抛的方式, 在纤芯/包层为20/400 μm双包层掺Yb光纤上制作了侧面抽运耦合器. 该耦合器对975 nm的半导体二极管抽运光的耦合效率最高可达97%, 对1080 nm信号光的泄漏比小于2%. 分析了侧面抽运耦合器的性能以及多个侧面抽运耦合器的级联分布对抽运耦合效率的影响; 同时, 在前向抽运和双向抽运方式下, 分析了级联耦合器的分布及信号光泄漏比对激光器整体效率的影响, 并进行了数值模拟. 采用自行研制的侧面抽运耦合器, 搭建了侧面耦合分布式抽运、掺Yb双包层全光纤主振荡功率放大器, 获得了波长为1080 nm、功率为303 W 的基模激光输出. 进一步增加抽运点个数, 提高抽运功率, 可获得更高的输出功率.     

A simple model of suppressing stimulated Brillouin scattering in optical fiber with frequency-modulated laser

A simple model is developed to study the mechanism of stimulated Brillouin scattering（SBS） suppression with frequency-modulated laser in optical fiber. By taking into account the laser frequency distribution along the fiber induced by frequency modulation, the average effective Brillouin gain is calculated to determine the SBS threshold. Experimental results show agreement with the numerical analysis. The application for SBS suppression in interferometric fiber sensing system is also discussed in this paper. The results show that the maximum input power can be increased effectively by frequency modulation method.     

受激布里渊散射相位共轭波的四波混频放大

本文介绍了一种产生相位共轭波的方法.此方法兼有四波混频方法和受激布里渊散射方法的优点,可得到转换效率大于1的高质量的相位共轭波.     

后向泵浦高功率掺镱光纤放大器的非弹性散射效应

在考虑受激布里渊散射和受激喇曼散射效应的基础上,数值求解了双包层掺镱光纤放大器的速率-传输方程,分析了后向泵浦高功率掺镱光纤放大器在不同信号光线宽、光纤长度和纤芯直径下的输出特性,研究了受激布里渊散射和受激喇曼散射的抑制条件。计算结果表明:在后向泵浦方式下,若掺镱光纤长度小于0.68 m,纤芯直径大于26 μm,信号光线宽大于0.04 nm,则放大过程中的受激布里渊散射和受激喇曼散射能同时得到有效抑制。     

后向泵浦高功率掺镱光纤放大器的非弹性散射效应

 在考虑受激布里渊散射和受激喇曼散射效应的基础上,数值求解了双包层掺镱光纤放大器的速率-传输方程,分析了后向泵浦高功率掺镱光纤放大器在不同信号光线宽、光纤长度和纤芯直径下的输出特性,研究了受激布里渊散射和受激喇曼散射的抑制条件。计算结果表明:在后向泵浦方式下,若掺镱光纤长度小于0.68 m,纤芯直径大于26 μm,信号光线宽大于0.04 nm,则放大过程中的受激布里渊散射和受激喇曼散射能同时得到有效抑制。     

高功率全光纤保偏主振荡功率放大型光纤激光器的实验研究

进行了全光纤保偏主振荡功率放大型光纤激光器的实验研究. 采用两级级联放大的方式, 利用纤芯为5 μupm 的小芯径双包层保偏光纤, 在最大抽运功率为88 W 时实现了67 W的1083 nm保偏激光输出, 纤芯内的激光功率密度约为3.4 W/μupm², 光-光转换效率为76%．分析结果表明, 进一步提高抽运功率有望获得更高功率的激光输出．     

High-energy femtosecond Yb-doped all-fiber monolithic chirped-pulse amplifier at repetition rate of 1 MHz

A high-energy femtosecond all ytterbium fiber amplifier based on a chirped-pulse amplification(CPA) technique at a repetition rate of 1 MHz seeded by a dispersion-management mode-locked picosecond broadband oscillator is studied.We find that the compressed pulse duration is dependent on the amplified energy,the pulse duration of 804 fs corresponds to the maximum amplified energy of 10.5 μJ,while the shortest pulse duration of 424 fs corresponds to the amplified energy of 6.75 μJ.The measured energy fluctuation is approximately 0.46% root mean square(RMS) over 2 h.The low-cost femtosecond fiber laser source with super-stability will be widely used in industrial micromachines,medical therapy,and scientific studies.     

2.14 kW级联泵浦光纤放大器

利用大模场掺镱光纤搭建了1018 nm高功率光纤激光器,获得了476 W的最高输出功率。利用6台高亮度1018 nm光纤激光器泵浦掺镱光纤,搭建了全光纤结构的级联泵浦光纤放大器,实现了2.14 kW的最高输出功率,输出功率随泵浦功率线性增长,整体斜率效率为86.9%,M2因子为1.9。