Coupling of a Reagentless Electrochemical DNA Biosensor with Conducting Polymer Film and Nanocomposite as Matrices for the Detection of the HIV DNA Sequences

Abstract

This paper describes a reagentless electrochemical DNA biosensor applied to the detection of human immunodeficiency virus (HIV) sequences based on electrochemical impedance spectroscopy (EIS). The novel DNA biosensor has been elaborated by means of an opposite‐charged adsorption Au‐Ag nanocomposite to a conductive polymer polypyrrole (PPy) modified platinum electrode (Pt) and self‐assembly the mercapto oligonucleotide probes onto the surface of modified electrode via the nanocomposite. The duplex formation was detected by measuring the electrochemical impedance signal of nucleic acids in phosphate buffer solution (PBS). Such response is based on the concomitant conductivity changes of the PPy film and nanocomposite. The reagentless scheme has been characterised using 21‐mer synthetic oligonucleotides as models: parameters affecting the hybridization assay were explored and optimized. The detection limit is 5.0×10^?10 M of target oligonucleotides at 3σ. The potential for development of reagentless DNA hybridization analysis in the clinical diagnosis is being pursued.     

Simple PVC–PPy electrode for pH measurement and titrations

Cobaltabis(dicarbollide) [3,3'-Co(1,2-C2B9H11)](-)-doped polypyrrole (PPy) films have been prepared galvanostatically on glassy carbon electrodes in acetonitrile solution. The potential response behavior of the film of this new material has been investigated in some common pH buffers and in acid-base titrations. The potentiometric characteristics of the resulting films are indicative of a quasi-Nernstian response (approximately 50 mV/pH unit), a linearity range from pH 12 to 3 and correlation coefficients (r2) of approximately 0.98. The electrode is suitable for pH measurements and for monoprotic titrations of strong alkalis with strong acids, and weak bases with strong acids, but the long response time hinders the use of this electrode for multiprotic titrations. The time response has been dramatically improved by reducing the film thickness by using the template effect of a non-conducting polymer (PVC) cast over the graphite surface before PPy deposition. PPy polymerization occurs in the free channels of PVC leading to the formation of PPy wires. The morphological change of PPy does not affect the slope or linearity range. The response of the PVC-PPy electrochemical sensor is rapid and the sensor is easy to prepare, at low cost, and its performance is comparable with that of commercial glass electrodes.     

Carbon-nanotube/copper composite electrodes for capillary electrophoresis microchip detection of carbohydrates

The preparation of carbon nanotube (CNT)/copper composite electrodes, based on co-mixing CNT and Cu powders within mineral oil, is described. The new composite electrode is used for improved amperometric detection of carbohydrates following their capillary electrophoresis (CE) microchip separations. The CNT/Cu composite electrode detector displays enhanced sensitivity compared to detectors based on copper or CNT alone. The marked catalytic action of the CNT/Cu composite material permits effective low potential (+0.5 V vs. Ag/AgCl) amperometric detection, and is coupled to the renewability, bulk modification and versatility advantages of composite electrodes. The CNT/Cu composite surface also leads to a greater resistance to surface fouling compared to that observed at the copper electrode. Factors affecting the electrocatalytic activity and the CE microchip detection are examined and optimized. The CNT/Cu composite electrode is also shown to be useful for the detection of amino acids as indicated from preliminary results. While the present work has focused on the enhanced CE microchip detection of carbohydrates and amino acids, the CNT/metal-composite electrode route should benefit the detection of other important groups of analytes.     

Nickel-titanium alloy electrodes for stable amperometric detection of underivatized amino acids in anion-exchange chromatography

Nickel-titanium (Ni-Ti) alloy electrode was used as an electrochemical detector for the analysis of underivatized amino acids in flow systems. In strong alkaline solution, an oxide film on the Ni-Ti alloy electrode surface exhibited a high catalytic activity toward the oxidation of amino acids. Cyclic voltammetry experiments confirmed that electrogenerated Ni(III)O(OH) functioned as the key redox mediator associated with the oxidation of the amine group in amino acids. The electrochemical behavior of the Ni-Ti electrode in alkaline medium was very similar to the Ni electrode. However, the oxide film was found to be much stable on Ni-Ti than on Ni. Consequently, the Ni-Ti alloy electrode exhibited an excellent stability for constant-potential amperometric detection of amino acids in flow systems. For example, the relative standard deviation (R.S.D.) for the repetitive 100 injections of 50 muM (1.2 nmol) glycine over 10 h was less than 1%. It was postulated that the presence of Ti in the alloy stabilizes the microstructure of oxide layer on the electrode surface. The sensitivities of amino acids at the electrode were different, depending on their chemical structures. The detection limits obtained in a range from 0.9 pmol for arginine to 90.2 pmol for leucine and isoleucine. The Ni-Ti alloy electrodes have been demonstrated to be very suitable for the amperometric detection of underivatized amino acids in anion-exchange chromatography.     

Selective determination of tryptophan by using a carbon paste electrode modified with an overoxidized polypyrrole film.

We report on the selective determination of tryptophan, using a carbon paste electrode coated with an overoxidized polypyrrole film. Out of 21 protein amino acids, only tryptophan and tyrosine exhibited an oxidative voltammetric response with this electrode. Tryptophan, which was preferentially concentrated to the electrode under an open circuit condition, was determined by the stripping voltammetric technique with a linear response range of 10-100 microM. For the determination of 10 microM tryptophan, interference from a 15-fold excess of tyrosine gave an positive error of 6%, while the other amino acids did not exhibit any detectable interference.     

Electrochemical preparation of effective and low cost catalyst for electrooxidation of ethanol

A nanocatalyst coating was prepared at surface of a glassy carbon electrode by electropolymerization of pyrrole by cycling the electrode potential between ?0.8 and 0.8 V (vs. Ag/AgCl). Then, polypyrrole film was potentiostatically coated with platinum nanoparticles at constant potential of ?0.2 V (vs. Ag/AgCl). The resulting electrode was denoted as GCE/PPy/Pt. This modified electrode was characterized by IR, SEM, TEM and EDX. The electrocatalytic oxidation of ethanol at the GCE/PPy/Pt has been investigated using cyclic voltammetric and chronoamperometric methods. The effects of various parameters on electrocatalytic oxidation of the ethanol, such as the thickness of PPy film, the amount of platinum nanoparticles, ethanol concentration, potential scan rate and working potential limit in anodic direction, were investigated. The kinetic of the ethanol oxidation is discussed on the GCE/PPy/Pt. The stability and reproducibility of this modified electrode were also studied.     

Minimizing analyte electrolysis in electrospray ionization mass spectrometry using a redox buffer coated emitter electrode

An emitter electrode with an electroactive poly(pyrrole) (PPy) polymer film coating was constructed for use in electrospray ionization mass spectrometry (ESI‐MS). The PPy film acted as a surface‐attached redox buffer limiting the interfacial potential of the emitter electrode. While extensive oxidation of selected analytes (reserpine and amodiaquine) was observed in positive ion mode ESI using a bare metal (gold) emitter electrode, the oxidation was suppressed for these same analytes when using the PPy‐coated electrode. A semi‐quantitative relationship between the rate of oxidation observed and the interfacial potential of the emitter electrode was shown. The redox buffer capacity, and therefore the lifetime of the redox buffering effect, correlated with the oxidation potential of the analyte and with the magnitude of the film charge capacity. Online reduction of the PPy polymer layer using negative ion mode ESI between analyte injections was shown to successfully restore the redox buffering capacity of the polymer film to its initial state. Published in 2010 by John Wiley & Sons, Ltd.     

蒽醌/聚吡咯复合膜修饰电极的电化学行为和电催化活性

在水溶液中制备了掺杂蒽醌磺酸盐(AQS)的聚吡咯(PPy)/玻碳复合膜修饰电极,采用循环伏安法和旋转圆盘电极技术研究了该修饰电极在不同pH值溶液中的电化学行为以及在pH=5.5的磷酸盐缓冲溶液中对氧还原反应的电催化性能和动力学.结果表明,与裸玻碳电极相比,PPy膜的存在不仅降低了AQS的反应电位和峰电位差,而且增大了其氧化还原反应的峰电流,H2AQ/HAQ-氧化还原对的电离常数为9.5.AQS/PPy膜修饰电极上氧的还原主要是两电子还原为H2O2的不可逆过程,H2AQ对氧还原反应起主要催化作用,还原过程符合异相氧化还原催化机理.该修饰电极具有良好的电化学重现性.     

Electrocatalytic Application of an Overoxidized Dopamine Film Prepared on a Gold Electrode Surface to Selective Epinephrine Sensing

A dopamine polymer film was prepared ex situ on a bare gold template from a 10 mM dopamine solution in phosphate buffer, pH 7 followed by an overoxidation in 500 mM NaOH. The modified electrode was used for quantitative determination of epinephrine. A linear relationship between epinephrine concentration and current response was obtained in the range between 2 μM and 800 μM with the detection limit of 0.3 μM. The results have shown that using the overoxidized dopamine film it is possible to perform electrochemical analysis of epinephrine without interference of ascorbic and uric acids.     

Indirect amperometric detection of underivatized amino acids in microcolumn liquid chromatography with carbon film based ring-disk electrodes

An indirect amperometric detection of underivatized amino acids has been developed using a carbon film based ring-disk electrode (CFBRDE) in microcolumn liquid chromatography (LC). Bromide present in the mobile phase could be efficiently oxidized to bromine at the upstream (disk) electrode, and was subsequently detected at the downstream (ring) electrode. Most of the underivatized amino acids that are electroinactive under conventional amperometric conditions react rapidly with the electrogenerated bromine, the concentration of amino acids can therefore be indirectly determined by continuously monitoring the reduction current of bromine. The signal monitored at the downstream electrode was largely dependent on the bromide concentration in the mobile phase. Under optimized conditions, the response linearly increased with the concentration for most of the amino acids over a concentration range of 1-100 microM, with a correlation coefficient of 0.990-0.993. The detection limits for most of the amino acids were below 1 microM (0.2 pmol). It was demonstrated that detection with a ring-disk electrode offers the advantages of achieving a much higher collection efficiency caused by a decrease in flow rate in the microcolumn LC.     

Separation of tryptophan enantiomers with molecularly imprinted polypyrrole electrode column

<正>In this study,we have fabricated molecularly imprinted polypyrrole(PPy) packed electrode columns and investigated their effects on separation of tryptophan(Trp) enantiomers by using potential control.The results indicate that the imprinted PPy electrode columns could efficiently enhance the L-Trp uptake and separate Trp enantiomers effectively,implying the great potential for the enantioselective recognition of other amino acids enantiomers.     

介孔碳/聚苯胺修饰电极的制备及其对Cu~(2+)的响应研究(英文)

制备了一个新的电极-聚苯胺掺杂介孔碳修饰电极(PANI-MC),并且研究了电极的电化学性质。在介孔分子筛SBA-15的孔道中沉积蔗糖,然后在氮气的保护下,1200℃热裂解,生成孔道规则排列的介孔碳(MC);XRD、N2吸附-脱附、TEM等方法表征了介孔碳的结构,用SEM表征了PANI-MC修饰电极的形貌。结果表明:复合电极膜与修饰前的聚苯胺膜形貌不同,与介孔碳形貌相似,介孔碳纳米微粒的大小清洗可辨,长度大约为20~40μm。复合电极循环伏安结果显示:峰电位向负电位方向移动,这可能是因为介孔碳的孔道结构阻碍了离子的转移。同时,还研究了复合电极对Cu2+的相应,表明:电极对低浓度的Cu2+有很好的线性相应,可以作为Cu2+的感应器。     

Amperometric detection of amino acids with a passivated copper electrode

The amperometric behaviour of a copper electrode towards amino acids is studied by means of a rotating disc electrode. A theoretical model describing the anodic background current in a buffer solution and the increase of the current caused by amino acids is checked experimentally. The influences of the amino acid concentration, the rotation speed of the electrode and the composition of the buffer solution are studied. It is proved that chemical dissolution of a passivating film on the electrode surface, which is enhanced by the complexation reaction between the amino acid and copper(II) ions, is the principle of the phenomena observed. The applicability to flow systems is demonstrated.     

聚拉莫三嗪修饰玻碳电极测定痕量铜(Ⅱ)的研究

在稀H2SO4介质中,采用循环伏安法制备了聚拉莫三嗪膜修饰玻碳电极(PLTG/GCE),将制得的膜修饰电极(PLTG/GCE)在一定电位下选择性预富集Cu(Ⅱ),并用差分脉冲溶出伏安法测定.结果表明,该膜修饰电极对Cu(Ⅱ)的富集作用明显强于裸玻碳电极.对电聚合条件、富集和溶出介质、富集时间及富集电位等实验参数进行了考察,在优化实验条件下,Cu(Ⅱ)的浓度在4.0×10-9～1.3×10-7mol· L-1范围内与溶出峰电流呈线性关系,相关系数为0.9999,检出限为1.5×10-9 mol·L-1.该修饰电极具有较高的灵敏度和选择性,用于实际水样的分析,平均回收率为98.7％.     

Label-free and sensitive impedimetric nanosensor for the detection of cocaine based on a supramolecular complexation with β-cyclodextrin,immobilized on a nanostructured polymer film

Cocaine, a powerful addictive stimulant drug, has a variety of adverse effects on the body, thus its sensitive detection is very important. Here, we report on a simple, label-free, and sensitive impedimetric sensor for determination of cocaine based on its affinity to form an inclusion complex with β-cyclodextrin (β-CD). First, we prepared nanostructured poly N-acetylaniline film via electropolymerization of its monomer on a glassy carbon electrode (PNAANI/GC), subsequently overoxidized it, and conjugated β-CD to the polymer backbone. The designed and synthesized nanostructured PNAANI film serves a dual function in the sensor: on one hand, it maintains a high effective surface area on a geometrically small electrode that significantly enhances the number of β-CD molecules immobilized on the electrode; on the other hand, it provides an upright-oriented β-CD conjugation to the polymer backbone, thus all the β-CD receptors are actively involved in responding to the target. Sensitivity of the sensor was further enhanced by preconcentration of cocaine on the modified electrode surface. We attributed the changes in the interfacial charge transfer resistance (R _ct) of the electrode to cocaine concentration. Under optimized condition (pH 7.4, 5-min accumulation at an open circuit voltage), the sensor responded to cocaine concentration in the range of 100 nM–1.0 mM with a detection limit of 50 nM. Selectivity of the sensor for cocaine relative to some potential inferring compounds was also investigated, and the results were promising. The proposed approach exhibited an extended dynamic range, low detection limit, good sensitivity, and a desirable selectivity, which provides an efficient application prospect for on-field cocaine sensing.     

A Novel Bioelectrochemical Sensor Based on Immobilized Urease on the Surface of Nickel Oxide Nanoparticle and Polypyrrole Composite Modified Pt Electrode

Nickel oxide nanoparticle (NiO?NP) and polypyrrole (PPy) composite were deposited on a Pt electrode for fabrication of a urea biosensor. To develop the sensor, a thin film of PPy?NiO composite was deposited on a Pt substrate that serves as a matrix for the immobilization of enzyme. Urease was immobilized on the surface of Pt/PPy?NiO by a physical adsorption. The response of the fabricated electrode (Pt/PPy?NiO/Urs) towards urea was analyzed by chronoamperometry and cyclic voltammetry (CV) techniques. Electrochemical response of the bio‐electrode was significantly enhanced. This is due to electron transfer between Ni²⁺ and Ni³⁺ as the electro‐catalytic group and the reaction between polypyrrole and the urease‐liberated ammonium. The fabricated electrode showed reliable and demonstrated perfectly linear response (0.7–26.7 mM of urea concentration, R²= 0.993), with high sensitivity (0.153 mA mM^?1 cm^?2), low detection of limit (1.6 μM), long stability (10 weeks), and low response time (～5 s). The developed biosensor was highly selective and obtained data were repeatable and reproduced using PPy‐NiO composite loaded with immobilized urease as urea biosensors.     

The Direct Electrochemical Detection of Amino Acids at a Platinum Electrode in an Alkaline Chromatographic Effluent

Abstract

It is the general experience that most organic compounds including amino acids do not produce reversible or even quasi-reversible anodic waves at a Pt electrode under conditions of conventional cyclic voltammetry. Furthermore, amperometric detection of these compounds at a constant electrode potential is not successful because of the accumulation of adsorbed reaction products and/or an oxide film at the electrode surface. However, it is observed that a Pt electrode surface is cleaned quite effectively of adsorbed organic molecles and radicals simultanaeously with the anodic formation of the oxide layer. This oxidation of adsorbed organic species is concluded to be electrocatalyzed by PtOH formed as the first step in the production of the oxide layer (PtO). A pulsed-potential waveform applied at a frequency of ca. 1 Hz is demonstrated to provide direct amperometric detection of adsorbed amino acids at a Pt electrode. Satisfactory analytical precision (i.e., < 3% rel. std. dev.) results because the waveform reproducibly generates the catalytically active surface state at the Pt electrode. Both primary and secondary amino acids are determined with satisfactory detection limits: e.g., ca. 13 ng for glycine, 7 ng for phenylamine and 23 ng for hydroxyproline in 50-μL samples. Analytical response is concluded to depend on the adsorption isotherm of the amino acid being detected. Hence, the calibration plot of I/I_peak vs. 1/C^D is linear for low surface coverages. Results are shown for amperometric detection of a synthetic mixture of amino acids by anion-exchange chromatography using NaOH as the eluent and supporting electrolyte.     

Detection of V-type nerve agent degradation products at electrodes modified by PPy/PQQ using CaCl2 as supporting electrolyte

Electrochemical detection without derivatization was used to detect thiol-containing degradation products of V-type nerve agents. Electropolymerization of pyrrole was used for entrapment of the biocatalyst PQQ to produce a sensor. Various parameters which affect the detection processes such as the type of the supporting electrolyte used during electrodeposition and the thickness of the polypyrrole film were examined and optimized. Electocatalytic oxidation of thiols by the PPy/PQQ electrode was strongly affected by the presence of Ca²⁺ cations during electrodeposition of the PPy/PQQ. Cyclic voltammetry, linear sweep voltammetry and amperometry have been used for electrode characterization. Amperometric detection of the V-type nerve agent thiol degradation products 2-(dimethylamino)ethanethiol (DMAET) and 2-(diethylamino)ethanethiol (DEAET) was performed at 0.38 V. Linear calibration plots were observed for these compounds. The detection limits of 4.5 and 3 μM were obtained for DMAET and DEAET respectively, with sensitivities of 1.18 and 1.37 nA μM⁻¹ cm⁻².     

Highly enantioselective discrimination of amino acids using copper deposition on a gold electrode modified with homocysteine monolayer

An extremely enhanced enantioselectivity was achieved for the detection of enantiomers of alanine (Ala), leucine (Leu), and 3,4-dihydroxyphenylalanine (DOPA) based on the voltammograms for the deposition of Cu from Cu complexes of the amino acids at an Au electrode modified with a self-assembled monolayer (SAM) of l-homocysteine (Hcy). The enantioselective current density peak for the Cu deposition was found to change with increasing number of potential cycles after the addition of Cu(II), and the highest enantioselectivity was observed immediately after the addition of Cu(II). Besides, enantioselectivity was not observed with proline, whose five-membered ring contains the nitrogen atom of a secondary amino group, while some amino acids with a primary amine group such as Ala, Leu, and DOPA exhibited enantioselectivity. These results suggest that the chiral ligand exchange reaction at the l-Hcy SAM-modified Au electrode, namely, the enantioselective formation of diastereomeric complexes of Cu(II) with target enantiomers and l-Hcy self-assembled on the Au electrode, plays an important role in the chiral discrimination based on the Cu deposition.     

Enantioselective uptake of amino acid with overoxidized polypyrrole colloid templated with L-lactate

An overoxidized polypyrrole colloid, which can recognise enantiomers of amino acids has been prepared by a newly developed molecular imprinting technique. A polypyrrole colloid, which had been polymerised from a mixture of pyrrole (monomer), polyvinylpyrrolidone (steric stabiliser), peroxodisulfate (oxidant) and L-lactate (dopant), was overoxidized to create a dopant-complementary cavity. The enantioselectivity of the overoxidized colloid was evaluated by comparing the uptake of L-alanine and L-cysteine with that of the respective D-enantiomers. The L/D uptake ratios for these amino acids were about 2, while phenylalanine showed suppressed uptake for both the enantiomers. The absence of phenylalanine uptake can be explained in terms of the molecular size, which is too large to be accommodated by the cavity created by L-lactate. In contrast, a colloid templated with L-phenyllactate took up L-phenylalanine with a higher enantioselectivity of about 7. A colloid templated with L-lactate was applied to surface chirality analysis through enantioselective adsorption on cysteine-modified gold surfaces. Quartz microbalance experiments and scanning electron microscope observation of the gold surface revealed that the colloidal particle has higher affinity to a surface modified with L-cysteine than to one modified with D-cysteine.