稀土氧化物纳米粒子调制聚合物分散液晶电光特性的研究

通过对聚合物分散液晶(PDLC)掺杂稀土氧化物纳米粒子Gd2O3,Eu2O3和Nd2O3,测试可见光范围内PDLC掺杂前后的透射率随驱动电压的变化,进而研究稀土氧化物对PDLC电光特性的调制作用。实验结果表明:掺杂Gd2O3的PDLC样品透射率在驱动电压低于10V时,随驱动电压升高而降低,当驱动电压达到为15V时,样品对光感应出现了弛豫现象,使得其透射率围绕10V时的透射率做微小的上下波动,当驱动电压达到20V时,样品透射率迅速升高,并出现了滤光现象;掺杂Eu2O3的PDLC样品透射率随驱动电压升高而下降,下降的幅度较小;掺杂Nd2O3的PDLC样品透射率随驱动电压的变化不明显。     

TiO2纳米颗粒对染料掺杂聚合物分散液晶的随机激光辐射特性的影响

随机激光的阈值与体系内的散射强度存在密切关系.高折射率二氧化钛(TiO2)纳米颗粒与染料掺杂聚合物分散液晶(DDPDLC)均匀混合后,由于液晶微滴与TiO2纳米颗粒之间的强散射作用,DDPPLC的随机激光具有更低的激光发射阈值,并且随TiO2纳米颗粒的掺杂浓度而变化;在优化TiO2纳米颗粒掺杂浓度的基础上,DDPDLC...     

Lu2O3：Tb纳米粉末的光致发光特性

用燃烧合成法制备了Lu₂O₃:Tb³⁺纳米粉末。产物为立方相结构,粒径在3~40nm之间可控。对不同颗粒度的样品的激发光谱、发射光谱和荧光衰减特性进行了研究。在紫外光激发下,样品显示出较强的发光(来自于Tb³⁺的⁵D_3,4→⁷F_J跃迁)。同时,样品的光致发光性质在很大程度上受到样品颗粒度的影响,对此现象给出了合理的解释。     

MoO3/Al2O3催化剂中Mo分散的正电子研究

用浸渍法制备了一系列不同Mo含量的MoO₃/Al₂O₃催化剂.测量了这些样品的正电子湮没寿命谱(PALS)与符合多普勒展宽(CDB)谱,以研究其孔洞结构以及Mo分散.正电子寿命测量结果表明,Al₂O₃载体中存在两种不同尺寸的孔洞.掺入MoO₃之后,Mo原子主要进入Al₂O₃的大孔中,使孔洞体积减小.符合多普勒展宽谱结果表明,当MoO 关键词： 3/Al₂O₃催化剂')" href="#">MoO₃/Al₂O₃催化剂 正电子湮没寿命谱 符合多普勒展宽 Mo 分散     

Fe3O4纳米粒子对P3HT:PCBM电池的影响

为了提高太阳能电池的性能,研究磁性纳米粒子在外加磁场的作用下对聚合物太阳能电池有源层P3HT:PCBM成膜及太阳能电池性能的影响。本文采用热分解法制备了磁性Fe₃O₄纳米粒子,将不同质量分数的Fe₃O₄纳米粒子掺入到P3HT:PCBM溶液中,旋涂后在外加磁场的作用下自组成膜。通过TEM、XRD对制备的Fe₃O₄纳米粒子进行表征,并利用偏光显微镜、原子力显微镜对成膜质量进行探究。结果表明,采用热分解法制备的Fe₃O₄纳米粒子直径在10 nm左右,在外加磁场作用下,Fe₃O₄纳米粒子对成膜有一定的调控作用。当Fe₃O₄纳米粒子掺杂质量分数为1%时,太阳能电池器件的开路电压增加3.77%,短路电流增加24.93%,光电转换效率提高7.82%。     

Li+离子掺杂Gd2O3：Sm3+纳米晶的发光增强

采用燃烧法制备了Gd₂O₃:Sm³⁺和Li⁺离子掺杂的Gd₂O₃:Sm³⁺纳米晶,根据X射线衍射图谱确定所得纳米样品为纯立方相。在室温下,用275 nm和980 nm激发光激发各样品时,可分别观测到Sm³⁺离子的强荧光发射和上转换特征发射,其主发射峰分别位于560,602,650 nm处,分别对应着Sm³⁺离子的⁴G_5/2→⁶H_5/2,⁴G_5/2→⁶H_7/2和⁴G_5/2→⁶H_9/2的电子跃迁,其中以⁴G_5/2→⁶H_7/2跃迁的光谱强度最大。实验表明Li⁺离子的掺入使得Sm³⁺离子的荧光发射强度显著增加。通过对样品的XRD、TEM和激发光谱、发射光谱的研究,分析了引起样品荧光强度变化的原因。     

前驱体和退火温度对Nd2O3薄膜组分影响的定量研究

采用Nd(thd)₃和O₃作为反应前驱体, 利用先进的原子层淀积方法在P型硅(100)衬底上制备了超薄Nd₂O₃介质膜, 并在N₂气氛下进行了退火处理. 采用X射线光电子能谱仪对薄膜样品组分进行分析. 研究结果表明, 淀积过程中将前驱体温度从175 ℃提高到185 ℃后, 薄膜的质量得到提高, O/Nd 原子比达到1.82, 更接近理想的化学计量比, 介电常数也从6.85升高到10.32.     

Y2O3:Eu纳米晶中能量传递相互作用的研究

通过浓度猝灭曲线确定了引起Y₂O₃纳米晶中Eu³⁺发光浓度猝灭的是交换相互作用.测量了两种颗粒尺寸下Eu³⁺的⁵D₀—⁷F₂跃迁发光衰减曲线随掺杂浓度的变化,利用交换相互作用的理论衰减曲线对实验衰减曲线进行拟合.计算Eu³⁺离子的交换相互作用能量传递的效率,分析了Y₂O_{3关键词： 能量传递 2}O₃Eu纳米晶')" href="#">Y₂O₃Eu纳米晶 发光衰减     

Na+离子掺杂Gd2O3 ∶ Sm3+纳米晶的发光增强

采用柠檬酸作燃烧剂,在柠檬酸-硝酸盐体系下制备了Gd₂O₃ ∶ Sm³⁺和Gd₂O₃ ∶ Sm³⁺,Na⁺纳米晶。用X射线衍射仪、透射电子显微镜、荧光光谱仪等对样品的结构、形貌和光致发光性能进行了分析。结果表明:所得纳米样品为纯立方相,晶粒尺寸约为30 nm。在室温下,用275 nm激发光激发各样品时,可观测到Sm³⁺离子 的较强发光,其主发射峰位分别位于561.5,603.5,651.5 nm,分别对应着Sm³⁺离子的⁴G_5/2→⁶H_5/2 , ⁴G_5/2→ ⁶H_7/2 和⁴G_5/2 →⁶H_9/2的电子跃迁, 其中以⁴G_5/2→⁶H_7/2 跃迁的光谱强度最强。实验表明:Na⁺离子的掺入使得Sm³⁺离子的光发射强度显著增强。对引起样品荧光强度变化的原因进行了分析。     

α-Al2O3(0001)基片表面结构与能量研究

对α-Al₂O₃(0001)晶体表层三种不同终止原子结构的计算模型， 在三维周期边界条件下 的κ空间中，采用超软赝势平面波函数描述多电子体系.应用基于密度泛函理论的局域密度 近似，计算了不同表层结构的体系能量，表明最表层终止原子为单层Al的表面结构最稳定. 对由10个原子组成的菱形原胞进行了结构优化，得到晶胞参数值(a₀＝0.48178n m)与实验 报道值误差小于1.3%.进一步计算了超晶胞(2×2)表面弛豫，弛豫后原第2层O原子层成为最 表层； 对不同表层O，Al原子最外层电子进行了布居分析，表面电子有更大的概率被定域在 O原子的周围，表面明显地表现出O原子的电子表面态. 关键词： 2O₃(0001)')" href="#">α-Al₂O₃(0001) 超软赝势 表面结构 表面态     

基于Al_2O_3/MoO_3复合阳极缓冲层的倒置聚合物太阳能电池的研究

采用旋涂Al_2O_3前驱体溶液和低温退火的方法在活性层上形成Al_2O_3薄膜,并与MoO_3结合形成Al_2O_3/MoO_3复合阳极缓冲层,制备了以聚3-己基噻吩:[6.6]-苯基-C_(61)-丁酸甲酯(P3HT:PC_(61)BM)为活性层的倒置聚合物太阳能电池,并通过改变Al_2O_3前驱体溶液的浓度来分析复合阳极缓冲层对器件性能的影响.结果发现,Al_2O_3/MoO_3复合阳极缓冲层能有效调控倒置聚合物太阳能电池的光电性能及其稳定性.当Al_2O_3前驱体溶液的浓度为0.15%时,器件光伏性能达到最优值,与MoO_3单缓冲层的器件相比,光电转换效率(PCE)由3.85%提高到4.64%;经过80天老化测试后,具有复合阳极缓冲层的器件PCE保留为初始值的76%,而单缓冲层的器件PCE已经下降到50%以下.器件性能得到改善的原因是Al_2O_3/MoO_3复合阳极缓冲层增强了倒置太阳能电池器件阳极对空穴的收集能力,同时钝化了器件活性层,从而提升了太阳能电池器件的光伏性能及其稳定性.     

高浓度Er~(3+)掺杂Y_3Sc_2Ga_3O_(12)晶体的吸收光谱与晶体场模型研究

采用提拉法生长出了高浓度掺铒(35 at%)钇钪镓石榴石(Er:YSGG)激光晶体.测试了该晶体在340—1700 nm波段内的吸收光谱,对其中Er3+的实验能级进行了分析指认.用Er:YSGG的102个实验Stark能级,拟合了它的自由离子参数和晶体场参数,均方根误差(拟合精度)σ为10.34 cm-1.结果表明,参数化Stark能级的拟合结果与实验光谱符合得较好.将拟合得到的Er:YSGG实验结果与文献中已报道Er:YAG的自由离子参数和晶体场参数进行了比较.指出Er:YSGG具有较强的晶体场相互作用或许是其激光效率较高的主要原因之一.     

Luminescence studies on ZnO-P2O5 glasses doped with Gd2O3:Eu nanoparticles and Eu2O3

Zinc phosphate glasses doped with Gd₂O₃:Eu nanoparticles and Eu₂O₃ were prepared by conventional melt-quench method and characterized for their luminescence properties. Binary ZnO-P₂O₅ glass is characterized by an intrinsic defect centre emission around 324 nm. Strong energy transfer from these defect centres to Eu³⁺ ions has been observed when Eu₂O₃ is incorporated in ZnO-P₂O₅ glasses. Lack of energy transfer from these defect centres to Eu³⁺ in Gd₂O₃:Eu nanoparticles doped ZnO-P₂O₅ glass has been attributed to effective shielding of Eu³⁺ ions from the luminescence centre by Gd-O-P type of linkages, leading to an increased distance between the luminescent centre and Eu³⁺ ions. Both doped and undoped glasses have the same glass transition temperature, suggesting that the phosphate network is not significantly affected by the Gd₂O₃:Eu nanoparticles or Eu₂O₃ incorporation.     

Structure and optical properties of sol–gel derived Gd2O3 waveguide films

Pure and rare earth doped gadolinium oxide (Gd₂O₃) waveguide films were prepared by a simple sol–gel process and dip-coating method. Gd₂O₃ was successfully synthesized by hydrolysis of gadolinium acetate. Thermogravimetric analysis (TGA) and differential thermal analysis (DTA) were used to study the thermal chemistry properties of dried gel. Structure of Gd₂O₃ films annealed at different temperature ranging from 400 to 750 °C were investigated by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD) and transmission electron microscopy (TEM). The results show that Gd₂O₃ starts crystallizing at about 400 °C and the crystallite size increases with annealing temperature. Oriented growth of (4 0 0) face of Gd₂O₃ has been observed when the films were deposited on (1 0 0) Si substrate and annealed at 750 °C. The laser beam (λ=632.8 nm) was coupled into the film by a prism coupler and propagation loss of the film measured by scattering-detection method is about 2 dB/cm. Luminescence properties of europium ions doped films were measured and are discussed.     

Optical properties of (ZnO)0.5(P2O5)0.5 glasses doped with Gd2O3:Eu nanoparticles and Eu2O3

Binary (ZnO)_0.5(P₂O₅)_0.5 glasses doped with Eu₂O₃ and nanoparticles of Gd₂O₃:Eu were prepared by conventional melt-quench method and their luminescence properties were compared. Undoped (ZnO)_0.5(P₂O₅)_0.5 glass is characterized by a luminescent defect centre (similar to L-centre present in Na₂O-SiO₂ glasses) with emission around 324 nm and having an excited state lifetime of 18 ns. Such defect centres can transfer the energy to Eu³⁺ ions leading to improved Eu³⁺ luminescence from such glasses. Based on the decay curves corresponding to the ⁵D₀ level of Eu³⁺ ions in both Gd₂O₃:Eu nanoparticles incorporated as well as Eu₂O₃ incorporated glasses, a significant clustering of Eu³⁺ ions taking place with the latter sample is confirmed. From the lifetime studies of the excited state of L-centre emission from (ZnO)_0.5(P₂O₅)_0.5 glass doped with Gd₂O₃:Eu nanoparticles, it is established that there exists weak energy transfer from L-centres to Eu³⁺ ions. Poor energy transfer from the defect centres to Eu³⁺ ions in Gd₂O₃:Eu nanoparticles doped (ZnO)_0.5(P₂O₅)_0.5 glass has been attributed to effective shielding of Eu³⁺ ions from the luminescence centre by Gd-O-P type of linkages, leading to an increased distance between luminescent centre and Eu³⁺ ions.     

熔融织构YBa2Cu3O7-δ晶体中磁通涡旋锁定转变反常行为研究

通过改变磁场与c轴方向夹角测量了熔融织构YBa₂Cu₃O_7-δ (YBCO)晶体的磁力矩信号响应, 观察到了磁通涡旋系统的锁定(lock-in)转变行为以及锁定转变角正比于外磁场强度的反常现象. 基于Ginzburg-Landau理论和磁通涡旋线Kink结构模型, 对上述锁定转变反常现象进行了分析讨论, 提出了熔融织构YBCO晶体中存在平行于a-b面的延展性关联缺陷结构假设, 导出了锁定转变临界角与温度和磁场之间的关系, 理论分析模型结果与实验测量结果基本符合.     

石墨烯在Al_2O_3(0001)表面生长的模拟研究

基于密度泛函理论的广义梯度近似法,对用化学气相沉积法在蓝宝石(α-Al_2O_3)(0001)表面上生长石墨烯进行理论研究.研究结果表明:CH_4在α-Al_2O_3(0001)表面上的分解是吸热过程,由CH_4完全分解出C需要较高能量及反应能垒,这些因素不利于C在衬底表面的存在.在α-Al_2O_3(0001)表面,石墨烯形核的活跃因子并不是通常认为的C原子,而是CH基团.通过CH基团在α-Al_2O_3(0001)表面上的迁移聚集首先形成能量较低的(CH)_x结构.模拟研究(CH)_x对揭示后续石墨烯的形核生长机理具有重要意义.     

掺杂Y2O3和BaCeO3提高MOD-YBCO超导性能的研究

本文通过在前驱液中添加过量钇盐和铈的有机盐,采用三氟乙酸盐-金属有机沉积法(TFA-MOD) 在铝酸镧单晶基体上制备了含有纳米氧化钇和纳米铈酸钡的YBCO薄膜. 与纯YBCO薄膜相比,掺杂Y₂O₃/BaCeO₃的YBCO膜的临界转变温度几乎保持不变,为91 K左右. 而掺杂Y₂O₃/BaCeO₃的YBCO膜的临界电流密度达到5.0 MA/cm² (77 K, 0T), 是纯YBCO膜临界电流密度的1.5倍.薄膜中的Y₂O₃和BaCeO₃可能在YBCO内部起到了 有效的钉扎磁通作用. 关键词： 钇钡铜氧薄膜 2O₃和纳米BaCeO₃')" href="#">纳米Y₂O₃和纳米BaCeO₃ 磁通钉扎 三氟乙酸盐-金属有机沉积     

Up/down-conversion luminescence of monoclinic Gd2O3:Er3+ nanoparticles prepared by laser ablation in liquid

Multifunctional luminescent materials are attracting attention nowadays. In this work, monoclinic Gd₂O₃:Er³⁺ nanoparticles, which possess up-conversion luminescence and down-conversion luminescence properties, were successfully synthesized by laser ablation in liquid (LAL) technique. Up-conversion luminescence and down-conversion luminescence of monoclinic Gd₂O₃:Er³⁺ nanoparticles were got under the excitation of 980 nm and 379 nm, respectively. In addition, tunable luminescence was got. Furthermore, the cytotoxicity of the nanoparticles is low and the fluorescence of the nanoparticles in cell is also strong enough. The results indicate that the Gd₂O₃:Er³⁺ nanoparticles synthesized by LAL technique are promising candidates for bio-imaging or other fields that require controllable fluorescence.