Pressurized fluid extraction of polycyclic aromatic hydrocarbons using silanized extraction vessels

We have investigated the extraction efficiency of a pressurized fluid extraction system using an Ottawa sand matrix, soils and a certified reference material (HS-6) spiked with the 16 polycyclic aromatic hydrocarbon (PAHs) associated with method EPA 8100. Acceptable recoveries were achieved for all PAHs using a nominal sand concentration of 2.0 μg.g^-1. However, similar experiments that were conducted at a concentration of 0.20 μg.g^-1 afforded poor recoveries and poor reproducibility for the six-ring PAHs indeno(1,2,3-cd)pyrene, dibenz(a)anthracene, and benzo(ghi)perylene. These were not adequately addressed by the use of indeno(1,2,3-cd)pyrene-d12 and benzo(g,h,i)perylene-d12 surrogates. Silanization of vessels using dichlorodimethylsilane adequately passivates the system but is only required for the high surface area retention frits. Replicate analyses at concentrations of 200 and 20 ng.g^-1 demonstrated that detection limits in the low ppb range (ng.g^-1) are achieved for Ottawa sand, dry soil and soil with moisture contents up to a mass fraction of 30 %. Such performance is consistent with the analytical requirements of the Canadian Sediment Quality Guidelines. Improved analyte recoveries were also observed for the certified reference material HS-6 which were further improved by increasing extraction temperatures from 100 to 150 °C.

Pressurised liquid extraction of polycyclic aromatic hydrocarbons from contaminated soils

The reliability and efficiency of the pressurised liquid extraction technique (PLE) for extracting polycyclic aromatic hydrocarbons (PAHs) from contaminated soil has been investigated. Experimental design was used to study the influence of seven extraction variables (sample load, solvents used, solvent ratios, pressure, temperature, extraction time, and rinse volume). The results show that large sample loads in combination with small solvent volumes may result in low extraction efficiency. They also indicate that the recovery of low-molecular-mass PAHs is reduced by low extraction temperatures. The exact settings of the other variables are, however, less significant for the extraction efficiency. Repeated extractions at optimised settings of the tested variables show that PLE is an exhaustive extraction technique that generally results in high yields. In addition, extraction of a certified reference material (CRM 103-100) revealed that the method is both accurate and precise. Another finding was that adding the internal standard on top of the soil in the extraction cell causes considerable over-estimation of the concentrations when large samples are extracted with small solvent volumes. This is because the PLE-cell resembles a chromatographic column, so compounds added to the top of the soil layer have a longer distance to travel through the soil compared to the average distance of the native compounds, which are distributed evenly throughout the column. We therefore recommend that the internal standard should be added to the extract immediately after the extraction or, alternatively, carefully mixed with the sample prior to extraction.     

Ultrasonic micellar extraction of polycyclic aromatic hydrocarbons from marine sediments

In this present study the extraction of polycyclic aromatic hydrocarbons (PAHs) from marine sediments with a micellar medium of Polyoxyethylene 10 lauryl ether by an ultrasound-assisted method has been studied. Factorial design experiments were used in order to optimize the extraction parameters: extraction time, surfactant concentration and surfactant volume:amount of sediment relationship. The results suggest that surfactant concentration is statistically the most significant factor. The analysis of extracts has been carried out by HPLC with UV detection. Fortified sediments gave an average recovery between 86.7 and 106.6%, with relative standard deviation of 2.02-6.83% for PAHs with a ring number higher than three.     

Accelerated extraction for determination of polycyclic aromatic hydrocarbons in marine biota

A rapid and simple method is proposed for determination of polycyclic aromatic hydrocarbons (PAH) in complex matrices such as marine biota. The method uses sonication, by means of an ultrasonic probe, as a new tool for assisted extraction, coupled with reversed-phase liquid chromatography (RP-LC) with fluorescence detection (FL) for determination of 16 US EPA priority PAH. Separation and detection of the 16 PAH were complete in 45 min by RP-LC with a C₁₈ column and acetonitrile–water gradient elution. Multivariate optimisation of the variables affecting extraction (ultrasound radiation amplitude, sonication time, and temperature of the water-bath in which the extraction cell was placed) was conducted. The accuracy of the method was determined by analysis of a certified reference material and comparison of the results obtained with those from another method (microwave-assisted extraction and GC–MS). The new technique avoids the main problems encountered in the determination of PAH in complex matrices such as marine biota, and no clean-up step is necessary. The method was applied to determination of PAH in estuarine biota samples from the Urdaibai estuary (Biscay, Spain).     

Fluidized-bed extraction of polycyclic aromatic hydrocarbons from contaminated soil samples

Summary Due to the carcinogenity and ubiquity of polycyclic aromatic hydrocarbons in the environment they are of ongoing interest to analytical chemistry. In this study, a comparison of the classic Soxhlet extraction and, fluidized-bed extraction, has been conducted. The extraction of polycyclic aromatic hydrocarbons by this technique has been optimized considering as experimental variables the variation of the number of extraction cycles and the holding time after reaching the heating temperature by means of a surface response design. The significance of the operational parameters of the fluidized-bed extraction on the performance characteristics has been investigated. For the determination of the analytes a selective clean-up of the extracts followed by a fast gas chromatography method with mass spectrometric detection was used, resulting in low limits of detection (0.2 pg μL⁻¹). The accuracy of the complete analytical method was established by extraction and analysis of reference materials.     

Porous metal membranes for solid-phase extraction of polycyclic aromatic hydrocarbons

Solid-phase extraction (SPE) is one of the most important techniques for sample preparation, purification, concentration and cleanup. Membranes made from synthetic organic polymers, cellulose, or glass fibers are used for sample pretreatment. In this work, we report that a porous metal membrane, the metal filter in HPLC, was used as a novel kind of solid-phase extraction adsorbent material. To evaluate the performance of the porous metal membrane for the SPE, naphthalene, fluorene, anthracene, phenanthrene, fluoranthene, pyrene, chrysene, perylene and benzo(a)pyrene were selected as analytes. Several parameters that affected the extraction efficiency such as the extraction time, the concentration of NaCl, the extraction temperature and the agitation speed were optimized. The experimental result indicates that the porous metal membrane possesses high adsorption ability to the tested polycyclic aromatic hydrocarbons (PAHs). Under the optimum conditions, the detection limits of the developed method were in the range of 0.03-0.082 μg L(-1) (S/N = 5), and excellent linear correlations between peak area and concentration of PAHs were found over the range of 0.1-60 μg L(-1). The precisions (RSD) for five replicate extractions of the PAHs from sample solutions were in the range of 2.6-5.0%. The recoveries of the PAHs from tap water and river water samples spiked with 9 PAHs (20 μg L(-1) of each individual PAH) ranged from 83.0% to 112.5%. The porous metal membrane is durable, simple, inexpensive, reproducible and has a high adsorption ability for use in SPE of PAHs.     

Equilibrium partition of polycyclic aromatic hydrocarbons in a cloud-point extraction process

A cloud-point extraction (CPE) process using the nonionic surfactant Tergitol 15-S-7, a secondary ethoxylated alcohol, to extract selected polycyclic aromatic hydrocarbons (PAHs) from aqueous solutions is investigated. The CPE process is facilitated at the ambient temperature, ca. 22 degrees C, by the reduction of the cloud-point temperature of the surfactant solution by addition of sodium sulfate. It is observed that the preconcentration factor could be enhanced either by increasing the salt concentration or by decreasing the initial surfactant concentration in the micellar solution. A high preconcentration factor of about 40 was achieved at 1 wt% surfactant concentration with the addition of 0.6 M Na(2)SO(4). It is also noted that the equilibrium partition coefficients of the model PAHs are nearly independent of surfactant concentrations, up to 3 wt%, in this study. Correlations between the equilibrium partition coefficients K(p) of the PAHs and their octanol-water partition coefficients K(ow), as well as K(p) and the molar volume V(x) of these PAHs, indicate that the partition processes of the PAHs in the CPE processes are mainly governed by their hydrophobic affinities to the surfactant aggregates. Furthermore, the effect of added Na(2)SO(4) on the equilibrium partition coefficients is also studied. It is shown that addition of more Na(2)SO(4) to the surfactant solution gives more partition of the PAHs into the surfactant-rich phase.     

Comparative performance of extraction strategies for polycyclic aromatic hydrocarbons in peats

The assessment of historical trends in atmospheric deposition of organic contaminants by using peat samples has been reported on several occasions because these samples represent an almost ideal medium for recording temporal changes in organic contaminant deposition rates. The determination of polycyclic aromatic hydrocarbons (PAHs) in peat samples is complicated due to the high content of organic matter in peat, which affects both extraction efficiency and analytical quality. A rapid and simple method is proposed for the determination of 10 US Environmental Protection Agency indicator PAHs in complex matrices such as peat. This article reviews and addresses the most relevant analytical methods for determining PAHs in peat. We discuss and critically evaluate three different extraction procedures, such as ultrasound-assisted solvent extraction (UASE), shaking and pressurized liquid extraction (PLE). Clean-up of extracts was performed by solid-phase extraction using silica cartridges. Detection of the selected PAHs was carried out by high-performance liquid chromatography coupled with fluorescence detection for determination. Optimization of the variables affecting extraction by the selected extraction techniques was conducted, concluding that the UASE extraction method using hexane:dichloromethane (80:20) as extractant was robust enough to determine the selected PAHs in peat samples with estimated quantification limits between 0.050 and 3.5 μg/kg depending on the PAH. UASE did not demand sophisticated equipment and long extraction times. PLE involved sophisticated equipment and showed important variations in the results. The method proposed was applied to the determination of PAHs in peat samples from Xistral Mountains (Galicia, Spain).     

Improved ultrasonic extraction procedure for the determination of polycyclic aromatic hydrocarbons in sediments

The aim of this work was to optimize an ultrasonic extraction procedure for the determination of polycyclic aromatic hydrocarbons (PAHs) in sediments and to compare it with the reflux procedure using methanolic potassium hydroxide. Sample extracts were purified with a miniaturized silica gel chromatographic column and analyzed by gas chromatography-mass spectrometry (GC-MS). Ultrasonication using n-hexane-acetone (1:1, v/v) solvent mixture on dried homogenized marine sediment gave better precision (smaller relative standard deviation (RSD) values) and comparable quantities of individual PAH's compared to the reflux procedure. Ultrasonication with the n-hexane-acetone (1:1, v/v) mixture, utilizing four 15 min extraction cycles, was found to be sufficient for extracting PAHs from wet sediments. The optimized ultrasonic extraction procedure extracted aliphatic and aromatic hydrocarbons from the National Institute of Standards and Technology SRM 1941a with recoveries greater than 90%. The major advantages of ultrasonication compared to the reflux method are the lower extraction times, simplicity of the apparatus and extraction procedure. The optimized ultrasonication procedure has been used in our laboratory to extract hydrocarbons from naturally wet sediments from rivers, and coastal and marine areas.     

超分子溶剂直提测定水中的多环芳烃

超分子溶剂是两亲化合物通过分子间有序的自组装过程形成的具有纳米结构的胶束聚集体,是一种高效提取溶剂。该文以高效液相色谱-荧光检测法为测试手段,系统地对超分子溶剂组成及用量进行了优化,发展了一种直接提取、快速测定水中多环芳烃的方法,并进行了方法学验证及实际样品检测。结果表明,采用四氢呋喃和1-辛醇制备的超分子溶剂对4种多环芳烃的回收率为89.08%~102.47%,相对标准偏差(RSD,n=5)为1.38%~3.92%。4种多环芳烃在一定范围内线性关系良好(相关系数R~20.999),检出限为1.26~9.23 ng/L。该方法前处理过程简单,有利于实现快速分析;溶剂使用量少,符合绿色化学的发展趋势,具有一定的推广价值。     

Microwave assisted extraction of polycyclic aromatic hydrocarbons from atmospheric particulate samples

For several years, microwave assisted extraction (MAE) was applied to extract organic compounds such as polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls, etc., from soils, sediments and standard reference materials. Very few authors applied this methodology for the extraction of PAHs from atmospheric particulate matter. In the present study, MAE of polycyclic aromatic hydrocarbons with hexane/acetone (1:1) from real atmospheric particulate samples was investigated and the effect of microwave energy and irradiation time studied. The yields of extracted compounds obtained by microwave irradiation were compared with those obtained using traditional Soxhlet extraction. MAE was evaluated using spiked real atmospheric particulate samples and two standard reference materials. Analytical determinations of PAHs were carried out by high performance liquid chromatography (HPLC) with ultraviolet and fluorescence detection. The best recoveries were achieved with a microwave energy of 400 W and an irradiation time of 20 min.     

On the improvement of solid-phase extraction room-temperature phosphorimetry for the analysis of polycyclic aromatic hydrocarbons in water samples

This article presents considerable improvements in SPE-RTP methodology for the analysis of polycyclic aromatic hydrocarbons in water samples. Bulky glassware and vacuum pump were removed from the previous extraction procedure [E.D. Hagestuen, A.D. Campiglia, Talanta 49 (1998) 547] by processing 10 ml of sample with syringes and stainless steel filter holders. The oven-drying step was substituted by air sample drying, which employed positive pressure to remove water excess from the extraction membrane. As a result, analysis times from 8 to 10 min per sample were obtained. No costs in levels of detection were observed. Limits of detection at the pg ml(-1) level were estimated for phenanthrene, pyrene, benzo(k)fluoranthene, benzo(a)pyrene, and chrysene. The feasibility of identifying single components in PAH mixtures was investigated. Binary and tertiary mixtures were resolved by appropriate choice of excitation and emission wavelengths. The advantage of using excitation-emission matrix analysis was demonstrated for a six-component mixture.     

New procedure for selective extraction of polycyclic aromatic hydrocarbons in plants for gas chromatographic-mass spectrometric analysis

A new solid-phase extraction method for the clean-up and the quantitation by GC-MS of regulated polycyclic aromatic hydrocarbons (PAHs) from lettuce was developed and the experimental conditions were optimized. After ultrasonic extraction using toluene and saponification of samples, a clean-up of extracts through solid-phase extraction was performed. Samples were finally analyzed by gas chromatography-mass spectrometry (GC-MS) using an internal deuterated standard. Saponification by KOH in methanol-water (80:20) was successful allowing a good elimination of the interfering chlorophylls from the extracts containing the PAHs. The average recovery of the 16 regulated PAHs was 70, 74, 79 and 89%, respectively, for naphthalene, acenaphthylene, acenaphthene and chrysene and higher than 94% for the others.     

Comparison of various extraction techniques for the determination of polycyclic aromatic hydrocarbons in worms

Two less laborious extraction methods, viz. (i) a simplified liquid extraction using light petroleum or (ii) microwave-assisted solvent extraction (MASE), for the analysis of polycyclic aromatic hydrocarbons (PAHs) in samples of the compost worm Eisenia andrei, were compared with a reference method. After extraction and concentration, analytical methodology consisted of a cleanup of (part) of the extract with high-performance gel permeation chromatography (HPGPC) and instrumental analysis of 15 PAHs with reversed-phase liquid chromatography with fluorescence detection (RPLC-FLD). Comparison of the methods was done by analysing samples with incurred residues (n=15, each method) originating from an experiment in which worms were exposed to a soil contaminated with PAHs. Simultaneously, the performance of the total lipid determination of each method was established. Evaluation of the data by means of principal component analysis (PCA) and analysis of variance (ANOVA) revealed that the performance of the light petroleum method for both the extraction of PAHs (concentration range 1-30 ng/g) and lipid content corresponds very well with the reference method. Compared to the reference method, the MASE method yielded somewhat lower concentrations for the less volatile PAHs, e.g., dibenzo[ah]anthracene and benzo[ghi]perylene and provided a significant higher amount of co-extracted material.     

Comparison of different extraction methods for the determination of polycyclic aromatic hydrocarbons in soil

Two different extraction methods for the determination of polycyclic aromatic hydrocarbons in soil are compared: the extraction in combination with ultrasonic treatment, and the Soxhlet extraction method according to DIN-draft 38414 Part 21. Different types of real soil were extracted and analysed by HPLC with diode-array detector and fluorescence detection. The results show that the efficiency of the ultrasonic method is comparable to the Soxhlet method.     

Evaluation and optimization of extraction and clean-up methods for the analysis of polycyclic aromatic hydrocarbons in peat samples

The analysis of PAH in peat samples is complicated by the high content of organic matter in peat which affects both extraction efficiency and analytical quality. Therefore, we evaluated the efficiencies of three extraction methods (accelerated solvent extraction (ASE), fluidized bed extraction, ultrasonic extraction) and several clean-up techniques in order to find the best set of methods. ASE proved to be the best extraction method. For clean-up, a procedure using aluminium oxide and silica gel showed the highest efficiency, whereas a method originally developed for soil samples failed to remove the peat matrix satisfactorily. With the optimized extraction and clean-up procedure, 170 samples from Canadian bogs were analysed for PAH. With overall recovery rates between 69?±?14 and 89?±?16% and an inaccuracy of ≤20%, the optimized method was a well suitable tool for the analysis of PAH in peat samples.