Determination of aromatic amines in aqueous extracts of polyurethane foam using hydrophilic interaction liquid chromatography and mass spectrometry

A method is presented for the determination of aromatic amines in aqueous extracts of polyurethane (PUR) foam. The method is based on the extraction of PUR foam using aqueous acetic acid (0.1%, w/v) followed by determination of extracted aromatic amines using hydrophilic interaction liquid chromatography (HILIC) and tandem mass spectrometry (MS/MS) with positive electrospray ionisation. The injections of volumes up to 5 μL of aqueous solutions were made possible by on-column focusing with partially filled loop injections. The fragmentation patterns for 2,4- and 2,6-toluene diamine (TDA) and 4,4′-methylene dianiline (MDA) were clarified by performing a hydrogen-deuterium exchange study.TDA and MDA were determined using trideuterated 2,4- and 2,6-TDA and dideuterated 4,4′-MDA as internal standards. Linear calibration graphs were obtained over the range 0.025-0.5 μg mL⁻¹ with correlation coefficients >0.996 and the instrumental detection limit for each compound was <50 fmol. The stability of the amines was influenced by the matrix, so their concentrations decreased over time.Agreement was observed between the results of analyses of PUR foam extracts by HILIC-MS/MS and results obtained by ethyl chloroformate derivatisation and reversed phase (RP) liquid chromatography-mass spectrometry (LC-MS/MS).TDA was observed to be unstable in extracts of foam but not in pure solutions.     

Biomonitoring of workers exposed to aromatic amines in rubber vulcanization

Summary A method based on solid phase extraction and reversed phase LC for quantitation of IPPD (N-(1-methylethyl)-N′-phenyl-1,4-Benzendiamine) and 6PPD (N-(2,3-dimethylpropyl)-N′-phenyl-1,4-Benzendiamine) in the urine of rubber vulcanization workers is described. The method provided a 91.8 +/- 1.45 % mean recovery of IPPD and 93.8 +/- 1.65 % mean recovery of 6PPD from fortified urines in the 10.0 to 250.0 μg l⁻¹ range. Standard curves bracketing this concentration range had linear coefficients greater than 0.9989. The average relative standard deviation for the entire concentration range was 1.93 % for IPPD and 2.3 % for 6PPD. The method has been applied successfully to biomonitoring IPPD in the nanomole range in the urine of rubber vulcanization workers.     

Determination of novel aromatic amines in environmental samples by gas chromatography/mass spectrometry

A number of compounds belonging to five chemical classes of aromatic amines were identified by electron impact mass spectrometry, both in the vapor phase and in suspended particulate matter collected in an area subjected to heavy traffic. This paper presents the mass spectra of new aromatic amines, proposed mechanisms for formation of the major ions obtained by electron impact, concentrations of each class in 13 environmental samples, and the distribution of the individual compounds of the major chemical classes (greater than 80% by weight).     

Study of fungal degradation products of polycyclic aromatic hydrocarbons using gas chromatography with ion trap mass spectrometry detection

Representatives of polycyclic aromatic hydrocarbons (PAHs) were degraded by ligninolytic fungus Irpex lacteus. The products were analyzed by GC-Ion trap mass spectrometry. The combination of full scan mass spectra, product ion scans (MS-MS) and derivatization of the degradation products of anthracene, phenanthrene, fluoranthene and pyrene provided further insight in the degradation mechanism initiated by I. lacteus. Particularly, the product ion scans enabled the interpretation of unknown degradation products, even though they were only produced at trace level. Most of the structures suggested were later confirmed with authentic standards.     

Highly sensitive high-performance liquid chromatography/selective reaction monitoring mass spectrometry method for the determination of cyclophosphamide and ifosfamide in urine of health care workers exposed to antineoplastic agents

In recent years, the potential for exposure of health care workers to antineoplastic agents has led to the establishment of more restrictive government and professional standards and procedures for handling cytotoxic drugs. Therefore, the detection of low exposure levels is a new and important aim of biological monitoring. In the present paper we report an assay for the simultaneous determination of cyclophosphamide (CP) and ifosfamide (IF) in urine, using electrospray ionization liquid chromatography/tandem mass spectrometry with selective reaction monitoring (HPLC/SRM-MS). A rapid sample preparation procedure uses a solid-phase extraction stage with C18 columns. The urine assay is linear over the range 0.02 to 0.4 microg/L, with lower limits of quantification (LLOQs) of 0.02 and 0.04 microg/L for CP and IF. The accuracy and precision have been carried out through the validation study. The intra-day precision, expressed as relative standard deviation (RSD), is found to be always less than 14.7% for both analytes. The overall precision, assessed on three different days, is less than 15.0%. The recovery of ozaxaphosphorines ranges from 83.5% (CP) to 88.5% (IF) with a RSD always less than 14.6%. The uncertainty of the overall method was also evaluated, to identify possible sources of error. The combined uncertainty was less than 25% over all the days of the validation study. This method is selective and sensitive enough to determine trace levels of CP and IF in a range of urine concentrations relevant to performing low exposure assessment.     

Isotope dilution gas chromatography/mass spectrometry for platinum determination in urine

The therapeutic importance of platinum (Pt) compounds, the growing accessibility of gas chromatography/mass spectrometry (GC/MS) systems in clinical laboratories, and the lack of a mass spectrometric method for the determination of Pt in biological samples motivated us to develop an isotope dilution GC/MS assay for Pt. The method is based on the use of lithium bis(trifluoroethyl) dithiocarbamate, Li(FDEDTC), as a chelating agent and enriched ¹⁹²Pt for isotope dilution. Conditions were optimized for the precise and accurate determination of isotope ratios of Pt by using a 10-m DB-l fused silica capillary column and a reverse-geometry double-focusing mass spectrometer with selected ion monitoring. An overall precision of 1% was obtained by combining within-run precision and between-run precision at the 10-ng level. No appreciable memory effect was observed when samples with different isotope ratios were analyzed sequentially. The method was validated by the quantitation of Pt in National Institute of Standards and Technology freeze-dried urine sample SRM 2670. A concentration value of 125 ± 6 /Lg/L (n = 6) was obtained by using four different sets of isotope ratios in the molecular ion and supports the National Institute of Standards and Technology recommended value of 120 ± ? μg/L. Limits-of-quantitation, estimated at 3 μg/L, are made possible by the high sensitivity of the method and the low blank value for Pt.     

高效液相色谱-串联质谱法测定纺织品中的致癌芳香胺

建立了高效液相色谱-串联质谱法(LC/MS/MS)测定纺织品中致癌芳香胺的检测方法.纺织品中的偶氮染料在柠檬酸缓冲液中用连二亚硫酸钠还原为芳香胺,用硅藻土提取还原液中的芳香胺,用乙醚洗脱,浓缩至近干后用甲醇定容.使用液相色谱-串联质谱进行测定,色谱柱为XTerra MS C18柱,流动相为甲醇和0.025 mol/L乙...     

Characterization of sulfonated azo dyes and aromatic amines by pyrolysis gas chromatography/mass spectrometry

Sixteen sulfonated and unsulfonated azo dyes as well as eleven sulfonated and unsulfonated aromatic amines were analyzed and qualitatively characterized by means of pyrolysis gas chromatography/mass spectrometry at different temperatures. Aniline and aminonaphthalene were found to be the dominant pyrolysis products of sulfonated aromatic amines and dyes. Azo dye and dye class specific key compounds such as benzidine, vinyl-p-base and 4-aminoazobenzene could be identified by pyrolysis gas chromatography/mass spectrometry of commercial acid, cationic, direct, reactive and solvent dyes. 500 degrees C was the optimal pyrolysis temperature for most of the pyrolyzed compounds. The method was applied to a dried sample of a textile wastewater concentrate from a dyeing process. Reactive azo dyes of the group of Remazol dyes and anthraquinone dyes could be identified as the major compounds of the sample. The finding of caprolactam (a printing additive) suggests that the wastewater contained effluent from a process of heat-activated printing with reactive dyes. p-Chloraniline, a banned aromatic amine, was identified. Chemical reduction of the wastewater sample prior to pyrolysis resulted in the release of volatile aromatic amines and aided the classification of several products of pyrolysis.     

Determination of 14 heterocyclic aromatic amines in meat products using solid‐phase extraction and supercritical fluid chromatography coupled to triple quadrupole mass spectrometry

A novel, simple, and sensitive method has been developed for simultaneous determination of 14 heterocyclic aromatic amines in meat product using solid‐phase extraction combined with ultrahigh‐performance supercritical fluid chromatography coupled to tandem quadrupole mass spectrometry. The analytes could be separated within 7 min and identified using their retention times and mass. The developed method was validated based on the linearity, limits of quantification, precision, and accuracy. The recovery ranged from 52.3 to 97.5% with an acceptable standard deviation, which is not higher than 6%. The limits of quantitation ranged from 0.03 to 0.17 µg/kg. The selectivity and sensitivity were satisfactory in multiple reaction monitoring mode. The method was applied to commercial meat products, and the results demonstrated that the novel method has potential for the analysis of the targets in food matrices. This is the first work reporting the simultaneous quantification of 14 heterocyclic aromatic amines by means of ultrahigh‐performance supercritical fluid chromatography coupled to tandem quadrupole mass spectrometry.     

Investigation of hexabromocyclododecane thermal degradation pathways by gas chromatography/mass spectrometry

The decomposition products of hexabromocyclododecane (HBCD), a widely used brominated flame retardant, were investigated by gas chromatography/mass spectrometry (GC/MS). HBCD thermal degradation was conducted under a moderate heating rate (10 degrees C/min) in a batch reactor using both inert and oxidizing atmospheres. GC/MS analysis allowed the identification of substances derived from the primary pyrolysis process at the moderate heating rates used. The presence of oxygen seems to have a negligible influence on the degradation products obtained in HBCD decomposition, at least at moderate heating rates. Based on the identified products, the main pathways of HBCD thermal degradation were assessed and a mechanism for HBCD decomposition was proposed. The results obtained indicate that hexa-, penta- and tetrabrominated polyaromatic structures seem not to be primary products of HBCD decomposition, and may only be obtained by secondary bromination reactions.     

Simultaneous determination of amphetamines and ketamines in urine by gas chromatography/mass spectrometry

A method for the simultaneous determination of amphetamines and ketamines (ketamine, norketamine and dehydronorketamine) in urine samples by gas chromatography/mass spectrometry was developed and validated. Urine samples were extracted with organic solvent and derivatized with trifluoroacetic anhydride (TFAA). The limits of detection and limits of quantification for each analyte were lower than 19 and 30 ng/mL, respectively. Within-day and between-day precisions were within 0.5% and 10.6%, respectively. Biases for three levels of control samples were within -10.6% and +7.8%. The concentration of dehydronorketamine was greater than those of ketamine or norketamine in 19 of 35 ketamine-positive samples. A group of 110 human urine samples previously determined to contain at least one of the target analytes was analyzed using the new method, and excellent agreement was observed with previous results.     

Liquid chromatographic determination of lumacaftor in the presence of ivacaftor and identification of five novel degradation products using high-performance liquid chromatography ion trap time-of-flight mass spectrometry

Lumacaftor is a transmembrane conductance regulator potentiator drug, prescribed for the treatment of cystic fibrosis in patients who are homozygous for the F508del mutation. Quantitation of lumacaftor besides its degradation products and ivacaftor was achieved on a fused-core silica particle column packed with pentafluorophenylpropyl stationary phase (Ascentis Express F5, 2.7 μm particle size 100 mm × 4.6 mm; Supelco) using gradient elution (A: 0.1% [v/v] formic acid in water, B: 0.1% [v/v] formic acid in acetonitrile [the mobile phase pH 2.5]). A constant flow rate at 1 mL/min was applied, and the detection was realized using a photodiode array detector set at 216 nm. The pseudo tablet formulation of the lumacaftor/ivacaftor fixed-dose combination preparation, namely, Orkambi®, was prepared in vitro and used for the analytical performance validation and method application studies. In addition, five novel degradation products, four of which even have no Chemical Abstracts Services registry number, were identified using high-resolution mass spectrometry instrument, and their possible mechanisms of formation were proposed. According to current literature, this paper can be regarded as the most comprehensive liquid chromatographic study on lumacaftor determination, among its counterparts.     

Liquid chromatography/mass spectrometric studies on atorvastatin and its stress degradation products

A comprehensive mass fragmentation pathway of atorvastatin, which has not been reported so far, was established by subjecting the drug to multi-stage mass spectrometric (MSn) studies. It was used along with liquid chromatography/mass spectrometric (LC/MS) and liquid chromatography/time-of-flight mass spectrometric (LC/TOFMS) analyses to identify the drug degradation products formed under stress conditions of hydrolysis, oxidation and photolysis. Other than lactone, which is a reported hydrolysis product, six unknown hydrolytic products could be identified, viz., dehydrated drug, dehydrated drug lactone, and diastereomers of the drug, drug lactone, dehydrated drug, and dehydrated drug lactone. Among the two products separated under oxidative conditions, one was lactone, again formed as a result of drug hydrolysis in an acidic environment of peroxide solution. The other was similar to a reported oxidative product. Under photolytic conditions in solution, one new product could be identified, while most of the others matched with those known from the literature. Hence overall a more complete degradation pathway of the drug was established than known at present, by using a stress testing approach and employing LC/MS techniques.     

Liquid chromatography coupled to tandem mass spectrometry for the analysis of acrylamide in typical Spanish products

This paper describes the use of liquid chromatography coupled to tandem mass spectrometry for the determination of acrylamide in several typical foods produced and consumed in Spain. Christmas sweets, olives, traditionally made potato crisps, pastry products, sweet fritters ("churros") and one of Spain's most famous dishes, Spanish omelette, were selected. Using the mass spectra information provided by an ion trap analyzer in combination with the accurate mass measurements from time-of-flight (TOF) spectrometry a co-extractive interference present in some potato products was identified as valine. A porous graphitic carbon column, which enabled the co-extractive and acrylamide to be separated, and ion trap or triple quadrupole analyzers, depending on the acrylamide concentration, were used to determine this genotoxic compound in foodstuffs. The highest values were found in potato products, sweet fritters, Christmas sweets and pastry products, with values ranging between 70 and 2000 microg/g. Spanish omelette presented relatively low levels, similar to those obtained for dried fruits.     

Quantitative determination of the beta-adrenoceptor stimulant formoterol in urine by gas chromatography mass spectrometry

A method for the quantitative determination of the beta-stimulant formoterol in urine, using a gas chromatograph--mass spectrometer, is described. Formoterol can be analyzed after the addition of a deuterium-labelled internal standard and conversion to a mixed bis-pentafluoropropionyl-methyl derivative for selected ion monitoring. The detection limit was 5 ng/ml. Urinalysis after the oral administration of formoterol fumarate, using a combined enzymic hydrolysis method, revealed that the drug was conjugated with glucuronic acid in rats, dogs and humans.