Fabrication of optical devices in poly(dimethylsiloxane) by proton microbeam

Optical diffraction grating and micro Fresnel zone plate type structures were fabricated in relatively thin poly(dimethylsiloxane) (PDMS) layers using proton beam writing technique and the performance of these optical devices was tested. PDMS is a commonly used silicon-based organic polymer, optically clear, generally considered to be inert, non-toxic and biocompatible. PDMS has been used as a resist material for direct-write techniques only in very few cases. In this work, PDMS was used as a resist material; the structures were irradiated directly into the polymer. We were looking for a biocompatible, micropatternable polymer in which the chemical structure changes significantly due to proton beam exposure making the polymer capable of proton beam writing. We demonstrated that the change in the structure of the polymer is so significant that there is no need to perform any development processes. The proton irradiation causes refractive index change in the polymer, so diffraction gratings and other optical devices like Fresnel zone plates can be fabricated in this way. The observed high order diffraction patterns prove the high quality of the created optical devices.     

LiNbO3质子交换波导及其退火效应

采用质子交换技术,以苯甲酸为交换源,实验研究X-切LiNbO₃质子交换平面波导及其退火效应。利用棱镜耦合器测出波导模折射率。采用费米函数,由模折射率确定出波导折射率分布随退火时间的变化关系,给出了分布参数和曲线.     

低温下ZnSe-ZnS多量子阱的光致发光光谱和喇曼散射谱

本文报导了2K下,在GaAs(100)衬底上用MOCVD方法生长的ZnSe-ZnS多量子阱材料的光致发光光谱和喇曼散射谱.用共振激发、共振喇曼和共振瑞利散射等方法对各发光谱带和喇曼散射峰的来源和机制进行了鉴别.     

低温下ZnSe－ZnS多量子阱的光致发光光谱和喇曼散射谱

本文报导了２Ｋ下，在ＧａＡｓ（１００）衬底上用ＭＯＣＶＤ方法生长的ＺｎＳｅ－ＺｎＳ多量子阱材料的光致发光光谱和喇曼散射谱．用共振激发、共振喇曼和共振瑞利散射等方法对各发光谱带和喇曼散射峰的来源和机制进行了鉴别．     

High-frequency micro-inductor fabricated on NiCuZn ferrite substrates

We have fabricated the planar micro-inductors directly on a NiCuZn ferrite substrate. Due to NiCuZn's high resistivity, no insulator is required between the coil and the magnetic film; an advantage in terms of ease fabricated and stray capacitance reduction. Sandwiched inductors show improvement of inductance from 16 to 80 nH at 1 MHz compared with the coreless inductors, and the increment of inductance is larger than the sandwiched thin film inductor.     

Temperature and hydration dependence of proton MAS NMR spectra in MCM-41: Model based on motion induced chemical shift averaging

The proton MAS NMR spectra in MCM-41 at low hydration levels (less than hydration amounting to one water molecule per surface hydroxyl group) show complex proton resonance peak structures, with hydroxyl proton resonances seen in dry MCM-41 disappearing as water is introduced into the pores and new peaks appearing, representing water and hydrated silanol groups. Surface hydroxyl group–water molecule chemical exchange and chemical shift averaging brought about by a water molecule visiting different surface hydrogen bonding sites have been proposed as possible causes for the observed spectral changes. In this report a simple model based on chemical shift averaging, due to the making and breaking of hydrogen bonds as water molecules move on the MCM-41 surface, is shown to fully reproduce the NMR spectra, both as a function of hydration and temperature. Surface proton–water proton chemical exchange is not required in this model at low hydration levels.     

Spiral terraces and spin frustration in layered antiferromagnetic Cr(001) films

We have successfully fabricated a novel type of high-density spiral terraces on Cr(001) films. The influence of nanoscale spiral terraces on layered antiferromagnetic ordering of Cr(001) films has been studied at room temperature by direct imaging of both topographic and magnetic structures using spin-polarized scanning tunneling spectroscopy. Spin frustration and asymmetric magnetic ordering due to dense spiral terraces are observed. Sizable modification of the layered antiferromagnetic order is found to be originating from the topological asymmetry as confirmed by the continuum micromagnetic simulation.     

非线性变周期全息光栅的制作

叙述一种用发散光束来的制作变周期光栅的方法,简单的系统保证了两束形成全息干涉的光强相等这一点对获得高反衬结构的光栅图形是重要的。在显影过程中用He-Ne激光作为衍射效率的在位监控。     

PVA nano composite membrane for DMFC application

A new PEM composite membrane comprising of polyvinyl alcohol (PVA), sulfonic acid functionalized CNT and fluorinated MMT has been fabricated. Composite polymer membrane has been prepared by simple solution casting method. Composite properties have been evaluated by using thermal gravimetric analysis (TGA), scanning electron microscopy (SEM), and FTIR techniques. The proton conductivity, methanol crossover and water uptake properties of newly fabricated membrane have been studied. The polymer membrane shows good thermal properties. The water content is in the range of 35-45%. Especially, it has been found that the fluorinated MMT used in this study plays a decisive role in water uptake and acts as a hydrophobic surface for controlling the swelling. The proton conductivities and the methanol permeabilities of all the membranes are in the range of 10^− 3 to 10^− 2 S/cm and 2.08 × 10^− 6 cm²/s at room temperature, respectively.     

1.5μm质子交换铌酸锂光波导TE0模偏振器

在１．５μｍ光波长，首次研制出质子交换铌酸锂光波导ＴＥ０模偏振器。器件由嵌在Ｔｉ扩散波导之间的一段质子交换波导构成，器件长度为２ｍｍ。实验测得，偏振器的消光比和带尾纤插入损耗分别为４２ｄＢ和４．３ｄＢ。     

Si-based materials and devices for light emission in silicon

We report on the fabrication and performances of extremely efficient Si-based light sources. The devices consist of MOS structures with erbium (Er) implanted in the thin gate oxide. The devices exhibit strong 1.54 μm electroluminescence (EL) at 300 K with a 10% external quantum efficiency, comparable to that of standard light-emitting diodes using III–V semiconductors. Er excitation is caused by hot electrons impact and oxide wearout limits the reliability of the devices. Much more stable light-emitting MOS devices have been fabricated using Er-doped silicon rich oxide (SRO) films as gate dielectric. These devices show a high stability, with an external quantum efficiency reduced to 1%. In these devices, Er pumping occurs by energy transfer from the Si nanostructures to the rare-earth ions. Finally, we have also fabricated MOS structures with Tb- and Yb-doped SiO₂ which show room temperature EL at 540 nm (Tb) and 980 nm (Yb) with an external quantum efficiency of a 10% and 0.1%, respectively.     

苯乙烯基吡啶类液晶化合物的分子结构及相变过程的光谱研究

通过本乙烯基吡啶和不同脂肪羧酸间的氢键作用构成液晶的方法具有合成路线灵活、简便、易于变化的特点,本文通过变温红外光谱对做为质子受体的苯乙烯基吡啶粉液晶化合物的分子结构和相变过程中分子排列的变化进行了研究,结果表明在液晶分子中象羰基这样的偶极矩较大的极性基团,对分子所处的相态分子间的相互排列比较敏感。在红外光谱中羰基伸缩振动的变化可以看作是液晶分子相态转变的标志。     

Direct observation of the Aharonov-Casher phase

Ring structures fabricated from HgTe/HgCdTe quantum wells have been used to study Aharonov-Bohm type conductance oscillations as a function of Rashba spin-orbit splitting strength. We observe nonmonotonic phase changes indicating that an additional phase factor modifies the electron wave function. We associate these observations with the Aharonov-Casher effect. This is confirmed by comparison with numerical calculations of the magnetoconductance for a multichannel ring structure within the Landauer-Büttiker formalism.     

Strengthen the performance of sulfonated poly(ether ether ketone) as proton exchange membranes with phosphonic acid functionalized carbon nanotubes

Nanocomposite polymers based on phosphonic acid functionalized carbon nanotubes (CNT-POH) and sulfonated poly(ether ether ketone) (SPEEK) have been fabricated and employed as highly efficient proton exchange membranes. CNT-POH were synthesized through the grafting of carbon nanotubes (CNT) with diethylphosphatoethyl triethoxysilane and subsequent acidification of phosphate to phosphonic acid ligands. Incorporating CNT-POH into SPEEK matrix improves the proton conductivity at different temperatures and relative humidity, which can be attributed to the homogeneous dispersion of highly hydrophilic phosphonic acid groups and the formation of proton transport channels in the membrane. The methanol permeability of the composite membranes is also decreased, owing to the increased tortuosity of the methanol transport channel. The CNT in SPEEK matrix also enhance the dimensional stability and mechanical property remarkably. Consequently, this phosphonic acid functionalized CNT/SPEEK composite membrane (SPEEK-POH) is a potential candidate for application in direct methanol fuel cells (DMFC).     

Laser nanosources based on planar photonic crystals as new platforms for nanophotonic devices

Two-dimensional photonic crystal lasers have been fabricated on III–V semiconductor slabs. Tuning of the spontaneous emission in micro and nanocavities has been achieved by accurate control of the slab thickness. Different structures, some of them of new application to photonic crystal lasers, have been fabricated like the Suzuki-phase or the coupled-cavity ring-like resonators. Laser emission has been obtained by pulsed optical pumping. Optical characterization of the lasing modes have been performed showing one or more laser peaks centred around 1.55 μm. Far field characterization of the emission pattern has been realized showing different patterns depending on the geometrical shape of the structures. These kinds of devices may be used as efficient nanolaser sources for optical communications or optical sensors.     

Enhancement of radiation hardness of InP-based HEMT with double Si-doped plane

An anti-radiation structure of In P-based high electron mobility transistor(HEMT) has been proposed and optimized with double Si-doped planes. The additional Si-doped plane under channel layer has made a huge promotion in channel current, transconductance, current gain cut-off frequency, and maximum oscillation frequency of In P-based HEMTs. Moreover, direct current(DC) and radio frequency(RF) characteristic properties and their reduction rates have been compared in detail between single Si-doped and double Si-doped structures after 75-keV proton irradiation with dose of 5× 10¹¹ cm^-2,1× 10¹² cm^-2, and 5× 10¹² cm^-2. DC and RF characteristics for both structures are observed to decrease gradually as irradiation dose rises, which particularly show a drastic drop at dose of 5× 10¹² cm^-2. Besides, characteristic degradation degree of the double Si-doped structure is significantly lower than that of the single Si-doped structure, especially at large proton irradiation dose. The enhancement of proton radiation tolerance by the insertion of another Si-doped plane could be accounted for the tremendously increased native carriers, which are bound to weaken substantially the carrier removal effect by irradiation-induced defects.     

632.8nm波长质子交换光波导型偏振器的研究

在可见光域研制出钛扩散铌酸锂质子交换光波导偏振器，同时，给出波导偏振器参数测试装置。在理论上，利用物理光学和波导色散理论分析与计算了这种偏振器的消光比，分析了影响器件性能的各种因素，理论计算与实验结果符合良好。     

Contact welding study of carbon nanotube with ZnO nanowire

Study of proton beam induced welding of multiwall carbon nanotubes (MWCNTs) with ZnO nanowires (NWs) has been carried out by proton (H⁺) beam irradiation. The samples were irradiated by 70-keV proton (H⁺) ion beams at different substrate temperatures. The irradiation-induced defects in CNTs and ZnO NWs were greatly reduced at elevated temperature. The crystalline structure of ZnO NWs and MWCNTs were found to remain stable after the irradiation at 700 K. As a preparation step, a coupling of two parallel ZnO NWs with irradiation has also been demonstrated. The welding mechanisms of MWCNTs and ZnO NWs were also been suggested. These two welding processes between same and distinct nanostructures to form homo- and hetero-junctions have provided an opportunity to mass produce interconnecting one-dimensional structures used for the manufacturing of future nanowire-based electronic circuits and devices.     

Periodic domain structures formed under electron-beam irradiation in LiNbO3 plates and Ti:LiNbO3 planar waveguides of the Y cut

Regular domain structures on the Y cuts of the LiNbO₃ substrates and Ti:LiNbO₃ waveguide structures based on these substrates have been fabricated under electron-beam irradiation. It has been revealed that the domains in undoped and titanium-doped LiNbO₃ crystals are formed as a result of different processes. It has been demonstrated using chemical etching and waveguide second-harmonic generation that regular domain structures in the Ti:LiNbO₃ waveguides are formed at a depth of approximately 8 μm from the surface, where the titanium concentration does not exceed 2 mol %. The quasi-synchronous waveguide optical second harmonic generation with an efficiency of 8.8% has been obtained using the fabricated structures.     

Proton reaction cross sections as measures of the spatial distibutions of neutrons in exotic nuclei

Proton and neutron densities from Skyrme-Hartree-Fock calculations of a number of nuclei with masses ranging from 28 to 58 have been used to generate optical potentials for proton elastic scattering. Those potentials, generated by folding the structure functions with effective in-medium nucleon-nucleon (NN) interactions, have been used to evaluate proton total reaction cross sections; cross sections that reveal signatures of the structures.