The effect of cation nonstoichiometry on the electrical conductivity of acceptor-doped CaZrO3

The electrical properties of acceptor-doped Ca_1−xZr_0.99M_0.01O_3−δ (M = Mg²⁺, In³⁺) systems were investigated as a function of cation nonstoichiometry (0 ≤ x ≤ 0.05). The characterization was carried out using the impedance spectroscopy between 550 °C and 1100 °C in dry air. The contributions of the grain and grain boundary conductivity to the total conductivity were obtained from the impedance data. When the Ca deficiency (x) increased, the total conductivity rapidly decreased with the corresponding increase in activation energy. Although the grain conductivity increased slightly with increasing x, the total conductivity is mostly determined by the highly resistive grain boundary. With varying x, the activation energy of total conductivity showed the percolation behavior. The percolation threshold values vary according to the doped species. It may be due to the difference in concentration of oxygen vacancies of the specimens.     

Structure and relaxor behavior of BaBi4Ti4−xZrxO15 ceramics

BaBi₄Ti_4−xZr_xO₁₅ with x = 0.1, 0.2, 0.3 and 0.5, has been synthesized via modified solid state reaction route. X-ray diffraction studies confirmed the formation of single phase Zr⁴⁺ substituted BaBi₄Ti₄O₁₅ up to x = 0.2. ZrO₂ and Bi₂O₃ based impurity phases were found at x = 0.3 and 0.5 substitutions. However, Rietveld refinement showed the increase in lattice parameters of BaBi₄Ti₄O₁₅ up to x = 0.5 substitutions. A broad dielectric peak associated with frequency dependence dielectric maximum temperature was observed at low substitutions. Relaxor behavior was suppressed at x = 0.5 substitution. A broadening and shifting of permittivity-temperature peak was found for the substitution. The high temperature slopes of dielectric peaks were analyzed by quadratic law for relaxors. The degree of relaxation and phase transformation diffusiveness were investigated at different substitutions.     

Electrical conductivity,optical properties and mechanical stability of 3, 4, 9, 10-perylenetetracarboxylic dianhidride based organic semiconductor

The 3, 4, 9, 10-perylenetetracarboxylic dianhydride (PTCDA) doped polymer films were prepared with Polypyrrole (PPy) and Polyvinyl alcohol (PVA) polymers by solution-casting. The change in structure and chemical composition of samples was identified by XRD and FTIR respectively. The UV–visible spectroscopy demonstrates the optical characteristics and band gap properties of sample. The homogeneous morphology of sample for higher wt% of PTCDA was examined by atomic force microscopy (AFM). The differential scanning calorimetry (DSC) results demonstrate the decrease in melting temperature (T_m) and degree of crystallinity (χ_c%) of polymeric organic semiconductor. The mechanical property demonstrates the high tensile strength and improved plasticity nature. Impedance spectroscopy was evaluated to determine the conductivity response of polymeric organic semiconductor. The highest DC conductivity (2.08×10⁻³ S/m) was obtained for 10 wt% of PTCDA at 140 °C. The decrease in activation energy (E_a) represents the non-Debye process and was evaluated from the slope of ln σ_dc vs. 10³/T plot.     

Structure and conductivity investigations of alkaline earth substituted uranium oxide,U1 − xMxO2 ± δ (M = Mg,Ca, Sr) for solid oxide fuel cell applications

Alkaline earth substituted UO₂ (U_1 − xM_xO_2 ± δ; M = Mg, Ca, Sr; 0.1 ≤ x ≤ 0.525) with fluorite structure was synthesized in reducing atmosphere. Structure and conductivity properties of U_1 − xM_xO_2 ± δ fluorites were investigated for possible application in solid oxide fuel cells (SOFC). At room temperature and ambient atmosphere the materials are stable; however they decompose at an oxygen partial pressure p_O2 > 10^− 4 atm and temperatures higher than 600 °C. The total conductivity measured for the best conducting U_1 − xM_xO_2 ± δ material with M = Ca and x = 0.177 is as high as 3 S/cm at p_O2 < 10^− 4 atm at 600 °C. The relatively low ionic transference number (t_i∼0.02) is disadvantageous for potential use as electrolyte material for SOFC applications. The high conductivity and possible depolarization effects suggest potential use as anode materials in SOFC.     

High ionic conductive behavior of cyanoethylated polyvinylalcohol- and polyacrylonitrile-based electrolytes

New type polymer electrolyte films based on poly(acrylonitrile), (PAN), and cyanoethylated poly(vinyl alcohol), (CN-PVA), were prepared and their conducting behaviors were investigated. CN-PVA was prepared from poly(vinyl alcohol), (PVA) and acrylonitrile in the presence of sodium hydroxide and quaternary ammonium halide as a phase transfer catalyst. Free standing PAN- and CN-PVA-based electrolyte films were prepared by casting the propylene carbonate (PC) solution containing PAN, CN-PVA and LiClO₄ and removing some amount of PC. Ionic conductivity of the electrolyte film, (PAN)10(CN-PVA) 10(LiClO₄)8(PC)4 composite film was 14.6 mS cm^− 1 at 30 °C and 22.4 mS cm^− 1 at 60 °C. FTIR results for the electrolyte films suggest that the nitrile groups in the CN-PVA matrix mainly interact with the lithium ions in the films and enhance dissolution of the lithium salt in the electrolyte films.     

Conductivity and thermal studies of blend polymer electrolytes based on PVAc–PMMA

The polymer electrolytes comprising blend of poly(vinyl acetate) (PVAc) and poly(methylmethacrylate) (PMMA) as a host polymer and LiClO₄ as a dopant are prepared by solution casting technique. The amorphous nature of the polymer–salt complex has been confirmed by XRD analysis. The DSC thermograms show two T_g's for PVAc–PMMA blend. A decrease in T_g with the LiClO₄ content reveals the increase of segmental motion. Conductance spectra results are found to obey the Jonscher's power law and the maximum dc conductivity value is found to be 1.76 × 10^− 3 S cm^− 1 at 303 K for the blend polymer complex with 20 wt.% LiClO₄, which is suitable for the Li rechargeable batteries. The conductivity–temperature plots are found to follow an Arrhenius nature. The dc conductivity is found to increase with increase of salt concentration in the blend polymer complexes.     

Structure,dielectric and optical properties of p-type (PVA/CuI) nanocomposite polymer electrolyte for photovoltaic cells

A novel PVA/CuI nanocomposite polymer electrolyte layer synthesized via the reduction of CuCl₂ by NaI in an aqueous PVA solution. The as-prepared films were characterized by X-ray diffraction, scanning electron microscope, as well as impedance spectroscopy. The obtained results indicated the formation of hexagonal CuI nano particles of ≈55 nm sizes embedded in the PVA matrix. In addition, the study of dielectric parameters and conductivity of PVA/CuI nanocomposite in wide range of temperature and frequency are given and discussed. The frequency dependence of ac-conductivity suggests power law with an exponent 0.026 < s < 0.73 which predicts hopping of charge carriers. The bulk conductivity showed activation with temperature, significant values of activation energy are deduced and discussed. An average value of the energy gap width, 2.05 eV obtained using optical absorption in UV–visible spectra for PVA/CuI nanocomposite polymer electrolyte.     

Radiation stability of M1 − xPrxF2 + x (M = Ca,Sr, Ba) crystals

The radiation stability of the mixed crystals M_1 ? xR_xF_2 + x (M = Ca, Sr, Ba) depends on types of the alkaline-earth and rare-earth ions. Different to Eu- and Ce-containing systems, M_1 ? xPr_xF_2 + x solid solutions have a low radiation resistance, which may be associated with hole trapping on praseodymium ion according to the reaction Pr³⁺ → Pr⁴⁺ which is typical for praseodymium. The coloration efficiency of M_1 ? xPr_xF_2 + x crystals grows in the row Ca → Sr → Ba, which is explained satisfactorily within the model of rare-earth clusters, the structure of which is determined by the ratio of the base alkaline-earth cation to the praseodymium ion radii.     

Reduction of thin-film ceria on Pt(111) by supported Pd nanoparticles probed with resonant photoemission

Local defects present in CeO_2 ? x films result in a mixture of Ce³⁺ and Ce⁴⁺ oxidation states. Previous studies of the Ce 3d region with XPS have shown that depositing metal nanoparticles on ceria films causes further reduction, with an increase in Ce³⁺ concentration. Here, we compare the use of XPS and resonant photoemission spectroscopy (RESPES) to estimate the concentration of Ce³⁺ and Ce⁴⁺ in CeO_2 ? x films grown on Pt (111), and the variation of this concentration as a function of Pd deposition. Due to the nature of the electronic structure of CeO_2 ? x, resonant peaks are observed for the 4d–4f transitions when the photon energy matches the resonant energy; (hν = 121.0 eV) for Ce³⁺ and (hν = 124.5 eV) for Ce⁴⁺. This results in two discrete resonant photoemission peaks in valence band spectra. The ratio of the difference of these peaks with off-resonance scans gives an indication of the relative contribution of Ce³⁺. Results from RESPES indicate reduction of CeO_2 ? x on deposition of Pd, confirming earlier findings from XPS studies.     

Oxygen non-stoichiometry and electrical conductivity of Pr2−xSrxNiO4±δ with x = 0–0.5

Oxygen non-stoichiometry and electrical conductivity of the Pr_2−xSr_xNiO_4±δ series with x = 0.0–0.5 were investigated in Ar/O₂ (pO₂ = 2.5 to 21 000 Pa) within a temperature range of 20–1000 °C. The equilibrium values of oxygen non-stoichiometry and electrical conductivity of these nickelates were determined as functions of temperature and oxygen partial pressure (pO₂). The nickelates with x = 0–0.5 appear to be p-type semiconductors in the investigated temperature and pO₂ ranges. The nickelates with x = 0.3–0.5 show very feebly marked pO₂ dependencies of the conductivity. Pr_1.7Sr_0.3NiO_4±δ shows the anomalies of the conductivity versus oxygen partial pressure which can be related to the orthorhombic–tetragonal crystal structure transformations. The conductivity of the Pr_2−xSr_xNiO_4±δ samples correlates with the average oxidation state of the nickel cations. The samples with x = 0.5 have the highest nickel oxidation state (≈ 2.5+), the highest [Ni³⁺]/[Ni²⁺] ratio close to 1 and show the highest conductivity (≈ 120 S/cm) in the whole pO₂ and temperature ranges investigated.     

Mixed conducting perovskite-like ceramics on the base of lanthanum gallate

Ceramic perovskite solid solutions (La_0.9Sr_0.1)[(Ga_1−xM_x)_0.8Mg_0.2]O_3−y, 0 ≤ x ≤ 0.5, M = Fe, Ni, Cr (systems I–III) and brownmillerite solid solutions (La_0.2Sr_1.8)[Ga(Fe_1−xMg_x)]O_5−z, 0 ≤ x ≤ 0.5, (system IV) have been prepared. The samples have been studied by X-ray diffraction and electron microscopy methods, dielectric spectroscopy and permeability measurements. The correlation between the composition, unit cell parameter changes, electrical transport and oxygen permeation properties has been revealed. Introduction of transition metals (Fe, Ni, or Cr), substituting for gallium, ensures the enhancement of the electronic constituent of the conductivity in the perovskite systems I–III. Stabilization of the transition metal high valence states 4+ or 5+ has been suggested for compositions I and III. This leads to a unit cell volume contraction and provides a decrease in the concentration of oxygen vacancies. The oxygen permeability reaches its maximum values in compositions I–III with x ∼ 0.3. On the contrary, increasing concentration of the doping element with lower valence state (magnesium), substituting for iron, determines the expansion of the brownmillerite unit cell volume and provides an increase of the oxygen vacancy concentration, which in turn, favors the enhancement of oxygen permeability of composition IV.     

Effect of rare-earth donor Ce3+ doping at A-site of PLSZNT on dielectric and piezoelectric properties

Dielectric and piezoelectric properties of [Pb_0.976La_0.014−xCe_xSr_0.01][Zr_0.57Ti_0.43]_{(0.9975−((0.014−x)/4)−(x/4))}Nb_0.002O₃ (PLCSZNT) ceramic compositions for 0 ⩽ x ⩽ 1 mol% were investigated. The XRD analysis showed the presence of single rhombohedral phase. Grain size and density increased until 0.6 mol% Ce and further Ce concentration inhibited the grain growth. The stability of rhombohedral phase has been supported by tolerance factor and average electronegativity difference. The room temperature dielectric response (ε_RT) increased up to 0.6 mol% combined with a significantly reduced dielectric loss (Tan δ) and low Curie temperature (T_c). The higher piezoelectric properties associated with low Ce concentration are attributed to rhombohedral phase. The optimum dielectric and piezoelectric properties were found in 0.6 mol% Ce composition which could be suitable for possible piezoelectric applications.     

Effects of PVA organic binder on electric properties of CaCu3Ti4O12 ceramics

CaCu₃Ti₄O₁₂ ceramics with incorporation of polyvinyl alcohol (PVA) are prepared from the powder synthesized by a solid state reaction. Their electric and dielectric properties are investigated in this study. It is found that adding PVA can dramatically reduce the dielectric loss of CCTO in the low frequency region, and stabilize the dependence of dielectric constant on the measuring frequency. The minimum dielectric loss of 0.045 is obtained from the sample with 8 wt% PVA. The nonlinear coefficient (α) and breakdown electric field (E_b) increase with an increase of PVA binder.     

Current transport mechanism and photovoltaic properties of photoelectrochemical cells of ITO/TiO2/PVC–LiClO4/graphite

This paper deals with the current transport mechanism of solid state photoelectrochemical cells of ITO/TiO₂/PVC–LiClO₄/graphite as well as the physical properties of a component of a device affecting its performance. The principle of operation and a schematic energy level diagram for the materials used in the photoelectrochemical cells are presented. The device makes use of ITO films, TiO₂ films, PVC–LiClO₄ and graphite films as photoanode, photovoltaic material, solid electrolyte and counter electrode, respectively. The device shows rectification. The J_sc and V_oc obtained at 100 mW cm⁻² were 0.95 μAcm⁻² and 180 mV, respectively.     

NMR and electric impedance study of lithium mobility in fast ion conductors LiTi2 − xZrx(PO4)3 (0 ≤ x ≤ 2)

Materials of the LiTi_2 − xZr_x(PO₄)₃ series (0 ≤ x ≤ 2) were prepared and characterized by powder X-ray (XRD) and neutron diffraction (ND), ⁷Li and ³¹P Nuclear Magnetic Resonance (NMR) and Electric Impedance techniques. In samples with x < 1.8, XRD patterns were indexed with the rhombohedral R3̅c space group, but in samples with x ≥ 1.8, XRD patterns display the presence of rhombohedral and triclinic phases. The Rietveld analysis of the LiTi_1.4Zr_0.6(PO₄)₃ neutron diffraction (ND) pattern provided structural information about intermediate compositions. For low Zr contents, compositions deduced from ³¹P MAS-NMR spectra are similar to nominal ones, indicating that Zr⁴⁺ and Ti⁴⁺ cations are randomly distributed in the NASICON structure. At increasing Zr contents, differences between nominal and deduced compositions become significant, indicating some Zr segregation in the triclinic phase. The substitution of Ti⁴⁺ by Zr⁴⁺ stabilizes the rhombohedral phase; however, electrical performances are not improved in expanded networks of Zr-rich samples. Below 300 K, activation energy of all samples is near 0.36 eV; however, above 300 K, activation energy is near 0.23 eV in Ti-rich samples and close to 0.36 eV in Zr-rich samples. The analysis of electrical data suggests that the amount of charge carriers and entropic terms are higher in Zr-rich samples; however, the increment of both parameters does not compensate lower activation energy terms of these samples. As a consequence of different contributions, the bulk conductivity of Zr-rich samples, measured at room temperature, is one order of magnitude lower than that measured in Ti-rich samples.     

The effect of copper concentration on structural,optical and dielectric properties of CuxZn1 − xS thin films

Cu_xZn_1 ? xS (x = 0, 0.25, 0.50, 0.75, 1) thin films were deposited on glass substrates using Successive Ionic Layer Adsorption and Reaction (SILAR) method at room temperature and ambient pressure. The copper concentration (x) effect on the structural, morphological and optical properties of Cu_xZn_1 ? xS thin films was investigated. The X-ray diffraction (XRD) and scanning electron microscopy (SEM) studies showed that all the films exhibit polycrystalline nature and are covered well with glass substrates. The crystalline and surface properties of the films improved with increasing copper concentration. The energy bandgap values were changed from 2.07 to 3.67 eV depending on the copper concentration. The refractive index (n), optical static and high frequency dielectric constants (ε_o, ε_∞) values were calculated by using the energy bandgap values as a function of the copper concentration.     

The studies on structural and thermal properties of delithiated LixNi1/3Co1/3Mn1/3O2 (0 < x ≤ 1) as a cathode material in lithium ion batteries

The structural and thermal properties of the delithiated Li_xNi_1/3Co_1/3Mn_1/3O₂ (0 < x ≤ 1) material have been investigated by using diffraction and thermoanalytical techniques such as XRD and TG-DSC methods. XRD result shows that the delithiated materials maintain the O3-type structure with defined stoichiometric number at the range of 0.24 < x ≤ 1, exhibiting good crystal structural stability. The cobalt and nickel ions in the delithiated materials change their valence state (i.e. Co³⁺ to Co⁴⁺ and Ni³⁺ to Ni⁴⁺) when x < 0.49; the irreversible changes of the transformation may affect the first cycle of charge–discharge efficiency of the materials. A comparison of the results of TG-DSC with TPD-MS shows that the irreversible change of oxygen species during the delithiation process of Li_xNi_1/3Co_1/3Mn_1/3O₂ have great influence on the structural and thermal stability and reversibility of the materials.     

Aqueous polymer–nitrate solution deposition of YBCO films

High critical current density YBa₂Cu₃O_7?x (YBCO) films were prepared by solution deposition of aqueous non-fluorine precursors. Non-fluorine polymer-assisted deposition (PAD) processes utilizing rheology modifiers and chelating agents were used to produce 50 nm films with a critical current density (J_c) over 3 MA/cm² and 400 nm films with J_c > 1 MA/cm²_. T_c measurements indicated that films have T_c values near 90 K. The total heat treatment time to produce these high performance films was less than 4 h. Rheology modifiers such as polyvinyl alcohol (PVA) and hydroxyethyl cellulose (HEC) were used to increase the thickness of deposited films independent of the solution cation concentration. Chelating agents such as polyethylene glycol (PEG) and sucrose increased the barium ion solubility. Nitrate crystallization during deposition was controlled through rapid drying with vacuum and coating with hot solutions.     

Electronic property and structure of double-doping Y1−2xPrxCaxBa2Cu3O7−δ with 0 ⩽ x ⩽ 0.14

Equal amount Pr and Ca double-doping Y_1?2xPr_xCa_xBa₂Cu₃O_7?δ with 0 ? x ? 0.14 have been investigated by X-ray diffraction, resistivity, and X-ray photoemission spectroscopy (XPS). The deviation of the linearly decreasing of T_c vs. x curve was observed when x < 0.10. The resistivity and the temperature coefficient of resistivity also exhibit abnormal behaviors around x = 0.10. It is revealed that the conductivity behavior of Y_1?2xPr_xCa_xBa₂Cu₃O_7?δ with low Pr content (x < 0.10) is different from that of the relative high Pr content (x > 0.10), which suggests a change of Pr valence with the Pr content. XPS measurement shows that the relative amount of Pr³⁺ and Pr⁴⁺ is closely related to the total Pr content x. The valence of Pr is close to +3 when x < 0.10 and increases towards +4 when x > 0.10, which implies a different mechanism for depression of superconductivity of Pr content x < 0.10 from that of Pr content x > 0.10 in Pr doping Y-123.     

Thin films of molecule-based charge transfer complex cobalt tetracyanoethylene: In situ X-ray photoemission study

Thin films of molecule-based charge transfer magnet, cobalt tetracyanoethylene [Co(TCNE)_x, x ~ 2] consisting of the transition metal Co, and an organic molecule viz. tetracyanoethylene (TCNE) have been deposited by using physical vapor deposition method under ultra-high vacuum conditions at room temperature. X-ray photoelectron spectroscopy (XPS) technique has been used extensively to investigate the electronic properties of the Co(TCNE)_x thin films. The XPS measurements show that the prepared Co(TCNE)_x films are clean, and oxygen free. The stoichiometries of the films, based on atomic sensitive factors, are obtained, and yields a ~ 1:2 ratio between metal Co and TCNE for all films. Interestingly, the positive shift of binding energy position for Co(2p), and negative shifts for C(1s) and N(1s) peaks suggest a charge-transfer from Co to TCNE, and cobalt is assigned to its Co(II) valence state. In the valence band investigation, the highest occupied molecular orbital (HOMO) of Co(TCNE)_x is found to be at ~ 2.4 eV with respect to the Fermi level, and it is derived either from the TCNE^? singly occupied molecular orbital (SOMO) or Co(3d) states. The peaks located at ~ 6.8 eV and ~ 8.8 eV are due to TCNE derived electronic states. The obtained core level and valence band results of Co(TCNE)_x, films are compared with those of V(TCNE)_x thin film magnet: a well known system of M(TCNE)_x type of organic magnet, and important points regarding their electronic properties have been brought out.