Bimetallic Rh-Co/ZrO<Subscript>2</Subscript> catalysts for ethanol steam reforming into hydrogen-containing gas

The properties of supported bimetallic Rh-Co/ZrO₂ catalysts in ethanol steam reforming into hydrogen-containing gas were studied. The particles of Rh-Co solid solutions on the catalyst surface were prepared by the thermal decomposition of the double complex salt [Co(NH₃)₆][Rh(NO₂)₆] and the solid solution Na₃[RhCo(NO₂)₆]. It was found that the bimetallic Rh-Co/ZrO₂ catalysts exhibited high activity in the reaction of ethanol steam reforming. The equilibrium composition of reaction products was attained at 500–700°C and a reaction mixture space velocity of 10000 h⁻¹.     

Influence of the conditions of manufacture of nanomeric zirconium dioxide,stabilized with yttrium oxide,on its catalytic properties in the oxidation of CO

The morphological and catalytic properties of samples of nanomeric zirconium dioxide, stabilized with yttrium oxide, manufactured via the effect of a UHF field during the process of drying precipitated zirconium hydroxide and calcination at temperatures from 300 to 1000 °C, were studied. It was shown that the highest activity in the oxidation of CO occurred with 40 nm particles of zirconium dioxide prepared at 1000 °C. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 43, No. 2, pp. 96–101, March–April, 2007.     

PlyC,an enzyme lysing group A,C, and E streptococci: Specific features of inactivation and the stabilization by intramolecular chemical crosslinking

The heat inactivation kinetics of PlyC lysin, an enzyme that lyses groups A, C, and E streptococcal cells, has been studied. It has been demonstrated that oligomeric PlyC is inactivated according to a dissociative mechanism in the temperature range of 37–41.5°C, pH 6–8, and enzyme concentrations of 0.3–160 μg/ml and at higher (42–50°C) or lower (35–22°C) temperatures, according to a monomolecular mechanism. A new efficient method for PlyC stabilization via intramolecular chemical crosslinking was proposed.     

Polyaniline dispersions 7. Dynamic light scattering study of particle formation

 When aniline is oxidized in the presence of colloidal silica, composite polyaniline–silica particles of submicrometer size are obtained. Dynamic light scattering was used to monitor the course of dispersion polymerization of aniline and the formation of particles. The increase of a hydrodynamic radius of particles was observed as polyaniline had been produced. Additional increase in particle size after polymerization has also been recorded. The rate of aniline polymerization was found to increase with increasing temperature in the range 0–50 °C. Well-defined particles are formed below 30 °C while above this temperature the colloidal stability of the resulting systems is limited. The activation energy of aniline polymerization was estimated. Received: 24 February 1997 Accepted: 7 May 1997     

A study on sol–gel synthesis and characterization of SiC nano powder

Nano sized β-SiC particles were synthesized from sol–gel process. Mono dispersed β-SiC nano particles with semi spherical morphology were obtained by employing APC as a dispersant agent and adjusting pH in the range of 2.5–4. Phenolic resin and TEOS were employed as precursors and heat treatment was conducted up to 1500 °C. Different techniques such as XRD, DTA, FTIR, PSA, SEM and TEM were used to characterize the formation of β-SiC. The (Si–O-C) bonds were formed by hydrolysis and condensation reactions in the gel while the nucleation of crystalline β-SiC was found to be initiated at 1400 °C. The primary particles in the sol were found to be (< 10 nm) while the size distribution in the final product was recorded in the range of 30–50 nm.     

Pt–Fe cathode catalysts to improve the oxygen reduction reaction and methanol tolerance in direct methanol fuel cells

High surface area carbon-supported Pt and bimetallic Pt–Fe catalysts are investigated for the oxygen electro-reduction reaction (ORR) in low-temperature direct methanol fuel cells (60 °C). The electrocatalysts are prepared using a combination of colloidal and incipient wetness methods allowing the synthesis of carbon-supported bimetallic nanoparticles with a particle size of about 2–3 nm. These materials are studied in terms of structure, morphology and composition using X-ray diffraction, X-ray fluorescence and transmission electron microscopy techniques. The electrocatalytic behaviour of these catalysts for ORR is investigated by employing the rotating disc technique. An enhancement of the ORR is observed with the bimetallic Pt–Fe catalyst in the oxygen-saturated electrolyte solution, with and without methanol. Dedicated to Prof. Dr. Teresa Iwasita on the occasion of her 65th birthday in recognition of her numerous contributions to interfacial electrochemistry.     

Selective dehydrogenation of isopropyl alcohol on low-percentage supported bimetallic rhenium-containing catalysts

The activity and selectivity of mono-and bimetallic sibunite-supported Re-, Cu-, Ni-, and Pd-containing catalysts in dehydrogenation of isopropyl alcohol to acetone (T=200–275 °C,v=1.1h⁻¹) were studied. The bimetallic Re, Cu-, Re, Ni-, and Re, Pd-catalysts containing 1 or 2% of the metal possess the higher activity and stability than monometallic catalysts. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 11, pp. 2381–2383, November, 1998.     

Controlling apatite microparticles formation by calcining electrospun sol–gel derived ultrafine silica fibers

Electrospun ultrafine silica fibers were calcined at 150–800 °C. The relation of calcination temperature to the ability to form biomimetic apatite in a simulated body fluid solution (SBF) was evaluated. The largest apatite particles, formed on non-calcined fibers after 1 week of soaking in SBF, were 10 μm in diameter, had a narrow size distribution (coefficient of variation 9%), and were similar to pearls on string. The particles size decreased with increasing calcination temperature below 250 °C and the particles formed on the fibers calcined at 250 °C were 4.5 μm in diameter. No particles were found on those calcined above 500 °C. By using a concentrated SBF at 1.5-times higher ionic concentrations than SBF, the size of apatite microparticles increased about 50%. The fibrous substrate covered with apatite particles was effective for osteoblastic differentiation of pre-osteoblastic cells.     

On the nature of decrease in the particles size of nanostructured nickel oxide obtained by the sol-gel method in the presence of surfactants

A processes of formation of nanostructured powders of nickel oxide by annealing in the temperature range of 200–700°C of the nickel hydroxide obtained by the sol-gel method at 80°C from solutions of nickel nitrate by precipitation with alkali in the presence of surfactant AF-12 (polyethylene oxide alkylphenyl ether) was investigated. The formation of nanostructured powders of nickel oxide in the presence of a surfactant reduces the size of nanoparticles to 20–25 nm, which is 1.5 times smaller than the particles obtained without a surfactant. The effective influence of surfactant on the particle size begins in the temperature range of its decomposition and evaporation equal 350–400°C.     

Zirconium titanate synthesis by diethanol amine based sol-gel route

ZrTiO₄ powder are synthesized by a modified sol-gel route via bimetallic diethanol amine complex of zirconium and titanium alkoxides. Samples are cured at 140°C and calcined between 500–800°C. Powders are characterized with XRD, TGA, DTA, SEM and TEM methods. The ZrTiO₄ powders are obtained at 650°C from the amorphous form. No identified peaks can be attibuted to other phases, namely, zirconia and titania are not observed.     

Effect of silicon dioxide on the formation of the phase composition and pore structure of titanium dioxide with the anatase structure

The formation of the structure of titanium dioxide modified with silicon dioxide, which was introduced as tetraethyl orthosilicate, was studied. It was found that the formation of the nanocrystalline structure of TiO₂ occurred upon the modification of titanium dioxide with silicon dioxide. This nanocrystalline structure of TiO₂ was formed by highly dispersed anatase particles of size 6–10 nm stabilized by silicon oxide layers, which were formed upon the decomposition of tetraethyl orthosilicate. An increase in the modifier concentration resulted in a deceleration of the growth of anatase particles and an increase in the temperature of the phase transition of anatase to rutile. It was found that the anatase phase in the samples containing 5–15 wt % SiO₂ was stable up to 1000°C. The stabilization of highly dispersed anatase particles facilitated the retention of the developed fine-pore structure of xerogels with a pore diameter of 4 nm up to 900°C.     

Some thermal characteristics of a mineral mixture of palygorskite,metahalloysite, magnesite and dolomite

An industrial raw material taken from Sivrihisar (Eskişehir, Turkey) region was heat-treated at different temperatures in the range of 100–1000°C for 2 h. The volumetric percentage of the particles having a diameter below 2 μm after staying in an aqueous suspension of the material was determined as 67% by the particle size distribution analysis. The mineralogical composition of the material was obtained as mass% of 32% palygorskite, 10% metahalloysite, 35% magnesite, 20% dolomite and 3% interparticle water by using the acid treatment, X-ray diffraction and thermal analysis (TG, DTA) data. The temperature ranges were determined for the endothermic dehydrations for the interparticle water as 25–140°C, for the zeolitic water as 140–320°C, and for the bound water as 320–480°C, in the palygorskite. The temperature range for the endothermic dehydroxylation and exothermic recrystalization of the palygorskite is 780–840°C. The temperature range for the endothermic dehydroxylation of the metahalloysite and calcinations of magnesite are coincided at 480–600°C. Dolomite calcined in the temperature range of 600–1000°C by two steps. The zig-zag changes in the specific surface area (S/m² g⁻¹) and specific micro and mesopore volume (V/cm³ g⁻¹) as the temperature increases were discussed according to the dehydrations in the palygorkskite, dehydroxylation of palygorskite and metahalloysite, and calcinations in magnesite and dolomite.     

Nano-sized polycrystalline bismuth silicon oxide powder by sol–gel technique

Bismuth silicon oxide (Bi₁₂SiO₂₀, BSO) nano crystalline powder was prepared by sol–gel technique using bismuth nitrate and tetraethyl orthosilicate as starting materials. The prepared samples were sintered at various temperatures (750 °C maximum) and characteristic sillenite single cubic phase with crystallite size ~38 nm (calculated from room temperature powder XRD measurements) was realized at 750 °C sintering temperature. SEM analysis showed that the powder contains the nano-sized particles with almost spherical morphology. The observed frequencies in room temperature FTIR spectrum could be assigned to Bi–O, Si–O and Bi–O–Si bonds. The FWHM (full width at half maximum) of the diffraction peaks decreased while the intensity of FTIR absorption lines increased with the increase in the sintering temperature indicating better bond formation and crystallization. The thermograph of the samples recorded in the temperature range 50–1,000 °C showed almost no weight loss after ~575 °C further confirmed the conclusion arrived at from XRD and FTIR analysis. The samples sintered at 750 °C showed about 50% absorbance in 400–600 nm region which was consistent with the pale yellow color of the sample. Broad blue emission centered ~478 nm was observed when excited by 350 nm radiation from a Xe-lamp. The intensity of this broad emission band increased while its FWHM decreased with the increase in sintering temperature. Self-trapped excitons could be responsible for this emission.     

Transformations of cyclohexane and benzene on the bimetallic Ru-Pt oxide catalysts

The bimetallic Ru-Pt/Al₂O₃ catalysts with an overall metal content of 1 wt. % and Pt: Ru weight ratios from 1: 3 to 3: 1 were studied. The catalytic activity for cyclohexane and benzene transformations, including hydrogenation, hydrogenolysis, and skeletal isomerization of the initial substrates and products of intermediate transformations, was studied at temperatures 180–350 °C and H₂ pressures from 1.0 to 5.0 MPa. The maximum yield of n-hexane from cyclohexane and benzene was obtained on the catalysts with a ruthenium content of 0.75–1.0%, being ∼29–30 wt.% at 40% selectivity. The selectivity to form n-hexane decreases with an increase in the cyclohexane conversion and is almost independent of the composition of the Ru-Pt system. On the catalysts under study, benzene is converted to the same products but at temperatures by 60 °C lower as compared to cyclohexane conversion. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 4, pp. 633–637, April, 2006.     

Uniform particles of manganese compounds obtained by forced hydrolysis of manganese(II) acetate

 Procedures for the preparation at low temperature (80 °C) of uniform colloids consisting of Mn₃O₄ nanoparticles (about 20 nm) or elongated α-MnOOH particles with length less than 2 μm and width 0.4 μm or less, based on the forced hydrolysis of aqueous manganese(II) acetate solutions in the absence (Mn₃O₄) or the presence (α-MnOOH) of HCl are described. These solids are only produced under a very restrictive range of reagent concentrations involving solutions of 0.2–0.4 mol dm⁻³ manganese(II) acetate for Mn₃O₄ and of 1.6–2 mol dm⁻³ Mn(II) and 0.2–0.3 mol dm⁻³ HCl for α-MnOOH. The role that the acetate anions play in the precipitation of these solids is analyzed. It seems that these anions promote the oxidation of Mn(II) to Mn(III), which readily hydrolyze causing precipitation. The evolution of the characteristics of the powders with temperature up to 900 °C is also reported. Thus, Mn₃O₄ particles transform to Mn₂O₃ upon calcination at 800 °C; this is accompained by a sintering process. The α-MnOOH sample also experiences several phase transformations on heating. First, it is oxidized at low temperatures (250–450 °C) giving MnO₂ (pyrolusite), which is further reduced to Mn₂O₃ at 800 °C. After this process the particles still retain their elongated shape. Received: 19 October 1999 Accepted: 24 November 1999     

The sol–gel transition of mullite spinning solution in relation to the formation of ceramic fibers

Continuous mullite ceramic fibers were fabricated by a sol–gel dry spinning technique. The sol was prepared from an aqueous solution of aluminum nitrate (AN), aluminum isopropoxide (AIP) and tetraethylorthosilicate (TEOS). The sol–gel transition was investigated by measuring the volume, the solid content, the viscosity and the rheological properties of the solution. Shear viscosity η of the mullite sol varied dynamically with concentrating time and temperature. Combine size analysis of sol particles and TEM analysis on this basis, the growth character of sol particles agglomeration and its structural evolution were discussed. By adjusting the temperature, the gelling degree could stabilize at a certain value and the sol–gel transition could be transferred to the spinning line. Continuous fibers were spun from such sols immediately before gelling in a laboratory dry spinning apparatus. The spinneret contained thirty circular holes, each having a diameter of 0.2 mm. The temperature inside the spinning channel was 100–120 °C, the winding speed was 100–300 m/min. Sintering of the precursor fibers at 1,100 °C yields crack-free mullite ceramic fibers.     

Liquid-phase hydrodechlorination of polychloroaromatic compounds in the presence of Pd-promoted nickel catalysts

Liquid phase hydrodechlorination of chlorobenzene, 1,2,4-trichlorobenzene, hexachlorobenzene, polychlorinated biphenyls in the ethanol-containing solution, on Me⁰/C (where Me⁰-Pd, Ni or bimetallic Ni−Pd; C-carbon material “Sibunit”) with H₂ have been studied at 20–70°C and P_{H 2}=1–50 atm. Pd and Pd-promoted Ni catalysts exhibit the highest activity. Kinetic studies show hydrodechlorination of these compounds to be a consecutive reaction, which under the conditions described may produce less chlorinated compounds.     

Preparation and characterization of nanocomposite ZnO–Ag thin film containing nano-sized Ag particles: influence of preheating,annealing temperature and silver content on characteristics

Nanocomposite ZnO–Ag thin film containing nano-sized Ag particles have been grown on glass substrate by spin-coating technique using zinc acetate dihydrate as starting precursor in 2-propanol as solvent and monoethanolamine as stabilizer. Silver nanoparticles were added in the ZnO sol using silver nitrate dissolved in ethanol-acetonitrile. Their structural, electrical, crystalline size and optical properties were investigated as a function of preheating, annealing temperature and silver content. The results indicated that the crystalline phase was increased with increase of annealing temperature up to 550 °C at optimum preheating temperature of 275 °C. Thermal gravimetric differential thermal analysis results indicated that the decomposition of pure ZnO and nanocomposite ZnO–Ag precursors occurred at 225 and 234 °C, respectively with formation of ZnO wurtzite crystals. The scanning electron microscopy and atomic force microscopy revealed that the surface structure (the porosity and grain size) of the ZnO–Ag thin film (the film thickness is about 379 nm) was changed compared to pure ZnO thin film. The result of transmission electron microscopy showed that Ag particles were about 5 nm and ZnO particles 58 nm with uniform silver nanoclusters. Optical absorption results indicated that optical absorption of ZnO–Ag thin films decreased with increase of annealing temperature. Nanocomposite ZnO–Ag thin films with [Ag] = 0.068 M and [Ag] = 0.110 M showed an intense absorption band, whose maximum signals appear at 430 nm which is not present in pure ZnO thin films. The result of X-ray photoelectron spectroscopy revealed that the binding energy of Ag 3d_5/2 for ZnO–Ag shifts remarkably to the lower binding energy compared to the pure metallic Ag due to the interaction between Ag and ZnO.     

Fabrications of Nb-doped TiO<Subscript>2</Subscript> (TNO) transparent conductive oxide polycrystalline films on glass substrates by sol–gel method

Anatase Ti_0.94Nb_0.06O₂ (TNO) films were fabricated on glass substrates by sol–gel method using a dip-coating technique. The annealing treatment was separated into two steps, first in air at 350–550 °C for 1 h and then in vacuum of 4.0 × 10⁻⁴ Pa at 550 °C for 1 h. The influence of vacuum annealing treatment to the electrical and optical properties was discussed. Especially, the role of air annealing treatment from 350 to 550 °C on the crystallization and the structure of the films was analyzed. It is proved that the films annealed at 550 °C in air and then 550 °C in vacuum exhibited the minimum resistivity of 19.3 Ω·cm and the average optical transmittance of about 75% in the visible range, indicating that the sol–gel method is a feasible and promising method to fabricate TNO films.     

Thermal degradation of poly(lactic acid) measured by thermogravimetry coupled to Fourier transform infrared spectroscopy

Thermogravimetric (TG), differential thermal analysis (DTA) and thermal degradation kinetics, FTIR and X-ray diffraction (XRD) analysis of synthesized glycine–montmorillonite (Gly–MMT) and montmorillonite bound dipeptide (Gly–Gly–MMT) along with pure Na–MMT samples have been performed. TG analysis at the temperature range 25–250 °C showed a mass loss for pure Na–MMT, Gly–MMT and Gly–Gly–MMT of about 8.0%, 4.0% and 2.0%, respectively. DTA curves show the endothermic reaction at 136, 211 and 678 °C in pure Na–MMT whereas Gly–MMT shows the exothermic reaction at 322 and 404 °C and that of Gly–Gly–MMT at 371 °C. The activation energies of the first order thermal degradation reaction were found to be 1.64 and 9.78 kJ mol⁻¹ for Gly–MMT and Gly–Gly–MMT, respectively. FTIR analyses indicate that the intercalated compounds decomposed at the temperature more than 250 °C in Gly–MMT and at 250 °C in Gly–Gly–MMT.