A facile method for the preparation of monodisperse hollow silica spheres with controlled shell thickness

This article presents a facile, effective, mild synthesis process for well‐defined hollow spheres by using cationic polystyrene (PS) submicro‐particles as templates. In this approach, the cationic PS templates can be first prepared via emulsifier‐free polymerization by using the cationic monomer 2‐(methacryloyloxy) ethyltrimethylammonium chloride as comonomer, then, the silica shells from the sol‐gel process of tetraethoxysilane were coated on the surfaces of template particles via electrostatic interaction, finally the PS was dissolved in situ by modification of the reaction conditions in the same medium to form monodisperse hollow silica spheres with controlled shell thickness. Fourier transform‐infrared spectroscopy, thermogravimetric analysis, Brunauer‐Emmett‐Teller, transmission electron microscopy, and scanning electron microscope measurements were used to characterize these hollow silica spheres. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 1332–1338, 2010     

以手性两亲小分子自组装体为模板制备介孔二氧化硅空心球

合成了手性阳离子型两亲性小分子化合物,利用圆二色谱分析了其在水中形成的自组装体的结构;以该化合物的自组装体为模板,在正丙醇和氨水的混合溶剂中制备得到了介孔二氧化硅空心球;利用扫描电镜、透射电镜、X射线衍射仪以及氮气吸附-脱附试验装置分析了二氧化硅空心球的形貌及孔结构.结果表明,两亲性小分子在水中形成的自组装体呈现手性堆积;合成的介孔二氧化硅空心球的直径约为600~800nm,壁厚约为100~150nm,其孔道垂直于球的表面,孔径约为3.0nm,比表面积约为306m2·g-1.正丙醇作为模板控制二氧化硅空心球的空腔尺寸和形貌,而两亲性小分子的自组装体作为模板控制放射状孔道的形貌和尺寸.     

Density fractionated hollow silica microspheres with high-yield by non-polymeric sol–gel/emulsion route

Hollow silica microspheres were synthesized by non-polymeric sol–gel/emulsion technique using tetra ethyl orthosilicate (TEOS) as a source of silica. A sol mixture of TEOS, water, ethanol and acid was emulsified in a solution of light paraffin oil and surfactant (Span-80). Calcined spheres were density fractionated between density ranges: <1.0, 1.0–1.594, 1.594–1.74 and >1.74 g cm⁻³. The samples were characterized by optical and scanning electron microscopy with energy dispersive X-ray analysis, Fourier transform infrared spectroscopy and laser diffraction size analyzer. Spheres of densities lower than 1.74 g cm⁻³ were found to be hollow as observed from scanning electron microscopy (SEM) images and their yield was maximized to 100% by using a specific TEOS volume ratio with respect to volumes of surfactant and oil. Decreasing the calcination temperature from 700 to 500 °C enhances the yield of hollow spheres emphasizing importance of slower diffusion kinetics at lower calcination temperature. Outer diameters of spheres were between 5 and 60 μm with mean diameter expectedly increasing with increase in TEOS sol volume and with decrease in sphere density. It is proposed that silica shells form via hydrolysis and polycondensation at oil–water/ethanol interface in the water-in-oil emulsion, which subsequently form hollow spheres on removal of water–ethanol during calcination.     

A novel method for the fabrication of monodisperse hollow silica spheres

In this paper, we report a novel method for the fabrication of small monodisperse hollow silica spheres. In this approach, when silica shells were coated on polystyrene particles by the sol-gel method, the polystyrene cores were dissolved subsequently, even synchronously, in the same medium to form monodisperse hollow spheres. Neither additional dissolution nor a calcination process was needed to remove the polystyrene cores. Transmission electron microscopy, scanning electron microscopy, and porosity measurements were used to characterize the monodisperse hollow silica spheres.     

可用于色谱固定相的介孔氧化硅球材料的合成

采用非离子型嵌段高分子表面活性剂EO₂₀PO₃₀EO₂₀ (P65)为结构导向剂, 正硅酸乙酯为硅源, 在酸性介质中, 静置法制备了微米级介孔氧化硅球. 通过改变合成温度、反应时间或者无机盐KCl的加入量, 可以调节介孔氧化硅球的直径(9.0～17.6 μm); 加入1,3,5-三甲苯(TMB)或者调节水热温度, 可以调节介孔氧化硅球的孔径(2.3～4.8 nm). 采用X射线衍射(XRD)、N₂吸附-脱附、扫描电镜(SEM)、激光散射粒度分布和对溶菌酶的吸附等方法, 对介孔氧化硅球的结构、孔性质、形貌、吸附性质等进行了表征. 实验发现, 孔径较小的介孔氧化硅球(≤4.3 nm)对溶菌酶的吸附不明显(≤42 mg/g), 而孔径(4.8 nm)大于溶菌酶直径的材料对溶菌酶有较大的吸附量(192 mg/g), 说明孔径均匀可调的介孔氧化硅球材料可以很好地用作体积排阻色谱柱的固定相.     

A facile method of synthesis of asymmetric hollow silica spheres

This paper presents a "one-step" method to synthesize asymmetric hollow silica spheres. In this method, when positively charged polystyrene particles were blended with mercaptopropyltriethoxysilane and stirred at 50 °C in alkaline ethanol/water medium for a period of time, Janus or lobed asymmetric hollow silica spheres could be directly obtained, just changing the ratio of ethanol to water in the reaction medium. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) were used to characterize the morphology and topography of the asymmetric hollow silica spheres. The formation mechanism was described in detail.     

Fabrication of hollow silica microspheres utilizing a hydrothermal approach

Hollow silica microspheres(HSMSs) have been successfully fabricated via a facile hydrothermal route using D-glucose as the sacrificial template and sodium silicate powder as the silica precursor.The resulting silica hollow particles were characterized by scanning electron microscopy(SEM),transmission electron microscopy(TEM),X-ray diffraction(XRD),and infrared spectroscopy(IR).The surface area was determined using the BET method.SEM and TEM images exhibited micro-sized silica hollow particles with a size of ~1.5μm.     

Fabrication of silica nanoparticles and hollow spheres using ionic liquid microemulsion droplets as templates

Silica products with two different morphologies were synthesized using nonaqueous ionic liquid microemulsion droplets as templates. The morphologies of the obtained products were characterized by both transmission electron microscopy (TEM) and scanning electron microscopy (SEM). By adjusting the reaction conditions, ellipsoidal nanoparticles were formed under acidic conditions, while hollow silica spheres were obtained under alkaline conditions. It is demonstrated that the size distribution of hollow silica spheres was narrower than that of the ellipsoidal nanoparticles. The various vibration modes of different functional groups in the silica materials were revealed by Fourier transform infrared (FTIR) spectroscopy. The two samples were both shown to be amorphous, not crystalline by X-ray diffraction (XRD). A simple diagram of the formation process including the hydrolysis and condensation reactions is given. Furthermore, a probable mechanism for the formation of silica materials under acidic or alkaline conditions is presented, which may be helpful for better understanding the different silica materials obtained under different conditions.     

Fabrication and photocatalytic properties of SnO2 double-shelled and triple-shelled hollow spheres

SnO₂ double-shelled and triple-shelled hollow spheres were tailored by adjusting concentration of tin (IV) chloride solution during the process of the tin (IV) ions infused carbonaceous spheres. The structures of these SnO₂ multi-shelled hollow spheres were examined by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and their possible formation mechanism were also discussed. In virtue of triple-shelled hollow porous structure and higher specific surface area, SnO₂ triple-shelled hollow spheres exhibited enhanced photocatalytic properties compared to SnO₂ double-shelled hollow spheres.     

Synthesis of hollow spherical silica with MCM-41 mesoporous structure

Hollow spherical mesoporous silica was synthesized by using sodium silicate as a precursor and a low concentration of cetyltrimethylammonium bromide (CTAB) (0.154 mol dm^–3). The resulting hollow spherical particles were characterized with scanning electron microcopy (SEM), small-angle X-ray diffraction (SXRD), transmission electron microscopy (TEM), and N₂ gas adsorption and desorption techniques. The results showed that regular spherical mesoporous silica could be obtained only if the molar ratio of propanol to CTAB was in the range of approximately 8:1–9:1. The spherical particles were hollow (inside), and the shell consisted of smaller particles with a pore structure of hexagonal symmetry. With an increase of the molar ratio of propanol to CTAB, the distance (a value) between centers of two adjacent pores increased, and the pore structure of mesoporous silica became less ordered. N₂ adsorption–desorption curves revealed type IV isotherms and H1 hysteresis loops; with an increase of the molar ratio of propanol to CTAB, the pore size with Barrett–Joyner–Halenda (BJH) diameter of the most probable distribution decreased, but the half peak width of the pore size distribution peak increased     

Preparation of hollow silica microspheres with controlled shell thickness in supercritical fluids

This article presents a novel route to prepare hollow silica microspheres with well-defined wall thickness by using cross-linked polystyrene (PS) microspheres as templates with the assistance of supercritical carbon dioxide (SC-CO₂). In this approach, the cross-linked PS templates can be firstly prepared via emulsifier-free polymerization method by using ethylene glycol dimethacrylate or divinylbenzene as cross-linkers. Then, the silica shell from the sol–gel process of tetraethyl orthosilicate (TEOS) which was penetrated into the PS template with the assistance of SC-CO₂ was obtained. Finally, the hollow silica spheres were generated after calcinations at 600 °C for 4 h. The shell thickness of the hollow silica spheres could be finely tuned not only by adjusting the TEOS/PS ratio, which is the most frequently used method, but also by changing the pressure and aging time of the SC-CO₂ treatment. Fourier transform infrared spectroscopy, transmission electron microscopy, and scanning electron microscope were used to characterize these hollow silica spheres.     

Influence of substrate stiffness on cell-substrate interfacial adhesion and spreading: a mechano-chemical coupling model

Highly ordered three dimensionally macroporous carbon spheres (3DMPCS) were successfully prepared against removable colloidal silica crystal bead templates by carbonization of glucose. The unique structural characteristics of the well-developed three dimensionally interconnected macropores were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and nitrogen adsorption. The 3DMPCS have uniform large pore structures with size about 250 nm. Pt nanoparticles were supported on the macroporous carbon spheres by two aqueous impregnation methods, and it was found that the 3DMPCS supported Pt exhibited high electrocatalytic activity for methanol oxidation.     

Sonochemical synthesis of hollow PbS nanospheres

PbS hollow nanospheres with diameters of 80-250 nm have been synthesized by a surfactant-assisted sonochemical route. The nanostructures were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), (high-resolution) transmission electron microscopy [(HR)TEM], and scanning electron microscopy (SEM) images. Structural characterization indicates that shells of the hollow spheres are composed of PbS nanoparticles with diameters of about 12 nm. The formation of the hollow nanostructure was explained by a vesicle-template mechanism, in which sonication and surfactant play important roles. Furthermore, uniform silica layers were successfully coated onto the hollow spheres via a modified St?ber method to enhance their performance for promising applications.     

Synthesis and characterization of surface modified SBA-15 silica materials and their application in chromatography

Hexagonally ordered SBA-15 mesoporous silica spheres with large uniform pore diameters are obtained using the triblock copolymer, Pluronic P123, as template with a cosurfactant cetyltrimethylammonium bromide (CTAB) and the cosolvent ethanol in acidic media. A series of surface modified SBA-15 silica materials is prepared in the present work using mono- and trifunctional alkyl chains of various lengths which improves the hydrothermal and mechanical stability. Several techniques, such as element analysis, nitrogen sorption analysis, small angle X-ray diffraction, scanning electron microscopy (SEM), FTIR, solid-state (29)Si and (13)C NMR spectroscopy are employed to characterize the SBA-15 materials before and after surface modification with the organic components. Nitrogen sorption analysis is performed to calculate specific surface area, pore volume and pore size distribution. By surface modification with organic groups, the mesoporous SBA-15 silica spheres are potential materials for stationary phases in HPLC separation of small aromatic molecules and biomolecules. The HPLC performance of the present SBA-15 samples is therefore tested by means of a suitable test mixture.     

SnO2 hollow spheres:Polymer bead-templated hydrothermal synthesis and their electrochemical properties for lithium storage

SnO2 hollow spheres have been synthesized via a facile hydrothermal method using sulfonated polystyrene beads as a template followed by a calcination process in air.X-ray diffraction,scanning electron microscopy,and transmission electron microscopy show that the as-obtained SnO2 hollow spheres have a wall thickness of about 50 nm,and consist of nanosized SnO2 particles with a mean diameter of about 15 nm.Electrochemical measurements indicate that the SnO2 hollow spheres exhibit improved electrochemical performance in terms of specific capacity and rate capability in comparison with commercial SnO2 when used as anode materials for lithium-ion batteries.The enhanced performance may be attributed to the spherical and hollow structure,as well as the building blocks of SnO2 nanoparticles.     

自催化还原制备微米和纳米级空心镍球的研究

提出了一种新型的制备超细空心金属镍粉的方法.通过FESEM,TEM和XRD衍射对该制备方法进行了研究,并考察了有关工艺参数对产物粒径和粒度分布的影响.研究认为,通过在胶核表面发生自催化还原反应,形成金属镍壳,同时胶核发生自分解,最后可得到空心金属镍球.控制反应物浓度和NaOH的配比可得到粒径均匀的镍球;通过调整这两个参数可得到粒度在微米或纳米尺度的空心镍球.     

中空TiO_2微球的制备及对聚丙烯酸酯薄膜性能的影响

采用阳离子聚苯乙烯微球作为模板,钛酸四丁酯为钛源,氨水为催化剂,制备了中空TiO_2微球.采用X射线衍射、扫描电镜及比表面测定仪对其形貌和结构进行了表征,并考察了模板粒径、钛源用量以及催化剂用量对中空TiO_2微球形貌的影响.通过物理共混法将其引入至聚丙烯酸酯乳液中并成膜,研究了复合薄膜的保温性能、抗紫外性能及力学性能.结果表明,锐钛矿相中空TiO_2微球模板粒径、钛源用量以及催化剂用量影响中空TiO_2微球的空心尺寸、壁厚及壳层致密性.中空TiO_2微球可显著提升聚丙烯酸酯薄膜的保温性能、抗紫外性能和力学性能.采用不同粒径的模板制备的中空TiO_2微球对复合薄膜的各项性能均有影响,其中模板粒径为140 nm时复合薄膜性能最优,光反射率提升63%,导热系数降低27%,且在波长小于360 nm范围内,紫外透过率几乎为0,抗张强度增加100%,断裂伸长率提升62%.     

新型氧化铝空心球的制备及表征

以胶体碳球为模板, 廉价的硝酸铝为铝源, 成功制备出了新型的大小可控的氧化铝空心球. 通过透射电子显微镜(TEM)、扫描电子显微镜(SEM)、能量扩散X射线(EDX)、X射线粉末衍射(XRD)等手段对合成产品进行了表征, 并考察了不同合成条件对空心球形貌的影响. 实验结果表明, 合成的氧化铝空心球大小均一, 粒径及壁厚均可调节. 在该实验条件下, 硝酸铝浓度及吸附时间的改变对产品结果没有明显的影响, 而吸附温度的改变引起了产品表面光滑度及壁厚的改变.     

A General Route to Hollow Mesoporous Rare‐Earth Silicate Nanospheres as a Catalyst Support

Hollow mesoporous structures have recently aroused intense research interest owing to their unique structural features. Herein, an effective and precisely controlled synthesis of hollow rare‐earth silicate spheres with mesoporous shells is reported for the first time, produced by a simple hydrothermal method, using silica spheres as the silica precursors. The as‐prepared hollow rare‐earth silicate spheres have large specific surface area, high pore volume, and controllable structure parameters. The results demonstrate that the selection of the chelating reagent plays critical roles in forming the hollow mesoporous structures. In addition, a simple and low‐energy‐consuming approach to synthesize highly stable and dispersive gold nanoparticle–yttrium silicate (AuNPs/YSiO) hollow nanocomposites has also been developed. The reduction of 4‐nitrophenol with AuNPs/YSiO hollow nanocomposites as the catalyst has clearly demonstrated that the hollow rare‐earth silicate spheres are good carriers for Au nanoparticles. This strategy can be extended as a general approach to prepare multifunctional yolk–shell structures with diverse compositions and morphologies simply by replacing silica spheres with silica‐coated nanocomposites.     

Green preparation of hollow mesoporous silica nanosphere inside-loaded gold nanoparticles and the catalytic activity

In this work, an active nano-catalyst with gold nanoparticles loaded in hollow mesoporous silica nanospheres (HMSNs/Au) was prepared by a one-pot sol-gel method, in which gold ions were loaded in hollow mesoporous silica spheres followed by sodium alginate reduction. The characterization of the HMSNs/Au were determined by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), N₂ adsorption–desorption isotherms (BET). The high catalytic activity of HMSNs/Au, denoted as apparent turn-over frequency (TOF), was detected by UV-Vis spectrophotometer for the catalytic reduction of 4-nitrophenol (74.5 h^?1) and 2-nitrophenol (108.7 h^?1) in the presence of sodium borohydride solution due to the small gold nanoparticles size and overall exposure of active sites. It is expected that this ecofriendly approach to prepare inorganic composited nanoparticles as high active catalysts based on hollow mesoporous materials was a promising platform for loading noble metal nanoparticles.