Influence of surface contaminations on the hydrogen storage behaviour of metal hydride alloys

Hydrogen storage in metal hydrides is a promising alternative to common storage methods. The surface of a metal hydride plays an important part in the absorption of hydrogen, since important partial reaction steps take place here. The development of surface contaminations and their influence on hydrogen absorption is examined by means of absorption experiments and surface analysis, using X-ray photoelectron spectroscopy (XPS), thermal desorption mass spectrometry (TDMS) and secondary neutral mass spectrometry (SNMS), in this work. All investigations were carried out on a modern AB₂ metal hydride alloy, namely Ti_0.96Zr_0.04Mn_1.43V_0.45Fe_0.08. Surface analysis (SNMS, XPS) shows that long-term air storage (several months) leads to oxide layers about 15 nm thick, with complete oxidation of all main alloy components. By means of in situ oxygen exposure at room temperature and XPS analysis, it can be shown that an oxygen dose of about 100 Langmuirs produces an oxide layer comparable to that after air storage. Manganese enrichment (segregation) is also clearly observed and is theoretically described here. This oxide layer hinders hydrogen absorption, so an activation procedure is necessary in order to use the full capacity of the metal hydride. This procedure consists of heating (T = 120° C) in vacuum and hydrogen flushing at pressures like p = 18 bar. During the activation process the alloy is pulverized to particles of ∼20 μm through lattice stretches. It is shown that this pulverization of the metal hydride (creating clean surface) during hydrogen flushing is essential for complete activation of the material. Re-activation of powder contaminated by small doses of air (p ≈ 0.1 bar) does not lead to full absorption capacity. In ultrahigh vacuum, hydrogen is only taken up by the alloy after sputtering of the surface (which is done in order to remove oxide layers from it), thus creating adsorption sites for the hydrogen. This is shown by TDMS measurements with and without sputtering and oxygen exposure. Figure Investigated metal hydride before and after activation     

Some future directions for metal hydride surface studies: Electrons as probes of hydrogen

The current and possible future uses of electrons to detect hydrogen in metal hydride surfaces are reviewed. The available surface techniques, their sensitivity to hydrogen and the effects of electron beam damage are briefly evaluated. To underscore the utility of these “electron-only” techniques to study hydrides, the Auger electron and energy loss spectroscopic results for titanium hydride are given in some detail. As an example of the use of weak electron beam probing methods, tritium imaging, a newly developed technique for the positional detection of tritium, is described. Based on the current limited use of electron beams to probe hydride surfaces on the one hand and the variety of available techniques on the other, a widespread future application of electron beam techniques to study metal hydrides can be expected.     

Using first principles calculations to identify new destabilized metal hydride reactions for reversible hydrogen storage

Hydrides of period 2 and 3 elements are promising candidates for hydrogen storage, but typically have heats of reaction that are too high to be of use for fuel cell vehicles. Recent experimental work has focused on destabilizing metal hydrides through mixing metal hydrides with other compounds. A very large number of possible destabilized metal hydride reaction schemes exist, but the thermodynamic data required to assess the enthalpies of these reactions are not available in many cases. We have used density functional theory calculations to predict the reaction enthalpies for more than 300 destabilization reactions that have not previously been reported. The large majority of these reactions are predicted not to be useful for reversible hydrogen storage, having calculated reaction enthalpies that are either too high or too low, and hence these reactions need not be investigated experimentally. Our calculations also identify multiple promising reactions that have large enough hydrogen storage capacities to be useful in practical applications and have reaction thermodynamics that appear to be suitable for use in fuel cell vehicles and are therefore promising candidates for experimental work.     

The electrochemical performance of AB3-type hydrogen storage alloy as anode material for the nickel metal hydride accumulators

For the purpose of lowering the cost of metal hydride electrode, the La of LaY₂Ni₉ electrode was replaced by Ce. The electrochemical performances of the CeY₂Ni₉ negative electrode, at a room and different temperatures, were compared with the parent alloy LaY₂Ni₉. At room temperature during a long cycling, the evolution of the electrochemical capacity—the diffusivity indicator (\( \frac{D_{\mathrm{H}}}{a^2} \))—the exchange current density, and the equilibrium potential were determined. At different temperatures, the electrochemical characterization of this alloy allowed the estimation of the enthalpy, the entropy, and the activation energy of the hydride formation. The evolution of the high-rate dischargeability was also evaluated at different temperatures. Compared with the parent LaY₂Ni₉ alloy, CeY₂Ni₉ exhibits an easy activation and good reaction reversibility. This alloy also conserves a good lifetime during a long-term cycling. A lower activation energy determined for this alloy corresponds to an easy absorption of hydrogen into this new alloy.     

Alkali and alkaline-earth metal amidoboranes: structure, crystal chemistry, and hydrogen storage properties

Alkali- and alkaline-earth metal amidoboranes are a new class of compounds with rarely observed [NH2BH3](-) units. LiNH2BH3 and solvent-containing Ca(NH2BH3)2 x THF have been recently reported to significantly improve the dehydrogenation properties of ammonia borane. Therefore, metal amidoboranes, with accelerated desorption kinetics and suppressed toxic borazine, are of great interest for their potential applications for hydrogen storage. In this work, we successfully determined the structures of LiNH2BH3 and Ca(NH2BH3)2 using a combined X-ray diffraction and first-principles molecular dynamics simulated annealing method. Through detailed structural analysis and first-principles electronic structure calculations the improved dehydrogenation properties are attributed to the different bonding nature and reactivity of the metal amidoboranes compared to NH3BH3.     

Some structural systematics in metal carbonyl cluster chemistry

The recently developed electron-counting rules for condensed polyhedral metal carbonyl clusters have been utilised to develop a systematic approach for enumerating the structural alternatives for metal cluster compounds which are isoelectronic. The more usual cluster degradation and aggregation processes are represented in a matrix form which relates the change in electron count to the number of new bonds formed (or broken). The matrices for cluster degradation and aggregation are represented in a complementary fashion so that the search for isoelectronic clusters greatly simplified. The utility of the approach is illustrated by reference to some recent examples from metal carbonyl cluster chemistry.     

Role of exposed metal sites in hydrogen storage in MOFs

The role of exposed metal sites in increasing the H2 storage performances in metal-organic frameworks (MOFs) has been investigated by means of IR spectrometry. Three MOFs have been considered: MOF-5, with unexposed metal sites, and HKUST-1 and CPO-27-Ni, with exposed Cu(2+) and Ni(2+), respectively. The onset temperature of spectroscopic features associated with adsorbed H2 correlates with the adsorption enthalpy obtained by the VTIR method and with the shift experienced by the H-H stretching frequency. This relationship can be ascribed to the different nature and accessibility of the metal sites. On the basis of a pure energetic evaluation, it was observed that the best performance was shown by CPO-27-Ni that exhibits also an initial adsorption enthalpy of -13.5 kJ mol(-1), the highest yet observed for a MOF. Unfortunately, upon comparison of the hydrogen amounts stored at high pressure, the hydrogen capacities in these conditions are mostly dependent on the surface area and total pore volume of the material. This means that if control of MOF surface area can benefit the total stored amounts, only the presence of a great number of strong adsorption sites can make the (P, T) storage conditions more economically favorable. These observations lead to the prediction that efficient H2 storage by physisorption can be obtained by increasing the surface density of strong adsorption sites.     

Surface chemistry of quantum-sized metal nanoparticles under light illumination

Size reduction of metal nanoparticles increases the exposure of metal surfaces significantly, favoring heterogeneous chemistry at the surface of the nanoparticles. The optical properties of metal nanoparticles, such as light absorption, also exhibit a strong dependence on their size. It is expected that there will be strong coupling of light absorption and surface chemistry when the metal nanoparticles are small enough. For instance, metal nanoparticles with sizes in the range of 2–10 nm exhibit both surface plasmon resonances, which can efficiently produce high-energy hot electrons near the surface of the nanoparticles under light illumination, and the Coulomb blockade effect, which favors electron transfer from the metal nanoparticles to the surface adsorbates. The synergy of efficient hot electron generation and electron transfer on the surface of small metal nanoparticles leads to double-faced effects: (i) surface (adsorption) chemistry influences optical absorption in the metal nanoparticles, and (ii) optical absorption in the metal nanoparticles promotes (or inhibits) surface adsorption and heterogeneous chemistry. This review article focuses on the discussion of typical quantum phenomena in metal nanoparticles of 2–10 nm in size, which are referred to as “quantum-sized metal nanoparticles”. Both theoretical and experimental examples and results are summarized to highlight the strong correlations between the optical absorption and surface chemistry for quantum-sized metal nanoparticles of various compositions. A comprehensive understanding of these correlations may shed light on achieving high-efficiency photocatalysis and photonics.

Size reduction of metal nanoparticles increases the exposure of metal surfaces significantly, favoring heterogeneous photochemistry at the surface of the nanoparticles.     

Temporal and spatial imaging of hydrogen storage materials: watching solvent and hydrogen desorption from aluminium hydride by transmission electron microscopy

An in situ thermal desorption study of solvated aluminum hydride (alane) by transmission electron microscopy and selected area diffraction has permitted characterisation of the structural and morphological changes during desorption of solvent and hydrogen in real-time; this powerful technique for studying hydrogen storage materials complements several others already employed.     

Tuning metal hydride thermodynamics via size and composition: Li-H, Mg-H, Al-H, and Mg-Al-H nanoclusters for hydrogen storage

Nanoscale Li and intermetallic Al-Mg metal hydride clusters are investigated as a possible hydrogen storage material using the high-level quantum Monte Carlo computational method. Lower level methods such as density functional theory are qualitatively, not quantitatively accurate for the calculation of the enthalpy of absorption of H(2). At sizes around 1 nm, it is predicted that Al/Mg alloyed nanoparticles are stable relative to the pure compositions and the metal composition can be tuned in tandem with the size to tune the hydrogen absorption energy, making this a promising route to a rechargeable hydrogen storage material.     

Destabilisation of magnesium hydride by germanium as a new potential multicomponent hydrogen storage system

MgH(2) has too high an operating temperature for many hydrogen storage applications. However, MgH(2) ball-milled with Ge leads to a thermodynamic destabilisation of >50 kJ mol(-1)(H(2)). This has dramatically reduced the temperature of dehydrogenation to 130 °C, opening up the potential for Mg-based multicomponent systems as hydrogen stores for a range of applications.     

Indirect, reversible high-density hydrogen storage in compact metal ammine salts

The indirect hydrogen storage capabilities of Mg(NH 3) 6Cl 2, Ca(NH 3) 8Cl 2, Mn(NH 3) 6Cl 2, and Ni(NH 3) 6Cl 2 are investigated. All four metal ammine chlorides can be compacted to solid tablets with densities of at least 95% of the crystal density. This gives very high indirect hydrogen densities both gravimetrically and volumetrically. Upon heating, NH 3 is released from the salts, and by employing an appropriate catalyst, H 2 can be released corresponding to up to 9.78 wt % H and 0.116 kg H/L for the Ca(NH 3) 8Cl 2 salt. The NH 3 release from all four salts is investigated using temperature-programmed desorption employing different heating rates. The desorption is found mainly to be limited by heat transfer, indicating that the desorption kinetics are extremely fast for all steps. During desorption from solid tablets of Mg(NH 3) 6Cl 2, Mn(NH 3) 6Cl 2, and Ni(NH 3) 6Cl 2, nanoporous structures develop, which facilitates desorption from the interior of large, compact tablets. Density functional theory calculations reproduce trends in desorption enthalpies for the systems studied, and a mechanism in which individual chains of the ammines are released from the surface of the crystal is proposed to explain the fast absorption/desorption processes.     

Some general aspects of hydrogen chemisorption on metal surfaces

Chemisorption of hydrogen on metal surfaces requires the dissociation of the H₂ molecule in the first place; this process has been experimentally investigated and theoretically described in terms of multi-dimensional potential energy diagrams. The adsorption of atomic hydrogen is frequently accompanied by displacements of the metal surface atoms leading to phenomena such as layer relaxation or surface reconstruction. Especially surface reconstruction may be regarded as a precursor stage for a progressive chemical attack of the hydrogen atoms also on the bulk metal, leading to the occupation of so-called “subsurface” sites, to bulk diffusion and, finally, to hydride compound formation. All these processes depend sensitively on the crystallographic structure of the surface, and some examples for H on Rh, Co and Pd surfaces will demonstrate the general correlation between the hydrogen surface concentration and the metal's cohesive energy, surface crystallography, and its tendency to reconstruct.     

Investigation of corannulene for molecular hydrogen storage via computational chemistry and experimentation

Molecular simulations for hydrogen physisorption with corannulene molecules arranged according to their crystal structure result in good agreement with the weight-percent hydrogen stored as determined experimentally employing a 3-g sample of highly crystalline corannulene at ambient temperatures and 72 bar of pressure. Calculated enthalpies of adsorption for corannulene/hydrogen molecular systems obtained from ab initio calculations which take into account electron correlation via second-order M?ller-Plesset perturbation theory are in good agreement with literature experimental enthalpies of adsorption for activated carbons interacting with molecular hydrogen. Ab initio results also show that corannulene molecules arranged in a sandwich structure are important for approximately doubling the binding energy of corannulene interacting with molecular hydrogen through a cooperative interaction. To test the effects of finite temperatures and pressures, stack arrays were used as input for molecular dynamics simulations and indicate that physisorption mechanisms including van der Waals forces and dipole-induced dipole interactions may yield enhanced adsorption capacity in relation to other carbon-based materials. These results will be instrumental in identifying interlayer separations of an array of corannulene or related molecules that may provide a high weight percent of physisorbed hydrogen.     

A first-principles study of the electronic structure and stability of a lithium aluminum hydride for hydrogen storage

LiAlH4 holds great promise for reversible hydrogen storage, where a fundamental understanding of hydrogen interaction with the metal elements is essential to further improve its properties. The present paper reports a first-principles study of its stability and electronic structure, using a full potential linearized augmented plane wave (FLAPW) method within the generalized gradient approximation (GGA) for high accuracy. The theoretically calculated heat of formation agrees well with experiment. The electronic structures show that the H atoms bond nonequivalently with the Al in the [AlH4]- ligand, which leads to complex dehydrogenation characteristics of LiAlH4.