氧化型谷胱甘肽-二茂铁的合成及其电化学性质研究

采用液相合成法,以二茂铁甲酸、氧化型谷胱甘肽(GSSG)为原料,苯并三唑-1-四甲基六氟磷酸酯(HBTU)及1-羟基苯并三唑(HOBt)为缩合剂,合成了具有电活性的目标化合物氧化型谷胱甘肽-二茂铁(Fc-GSSG-Fc),其收率为46%,并对其进行了表征。目标化合物Fc-GSSG-Fc的循环伏安扫描结果表明,在0～0.8V范围内出现了一对可逆的氧化还原峰,氧化峰和还原峰电位分别为0.459和0.391V;峰电位之差ΔEp为68mV,峰电流密度之比Ipa/Ipc为1.02,扩散系数D0=1.175×10-8cm2·s-1。利用电化学方法研究了Fc-GSSG-Fc与Zn(Ⅱ)之间的配位特性。实验结果表明,Fc-GSSG-Fc与Zn(Ⅱ)形成了1:1的配合物。     

硫代硫酸盐在铂电极上的电化学氧化行为

用循环伏安法测定了硫代硫酸盐在铂电极上的电化学氧化行为, 结果表明, 其电化学氧化行为与体系的pH和扫描速度密切相关. 当pH为5~6时, 硫代硫酸盐的循环伏安曲线出现三个氧化峰, 峰电位分别在0.05 V、0.58 V和1.02 V附近, 随pH值升高和扫描速度的降低, 0.05 V附近的氧化峰逐渐变得明显, 同时各氧化峰的峰电位与扫描速度的对数, 峰电流与扫描速度的平方根均成很好的线性关系；当pH为8~9时, 硫代硫酸盐的循环伏安曲线出现三个明显的氧化峰, 峰电位分别在0.05 V、0.91 V和1.22 V附近. 随扫描速度降低, 循环伏安曲线出现交叉, 体系呈现明显的电化学振荡行为；但当pH=10时, 1.22 V附近的氧化峰消失. 硫代硫酸盐的电化学氧化行为非常复杂, 电化学氧化机制随体系pH的变化而变化.     

多壁碳纳米管固载亚甲基蓝复合膜修饰玻碳电极测定己烯雌酚

提出了多壁碳纳米管-聚亚甲基蓝(MWNT/PMB)复合膜修饰玻碳电极检测己烯雌酚(DES)的方法,考察了缓冲液、pH、扫描速度等实验参数对测定的影响。在0.2 mol/L的磷酸缓冲液(pH7.0)中,DES在复合膜电极上出现了一个明显的氧化峰,峰电位在0.197 V处。与裸电极相比较,修饰后的电极能显著提高DES的氧化峰电流并降低其氧化电位,表明MWNT/PMB复合膜对DES有电催化作用。峰电流与己烯雌酚浓度在3.73×10-11~3.73×10-8mol/L范围内呈线性关系,检出限为2×10-11mol/L;用此法对己烯雌酚药片的含量进行了测定,测定结果与标示相符。     

聚藏红T修饰电极的制备及对多巴胺的电催化性能

用循环伏安法在石墨电极和ITO导电玻璃上制备了藏红T聚合物薄膜修饰电极,研究了电聚合过程及循环伏安性质.聚藏红T膜修饰石墨电极在pH 6.81的PBS中循环扫描,有两对氧化还原峰,峰电位分别为Ep,a(P1)=-0.5 V,Ep,c(P1)=-0.575 V,Ep,a(P2)=-0.36 V,Ep,c(P2)=-0.425 V,而且聚合物较稳定.测定了聚藏红T膜的可见光谱性质.实验表明,聚藏红T膜修饰电极对多巴胺有明显的催化作用.     

NanoTiO2-CNT复合膜电极在DMF溶液中对糠醛的异相电催化还原

通过在乙醇中电化学溶解Ti金属阳极合成前驱体Ti(OEt)4和溶胶-凝胶法在Ti表面修饰一层纳米TiO2-碳纳米管(nanoTiO2-CNT)复合膜, 采用循环伏安和电解合成法研究了nanoTiO2-CNT复合膜电极在N, N-二甲基甲酰胺(DMF)中的氧化还原行为以及对糠醛(furfural)还原的电催化活性. 结果发现, nanoTiO2-CNT电极在阴极扫描时有两对氧化还原峰, 可逆半波电位E r1/2 分别为－1.27 V和－2.44 V(vs SCE, 扫描速度100 mV•s-1), 分别对应于TiO2/Ti2O3氧化还原电对的可逆电极过程和TiO2/Ti(OH)3电对的准可逆电极过程；在DMF电解液中nanoTiO2-CNT复合膜中的Ti(IV)/Ti(III)氧化还原电对作为媒质间接电还原糠醛为糠醇, 反应机理为电化学偶联随后化学催化反应(EC′)机理.     

聚天青Ⅰ玻碳修饰电极对血红蛋白催化还原

报道了天青Ⅰ在玻碳电极上的电化学聚合 ,研究了聚天青I修饰电极的电化学性质。该电极在 0 .2 5mol L硫酸底液中于 +0 .8～ - 0 .8V电位范围内有 3个峰 ,峰 1,3是一对氧化还原峰。Ep1 =+0 12 3V ,Ep2 =- 0 .432V ,Ep3 =- 0 .12 5V(vs.Ag AgCl) ,并在 0 .2 5mol L硫酸溶液中研究了聚天青修饰电极对血红蛋白的催化还原 ,血红蛋白浓度在 0 .5～ 6 0mg L范围内与峰电流呈线性关系 ,其回归方程Ip=1 0 0 2× 10 - 5+0 .15 6× 10 - 5C ,r=0 .9995。文中对电催化过程进行了探讨     

延胡索酸泰妙菌素在碳糊电极上的电化学性质及电分析方法

运用循环伏安法(CV)、计时电流法(CA)和计时电量法(CC)研究了延胡索酸泰妙菌素(Tiamulin fumarate,TF)在碳糊电极(Carbon Paste Electrode,CPE)上的电化学及其电化学动力学性质。结果表明,TF在CPE上的电化学过程是一不可逆的氧化过程,氧化峰电位Ep为0.772 V。在扫描速度10～1 000 mV.s-1范围内,其氧化峰电流Ip与扫描速度v呈良好的线性关系,表明TF在CPE上的伏安行为是一受吸附控制的过程。方波伏安(SWV)法结果表明TF氧化峰电流与其浓度在5.0×10-7～1.0×10-5mol.L-1及1.0×10-5～1.0×10-4mol.L-1范围内均呈良好的线性关系,相关系数r分别为0.9980及0.9966,检出限(S/N=3)为5.8×10-8mol.L-1,相对标准偏差(RSD)为0.8%～2.8%,加样回收率为97.6%～102.0%。据此建立了TF含量的电化学测定方法。该方法简便快捷,测定结果令人满意。     

亚铁氰化钾电催化氧化L-半胱氨酸的电化学行为研究

研究了在0.10 mol/L Na2SO4溶液中K4Fe(CN)6在玻碳电极(GCE)上电催化氧化L-半胱氨酸(L-Cys)的电化学行为。在-0.2~0.6 V的电位窗口内,L-Cys在GCE上的直接电化学氧化过程迟缓,不易直接发生氧化反应。在K4Fe(CN)6作用下,在0.23 V处出现一个不可逆的氧化峰,且氧化峰电流明显增大。研究结果表明,K4Fe(CN)6对L-Cys的氧化具有良好的电催化作用。电催化氧化峰电流Ipa随扫描速度的增大而增大,且与扫描速率平方根(v1/2)呈线性关系,表明该电催化氧化反应是受扩散控制的电化学过程。催化氧化峰电流与L-Cys浓度在4×10-5~2×10-3mol/L范围内呈良好的线性关系(R=0.9966)。该催化反应过程中电子转移系数α=0.5568,运用计时电流法(CA)得到该电催化氧化的速率常数k为(7.19±0.05)×102(mol/L)-1.s-1。     

CuFe_2O_4纳米粒子-石墨烯修饰电极测定对硝基苯酚

在玻碳电极表面修饰一层纳米CuFe_2O_4-石墨烯复合膜,研究了对硝基苯酚在复合膜上的电化学行为。该复合膜对对硝基苯酚具有明显的电催化作用,测得一对不可逆氧化还原峰电位分别为0.063 V和-0.020 V。考察了支持电解质种类、酸度、修饰层厚度和扫描速度等对对硝基苯酚伏安响应的影响。在优化实验条件下,氧化峰电流与还原峰电流在浓度为3.0×10~(-5)~1.0×10~(-4)mol/L的范围内呈现良好的线性关系,检出限为8.0×10~(-7)mol/L。方法应用于模拟水样中对硝基苯酚的测定,回收率为99.2%~101.1%。     

司帕沙星的单扫示波极谱法

在 0 .2 mol·L- 1KH2 PO4 - K2 HPO4 ( p H6.80 )底液中 ,用单扫示波极谱法可以得到一个灵敏的司帕沙星导数还原峰 ,其峰电位 Ep=- 1 .43V( vs.SCE) ,导数峰电流与司帕沙星浓度在 0 .1～ 8.0μmol· L- 1范围内呈线性关系 ,检出限为 0 .0 5μmol· L- 1。该法应用于模拟尿样和胶囊中司帕沙星质量含量的测定 ,结果满意。对司帕沙星在汞电极上的电化学行为进行了探讨     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Investigation of Kinetics of Solid-Phase Synthesis of Lithium Orthosilicate

The kinetics of the interaction between lithium carbonate and silica with various degrees of dispersion was investigated by TG and DTA methods. It was found that the utilization of pyrogenic silica with a specific surface area of about 300 m²g^-1 instead of aerosil with one of 175 m²g^-1 leads to an increase of the reaction rate between lithium carbonate and silica, which depends on the formation and growth of lithium orthosilicate crystals in the first stage, and is conditioned by the diffusion of lithium and oxygen ions through the lithium orthosilicate layer formed at temperatures above 800 K. This supposition is supported by the kinetic analysis results obtained with the use of the different models. The optimal regime of heating is recommended. This revised version was published online in July 2006 with corrections to the Cover Date.     

小环化合物中饱和碳质子化学位移的计算

小环化合物由于其张力、构型、构象和各向异性效应等原因,环碳上质子化学位移缺乏规律性,难以预测,对此作者曾提出一种近似算法。本文根据303种小环化合物中饱和碳质子的化学位移实验数据,将适于计算这类质子化学位移的公式表述为:     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.