高倍率尖晶石型Li4Ti5O12/TiN锂离子电池负极材料的合成及其电化学性能

以乙酰丙酮(ACAC)螯合剂、聚乙二醇(PEG)为分散剂,采用溶胶-凝胶法合成了尖晶石型Li4Ti5O12/TiN材料.考察了TiN膜对尖晶石型Li4Ti5O12锂离子电池负极材料电化学性能的影响.利用X射线光电子能谱(XPS)对Li4Ti5O12表面的TiN膜进行了分析.X射线衍射(XRD)和扫描电子显微镜(SEM)分析表明,Li4Ti5O12/TiN材料为结晶良好的亚微米纯相尖晶石型钛酸锂.电化学性能测试表明,该材料的首次放电比容量为173.0mAh·g-1,并且具有良好的循环性能,以0.2C、1C、2C、5C倍率放电进行测试,10次循环后比容量分别为170.6、147.6、135.6、111.0 mAh·g-1,较之表面无TiN膜的钛酸锂材料表现出更好的倍率特性.循环伏安曲线(CV),交流阻抗图谱(EIS)进一步论证了TiN膜改善了尖晶石型Li4Ti5O12锂离子电池负极材料的电化学性能.     

高倍率尖晶石型Li_4Ti_5O_(l2)/TiN锂离子电池负极材料的合成及其电化学性能

以乙酰丙酮(ACAC)为螯合剂、聚乙二醇(PEG)为分散剂,采用溶胶-凝胶法合成了尖晶石型Li4Ti5Ol2/TiN材料.考察了TiN膜对尖晶石型Li4Ti5Ol2锂离子电池负极材料电化学性能的影响.利用X射线光电子能谱(XPS)对Li4Ti5O12表面的TiN膜进行了分析.X射线衍射(XRD)和扫描电子显微镜(SEM)分析表明,Li4Ti5Ol2/TiN材料为结晶良好的亚微米纯相尖晶石型钛酸锂.电化学性能测试表明,该材料的首次放电比容量为173.0mAh·g-1,并且具有良好的循环性能,以0.2C、1C、2C、5C倍率放电进行测试,10次循环后比容量分别为170.6、147.6、135.6、111.0mAh·g-1,较之表面无TiN膜的钛酸锂材料表现出更好的倍率特性.循环伏安曲线(CV),交流阻抗图谱(EIS)进一步论证了TiN膜改善了尖晶石型Li4Ti5Ol2锂离子电池负极材料的电化学性能.     

锂离子电池负极材料Li4Ti5O12的半固相法制备及碳包覆改性

由半固相法制得锂离子电池负极材料Li4Ti5O12,并研究了Li4Ti5O12的碳包覆改性.采用XRD、SEM、TEM以及HRTEM观察和分析产物的相结构与形貌.采用恒流充放电、循环伏安法和交流阻抗技术测试了材料的电化学性质.结果表明,Li4Ti5O12因颗粒团聚电化学性能严重下降,该电极在0.1C和0.5C首周期放电容量分别为121.7和87.6 mAh·g-1;碳包覆Li4Ti5O12/C材料呈球形分布,能抑制颗粒团聚,该电极倍率<0.5C时的放电比容量大于180 mAh·g-1,超过Li4Ti5O12的理论放电比容量(175 mAh·g-1);在1C、5C和10C倍率下,其容量仍保持在136、79.9和58.3 mAh·g-1,碳包覆改性材料具有优异的循环寿命和高倍率性能.     

锂钛复合氧化物锂离子电池负极材料的研究

采用 3种化学方法合成锂钛复合氧化物 .应用X -射线衍射分析对其结构进行表征以及电化学性能测试 ,结果表明 :由Li2 CO3、TiO2 高温合成的锂钛复合氧化物为尖晶石结构的Li4Ti5 O12 .Li4Ti5 O12 电极在 1 .5V左右有一放电平台 ,充放电可逆性良好 ,即充电电压平台与此接近 ,且电极的比容量较大 ,循环性能良好 .以 0 .30mA·cm- 2 充放电时 ,首次放电容量可达 30 0mAh·g- 1,可逆比容量为 1 0 0mAh·g- 1,经多次充放电循环后 ,其结构仍保持稳定性 .试验电池测试表明 ,Li4Ti5 O12 可选作Li4Ti5 O12 /LiCoO2 锂离子电池的负极材料 .     

三维连续结构Li4Ti5O12/石墨烯纳米复合材料：制备和其锂离子电池超长循环性能

利用具有三维连续纳米孔结构的热剥离石墨烯为骨架制备Li4Ti5O12/石墨烯纳米复合材料。通过乙醇挥发法在热剥离石墨烯的纳米孔道内引入前驱物,进一步高温热处理,在热剥离石墨烯的孔道内原位形成Li4Ti5O12纳米粒子。利用复合材料作为锂离子电池电极材料。电化学反应过程中,热剥离石墨烯的三维连续结构确保了Li4Ti5O12纳米粒子与石墨烯在长循环过程中的有效接触。因此,复合材料表现出优异的循环稳定性。在5C下,5 000次循环后,其容量保持率高达94%。     

Li_4Ti_5O_(12)亚微米球的制备及其在锂离子电池中的应用

主要合成了具有尖晶石结构的Li4Ti5O12亚微米球电极材料,并研究了其作为锂离子电池负极材料的电化学性能.材料的制备分为三个步骤:TiCl4水解得到金红石相的TiO2,然后将得到的TiO2与LiOH进行水热反应得到中间相LiTi2O4+δ,最后将中间相高温煅烧得到尖晶石结构的Li4Ti5O12.采用XRD、SEM和TEM等手段对材料的结构和形貌进行表征.结果表明,尖晶石相的Li4Ti5O12负极材料具有分级结构,是由20～30nm的小颗粒堆积成约为200～300nm的亚微米球.将制备的Li4Ti5O12材料进行恒电流充放电测试表明,材料具有优异的倍率放电性能和较好的循环可逆性;在1C充放电时,首次放电比容量达到174.3mAh/g,在第5～50次循环过程中仅有微小的不可逆容量损失.采用循环伏安法测得Li+的扩散系数为1.03×10-7cm2/s.研究表明合成的Li4Ti5O12亚微米球在高效可充电锂离子电池中具有良好的应用前景.     

晶态Li_4Ti_5O_(12)负极材料的制备及其与电解液的兼容性研究

本文以醋酸锂和钛酸丁酯为原料,以冰醋酸为抑制剂,采用溶胶-凝胶法制备了晶态Li4Ti5O12负极材料。与自制的3种电解液和实验室常用的电解液分别组装成锂/钛酸锂半电池。采用恒流充放电测试、循环伏安法(CV)及交流阻抗法(EIS)对其电化学性能进行研究。研究结果发现:在以环状碳酸酯类(EC、PC)和线性碳酸酯类(MEC)为溶剂、以六氟磷酸锂(LiPF6)为电解质的电解液中添加双乙二酸硼酸锂(LiBOB),有利于提高半电池的性能,首次放电比电容达到了198mA.h.g-1,且放电比电容经多次充放电后衰减得较小。而在电解液中加入碳酸亚乙烯酯(VC),半电池的性能有所下降。Li4Ti5O12对电解液表现出较明显的兼容性。     

LiTi2O4用作锂离子电池负极的研究进展

LiTi2O4具有长的嵌锂反应循环寿命、较低的电位和良好的导电性,是继碳素材料和Li4Ti5O12之后的又一新型锂离子电池负极材料,有望在大电流和动力锂离子电池中得到较大的应用.本文介绍了LiTi2O4负极材料的晶体结构、物理特性、制备方法、电化学性能及其应用研究进展,并分析了其微观导电机理.     

锂离子电池负极材料Li4Ti5O12

Li4Ti5O12具有充放电循环性能好、电压平台平稳、安全性高、价格低、环境友好、易于制备等优点,在锂离子电池负极材料中得到广泛研究.本文基于国内外近期的研究进展,综述了制备Li4Ti5O12的方法,着重介绍了固相、溶胶一凝胶、熔盐、燃烧、喷雾、水/溶剂热等几种主要的合成方法,并针对Li4Ti5O12电导率低的缺点,详...     

锂离子电池负极材料Li_(4-x)K_xTi_5O_(12)结构和电化学性能

采用固相反应的方法制备了尖晶石型Li4Ti5O12和K掺杂Li4-xKxTi5O12(x=0.02,0.04,0.06)。通过XRD、SEM、BET等对制备材料进行了分析。结果表明,K掺杂没有影响立方尖晶石型Li4Ti5O12的合成,同时也没有改变Li4Ti5O12的电化学反应过程。K掺杂Li4-xKxTi5O12具有比Li4Ti5O12小的颗粒粒径和比Li4Ti5O12大的比表面积、孔容积。适量的K掺杂能够明显改善Li4Ti5O12的电化学性能,尤其是倍率性能,但是过多的K掺杂却不利于材料电化学性能的提高。研究表明,Li3.96K0.04Ti5O12体现了相对较好的倍率性能和循环稳定性。0.5C下,首次放电比容量为161mAh·g-1,3.0和5.0C下,容量保持分别为138和121mAh·g-1。3.0C下,200次循环后容量保持为137mAh·g-1。     

Study of Surface Reaction of Spinel Li(4)Ti(5)O(12) during the First Lithium Insertion and Extraction Processes Using Atomic Force Microscopy and Analytical Transmission Electron Microscopy

Spinel lithium titanate (Li(4)Ti(5)O(12), LTO) is a promising anode material for a lithium ion battery because of its excellent properties such as high rate charge-discharge capability and life cycle stability, which were understood from the viewpoint of bulk properties such as small lattice volume changes by lithium insertion. However, the detailed surface reaction of lithium insertion and extraction has not yet been studied despite its importance to understand the mechanism of an electrochemical reaction. In this paper, we apply both atomic force microscopy (AFM) and transmission electron microscopy (TEM) to investigate the changes in the atomic and electronic structures of the Li(4)Ti(5)O(12) surface during the charge-discharged (lithium insertion and extraction) processes. The AFM observation revealed that irreversible structural changes of an atomically flat Li(4)Ti(5)O(12) surface occurs at the early stage of the first lithium insertion process, which induces the reduction of charge transfer resistance at the electrolyte/Li(4)Ti(5)O(12) interface. The TEM observation clarified that cubic rock-salt crystal layers with a half lattice size of the original spinel structure are epitaxially formed after the first charge-discharge cycle. Electron energy loss spectroscopy (EELS) observation revealed that the formed surface layer should be α-Li(2)TiO(3). Although the transformation of Li(4)Ti(5)O(12) to Li(7)Ti(5)O(12) is well-known as the lithium insertion reaction of the bulk phase, the generation of surface product layers should be inevitable in real charge-discharge processes and may play an effective role in the stable electrode performance as a solid-electrolyte interphase (SEI).     

LiV3O8在Li2SO4水溶液中的电化学性能

采用低温固相法合成了具有纳米结构的LiV₃O₈材料.扫描电子显微镜（SEM）及透射电子显微镜（TEM）测试显示该材料具有纳米结构.X射线衍射（XRD）表明该材料属于单斜晶系,P2₁Im空间群.并采用循环伏安法（CV）及电化学阻抗谱图测试对该材料在1、2 mol·L^-1Li₂SO₄水溶液及饱和Li₂SO₄水溶液中的电化学行为进行了研究.结果表明,LiV₃O₈在饱和Li₂SO₄水溶液中具有最好的电化学性能.以LiV₃O₈作为负极材料,LiNi_1/3Co_1/3Mn_1/3O₂作为正极材料,饱和Li₂SO₄水溶液作为电解液组成了水性锂离子电池,进行恒流充放电测试,结果表明,在0.5C(1C=300 mA·g^-1)的充放电倍率下,该水性锂离子电池的首次放电比容量为95.2 mAh·g^-1,循环100次后仍具有37.0 mAh·g^-1的放电比容量.     

锂离子电池新型快充负极材料Li4Ti5O12的改性研究

采用传统固相法制备尖晶石型Li4Ti5O12, 在前驱物中掺杂聚合物裂解碳材料聚并苯(PAS). 经四探针测试仪测量, 电导率提高9个数量级. 复合物的电化学性能测试结果表明, 其循环性和高倍率性能得到了明显改善.     

Ultraslow Li diffusion in spinel-type structured Li4Ti5O12 - a comparison of results from solid state NMR and impedance spectroscopy

The cubic spinel oxides Li(1+x)Ti(2-x)O(4) (0 < or =x< or = 1/3) are promising anode materials for lithium-ion rechargeable batteries. The end member of the Li-Ti-O series, Li(4)Ti(5)O(12), can accommodate Li ions up to the composition Li(7)Ti(5)O(12). Whereas a number of studies focus on the electrochemical behaviour of Li insertion into and Li diffusion in the Li intercalated material, only few investigations about low-temperature Li dynamics in the non-intercalated host material Li(4)Ti(5)O(12) have been reported so far. In the present paper, Li diffusion in pure-phase microcrystalline Li(4)Ti(5)O(12) with an average particle size in the microm range was probed by (7)Li solid state NMR spectroscopy using spin-alignment echo (SAE) and spin-lattice relaxation (SLR) measurements. Between T = 295 K and 400 K extremely slow Li jump rates tau(-1) ranging from 1 s(-1) to about 2200 s(-1) were directly measured by recording the decay of spin-alignment echoes as a function of mixing time and constant evolution time. The results point out the slow Li diffusion in non-intercalated Li(4)Ti(5)O(12) x tau(-1) (1/T) follows Arrhenius behaviour with an activation energy E(ASAE) of about 0.86 eV. Interestingly, E(ASAE) is comparable to activation energies deduced from conductivity measurements (0.94(1) eV) and from SLR measurements in the rotating frame (0.74(2) eV) rather than from those performed in the laboratory frame, E(A)(low-T) = 0.26(1) eV at low T.     

Rutile-TiO2 nanocoating for a high-rate Li4Ti5O12 anode of a lithium-ion battery

Well-defined Li(4)Ti(5)O(12) nanosheets terminated with rutile-TiO(2) at the edges were synthesized by a facile solution-based method and revealed directly at atomic resolution by an advanced spherical aberration imaging technique. The rutile-TiO(2) terminated Li(4)Ti(5)O(12) nanosheets show much improved rate capability and specific capacity compared with pure Li(4)Ti(5)O(12) nanosheets when used as anode materials for lithium ion batteries. The results here give clear evidence of the utility of rutile-TiO(2) as a carbon-free coating layer to improve the kinetics of Li(4)Ti(5)O(12) toward fast lithium insertion/extraction. The carbon-free nanocoating of rutile-TiO(2) is highly effective in improving the electrochemical properties of Li(4)Ti(5)O(12), promising advanced batteries with high volumetric energy density, high surface stability, and long cycle life compared with the commonly used carbon nanocoating in electrode materials.     

Epitaxial growth and electrochemical properties of Li4Ti5O12 thin-film lithium battery anodes

Epitaxial Li(4)Ti(5)O(12) thin-films were successfully synthesized on SrTiO(3) single-crystal substrates with (111), (110), and (100) lattice plane orientations using pulsed laser deposition (PLD). Thin-film X-ray diffraction (XRD) revealed that the Li(4)Ti(5)O(12) films had the same orientation as the SrTiO(3) substrates: Li(4)Ti(5)O(12) (111) on SrTiO(3) (111), Li(4)Ti(5)O(12) (110) on SrTiO(3) (110), and Li(4)Ti(5)O(12) (100) on SrTiO(3) (100). These epitaxial films contained island structures, and the morphology of the (111), (110), and (100) films, observed by field emission scanning electron microscopy (FE-SEM), exhibited angular, needle-like, and circular shapes, respectively. The electrochemical properties of 20 nm thick Li(4)Ti(5)O(12) (111) and (110) films were investigated by cyclic voltammetry. Reversible intercalation proceeded through both lattice planes due to the three-dimensional diffusion pathway of lithium in the spinel framework. Reduction peaks in the first cathodic scan appeared at different positions from those in subsequent scans, suggesting a surface reconstruction at the Li(4)Ti(5)O(12) surface due to interfacial reactions.     

I~-的光电化学氧化与光助充电二次锂离子电池

采用扫描电子显微镜、X射线衍射和粉末微电极分别考察了TiO2粉末的形貌、结构以及氧化I-的光电化学行为.结果表明,TiO2粉末晶型为锐钛矿,粒径在100～200 nm范围内.在光照条件下,在TiO2半导体电极上电化学氧化I-生成I2的超电势数值降低约1 V.以TiO2/ITO和Li4Ti5O12分别作为正负极,电解液为碳酸丙烯酯(PC)+LiClO4+LiI,并以聚偏氟乙烯(PVDF)作为隔膜构成分隔式电解池,进行整体电解并结合紫外-可见光谱进行分析.结果表明,该装置在光照条件下电池充电电压比非光照条件下的充电电压降低约0.9 V,且充电效率接近100%.该光电化学装置是一种可以利用光能充电的二次锂离子电池.     

水热法合成高功率锂离子二次电池用球形Li4Ti5O12负极材料

以球形TiO2和LiOH溶液为反应物,通过水热法合成了尖晶石型Li4Ti5O12,并使用X射线衍射(XRD)、傅里叶变换红外(FTIR)光谱、扫描电镜(SEM)和激光粒度分布(PSD)对其结构、形貌和电化学性能进行了表征.结果表明:通过该法得到的产品颗粒大小均匀,粒度分布狭窄,结构与标准Li4Ti5O12谱图一致.实验选定温度下所得的Li4Ti5O12均表现出良好的电化学性能.其中,800°C热处理所得样品的电化学性能最好,室温下,以35mA·g-1的电流密度进行充放电,其可逆容量达到162mAh·g-1,同时这种材料也表现出良好的倍率性能,即使在720mA·g-1的电流密度条件下进行充放电,其可逆容量仍可达到124mAh·g-1.     

P(VdF-HFP)-基离子液体复合聚合物电解质的阴极稳定性及热稳定性

以聚偏氟乙烯-六氟丙烯P(VdF-HFP)聚合物为基体, 制备了含离子液体1-甲基-3-乙基咪唑六氟磷酸盐(EMIPF6)、用于锂离子电池的离子液体复合聚合物电解质[P(VdF-HFP)/LiPF₆/EMIPF₆/EC(碳酸乙烯酯)-PC(碳酸丙烯酯)]. 采用热重分析法以及燃烧实验测试了复合聚合物电解质的热稳定性. 离子电导率测试表明, 离子液体的存在显著改善了复合聚合物电解质的离子传输; 循环伏安测试表明, 添加剂EC和PC的加入提高了复合电解质的阴极稳定性, 制得的离子液体复合聚合物电解质在0.3-4.3 V 电压范围内稳定存在. Li₄Ti₅O₁₂ 和LiCoO₂为电极材料、P(VdF-HFP)/LiPF₆/EMIPF₆/EC-PC 为电解质的半电池表现出优良的循环性能, 0.1C充放电倍率下, Li/LiCoO₂和Li/Li₄Ti₅O₁₂半电池的可逆容量分别为130和144 mAh·g^-1. 但EC、PC在一定程度上降低了离子液体复合聚合物电解质的热稳定性.