巯基功能化膨润土吸附Pb2+的动力学和热力学研究

研究了自制巯基功能化膨润土(TFB)对Pb2+的吸附行为,考察了溶液的pH值、离子强度、吸附时间和温度对吸附平衡的影响,并对吸附过程进行了动力学与热力学研究.结果表明,常温下,吸附时间为60min、0.1mol/L的KNO3、pH=6.0、5.0g/L TFB对200mg/L的Pb2+的吸附率达到85.4％以上,TFB对Pb2+的吸附动力学符合准二级动力学方程;TFB对Pb2+的吸附热力学符合Langmuir等温线方程和Dubinin-Radushkevich (D-R)等温线方程,表明吸附主要发生在TFB表面的活性区域,属于单分子层吸附,其吸附平均活化能E在8-16kJ/mol范围内,表明该吸附过程为化学吸附,不同温度下的吸附热力学的吉布斯自由能以及熵变和焓变表明该吸附过程为自发放热反应.     

钠基膨润土吸附亚甲基蓝热力学与动力学研究

利用钠基膨润土吸附亚甲基蓝水溶液,探讨了不同参数如接触时间、初始pH值、温度等对其吸附性能的影响。结果表明,室温下,pH10,钠基膨润土吸附60min,其吸附量达198.71mg/g,且吸附量随温度的升高而增大。通过计算不同温度下的热力学参数?G,?H和?S,证实该吸附为一自发的吸热过程。其等温吸附平衡更符合Langmuir模型;吸附动力学更适合准二级反应方程。     

阳离子膨润土对分散染料的吸附动力学研究

研究了阳离子膨润土(EPI-DMA/Bt, PD/Bt, CTMAB/Bt)对分散染料(分散黄棕S-2RFL, 分散大红S-R, 分散蓝SBL, 分散黄SE-6GFL)的吸附动力学行为. 结果表明, 阳离子膨润土对分散染料的吸附过程符合二阶段吸附速率方程, 各阶段具有不同的吸附动力学常数(k1, k2)以及吸附活化能(Ea1, Ea2)、活化焓(ΔH*1, ΔH*2)和活化熵(ΔS*1, ΔS*2); 在阳离子膨润土对分散染料的吸附过程中, k1随着阳离子插层剂烷烃链的增加而增大, 表明较大的晶片层间距, 疏水的层间域和表面正电荷增加均有利于吸附速率增大; 对于两个吸附动力学阶段, ΔH★1<-TavΔS★1, △H★2<-TavΔS★2和ΔG★>0表明整个吸附过程活化熵的影响大于活化焓.     

有机改性膨润土对水中钙黄绿素的吸附性能

在微波作用下用十六烷基溴化吡啶(CPB)、十六烷基三甲基溴化铵(CTMAB)和盐酸萘乙二胺(NETH)对天然膨润土进行改性,制得了CPB-膨润土(CPB-Bt)、CTMAB-膨润土(CTMAB-Bt)和NETH-膨润土(NETH-Bt),并比较了它们对水中钙黄绿素的吸附性能.结果表明,在钙黄绿素浓度25 mg·L-1、...     

离子交换树脂吸附胞嘧啶核苷三磷酸的动力学和热力学研究

根据CTP在离子交换树脂上的吸附容量和分离因数的大小,确定Duolite A-30树脂适合CTP与CDP及CMP之间的分离.CTP在Duolite A-30树脂上的吸附动力学和热力学研究表明,在283.15～303.15K之间,CTP的质量浓度在7.5g/L以上时,Duolite A-30树脂对CTP的吸附主要受颗粒扩散的控制,其有效扩散系数为D=3.47×10-7cm2/s,溶液的质量浓度≤1.0g/L时,CTP与Duolitc A-30树脂之间的交换速率主要受液膜控制,其液膜扩散系数为Kf=4.112×10-4/s.热力学参数Eα=9.008kJ/mol,△H=5.17kJ/mol·K,△S283.15K=80.28J/mol·K.     

十六烷基三甲基溴化铵改性膨润土对直接黑染料的吸附及机理

用十六烷基三甲基溴化铵改性膨润土(有机膨润土),用红外光谱和固体紫外漫反射光谱等对有机膨润土的结构进行了分析。研究了有机膨润土对水中直接黑染料的吸附和机理。用0.05g有机膨润土处理浓度为70mg/L的直接黑溶液时(303K),脱色率达到72.6%,平衡吸附量为20.5mg/g,有机膨润土对直接黑染料的吸附符合Freundlich吸附等温方程,从热力学结果来看,是化学吸附和物理吸附共同作用的过程。     

介孔碳CMK-3对苯酚的吸附动力学和热力学研究

研究了介孔碳CMK-3对苯酚的吸附性能, 与传统商用活性碳(CAC)进行了比较, 结果表明, CMK-3比CAC的吸附量大、吸附速率快、达到平衡时间短, 是一种较好的吸附剂. 同时探讨了介孔碳CMK-3对苯酚的吸附热力学和动力学特征. CMK-3对苯酚的吸附行为可用Langmuir和Freundlich等温式进行描述, 相关性都较好, 但更符合Freundlich经验公式. 分别采用模拟一阶反应和二阶反应模型考察了吸附动力学, 并计算了这些动力学模型的速率常数. 模拟二级反应模型和实验数据之间有较好的相关性. 分别计算了热力学参数ΔG0, ΔS0和ΔH0, 结果表明, CMK-3对苯酚的吸附过程是吸热和自发的.     

有机膨润土吸附水中重金属和有机污染物的性能及机理研究

螯合剂柱撑有机膨润土IMB-TMA-Am能有效吸附水中有机物对硝基苯酚(PNP)和重金属离子Cu2 ,其中IMB为内蒙膨润土;CTMA为溴化十六烷基三甲基季铵盐阳离子;Am分别为有机螯合剂乙二胺(En)、三乙烯四胺(TETA)和四乙烯五胺(TEPA)。实验结果表明:螯合剂柱撑有机膨润土对有机污染物的吸附主要表现为有机物在长碳链疏水介质中的分配,其吸附能力和膨润土内有机碳、氮含量一致;对水中重金属离子的吸附机理是Cu2 和进入膨润土层间的有机螫合剂Am形成了配合物,其吸附能力和所形成配合物的稳定性一致。     

有机膨润土的吸附性能研究

有机膨润土处理水中有机物的研究已有报道［1－4］，但尚无就改性所用的表面活性剂对有机膨润土吸附性能的影响及规律的系统研究，对有机膨润土与不同有机物间作用机理的报道也甚少［1］．本文用3种不同的阳离子表面活性剂改性膨润土，并从等温吸附线的特征和有机物的辛醇－水分配系数较系统地研究了有机膨润上对几种有机物的吸附性能和作用机理．1实验部分1．1材料原士为钠基膨润土，经测定其阳离子交换容量为7464meg／100g土；澳化十六烷基王甲铰（CTMAB）为分析纯，溪化十二烷基三甲铰（DTMAB，95％），演化十八烷基三甲按（OTMAB…     

Characterization and determination of the thermodynamic and kinetic properties of p-CP adsorption onto organophilic bentonite from aqueous solution

The characterization of tetraethylammonium bentonite and the adsorption of p-chlorophenol (p-CP) onto organophilic bentonite (tetraethylammonium bentonite) was studied as a function of the solution concentration and temperature. The observed adsorption rates were found to fit first-order kinetics. The rate constants were calculated for temperatures ranging between 15.0 and 35.0 degrees C at constant concentration. The adsorption energy E and adsorption capacity q(m) for the phenolic compound adsorbing on organophilic bentonite were estimated using the Dubinin-Radushkevic equation. Thermodynamic parameters (Deltag(a), Deltah(a), Deltas(a)) were calculated by a new approximation from the isotherms of p-CP adsorption on organophilic bentonite. These isotherms were modeled according to Freundlich and Dubinin-Radushkevic adsorption isotherms. The amount of adsorption of p-chlorophenol on organophilic bentonite was found to be dependent on the relative energies of adsorbent-adsorbate, adsorbate-solvent, and adsorbate-adsorbate interactions.     

氨基功能化离子印迹硅胶对Cd2 的吸附行为及机理

研究了氨基功能化离子印迹硅胶对Cd2+的吸附行为及机理,进行了等温吸附模型和吸附动力学的测定和吸附热力学计算。结果表明,饱和吸附量的实验值为30.7mg/g;20min即可达到吸附平衡;等温吸附曲线符合Langmuir等温吸附模型,吸附过程以单层吸附为主;Cd2+的吸附动力学数据均符合准二级反应动力学模型;反应的吉布斯自由能为负值,焓变为23.01k J/mol,熵变为104.1J/mol·K,说明吸附是一个吸热的自发进行的过程。     

Thermodynamic and kinetic characterization of a bridged-ethylene hybrid C18 stationary phase

In this study, a series of polycyclic aromatic hydrocarbons (PAHs) and nitrogen-containing polycyclic aromatic hydrocarbons (NPAHs) is separated on a hybrid stationary phase using methanol and acetonitrile mobile phases. Temperature is varied from 283 to 313 K in order to determine thermodynamic and kinetic parameters of the separation. Thermodynamic behavior is characterized by the retention factor and associated changes in molar enthalpy, whereas kinetic behavior is characterized by the rate constants and associated activation energies. In this study, the retention factors for the NPAHs are smaller than those for the parent PAHs in methanol, while they are more similar to the parent PAHs in acetonitrile. The changes in molar enthalpy are very similar for all solutes, yet are more negative in acetonitrile than in methanol. The rate constants for the NPAHs are smaller than those for their parent PAHs in both mobile phases. Moreover, the rate constants in acetonitrile are one to four orders of magnitude smaller than those in methanol. Based on these thermodynamic and kinetic results, the hybrid stationary phase is compared to traditional silica stationary phases. In addition, the relative contributions from the partition and adsorption mechanisms are discussed.     

纳米TiO_2对去除水溶液中硒的吸附性能研究

研究了纳米TiO_2对Se(Ⅳ)的吸附行为,考察了不同吸附材料、吸附剂用量、溶液pH、吸附时间、温度等因素对吸附作用的影响.结果表明,纳米TiO_2对Se(Ⅳ)的吸附在3min基本达到平衡;pH为5.0时,Se(Ⅳ)可被纳米TiO_2定量吸附,吸附率接近97%;吸附过程符合二级动力学模式,吸附等温线数据能较好的用Lamgmuir和D-R等温模式描述,吸附热力学参数△H_θ.和△G~θ为负值,说明该吸附过程为自发的放热过程.     

量热法研究线粒体代谢的热力学和动力学行为

线粒体是细胞中极为重要的细胞器，是产生细胞所必需的“富能”物质ATP的重要场所，为细胞活动提供所需化学能．在生命体能量代谢过程中除一部分能量用于合成ATP外，其余则以热的形式释出．用精密热量计测出线粒体代谢过程中的热量输出对了解线粒体的功能和代谢机制具有十分重要的意义．用微量热法研究线粒体体外代谢已有一些报导［‘，’］．本工作用精密热量计和差式扫描量热仪侧定了水稻线粒体体外代谢热谱和DSC曲线，计算了水稻线粒体活性增长速率常数，比较了不同保藏时间的水稻线粒体体外代谢的差异，并初步探讨了水稻线粒体在变…     

Fe3O4-CuO-activated carbon composite as an efficient adsorbent for bromophenol blue dye removal from aqueous solutions

Dye wastewater from industries is posing tremendous health hazards. The lethal dyes can be eliminated using nanomaterials and scientific approach like adsorption which is facile, cheap, safe as well as ecofriendly. Fe₃O₄-CuO-AC composite was prepared by a hydrothermal method and used for the removal of dyes in wastewater. The composite material was characterized by various techniques such as XRD, SEM, EDS, TEM and FT-IR. The Fe₃O₄-CuO-AC composite was used to treat five types of dyes in water. Fe₃O₄-CuO-AC composite showed the highest adsorption capability for bromophenol blue (BPB) dye. The effects of initial concentration, pH, the amount of adsorbent and temperature were also studied. The optimum conditions were found to be 20 ppm dye concentration, pH 9, an adsorbent dose of 0.06 gL^─1 at 65 °C. A removal efficiency of 97% was obtained for BPB dye during 120 min of adsorption. Kinetic studies indicated that a pseudo-second order is the most suitable model for the adsorption process. The Fe₃O₄-CuO-AC composite showed better adsorption capacity as compare to Fe₃O₄-AC except for the Methyl green dye. The maximum adsorption capacity was found to be 88.60 mg/g for BPB. Additionally, the thermodynamic parameters (ΔS°, ΔH° and ΔG°) showed that the process was spontaneous and exothermic. All the above results revealed that the Fe₃O₄-CuO-AC compositecan be an effective adsorbent for removing dyes from wastewater.     

Retention, kinetics and thermodynamics profile of cadmium adsorption from iodide medium onto polyurethane foam and its separation from zinc bulk

The sorption behaviour of 2.5 × 10⁻⁵ M solution of Cd(II) on polyurethane foam (PUF) from iodide medium have been investigated. The conditions were optimized from aqueous solutions of different pH (1-10) and of acids of varied concentration (0.01-1.0 M). The maximum concentration of KI was found to be 0.24 M and equilibration time was established to be 20 min. The data successfully followed the Freundlich and Dubinin-Radushkevich (D-R) isotherms at low metal ion concentration while Langmuir isotherm followed at higher metal ion concentration. The Freundlich parameter 1/n = 0.66 ± 0.02 have been evaluated whereas D-R isotherm yields the sorption free energy E = 10.5 ± 0.1 kJ mol⁻¹ indicating ion exchange type chemisorption. The monolayer coverage (XL) constant of Langmuir isotherm was found to be 23.7 ± 0.4 mg g⁻¹. The numerical values of thermodynamics parameters enthalpy (ΔH), entropy (ΔS) and Gibbs free energy (ΔG) indicated the endothermic and spontaneous nature of sorption. The Scatchard plot analysis was tested to evaluate the binding sites of the PUF and stability constants of sorption were determined. On the basis of these parameters, the sorption mechanism was discussed. Among the foreign ions tested, Pb(II), Hg(II), cyanide and nitrite should be absent. The clean separation of Cd(II) from Zn(II) ions in the ratio 1:250, respectively, was achieved by column chromatography.     

2-噻吩乙酸在三种不同树脂上的吸附热力学和动力学研究

通过静态吸附实验,研究了XAD-4,NDA-100和ND-90吸附树脂对水溶液中2-噻吩乙酸的吸附热力学及动力学特性,结果表明,2-噻吩乙酸在XAD-4树脂上是单层吸附,符合Langmuir等温吸附方程,吸附过程符合准一级动力学吸附方程.2-噻吩乙酸在NDA-100和ND-90树脂上的吸附也能用Langmuir等温吸附方程表示,但并不只是单层吸附,而主要是由毛细管凝聚和微孔填充作用造成的吸附,吸附过程可分为大孔和中孔区的吸附以及微孔区的吸附两个阶段,两个阶段都符合准一级动力学吸附方程.     

An outline of new calculation methods for the determination of both thermodynamic and kinetic parameters from isothermal heat conduction microcalorimetry

An outline of equations allowing calculation, from calorimetric data, of both thermodynamic and kinetic parameters for reactions which proceed to completion is given. In addition equilibrium constants are calculable for reactions which proceed to an equilibrium position. Advantages of the methods for solid state kinetic and stability studies are briefly discussed.     

Surface adsorption and micelle formation of aqueous solutions of polyethyleneglycol and sugar surfactants

The surface tension of aqueous solutions of tetraethyleneglycol octyl ether (C8E4) and octyl-β-d-maltopyranoside (OM) mixture was measured as a function of the total molality of surfactants and the composition of OM under atmospheric pressure at 298.15 K by drop volume technique. The results of surface tension measurements were analyzed by originally developed thermodynamic equations, then phase diagrams of adsorption and micelle formation were constructed. From the analysis of the surface tension data, it was found that the C8E4 and OM molecules interact attractively in the adsorbed film and the excess Gibbs energy of adsorption can be compared with those observed in typical cationic–nonionic surfactant systems; nevertheless, they are mixed almost ideally in the mixed micelle. Judging from a negative excess surface area calculated by differentiating the excess Gibbs energy by the surface tension, we concluded that the attraction between C8E4 and OM molecules is a short-range one originated in the hydrogen bonding between them which favors the planar configuration.