Comparative experimental studies on the mechanical and degradation properties of natural fibers reinforced polypropylene composites

Coir/silk fiber-reinforced polypropylene (PP) based unidirectional composites (40 wt.%) were manufactured by compression molding. Coir/silk fibers and PP sheets were treated with ultraviolet radiation at different intensities and then composites were fabricated. It was found that mechanical properties of irradiated silk/irradiated PP composites were found to increase significantly compared to the untreated ones and even higher than that of irradiated coir/irradiated PP composites. Soil degradation tests indicated that irradiated coir/irradiated PP composites significantly lost much of its mechanical properties, but irradiated silk/irradiated PP composites retained their strength of its original integrity. Scanning electron microscopy and water uptake of both types of composites were also investigated.     

Effect of chemical modifications of the pineapple leaf fiber surfaces on the interfacial and mechanical properties of laminated biocomposites

Natural fiber reinforced renewable resource based laminated composites were prepared from biodegradable poly(lactic acid) (PLA) and untreated or surface-treated pineapple leaf fibers (PALF) by compression molding using the film stacking method. The objective of this study was to determine the effects of surface treatment of PALF on the performance of the fiber-reinforced composites. X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) were used to aid in the analysis. The mechanical properties of the PLA laminated composites were improved significantly after chemical treatment. It was found that both silane- and alkali-treated fiber reinforced composites offered superior mechanical properties compared to untreated fiber reinforced composites. The effects of temperature on the viscoelastic properties of composites were studied by dynamic mechanical analysis (DMA). From the DMA results, incorporation of the PALF fibers resulted in a considerable increase of the storage modulus (stiffness) values. The heat defection temperature (HDT) of the PALF fiber reinforced PLA laminated composites was significantly higher than the HDT of the neat PLA resin. The differential scanning calorimeter (DSC) results suggest that surface treatment of PALF affects the crystallization properties of the PLA matrix. Additionally, scanning electron microscopy (SEM) was used to investigate the distribution of PLA within the fiber network. SEM photographs of fiber surface and fracture surfaces of composites clearly indicated the extent of fiber–matrix interface adhesion. It was found that the interfacial properties between the reinforcing PALF fibers and the surrounding matrix of the laminated composite are very important to the performance of the composite materials and PALF fibers are good candidates for the reinforcement fiber of high performance laminated biodegradable biocomposites.     

Lignocellulosic composites with grafted polystyrene interfaces

The effects of surface grafting of a polymer onto lignocellulosic fiber surface and processing methods on both the interfacial interactions and the resulting composite properties of the fiber-reinforced thermoplastic composites were investigated. Chemithermomechanical pulp (CTMP) wood fiber was used as a reinforcement, which has been chemically modified by radical polymer grafting of styrene onto the fiber surfaces. The chemically modified CTMP fiber was then compounded with polystyrene (PS). Two different processing methods, both compression and injection moldings, were performed to prepare the wood-fiber-reinforced composites. Experimental results showed that surface modification of wood fiber leads to an obvious increase in mechanical properties of the fiber-reinforced composites as compared to the untreated fiber composites. The enhancement of mechanical properties is much greater through injection molding compared with compression molding owing to occurrence of orientation, and better mixing and interaction between the fiber and the matrix by injection molding. An improvement in fiber wetting properties and adhesion by the matrix was observed through scanning electron microscopy for the surface grafted fiber reinforced composites. Untreated wood fiber exhibited a smooth surface without adhered polymer, indicating poor adhesion, while polymer attached to the surface was seen on treated cellulose fiber due to the higher fiber-matrix interactions.     

Thermal behavior of chemically treated and untreated sisal fiber reinforced composites fabricated by resin transfer molding

Using thermogravimetric analysis (TGA), the thermal behavior of sisal fibers and sisal/polyester composites, fabricated by resin transfer molding (RTM), has been followed. Chemical treatments have been found to increase the thermal stability, which has been attributed to the resultant physical and chemical changes. Scanning electron microscopy (SEM) and infrared (FT-IR) studies were also performed to study the structural changes and morphology in the sisal fiber during the treatment. The kinetic studies of thermal degradation of untreated and treated sisal fibers have been performed using Broido method. In the composites, as the fiber content increases, the thermal stability of the matrix decreases. The treated fiber reinforced composites have been found to be thermally more stable than the untreated derivatives. The increased thermal stability and reduced moisture behavior of treated composites have been correlated with fiber/matrix adhesion.     

Short sisal fiber reinforced polypropylene composites: the role of interface modification on ultimate properties

Sisal fibers have been used for the reinforcement of polypropylene matrix. The compatibilization between the hydrophilic cellulose fiber and hydrophobic PP has been achieved through treatment of cellulose fibers with sodium hydroxide, isocyanates, maleic anhydride modified polypropylene (MAPP), benzyl chloride and by using permanganate. Various fiber treatments enhanced the tensile properties of the composites considerably, but to varying degrees. The SEM photomicrographs of fracture surfaces of the treated composites clearly indicated the extent of fiber–matrix interface adhesion, fiber pullout and fiber surface topography. Surface fibrillation is found to occur during alkali treatment which improves interfacial adhesion between the fiber and PP matrix. The grafting of the fibers by MAPP enhances the tensile strength of the resulting composite. It has been found that the urethane derivative of polypropylene glycol and cardanol treatments reduced the hydrophilic nature of sisal fiber and thereby enhanced the tensile properties of the sisal–PP composites, as evident from the SEM photomicrographs of the fracture surface. The IR spectrum of the urethane derivative of polypropylene glycol gave evidence for the existence of a urethane linkage. Benzoylation of the fiber improves the adhesion of the fiber to the PP matrix. The benzoylated fiber was analyzed by IR spectroscopy. Experimental results indicated a better compatibility between benzoylated fiber and PP. The observed enhancement in tensile properties of permanganate-treated composites at a low concentration is due to the permanganate-induced grafting of PP on to sisal fibers. Among the various treatments, MAPP treatment gave superior mechanical properties. Finally, experimental results of the mechanical properties of the composite have been compared with theoretical predictions.     

Effect of Fiber Surface Modification on the Interfacial and Mechanical Properties of Kenaf Fiber-Reinforced Thermoplastic and Thermosetting Polymer Composites

The surfaces of kenaf fibers were treated with three different silane coupling agents. 3-glycidoxypropyltrimethoxy silane (GPS), 3-aminopropyltriethoxy silane (APS), and 3-methacryloxypropyltrimethoxy silane (MPS). Among them, the most effective one for the property improvement was GPS when it was applied to the kenaf fiber surfaces at 0.5 wt%. Thermoplastic polypropylene (PP) and thermosetting unsaturated polyester (UPE) matrix composites with chopped kenaf fibers untreated and treated at different GPS concentrations from 0.1 wt% to 5 wt% were fabricated using compression molding technique. The present study demonstrates that the interfacial, flexural, tensile, and dynamic mechanical properties of both kenaf/PP and kenaf/UPE composites importantly depend on the GPS treatments done at different concentrations. The greatest property improvement of both thermoplastic and thermosetting polymer composites was obtained with the silane treatment at 0.5 wt% and the mechanical properties were comparable with E-glass composites prepared the same polymer matrix under the corresponding fiber length and fiber loading. The results also agreed with each other with regard to their interfacial shear strength, flexural properties, tensile properties, storage modulus, with support of fracture surfaces of the composites.     

Banana fiber strands–reinforced polymer matrix composites

Banana fiber (BF)-reinforced low-density polyethylene (LDPE) unidirectional composites were fabricated by the compression molding process with 40 wt% fiber loading. The fibers were modified with methylacrylate (MA) mixed with methanol (MeOH) along with 2% benzyl peroxide under thermal curing method at different temperatures (50–90 °C) for different curing times (10–50 min) in order to have better compatibility with the matrix. The effect of fiber surface modification on the mechanical properties (tensile and impact properties) of the composites were evaluated. Monomer concentration, curing temperature, and curing time were optimized in terms of polymer loading and mechanical properties. The mechanical properties were found to be improved based on the improved interaction between the reinforcement and the matrix. Optimized BFs were again treated with 2–5 wt% starch solutions and composites made of 4% starch treated BF showed the highest mechanical properties than that of MA treated composites. Scanning electron microscopy (SEM) was performed to get an insight into the morphology of the composites. Water uptake and soil degradation test of the composites were also investigated.     

The effect of interphase modification on carbon fiber/polyarylacetylene resin composites

Interfacial modification for carbon fiber (CF) reinforced polyarylacetylene (PAA) resin, a kind of non-polar, was investigated. The high carbon phenolic resin was used as coating to treat the surface of CF after oxidation. Atomic force microscopy (AFM) with force modulation mode was used to analyze the interphase of composite. The interlaminar shear strength (ILSS) and mechanical properties of CF/PAA composites were also measured. It was found that the CF/PAA composites treated with oxidation and coating after oxidation had transition area between carbon fiber and PAA resin. The existence of transition area led to the improvement of interfacial performance of composites. Specially, the thickness and stiffness of interphase of composite treated with coating after oxidation were more suitable for CF/PAA composites. Thus, the composite treated with coating after oxidation had the highest value of ILSS and the best mechanical properties.     

Discontinuous basalt and glass fiber reinforced PP composites from textile prefabricates: effects of interfacial modification on the mechanical performance

Spun and blown basalt fibers and their PP matrix composites were investigated. The composites were manufactured by hot pressing technology from carded and needle punched prefabricate using PP fiber as matrix material. Glass and blown basalt fibers were treated with reaction product of maleic acid-anhydride and sunflower oil while spun basalt fibers had a surface coating of silane coupling agent. Fibers were investigated with tensile tests while composites were subjected to static and dynamic mechanical tests. The results show that blown basalt fibers have relatively poor mechanical properties, while spun basalt fibers are comparable with glass fibers regarding geometry and mechanical performance. The static and dynamic mechanical properties of glass and spun basalt fiber reinforced composites are similar and are higher than blown basalt fiber reinforced composites. Results were supported with SEM micrographs.     

Fabrication and characterization of jute fabrics reinforced polypropylene-based composites: effects of ionizing radiation and disaccharide (sucrose)

Composites were prepared successfully by compression molding technique using jute fabrics (reinforcing agent) and polypropylene (matrix). Jute fabrics were treated with disaccharide (sucrose) solution and composites were fabricated with the treated fabric and polypropylene. The fiber content of the prepared composites was 40% by weight. It was found that the sucrose (2% solution) decreased the tensile strength (TS) and elongation at break about 6% and 37%, respectively, but tensile modulus and impact strength improved about 27% and 32%, respectively. When gamma radiation was applied through the untreated and treated composites the mechanical properties were improved much higher in non-treated Jute/PP-based composites than that of sucrose treated composites. For 5.0?kGy gamma dose the highest mechanical properties were observed for non-treated composites. At 5.0?kGy gamma dose the improvement of TS was 14% and 2% for non-treated and sucrose treated composites, respectively. The water uptake property of the sucrose treated composites was performed up to 10 days and composites absorbed 18% water. The functional groups of the both composites were analyzed by Fourier transform infrared spectroscopy machine. The scanning electron microscopic images of the both composites were taken for the surface and fiber adhesion analysis.     

Influence of Fiber Surface Treatment on Mechanical Properties of CF/PET Composites

Carbon fiber (CF) / poly (ethylene terephthalate) (PET) composites were prepared with various contents (2–15wt%) of short carbon fibers. To investigate the effect of surface treatment of the CF on the mechanical properties of the composites, three specimens were prepared; those with short carbon fibers (called SCF), short carbon fibers oxidized with nitric acid (called NASCF) and the fibers oxidized with nitric acid and treated with silane coupling agent (called SCSCF). Flexural, tensile and impact tests were performed to observe mechanical behavior of the specimens. The morphology of the specimens was also studied with a scanning electron microscope (SEM). SCSCF composite had better mechanical properties than the other composites with the same content of carbon fibers since the coupling agent resulted in better interfacial adhesion between the fiber and the matrix.     

Effect of fiber surface treatments on the fiber–matrix interaction in banana fiber reinforced polyester composites

Cellulosic fibers have been used as cost-cutting fillers in plastic industry. Among the various factors, the final performance of the composite materials depends to a large extent on the adhesion between the polymer matrix and the reinforcement and therefore on the quality of the interface. To achieve optimum performance of the end product, sufficient interaction between the matrix resin and the cellulosic material is desired. This is often achieved by surface modification of the resin or the filler. Banana fiber, the cellulosic fibers obtained from the pseudo-stem of banana plant (Musa sepientum) is a bast fiber with relatively good mechanical properties. The fiber surface was modified chemically to bring about improved interfacial interaction between the fiber and the polyester matrix. Various silanes and alkali were used to modify the fiber surface. Modified surfaces were characterized by SEM and FTIR. The polarity parameters of the chemically modified fibers were investigated using the solvatochromic technique. The results were further confirmed by electrokinetic measurements. Chemical modification was found to have a profound effect on the fiber–matrix interactions. The improved fiber–matrix interaction is evident from the enhanced tensile and flexural properties. The lower impact properties of the treated composites compared to the untreated composites further point to the improved fiber–matrix adhesion. In order to know more about the fiber–matrix adhesion, fractured surfaces of the failed composites where further investigated by SEM. Of the various chemical treatments, simple alkali treatment with NaOH of 1% concentration was found to be the most effective. The fiber–matrix interactions were found to be dependent on the polarity of the modified fiber surface.     

Kenaf/polypropylene biocomposites: effects of electron beam irradiation and alkali treatment on kenaf natural fibers

Thermal and dynamic mechanical properties of kenaf natural fiber reinforced polypropylene (PP) biocomposites were examined to compare the effects of natural fiber treatment by electron beam irradiation (EBI) and alkalization. The alpha cellulose contents, the functional groups on the surfaces and the thermal stability of the untreated and treated kenaf fibers were studied. Kenaf fiber/polypropylene(PP) biocomposites were fabricated by means of a compression molding technique using chopped kenaf fibers treated with electron beam (EB) dosages of 100, 200, 500 kGy or with NaOH concentrations of 2, 5, 10 wt%, respectively. The thermal stability, the dynamic mechanical and the interfacial properties of untreated and treated kenaf/PP biocomposites were also investigated through a thermogravimetric analysis, a dynamic mechanical analysis and a fractographic observation, respectively. The results show that the characteristics of kenaf fibers and biocomposites depended on the different treatment level with the EB dosages or on the NaOH concentrations used. In this study, the modification of kenaf fiber surfaces at 200 kGy EBI and treatment with 5 wt% NaOH was most effective for improving the performance of kenaf/PP biocomposites. This study suggests that EBI can be used for modification of natural fiber as an environmentally friendly process and contribute to an improvement in the performances of kenaf/PP biocomposites.     

Micromechanical Behavior of Carbon Nanotube-Covered SiC Fibers in Polymer Matrix Composites

The incorporation of nanotube-covered fibers in continuous fiber/epoxy composites has been shown to influence the mechanical, electrical, and thermal properties of the composite. Increased interlaminar shear stress, flexural strength and modulus have been reported in such composites over composites containing bare fibers. In this study, the microstructure and interfacial shear strength (ISS) of continuous silicon carbide fiber/epoxy composites with and without nanotubes grown from the SiC fiber surface were investigated with micro-Raman spectroscopy (MRS) and microscopy. The fibers with nanotubes grown from the surface were found to have a reduced ISS compared with the bare fibers. Electron microscopy showed good wetting of epoxy in the nanotube forests, but poor attachment of the nanotube forests to the fibers. These results suggest that the mechanism leading to improvements in bulk composite properties is not due to an improvement in the fiber/matrix ISS.     

Effect of chemical treatment on dynamic mechanical properties of sisal fiber-reinforced polyester composites fabricated by resin transfer molding

The dynamic mechanical properties of treated sisal fiber-reinforced polyester composites fabricated by resin transfer molding (RTM) have been studied with reference to fiber surface modifications, frequency and temperature. The sisal fibers have been subjected to various chemical and physical treatments like mercerization, heating at 100°C, permanganate, benzoylation and vinyl tris(2-ethoxymethoxy) silane to improve the interfacial bonding with isophthalic polyester resin. Results indicated that treatment changed the storage modulus (E′), loss modulus (E″) and damping factor (tan δ) drastically at a wide range of temperature. The E′ value increased for every treatment, and is maximum for the composites fabricated by benzoylated-treated fibers. The T _g value obtained from the E″value showed an increase as compared to untreated fiber-reinforced composites. The alkali-treated fiber-reinforced composites showed lower tan δ value. Using Arrhenius' equation the activation energy was calculated and found maximum for the composites fabricated by alkali-treated fiber, which shows good fiber/matrix interactions.     

Interfacial mechanical properties of carbon nanotube-deposited carbon fiber epoxy matrix hierarchical composites

Functionalized multiwalled carbon nanotubes were successfully deposited on carbon fibers using four different techniques including dip coating, hand layup, spray up and electrophoretic deposition (EPD). A uniform coating of nanotubes was achieved from EPD in comparison to other coating techniques. Later nanotube-coated fibers by EPD were introduced in epoxy resin to investigate interfacial mechanical properties of the developed hierarchical composites by vacuum bagging technique. The increases in flexural and interlaminar shear properties up to 15% and 18% were observed in composites containing nanotube-coated carbon fibers than composites with virgin carbon fibers, respectively. Microscopic observation revealed the proper impregnation of multiscale reinforcements, i.e., carbon fibers and carbon nanotubes, in resin along with the modification of fiber/matrix interface due to the presence of nanotubes at interface. Finally, the mechanisms for improved mechanical properties were identified along with the presentation of a schematic model for better understanding of the improved performance of hierarchical composite after depositing uniformly dispersed nanotubes on carbon fibers.     

Development and characterization of alkali treated abaca fiber reinforced friction composites

Abaca fibers show tremendous potential as reinforcing components in composite materials. The purpose of this study is to investigate the effect of abaca fiber content on physical, mechanical and tribological properties of abaca fiber reinforced friction composites. The friction composites were fabricated by a compression molder and investigated using a friction test machine. The experiment results show that surface treatment of abaca fibers could improve the mechanical properties of abaca fiber and interface bonding strength of the abaca fiber and composite matrix. Density of friction composites decreased with the increasing of abaca fiber content (0 wt%–4 wt%). The different content of abaca fibers had less effect on hardness of specimens, whereas large of impact strength. The specimen F3 with 3 wt% abaca fibers had the lowest wear rate and possessed the best wear resistance, followed by specimen F4 with 4 wt% abaca fibers. The worn surface morphologies were observed using the Scanning Electron Microscopy for study the tribological behavior and wear mechanism. The results show that a large amount of secondary contact plateaus presented on the worn surface of specimen F3 which had relatively smooth worn surface.     

Study of impact properties and morphology of unidirectional bamboo strips–polyester composites: effect of mercerization

Composites were fabricated with alkali (10%, 15% and 20%) treated bamboo fibers incorporated to the extent of 50% (by volume) and polyester resin. Impact test was made on bamboo strips and composites samples. It was observed that the fracture energy undergoes an increase from untreated to alkali treated bamboo strips. Alkali treated bamboo fiber composites show higher fracture energy value than the untreated bamboo fiber composites. The phenomenal change was quite evident from scanning electron micrographs of the fractured surface. Considering the effects of all factors, the work of fracture shows maximum value in the case of 20% alkali treated bamboo strip composites. It was also observed that the rate of increase of work of fracture value is much higher in the case of composite samples than the bamboo sample. It was explained on the basis of synergism obtained by improved interfacial adhesion between fiber and matrix, and removal of hemicellulose from the bamboo itself, which was evident from the intermolecular H-bonding formation studied by FT-IR.     

In situ surface modification of natural fiber by conducting polyaniline

Newly modified biofibers made up of kenaf fibers (KF) and conducting polyaniline (PANI) were successfully prepared via in situ polymerization. Several characterization methods were done to elucidate the interaction between the KF surfaces and the in situ polymerized PANI. The PANI coated KF (KF/PANI) achieved new electronic properties, without sacrificing its mechanical properties and natural fiber characteristic. Initial mercerization on the KF yielded better PANI coated fibers compared to the untreated KF. Fiber bundle tensile test on the untreated KF/PANI revealed a drop in the unit break of about 48% compared to the untreated neat KF. Meanwhile, the mercerized KF/PANI showed reduction of about 17% compared to the uncoated mercerized KF. The mercerized KF/PANI exhibits polaronic transitions, existence of favorable IR peaks and Raman scattering, enhanced DC conductivity, and better morphological characteristic as a result of the in situ PANI coating. Such electronically modified natural fibers could be suitable as green conducting fillers in composites to replace other synthetic fibers.     

Effects of plasma surface modification on the mechanical properties of carbon fiber and carbon fiber/epoxy composite

_The effect of surface treatment on mechanical properties of carbon fibers has been investigated by application of plasma polymerization of selected monomers in the vapor phase. The role of the fiber-matrix interface on carbon fiber-reinforced epoxy resin composites has also been studied. Composites have been prepared separately by the use of plasma-modified and unmodified carbon fibers in the epoxy resin matrix. The mechanical properties of carbon fibers (Hercules and Grafil) as well as of fiber/epoxy composites were examined by using single filament and three-point bending tests, respectively. It was observed that plasma polymerization treatment at selected plasma conditions led to significant improvement of interlaminar shear and flexural strength values of composites.