Production of Nitrogen-containing Sorbents from Wood Waste

The sorption capacity for Fe(II), Cu(II), Cd(II), and Zn(II) ions of nitrogen-containing derivatives of birch wood, obtained by different variations of oxidative ammonolysis, was studied.     

Purification and Biochemical Characterization of Two Xylanases from <Emphasis Type="Italic">Aspergillus sydowii</Emphasis> SBS 45

Two xylanases were isolated and purified from crude culture filtrate of Aspergillus sydowii SBS 45 after 9 days of growth on wheat bran containing 0.5% (w/v) birch wood xylan as the carbon source under solid-state fermentation. After a three-step purification scheme involving ammonium sulfate precipitation, gel filtration chromatography (Sephadex G-200), and anion exchange chromatography (DEAE-Sephadex A-50), xylanase I was purified 93.41 times, and xylanase II was purified 77.40 times with yields of 4.49 and 10.46, respectively. Molecular weights of xylanase I and II were 20.1 and 43 kDa, respectively, in sodium dodecyl sulfate-polyacrylamide gel electrophoresis. Optimum temperature was 50 degrees C, and optimum pH was 10.0 for both xylanase I and II. The Km value of xylanase I for birch wood xylan was 3.18 mg ml(-1) and for oat spelt xylan 6.45 mg ml(-1), while the Km value of xylanase II for birch wood xylan was 6.51 mg ml(-1) and for oat spelt xylan 7.69 mg ml(-1). Metal ions like Al3+, Ba2+, Ca2+, Na+, and Zn2+ enhanced the activity of xylanase I and II at 10 mM concentration. Among the additives, L-tryptophan enhanced the activity of xylanase I and II at 10-, 20-, and 30-mM concentrations. Both xylanases appeared to be glycoproteins.     

Influence of cellulose polymorphs on the polypropylene crystallization

Results of the hitherto research work on alkalisation of lignocellulosic materials have been much divergent. In view of the above, the subject of this study is mercerization of cellulose from pine wood. This choice of the subject permitted observation of transformation of cellulose I to cellulose II with no participation of other components of lignocellulosic materials. According to X-ray results, during mercerization the isolated cellulose was easily (completely) transformed into cellulose II variety, while the pine wood was converted more slowly to cellulose II polymorphs. Therefore, it could be concluded that the presence of lignin and hemicelluloses in wood prevented the transformation from cellulose I to II. The main objective of this research was to establish the effect of cellulose varieties on the nucleation ability of different fillers by using differential scanning calorimetry (DSC) and polarizing microscopy. The nucleating effect of the fillers occurs only in the presence of cellulose I variety. In contrast, the presence of cellulose II variety seems to practically eliminate the nucleating effect of the fillers. Moreover, nucleation of the mercerized wood (mixture of cellulose I and II) can be also observed, but this effect is not strong. It should be emphasised that as yet no correlation has been reported between the quantitative composition of cellulose polymorphic forms (appearing not only in wood, but in cellulose isolated from wood as well) and the nucleation ability of lignocellulosic fillers.     

Influence of wood mercerization on the crystallization of polypropylene in wood/PP composites

Mercerization process is very significant because the alkali treatment facilitates reactivity of lignocellulosic fillers, thus allowing better response to chemical modification. In the present study, the effect of mercerization of pine wood on the nucleation ability of polypropylene was investigated by means of differential scanning calorimetry. We discovered that for the composites with wood containing cellulose II, the decrease in the crystal conversion of the polymer matrix and increase in the half-time of crystallization values are significant. It can be concluded that the amount of cellulose II formed upon alkalization of lignocellulosic fillers determines their nucleation ability. To evaluate the transcrystalline effects caused by various woods, which were untreated or treated with sodium hydroxide, the polarized optical microscopy was also performed. The nucleation of polypropylene on the surface of wood was investigated by induction time measurement. It was found that surfaces of the unmodified wood generate epitaxial nucleation, whereas the mercerized wood generates nonepitaxial nucleation. The differences in the type of nucleation suggest that the effectiveness of formation of transcrystalline structures depends on the contribution of cellulose I and cellulose II. Moreover, the presence of epitaxy is not necessary for the appearance of transcrystalline structures. The results showed that the transcrystalline structures appeared in each system, even with wood containing significant contribution of cellulose II. The only difference noted was the change in the nucleation abilities of the wood surface. Results of this study imply the necessity of quantitative determination of the contributions of cellulose I and cellulose II, whose presence determine the type of nucleation and nucleation ability of the filler surface.     

Preparation of tough cellulose II nanofibers with high thermal stability from wood

Well-dispersed cellulose II nanofibers with high purity of 92 % and uniform width of 15–40 nm were isolated from wood and compared to cellulose I nanofibers. First, ground wood powder was purified by series of chemical treatments. The resulting purified pulp was treated with 17.5 wt% sodium hydroxide (NaOH) solution to mercerize the cellulose. The mercerized pulp was further mechanically nanofibrillated to isolate the nanofibers. X-ray diffraction patterns revealed that the purified pulp had been transformed into the cellulose II crystal structure after treatment with 17.5 wt% NaOH, and the cellulose II polymorph was retained after nanofibrillation. The cellulose II nanofiber sheet exhibited a decrease in Young’s modulus (8.6 GPa) and an increase in fracture strain (13.6 %) compared to the values for a cellulose I nanofiber sheet (11.8 GPa and 7.5 %, respectively), which translated into improved toughness. The cellulose II nanofiber sheet also showed a very low thermal expansion coefficient of 15.9 ppm/K in the range of 20–150 °C. Thermogravimetric analysis indicated that the cellulose II nanofiber sheet had better thermal stability than the cellulose I nanofiber sheet, which was likely due to the stronger hydrogen bonds in cellulose II crystal structure, as well as the higher purity of the cellulose II nanofibers.     

Sulfur and iron in shipwrecks cause conservation concerns

Synchrotron-based sulfur X-ray absorption spectroscopy reveals considerable accumulation of organosulfur (e.g. thiols), pyrite and iron(II) sulfides in marine-archaeological wood preserved in seawater, e.g. for historical shipwrecks such as the Vasa and Mary Rose. In the museum, oxidation of the sulfur compounds in the presence of iron ions may cause severe acidity in the moist wood. This tutorial review discusses developments of conservation methods to remove acid and iron, and how to analyse and stabilise sulfur compounds in the wood.     

A specific case in the classification of woods by FTIR and chemometric: discrimination of Fagales from Malpighiales

Fourier transform infrared (FTIR) spectroscopic data was used to classify wood samples from nine species within the Fagales and Malpighiales using a range of multivariate statistical methods. Taxonomic classification of the family Fagaceae and Betulaceae from Angiosperm Phylogenetic System Classification (APG II System) was successfully performed using supervised pattern recognition techniques. A methodology for wood sample discrimination was developed using both sapwood and heartwood samples. Ten and eight biomarkers emerged from the dataset to discriminate order and family, respectively. In the species studied FTIR in combination with multivariate analysis highlighted significant chemical differences in hemicelluloses, cellulose and guaiacyl (lignin) and shows promise as a suitable approach for wood sample classification.     

Enhanced saccharification of lignocellulosic biomass with1-allyl-3-methylimidazolium chloride（Amim Cl） pretreatment

A simple and efficient method of enhancing biomass saccharification by microwave-assisted pretreatment with dimethyl sulfoxide/1-allyl-3-methylimidazolium chloride is proposed. Softwood（pine wood（PW））, hardwoods（poplar wood, catalpa bungi, and Chinese parasol）, and agricultural wastes（rice straw, wheat straw, and corn stover（CS）） were exploited. Results showed that the best pretreatment effect was in PW with 54.3% and 31.7% dissolution and extraction ratios, respectively. The crystal form of cellulose in PW extract transformed from I to II, and the contended cellulose ratio and glucose conversion ratio reached 85.1% and 85.4%, respectively. CS after steam explosion achieved a similar pretreating effect as PW, with its cellulose hydrolysis ratio reaching as high as 91.5% after IL pretreatment.     

Two New Saturated Sesquiterpene Diols—Cadinan-3β, 9β-Diol and Cadinan-3β, 9α-Diol from Taiwania Cryptomerioides Hayata

From the wood of Taiwania cryptomerioides Hayata, two new sesquiterpenes, cadinan-3β, 9β-diol and cadinan-3β, 9α-diol were isolated as minor components. Their structures were elucidated as (I) and (II), respectively.     

Degrees of polymerization (DP) and DP distribution of cellouronic acids prepared from alkali-treated celluloses and ball-milled native celluloses by TEMPO-mediated oxidation

Various cellulose II samples, ball-milled native celluloses and ball-milled wood saw dust were subjected to 2,2,6,6-tetramethypyperidine-1-oxyl radical (TEMPO)-mediated oxidation to prepare cellouronic acid Na salts (CUAs). The TEMPO-oxidized products obtained were analyzed by ¹³C-NMR and size-exclusion chromatography (SEC). When the cellulose II samples with degrees of polymerization (DP) of 220–680 were used as the starting materials, the CUAs obtained had weight-average DP (DPw) values of only 38–79. Thus, significant depolymerization occurs on cellulose chains during the TEMPO-mediated oxidation. These DP values of CUAs correspond to the cellulose II crystal sizes along the chain direction in the original cellulose II samples, but not necessarily to their leveling-off DP values. CUAs can be obtained also from ball-milled native celluloses in good yields by TEMPO-mediated oxidation, although their DPw values are lower than about 80. On the other hand, CUA with DPw of about 170 was obtained from ball-milled wood saw dust.     

Interpenetration of wood with NH2R-functionalized silica xerogels anchoring copper(II) for preservation purposes

Interpenetration of wood samples of pine sapwood (Pinus sylvestris L.) with hybrid inorganic–organic silica xerogels bearing amine functions able to coordinate copper(II) cations has been successfully carried out. These materials have been prepared by sol–gel processing TEOS/APTES mixtures inside the wood. Solid state ²⁹Si NMR data provide evidence that the interpenetrated xerogel material has the same degree of condensation of the corresponding xerogel formed outside the wood. Copper(II) is effectively vehiculated inside the wood by coordination linkages with two ammine functions well evidenced by ESR measurements. SEM/EDX investigations show that the chlorine/copper atomic ratio inside the wood is lower than that of the starting salt CuCl₂, suggesting an exchange reaction with silanol groups with the formation of Si–O–Cu linkages and HCl. This reaction could be promoted by the excess of amine functions with formation of ammonium chloride species which remain onto the surface of the wood and in the mother solution owing to a higher degree of condensation. Sodium silicate was tested in place of TEOS in order to have a cheaper and ethanol-free formulation. However, gel penetration results significantly lower than that of the corresponding formulation containing TEOS and preservation performance are lower than that of TEOS formulation against brown-rot fungal decay.     

Production of levulinic acid from wood raw material in the presence of sulfuric acid and its salts

The catalytic activities of sulfuric acid and of cobalt(II), iron(III), and aluminum sulfates in the thermal splitting of the cellulose and wood of various species in the presence of superheated steam at 250–350°C under flow conditions and at 150–250°C under autoclave conditions have been studied. The yield of levulinic acid from cellulose reaches 35 wt-% and from wood 16.0–18.0 wt-%.Spruce, according to Table 3 and the experimental part-Translator.Institute of the Chemistry of Natural Organic Raw Material, Siberian Division, Russian Academy of Sciences, Krasnoyarsk, fax (3912) 43 93 42. Translated from Khimiya Prirodnykh Soedinenii, No. 2, pp. 226–230, March–April, 1998.     

Constituents of the leaves of Woodfordia fruticosa Kurz. I. Isolation, structure, and proton and carbon-13 nuclear magnetic resonance signal assignments of woodfruticosin (woodfordin C), an inhibitor of deoxyribonucleic acid topoisomerase II

Woodfruticosin (woodfordin C), a new cyclic dimeric hydrolyzable tannin having an inhibitory activity toward deoxyribonucleic acid (DNA) topoisomerase II, has been isolated from the leaves of Woodfordia fruticosa Kurz (Lythraceae) along with three known flavonol glycosides and three known flavonol glycoside gallates. The structure of wood fruticosin (woodfordin C) was determined by the use of two-dimensional nuclear magnetic resonance (2-D NMR) spectroscopy including heteronuclear multiple quantum coherence (HMQC) and heteronuclear multiple bond connectivity (HMBC) techniques. Detailed analyses of the proton and carbon-13 NMR (1H- and 13C-NMR) spectra of six known flavonoids were performed.     

Preservation of beech and spruce wood by allyl alcohol-based copolymers

Allyl alcohol (AA), acrylonitrile (AN), methyl methacrylate (MMA), monomers and monomer mixtures AA+AN, AA+MMA were used to conserve and consolidate Beech and Spruce. After impregnation, copolymerisation and polymerisation were accomplished by gamma irradiation. The fine structure of wood+polymer(copolymer) composites was investigated by Scanning Electron Microscopy (SEM). It was observed that copolymer obtained from AA+MMA monomer mixture showed the optimum compatibility. The compressional strength and Brinell Hardness Numbers determined for untreated and treated wood samples indicated that the mechanical strength of wood+copolymer composites was increased. It was found that the mechanical strength of the wood samples containing the AA+MMA copolymer was higher than the others. In the presence of P(AA/MMA), at highest conversion, the compressive strength perpendicular to the fibres in Beech and Spruce increased approximately 100 times. The water uptake capacity of wood+copolymer composites was observed to decrease by more than 50% relative to the original samples, and biodegradation did not take place.     

Quantitative determination of benzalkonium chloride in treated wood by solid-phase extraction followed by liquid chromatography with ultraviolet detection

Ammoniacal copper quat (ACQ) compound wood preservative is comprised of copper and quaternary ammonium compounds with benzalkonium chloride (BAC) as the active ingredient. Solid-phase extraction (SPE) followed by liquid chromatography with ultraviolet detection (LC-UV) was developed for quantitative determination of BAC in treated wood. Five species of wood were used, Japanese cedar (Cryptomeria japonica), Japanese larch (Larix leptolepis), Yezo spruce (Picea jezoensis), Sakhalin fir (Abies sachalinensis), and western hemlock (Tsuga heterophylla). BAC used in the present study was composed of 66% C12, 33% C14 and less than 1% C16. BAC was added to each wood species (500 mg) then extracted with HCl-ethanol (20 ml) and quantitatively determined with LC-UV (262 nm). Wood extractives from the heartwood of each species, except western hemlock, interfered with quantitative determination of BAC, but SPE with an Oasis MCX cartridge was effective in preventing this. Using the present methods, BAC homologue peaks were clearly confirmed without interference. Recoveries from wood ranged from 92 to 101% and the limit of quantitation was approximately 240 microg/g wood for the C12 and C14 homologues.     

A facile and novel process for the preparation of <Superscript>147</Superscript>Pm source

Aiming the selective recovery of palladium from high level radioactive liquid waste (HLW), a chelating thiamide type sorbent, CWP–TU, was prepared by the modification of Japanese cedar wood powder (CWP). Convection oven and microwave heating were separately used for modification purpose and found that microwave heating is more effective over oven heating. CWP–TU was extensively studied for the adsorption of Pd(II) from nitric acid medium. The batch test showed that nitric acid concentration of 3 M or higher is favorable for Pd(II) loading. Consistent adsorption of Pd(II) under gamma irradiation condition demonstrated the feasibility of using CWP–TU in real HLW. Also, Pd(II) only adsorption from simulated HLW solution verified the palladium only selectivity of the sorbent as well as the lack of influence of coexisting metal ions on its affinity toward Pd(II). CWP–TU holds maximum Pd(II) loading capacities of 0.98 mol/kg at 30 °C and 1.04 mol/kg under gamma irradiation. A comparative study using some ion exchange resins revealed that the resins are either ineffective in nitrate medium or lack stability under irradiation.     

Application of solid-phase extraction to quantitatively determine cyproconazole and tebuconazole in treated wood using liquid chromatography with UV detection

Solid-phase extraction (SPE) procedures were developed to avoid interference during the quantitative determination of cyproconazole and tebuconazole co-existing in wood extractives. Five species of wood were used, Japanese cedar (Cryptomeria japonica), Japanese larch (Larix leptolepis), Yezo spruce (Picea jezoensis), Sakhalin fir (Abies sachalinensis), and western hemlock (Tsuga heterophylla). Methanol extractives from the heartwood of all wood samples, except western hemlock, interfered with the quantitative determination of cyproconazole and tebuconazole using liquid chromatography (LC) with UV detection (LC-UV). SPE with Oasis MCX was effective in avoiding this interference. This method also reduced the time and volume of mobile phase required for LC-UV, since wood extractives with long retention times were also removed.     

Monitoring the polymerization process of polypyrrole films by thermogravimetric and X-ray analysis

Bio-composite fibers were developed from wood pulp and polypropylene (PP) by an extrusion process. The thermo-physical and mechanical properties of wood pulp-PP composite fibers, neat PP and wood pulp were studied using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic mechanical analysis (DMA). The thermal stability of bio-composite fibers was found to be significantly higher than pure wood pulp. An understanding into the melting behaviour of the composite system was obtained which would assist in selecting a suitable temperature profile for the extruder during processing. The visco-elastic properties of bio-composite fibers were also revealed from the study. The generated bio-composite fibers were also characterized using Fourier transform infrared spectroscopy (FTIR) to understand the nature of chemical interaction between wood pulp reinforcement and PP matrix. The use of maleated polypropylene (MAPP) as a compatibilizer was investigated in relation to the fiber microstructure. Changes in absorption peaks were observed in FTIR spectra of bio-composite fibers as compared to the pure wood pulp which indicated possible chemical linkages between the fiber and polymer matrix.     

Hydrogen bonding on accessible surfaces of cellulose from various sources and relationship to order within crystalline regions

Celluloses from a variety of common sources were analyzed for availabilities of O(2)H, O(3)H, and O(6)H in order to estimate the extent of hydrogen bonding on accessible fibrillar surfaces. Celluloses from flax, ramie, sisal, and wood (both cellulose I and II from wood) together with liquid NH₃-swollen cotton and NaOH-swollen cotton (cellulose II) had relative availabilities similar to those of native cotton. Celluloses from Valonia centricosa and in rayon samples stood apart from each other and from the “cotton family.” The difference between Valonia and cotton celluloses appears to result, in addition to the accepted smaller, less perfect crystallites in cotton, from an O(2)H hydrogen bond which is likely the intramolecular bond between O(2)H and O(6′)H that is present in Valonia and absent in cotton. Rayon samples also showed evidence of similar bonds involving O(2)H on accessible surfaces. Since the regenerated rayons had relative availabilities different from those of mercerized cotton and wood cellulose samples, it is proposed that chain packing arrangements are not the same in these two types of cellulose II.