Power test of the separated function RFQ accelerator

The progress of the Separated Function RFQ (SFRFQ) accelerator, which can raise the field gradient of acceleration while maintaining the transverse focusing power sufficient for high current beam, is presented. In order to demonstrate the feasibilities of the novel accelerator, a prototype cavity was designed and constructed. Correspondingly, a code SFRFQCODEV1.0 was developed specially for cavity design and beam dynamics simulation. The prototype cavity will be verified as a post-accelerator for ISR RFQ-1000 (Integral Split Ring RFQ) and     

Progress in the beam commissioning of separated function RFQ accelerator

Separated Function RFQ (SFRFQ) was proposed as a post accelerator of RFQ to accelerate heavy ions at low frequency. It introduces gap accelerating in the quadrupole electrodes, and therefore it has higher accelerating efficiency than the conventional RFQ accelerator. The first SFRFQ prototype cavity has been specially designed and constructed as a post accelerator to accelerate O+ beam from 1.03 MeV to 1.64 MeV. Based on accomplishment of low power measurement and high power test, the beam commissioning was carried out to verify its feasibility. The measured energy gain per cell of SFRFQ is 45 keV, which is about 60% higher than that of Peking University Integral Split Ring (ISR) RFQ.     

整体分离环RFQ加速器的研究

阐述了北京大学整体分离环高频四极场（ＩＳＲＲＦＱ）加速器研究所取得的研究成果．分别论述了２６ＭＨｚ３００ｋｅＶＩＳＲＲＦＱ加速器结构、束流动力学设计、高频控制系统、束流试验装置及束流试验；分析了其对Ｎ＋、Ｏ＋、Ｏ－束流试验的研究结果；简述了２６ＭＨｚ１ＭｅＶＲＦＱ加速器束流动力学、加速腔设计及目前的进展 The status of the ISR RFQ accelerators in Peking University is described. The structure of ISR RFQ accelerator, beam dynamics calculation results by PARMTEQ, RF systems, beam transport lines and the beam test evolutions of a 26 MHz 300 keV ISR RFQ accelerator are also presented, respectively. The beam test results for N +, O +, O - particles are analyzed in detail. At last, the development of 1 MeV 26 MHz ISR RFQ accelerator is introduced briefly.     

The radio-frequency design of an iris-type coupler for the CPHS radio-frequency quadrupole

The Compact Pulsed Hadron Source (CPHS) project is a university-based proton accelerator platform (13 MeV, 16 kW, 50 mA peak current, 0.5 ms pulse width at 50 Hz) for multi-disciplinary neutron and proton applications. The CPHS linac consists of a 3 MeV radio-frequency quadrupole (RFQ) linac and a 13 MeV drift tube linac (DTL). Both the RFQ and DTL share a 325 MHz, 2.1 MW klystron source. A single iris-type radio-frequency (RF) coupler is used to feed 537 kW of RF power to the RFQ cavity. Three-dimensional electromagnetic models of the ridge-loaded tapered waveguide (RLWG) and the coupler-cavity system are presented, and the design process and results of the RLWG and iris plate are described in detail.     

Accelerator development in India for ADS programme

At BARC, development of a Low Energy High Intensity Proton Accelerator (LEHIPA), as front-end injector of the 1 GeV accelerator for the ADS programme, has been initiated. The major components of LEHIPA (20 MeV, 30 mA) are a 50 keV ECR ion source, a 3 MeV Radio Frequency Quadrupole (RFQ) and a 20 meV drift tube linac (DTL). The Low Energy Beam Transport (LEBT) and Medium Energy Beam Transport (MEBT) lines match the beam from the ion source to RFQ and from RFQ to DTL respectively. Design of these systems has been completed and fabrication of their prototypes has started. Physics studies of the 20–1000 MeV part of the Linac are also in progress. In this paper, the present status of this project is presented.      

Design study of a radio-frequency quadrupole for high-intensity beams

The Rare isotope Accelerator Of Newness(RAON) heavy-ion accelerator has been designed for the Rare Isotope Science Project(RISP) in Korea. The RAON will produce heavy-ion beams from 660-MeV-proton to200-MeV/u-uranium with continuous wave(CW) power of 400 k W to support research in various scientific fields.Its system consists of an ECR ion source, LEBTs with 10 ke V/u, CW RFQ accelerator with 81.25 MHz and 500 ke V/u, a MEBT system, and a SC linac. In detail, the driver linac system consists of a Quarter Wave Resonator(QWR) section with 81.25 MHz and a Half Wave Resonator(HWR) section with 162.5 MHz, Linac-1, and a Spoke Cavity section with 325 MHz, Linac-2. These linacs have been designed to optimize the beam parameters to meet the required design goals. At the same time, a light-heavy ion accelerator with high-intensity beam, such as proton,deuteron, and helium beams, is required for experiments. In this paper, we present the design study of the high intensity RFQ for a deuteron beam with energies from 30 ke V/u to 1.5 MeV/u and currents in the m A range. This system is composed of an Penning Ionization Gauge ion source, short LEBT with a RF deflector, and shared SC Linac. In order to increase acceleration efficiency in a short length with low cost, the 2nd harmonic of 162.5 MHz is applied as the operation frequency in the D~+RFQ design. The D~+RFQ is designed with 4.97 m, 1.52 bravery factor. Since it operates with 2nd harmonic frequency, the beam should be 50% of the duty factor while the cavity should be operated in CW mode, to protect the downstream linac system. We focus on avoiding emittance growth by the space-charge effect and optimizing the RFQ to achieve a high transmission and low emittance growth. Both the RFQ beam dynamics study and RFQ cavity design study for two and three dimensions will be discussed.     

Design studies of a high-current radiofrequency quadrupole for accelerator-driven systems programme

A 3 MeV, 30 mA radiofrequency quadrupole (RFQ) accelerator has been designed for the low-energy high-intensity proton accelerator (LEHIPA) project at BARC, India. The beam and cavity dynamics studies were performed using the computer codes LIDOS, TOUTATIS, SUPERFISH and CST microwave studio. We have followed the conventional design technique with slight modifications and compared that with the equipartitioned (EP) type of design. The sensitivity of the RFQ to the variation of input beam Twiss-Courant parameters and emittance has also been studied. In this article we discuss both design strategies and the details of the 3D cavity simulation studies.     

Physics design of a CW high-power proton Linac for accelerator-driven system

Accelerator-driven systems (ADS) have evoked lot of interest the world over because of their capability to incinerate the MA (minor actinides) and LLFP (long-lived fission products) radiotoxic waste and their ability to utilize thorium as an alternative nuclear fuel. One of the main subsystems of ADS is a high energy (∼1 GeV) and high current (∼30 mA) CW proton Linac. The accelerator for ADS should have high efficiency and reliability and very low beam losses to allow hands-on maintenance. With these criteria, the beam dynamics simulations for a 1 GeV, 30 mA proton Linac has been done. The Linac consists of normal-conducting radio-frequency quadrupole (RFQ), drift tube linac (DTL) and coupled cavity drift tube Linac (CCDTL) structures that accelerate the beam to about 100 MeV followed by superconducting (SC) elliptical cavities, which accelerate the beam from 100 MeV to 1 GeV. The details of the design are presented in this paper.     

四轩型RFQ加速腔高频特性的数值模拟与实验研究

为设计一个高负载因子、高流强的RFQ加速器，使用三维电磁场计算程序MAFIA对加速腔的高频特性进行了模拟计算. 本文主要研究RFQ支撑板高度、宽度、间距、电极形状等结构参数对高频腔体高频特性的影响，根据RFQ加速器的比分路阻抗以及电磁场分布的要求，对RFQ的结构参数进行优化设计，然后根据模拟计算结果加工冷模，进行冷模测量并将测量结果与计算结果加以比较.     

强流四杆型RFQ加速腔水冷系统的设计和数值模拟

为了研制一个强中子发生器，北京大学重离子物理研究所设计了一台高负载因子、高流强的RFQ加速器. 本文讨论了RFQ加速腔水冷系统的设计，使用有限元软件ANSYS对水冷系统进行了分析. 使用MAFIA模拟计算得到的功率密度，并将其作为ANSYS水冷模型的边界条件. 因为MAFIA程序和ANSYS程序分网方法的不同，使用一个程序来将MAFIA的结果导入到ANSYS模型中，从而建立起了RFQ加速腔的热分析模型. 通过这个热分析模型分析并检验了水冷系统的设计，确定了水冷系统的结构. 模拟计算结果表明：使用目前设计的这套水冷系统，能够使RFQ加速器工作在适宜的温度下以及长时间稳定的运行.     

The Design and Simulation of a Cooling System of High Current 4-rod RFQ Cavity

To develop a high current neutron generator, preliminary studies on a high current, high duty factor 4-rod RFQ accelerator has been carried out in the Institute of Heavy Ion Physics,Peking University. This paper discusses the design of a cooling system of the RFQ cavity. Finite element program ANSYS was used to analyze the cooling system. The power density was simulated by MAFIA and used as the boundary condition of ANSYS. Due to the different meshing methods between MAFIA and ANSYS, a program was written to transfer the result of MAFIA to ANSYS. Then a thermal analysis model of RFQ cavity was built by using ANSYS. The design of the cooling system was analyzed and checked by using this model, and then the structure of cooling system is determined. Simulation results showed that the design of the cooling system makes RFQ accelerator working at proper temperature and long time steadily.     

大功率辐照加速器的研制

介绍了10MeV/20kW大功率辐照加速器的设计. 该加速器采用返波型行波加速结构加速管, 综合了常规行波加速结构微波反射小、频率稳定性好和驻波加速结构分流阻抗高的优点. 加速器工作于S波段, 中心频率为~2856MHz. 利用自编的模拟程序AccDesign进行物理设计, 设计输出电子束能量为10MeV, 脉冲流强300mA, 加速管总长1.5m, 模拟计算结果显示微波至电子束的转换效率为66%. 同时利用计算机仿真程序对加速腔的温度和应力分布进行了计算, 得到了微波功率损耗对加速腔频率的影响.     

Preliminary design studies of a 100 MeV H−/H+ LINAC as injector for SNS synchrotron/ADS LINAC

It is proposed to construct a spallation neutron source (SNS) at Centre for Advanced Technology (CAT) based on a 1 GeV proton synchrotron with 100 MeV H⁻ LINAC as injector. Additionally, the LINAC can form the first 100 MeV part of a 1 GeV proton LINAC to be built in future for accelerator driven system (ADS) applications. We are exploring a configuration of the 100 MeV LINAC which will consist of an H⁻ ion source, a 4–6 MeV RFQ followed either by a 20 MeV drift tube LINAC (DTL) and 100 MeV separated function drift tube LINAC (SDTL) or a coupled cavity drift tube LINAC (CCDTL) structure. In this paper, we present the results of our preliminary physics design studies of the RFQ-SDTL, RFQ-CCDTL and RFQ-DTL-SDTL configurations. The design of the 4.5 MeV RFQ is discussed along with the matching sections between the RFQ-SDTL/DTL and RFQ-CCDTL. The choice of the accelerator configuration and that of various parameters of the individual accelerator structures under consideration are discussed. The design objectives are to arrive at a configuration which eases heat removal for CW operation and which is less prone to halo formation in order to reduce the beam loss at higher energies.     

SSC直线注入器RFQ腔体多物理场分析

SSC-LINAC是为兰州重离子研究装置（HIRFL）设计的直线注入器,它将U34+离子加速到1 MeV/u注入到分离扇回旋加速器（SSC）中,为冷却储存环（CSR）提供10 MeV/u的U34+。该注入器可以将SSC引出的重离子流强提高一个量级以上。SSC-LINAC由一个RFQ（Radio Frequency Quadrupole）加速器和4个DTL（drift tube linac）组成,设计频率为53.667 MHz。RFQ工作在连续波模式,设计功率30 kW,如果不能有效地冷却,高频电流在电极表面产生的热量会使RFQ的腔壁和电极发生形变,从而导致腔体频率的漂移以及加速和聚焦电场的改变。因此,为了保证连续波工作的RFQ加速器稳定运行,对水冷模式和通道设计提出了很高的要求。作者用有限元软件ANSYS对RFQ进行高频电磁场、温度场、结构应力的耦合分析,验证了冷却方案设计的可行性和可靠性。Heavy Ion Research Facility at Lanzhou(HIRFL) consists of SFC, SSC, CSRm and CSRe. A new linac injector, which will increase U34+ to 1 MeV/u, is designed for SSC to increase the beam intensity to ten times higher. The new injector, whose frequency is 53.667 MHz, is composed by a RFQ (Radio Frequency Quadrupole) cavity and four DTL(Drift Tube Linac) cavities. The RFQ cavity, whose RF power is 30 kW, is operated at CW(continuous wave) mode. The heat produced by HF (high frequency) electromagnetic will cause deformation of RFQ structure, lead to the resonant frequency shift, and reduce the focusing efficiency of the cavity. An efficient cooling system is necessary to ensure that the RFQ cavity can stably be operated at the nominal frequency. A detailed multi-physics field coupling analysis of RFQ has been finished with 3D finite elements software ANSYS. The result of the analysis shows that the water cooling system can cool the RFQ cavity fully and keep the frequency drift be in a acceptable level.     

中国散裂中子源直线射频功率源系统的研制

中国散裂中子源加速器质子束流加速能量为1.6 GeV,重复频率为25 Hz,撞击固体金属靶产生散射中子,一期工程的打靶束流功率为100 kW。直线加速器的设计束流流强为15 mA,输出能量为81 MeV。射频加速和聚束系统包括一台射频四极场加速器、中能束流传输线的两个聚束器、四节漂移管直线加速器加速腔和直线-环束流传输线的一个散束器,与之相对应,共有8个单元在线运行的射频功率源为其提供所需的射频功率。目前,直线射频功率源系统预研项目已全部完成,各项性能参数均已达到设计指标,当前正处在批产安装调试阶段。151013     

硼中子俘获治疗实验装置射频功率源系统

中国科学院高能物理研究所建造了一台基于加速器的硼中子俘获治疗（BNCT）实验装置。射频功率源系统为352.2 MHz射频四极加速器（RFQ）提供高频功率,使束流离开RFQ时,其能量达到3.5 MeV。BNCT射频功率源系统主要包括速调管功率源、数字低电平控制系统、射频传输系统。本文介绍了BNCT射频功率源系统,主要包括物理需求、系统组成、关键设备、安装和调试。目前该装置已进行动物实验,加速器打靶束流功率4.3 kW,加速器射频功率源系统运行稳定。     

用于1MeV 分离作用RFQ加速器改造的ECR氧离子源及LEBT系统的研制

An ECR O~ ion source and LEBT system have been developed for the upgrade of 1MeV Integral Split Ring RFQ at Peking University.To satisfy the requirement of RFQ,a more than 10mA oxygen beam has been extracted at 22kV through a 5mm diameter aperture.Its normalized root-mean-square emmitance is less than 0.1π·mm·mrad,which is required by RFQ accelerator.The LEBT matching section is redesigned upon the bench test results.The preliminary results will be presented in this paper.     

Beam Dynamics Design of a 50 mA D~+ RFQ

A new 973 project was proposed by Peking University and Institute of Modern Physics of Chinese Academy of Sciences recently.The project requires a 50 mA,162.5 MHz,cw mode radio frequency quadrupole(RFQ)to accelerate the D~+ to 1 MeV.In a high-current linear accelerator,the strong space charge effect causes the growth of envelope and emittance along with heavy beam losses.In the beam dynamics design of this RFQ,beam envelope mismatching is discussed and a matching dynamics method is proposed to minimize the envelope and emittance growth.The influence of limiting current on the beam transmission is discussed and used in the optimization of transverse and longitudinal parameters.After the optimization,the beam transmission efficiency reaches higher than 98%.     

Studies on RFQ accelerators and its applications

Development activities of Radio Frequency Quadrupole (RFQ) accelerators in China are presented.A 1 MeV O~+ RFQ and a 3.5 MeV ADS proton RFQ have been constructed.A novel separated function RFQ is under beam test, a 2 MeV D~+ RFQ is under construction and a CSNS RFQ is going to be constructed.The RFQ dynamics and the simultaneous dual beam acceleration with positive and negative ions were investigated and related codes were developed.The applications of RFQ will be further promoted in China.     

IH型漂移管直线加速器的束流动力学研究（英文）

为了提高兰州重离子加速器冷却储存环（HIRFL-CSR）的运行效率、改善加速器输出束流品质,并实现几个加速装置分时供束,提高整个重离子加速装置的利用率,特为（HIRFL-CSR）增建一台新的注入器--CSRLINAC。在108.48 MHz的RFQ之后的CSR-LINAC主加速段,主要由一台108.48 MHz和两台216.96 MHz的IH型漂移管直线加速器组成,用于加速荷质比为1/8.5~1/3之间的重离子,其最大的束流流强为3 mA,并将粒子从0.3 MeV/u加速到3.71 MeV/u。运用KONUS动力学原理,在满足设计指标的情况下,首先利用TraceWin程序进行中能束线MEBT设计,后针对高频腔体设计和束流匹配的基本参数的系列讨论,特别是对CSR-LINAC的中能束流匹配线、参数选择和IH型KONUS结构的漂移管直线加速器进行设计模拟优化。最终得出,在保证腔体设计指标和95.3%的传输效率的情况下,该紧凑型直线加速结构经过三个腔体的加速后,束流的纵向归一化均方根发射度增长仅有25%;同时发现,当流强达到3 mA时,存在空间电荷效应,导致其纵向相宽增长约25%,最大横向包络也存在16.5%的涨落。In order to improve the operation efficiency of the Cooling Storage Ring of Heavy Ion Research Facility in Lanzhou (HIRFL-CSR), a heavy ion linac (linear accelerator) was proposed and designed as a new injector for HIRFL-CSR. Following the 108.48 MHz Radio-Frequency Quadrupole (RFQ), three tanks in total with Interdigital H-mode drift tube linac (IH-DTL) structure are installed to boost the beam energy from 0.3 to 3.71 MeV/u, and the beam current of ions with charge-to-mass ratio from 1/8.5 to 1/3 can reach to 3 mA. The first tank operatesat the same frequency as the RFQ, and the rest two operate at 216.96 MHz. The “Combined Zero-Degree Synchronous Particle Structure” (KONUS) beam dynamics was used in the beam dynamics design. The overview of the physics design on the main accelerating components, including RF design and beam dynamics design are introduced in this paper. The optimized structure design, fabrication status and simulation results are presented in this contribution. It shows that under the condition of assurance of 95.3% transmission efficiency, the normalized rms emittance is about 25%. When the beam current is up to 3 mA, owing to the space charge effect, the increase of longitudinal phase spread and transverse envelope are about 25% and 16.3%, respectively.