Dielectric,optical and structural properties of Bi4V2−xSrxO11−δ (0.05≤x≤0.20)

Composition Bi₄V_2−xSr_xO_11−δ (0.05≤x≤0.20) is synthesized by melt quench technique followed by heat treatment at 800 °C for 12 h. These compounds are characterised by X-ray diffraction, Fourier transform infrared (FTIR) spectroscopy, UV–visible spectroscopy, impedance spectroscopy and scanning electron microscopy. X-ray diffraction patterns of all the samples show γ-phase stabilization at room temperature except x=0.05 heat treated sample. The optical band gap of all the samples is observed in semiconducting range. The lowest and the highest optical band gap is 2.39 eV and 2.57 eV for x=0.10 heat treated and x=0.20 quenched samples, respectively. The highest value of dielectric constant is obtained ~10⁷ with very low dielectric loss for x=0.15 and 0.20 samples at ~350 °C and below 10 Hz. The grain size increases with dopant concentration leads to increase the dielectric constant.     

Study on electrical conductivity and phase transition in singly doped BIPBVOX (Bi2V1−xPbxO5.5−x/2) solid electrolyte

Samples of bismuth lead vanadium oxide (BIPBVOX) (Bi₂V_1–xPb_xO_5.5–x/2) singly substituted system in the composition range 0.05 ≤ x ≤ 0.20 were prepared by sol–gel synthesis route. Structural investigations were carried out by using a combination of differential thermal analysis (DTA) and powder X-ray diffraction (PXRD) technique. Energy dispersive X-ray spectroscopy analysis (EDXA) of doped samples was carried out to predict the sample purity and doping concentration. Transitions, α?β, β?γ and γ′?γ were detected by XRD, DTA and variation in the Arrhenius plots of conductivity. The ionic conductivity was measured by AC impedance spectroscopy. The solid solutions with composition x ≤ 0.07 undergo α?β phase transition, at 329 °C and β?γ phase transition at 419 °C. The highly conducting γ′-phase was effectively stabilized at room temperature for compositions with x ≥ 0.17 whose thermal stability increases with Pb content. At 300 °C, the highest value of conductivity 6.234 × 10^?5 S cm^?1 was obtained for composition x = 0.15 and at 600 °C the highest value of conductivity 0.65 S cm^?1 is observed for x = 0.17. AC impedance plots reveal that the conductivity is mainly due to the grain contribution to oxide ion conductivity.     

Synthesis,phase stability and oxide ion conductivity of Ce(IV)–Cd(II) double substituted bismuth vanadate

Bi₄V₂O_11-δ has been doped with Ce and Cd to study double substitution. The system with various dopant concentrations (0.07 ≤ x ≤ 0.30) was prepared by the standard solid-state reaction method. The correlation between the polymorphism and oxide ion performance was well investigated as a function of temperature and composition with the help of thermal analysis, X-ray diffraction (XRD) and AC impedance spectroscopy. From XRD results it is seen that the high oxide ion conducting tetragonal γ-phase is stabilized for x = 0.17. For the compositions x ≤ 0.10, monoclinic α-phase is retained at room temperature with clear evidence for two successive phase transitions α ? β and β ? γ. For x = 0.13, β ? γ phase transition is seen. However, the existence of order–disorder, γ' ? γ transition was confirmed for x = 0.17. It is seen that the highest low-temperature ionic conductivity at 320 °C is 3.19 × 10^?4 S cm^?1 which was observed for x = 0.17.     

Evidence for a valence transition in UxY1-xSb

Electrical, optical and lattice-constant measurements on single crystalline U_xY_1-xSb (x=0, 0.01, 0.03, 0.08, 0.15, 0.20, 0.30, 0.70 and 1) reveal a nonmagnetic U 5f² singlet groundstate for x ? 0.15, a lowering of the f³→f²d¹ transition energy with decreasing x for x > 0.15 and a marked anomaly of the lattice parameter for x ? 0.15. These results as well as the anomalous concentration dependence of the U moment can be described by a valence transition of U at a concentration of about 15% U (x = 0.15).     

Correlation of defect structure and ionic conductivity in δ-phase solid solutions in the Bi3NbO7–Bi3YO6 system

Defect structure and conductivity behaviour are discussed in the solid solution Bi₃Nb_1−xY_xO_7−x(0.0 ≤ x ≤ 1.0). Investigations were carried out using a combination of ac impedance spectroscopy and powder X-ray and neutron diffraction. Low temperature conductivity and activation energy both increase as a function of x. The former is attributed to an increase in oxide ion vacancy concentration, whereas the latter is due a redistribution of oxide ion vacancies as determined by neutron diffraction measurements. The defect structures at room temperature and 800 °C are presented. Curvature in Arrhenius plots of conductivity throughout the composition range is associated with a temperature dependent redistribution of oxide ions.     

Impedance and Modulus studies of the solid electrolyte system 20CdI2–80[xAg2O–y(0.7V2O5–0.3B2O3)], where 1 ≤x/y ≤ 3

In the present work, an evaluation of the transport properties of super ion conducting quaternary system 20CdI₂–80[xAg₂O–y(0.7V₂O₅–0.3B₂O₃)], where 1 ≤ x/y ≤ 3, in steps of 0.25, to study the effect of changing the modifier to former ratio on the conduction phenomena has been undertaken. Electrical conductivity measurements were made using complex impedance method. The electrical conductivity and conductivity relaxation of the system were studied in the temperature range from 303 K to 333 K and in the frequency range from 100 Hz to 10 MHz. The highest conductivity at room temperature is obtained for the system with modifier to former ratio 1.75. Impedance and modulus analyses had indicated the temperature independent distribution of relaxation times and the non-Debye behavior in these materials. The co-operative motion due to strong coupling between the mobile Ag⁺ ions is assumed to give rise to non-Debye type of relaxation. The silver ionic transport number (t_Ag+) obtained by the emf technique suggested the occurrence of silver ion conduction in the CdI₂-doped Ag₂O–V₂O₅–B₂O₃ system.     

Influence of calcium substitution on the phase transition and ionic conductivity in BICAVOX oxide ion conductor

Samples of Bi₄Ca _x V_{2? x} O_{11?(3 x /2)?δ} in the composition range 0.07 ≤ x ≤ 0.30 were prepared by conventional solid state reactions. The stability of different phases as a function of composition was analysed by X-ray powder diffraction, FT-IR spectra, differential thermal analysis and AC impedance spectroscopy. For the compositions x ≤ 0.10, monoclinic α-phase structure is retained at room temperature. For x = 0.13, orthorhombic β-phase is observed, whereas for x ≥ 0.17, high O^2?conducting tetragonal γ-phase is stabilised. However, the highest ionic conductivity σ_300°C = 3.27 × 10^?4 S cm^?1 was observed for x = 0.17. This higher value of conductivity of the substituted compound as compared to the parent compound can be attributed to the increased oxygen ion vacancies generated as a result of cation doping. AC impedance spectroscopy reveals the fact that this ionic conductivity is mainly due to the grain contribution.     

CO(III)–NI(II) double substituted bismuth vanadate: synthesis,phase stabilization,and structural and electrical characterization

Samples of Co–Ni double substituted bismuth vanadate, BICO_0.20?x NI _x VOX (Bi₄Co_0.20???x ^(III)Ni _x ^(II)V_1.8O_{10.8???(x/2)???δ} ;0?≤?x?≤?0.20) were synthesized by standard solid state reactions. The influence of Ni substitution for Co on phase stabilization and oxide-ion performance have been investigated using X-ray powder diffraction, differential thermal analysis, and AC impedance spectroscopy. The high conducting γ′-phase was effectively stabilized at room temperature for compositions with x?≥?0.13 whose thermal stability increases with Ni content. The complex plane plots of impedance were typically represented at temperatures below 380 °C, suggesting a major contribution of polycrystalline grains to the overall electrical conductivity. The dielectric permittivity measurements revealed the fact that suppression of the ferroelectric transition is compositionally dependent. Interestingly, the maximum ionic conductivity at lower temperatures (～2.56?×?10^?4 S cm^?1 at 300 °C) was observed for the composition with x?=?0.13. However, a good agreement was generally found between the values of electrical conductivity and corresponding activation energies of conduction.     

Thermoelectric performance of ternary Bi-Sb-Ag alloys prepared by mechanical alloying and subsequent pressureless sintering

The alloys with the general formula of Bi₈₅Sb_15−xAg_x (x=0, 1, 3, 5, 7) were prepared by mechanical alloying and subsequent pressureless sintering (Bi₈₅Sb₁₅ alloy was used for comparison). Their transport properties involving electrical conductivity, Seebeck coefficient, and thermal conductivity had been investigated in the temperature range of 80-300 K. The maximum absolute value of Seebeck coefficient (120 μV/K) was found at 160 K in the alloy Bi₈₅Sb_15−xAg_x (x=3). The figure-of-merit of alloy Bi₈₅Sb_15−xAg_x (x=1) reached a maximum value of 2.16×10⁻³ K⁻¹ at 219 K, which is as large again as that of the reference sample Bi₈₅Sb₁₅.     

Effect of La substitution on conductivity and dielectric properties of Bi1−xLaxFeO3 ceramics: An impedance spectroscopy analysis

Bismuth ferrite (BFO) and La-substituted BFO with composition Bi_1−xLa_xFeO₃ (x=0.05, 0.1 and 0.15) (BLFO_x=0.05-0.15) ceramics were prepared using the solid state reaction route. A structural phase transition from rhombohedral phase to triclinic phase was observed for BLFO_x=0.05-0.15 ceramics. Modulus spectroscopy reveals the deviation of dielectric behavior from ideal Debye characteristics and the dependence of conductivity on ion hopping in BFO and BLFO_x=0.05-0.15 ceramics. The conductivity of the BFO ceramics decreases for La content of 5 mol%, followed by a subsequent increase with 10 and 15 mol% of lanthanum doping. The typical values of the activation energies at high temperature reveal the contribution of short range movement of doubly ionized oxygen vacancies to the conduction process in BFO and BLFO_x=0.05 ceramics. Both short range and long range motion of oxygen vacancies are responsible for large conductivity in BLFO_{x=0.1 and 0.15} ceramics.     

Correlation between phase structure and electrical conduction in BISNVOX system for intermediate temperature solid oxide fuel cells (IT-SOFC)

Samples of Sn⁴⁺-substituted bismuth vanadate, formulated as Bi₄Sn _x V_{2? x} O_{11?( x /2)? δ} in the composition range 0.07 ≤ x ≤ 0.30, were prepared by standard solid-state reactions. Sample characterization and the principal phase transitions (α ? β, β ? γ and γ′ ? γ) were investigated by FT-IR spectroscopy, X-ray powder diffraction, differential thermal analysis (DTA) and AC impedance spectroscopy. For composition x = 0.07, the α ? β and β ? γ phase transitions were observed at temperatures of 451 and 536°C, respectively. DTA thermograms and Arrhenius plots of conductivities revealed the γ′ ? γ phase transition at 411 and 423°C for x = 0.20 and 0.30, respectively. AC impedance plots showed that conductivity is mainly due to the grain contribution, which is evident in the enhanced short-range diffusion of oxide ion vacancy in the grains with increasing temperature. The highest ionic conductivity (5.03 × 10^?5 S cm^?1 at 300°C) was observed for the x = 0.17 solid solution with less pronounced thermal hysteresis.     

Structural and electrical study of Ce-substituted bismuth vanadate

Samples of Ce^IV-substituted bismuth vanadate, formulated as Bi₄Ce_xV_2−xO_{11−(x/2)−δ}; 0≤x≤0.30, were synthesized by solid-state reactions. The phase structure and electrical conductivity were investigated using X-ray powder diffraction, FT-IR, differential thermal analysis and AC impedance spectroscopy. For a low composition range, two phase transitions, α↔β and β↔γ, were exhibited in which the system mimics in most events the parent compound. Impedance analysis evidenced no relationship between the blocking effect of charge carriers and structural changes at ambient temperatures. However, the temperature dependence of conductivity was correlated with the stability region of various phases within the system.     

Ionic conductivity and structural properties of MnO-doped Bi4V2O11 system

Bi₄V₂O₁₁ exists in three phases viz. α, β, and γ. High temperature γ-phase can be stabilized to room temperature owing to its higher conductivity by the partial substitution of metallic cations for vanadium in Bi₄V₂O₁₁. Phase transitions from α → β and β → γ are composition and temperature-dependent. Mn²⁺-doped compounds Bi₄V_2−x Mn _x O_{11− δ} (0 ≤ x ≤ 0.4) have been synthesized by solid state reaction technique and investigated by X-ray diffraction and ionic conductivity measurement. High ionic conducting γ-phase is stabilized for x ≥ 0.2. The ionic conductivity of the series of Bi₄V_2−x Mn _x O_{11− δ} samples has been measured by using ac impedance spectroscopy technique. The conductivity data do show departure from its simple Arrhenius behavior for all of the compositions. The highest conductivity observed for x = 0.2 sample can be attributed to lower activation energy.     

Composition dependence of polymorphism and electrical conductivity in Ce(IV)-doped Bi4V2O11

For the first time, a new member of the BIMEVOX family, namely BICEVOX, has been synthesized by the partial solid-state substitution of Ce(IV) for vanadium in parent Bi₄V₂O₁₁ solid electrolyte. The electrical conductivity in Bi₄Ce _x V_{2? x} O_{11?( x /2)? δ} has been investigated in the compositional range 0 ≤ x ≤ 0.30, using FT-IR, X-ray powder diffraction, differential thermal analysis and ac impedance spectroscopy. Owing to the long-term stabilization of α- and β-polymorphs compared to other members of the BIMEVOX family, the BICEVOX system may be a prospective solid electrolyte for intermediate temperature solid oxide fuel cells due to the significantly increased conductivity at lower temperatures observed for the compositions x > 0.20.     

Evolution of structural,magnetic and magnetocaloric properties in Sn-doped manganites La0.57Nd0.1Sr0.33Mn1−x Sn x O3 (x = 0.05–0.3)

Structural and magnetic properties of manganites series La_0.57Nd_0.1Sr_0.33Mn_1?x Sn _x O₃ with (0.05 ≤ x ≤ 0.30) have been investigated, and the critical exponents and magnetocaloric effect are studied around the room temperature, to shed light on Sn substitution influence. A solid-state reaction method was used in the preparation. A structural study using Rietveld refinement of XRD patterns indicates rhombohedral structure with R \( \overline{3} \) c space group for (0.05 ≤ x ≤ 0.20) and shows the existence of a secondary phase attributed to the neodymium tin oxide (Nd₂Sn₂O₇) pyrochlore for x = 0.3. The variation of the magnetization (M) vs. temperature (T), under an applied magnetic field of 0.05 T, reveals a ferromagnetic–paramagnetic transition at the Curie temperature T _C. In addition, it was discovered that increasing the tin content leads to a reduction in magnetization and a lowering of T _C from 282 K (x = 0.05) to 158 K (x = 0.20) with increasing Sn substitution. The samples exhibit the characteristics of spin/cluster-glass state which is evident from (zero-field-cooled and field-cooled) magnetization vs. temperature curves. Indeed, the thermal evolution of magnetization in the ferromagnetic phase at low temperature varies as T ^3/2, in accordance with Bloch’s law. The spin-stiffness constant D obtained from the Bloch constant was determined. A large magnetocaloric effect has been observed in both samples (x = 0.05 and x = 0.10): the maximum entropy change, \( \left| {\varDelta S_{\text{M} }^{\text{peak}} } \right| \) , reaches the highest value of 3.22 J/kg K under a magnetic field change of 5 T with a RCP value of 56 J/kg for x = 0.10 composition. This opens an interesting opportunity to this compound to compete with materials which work as magnetic refrigerants near room temperature. Besides, we show that the samples follow the conventional behavior of a second-order ferromagnetic transition. This was possible by investigating the critical behavior at the transition region by adopting the modified Arrott plot method. The values of the critical exponents (β, γ, δ and n) are determined and they are between those predicted by the three-dimensional Heisenberg model.     

Electrical transport and crystallization in Cu+ ion substituted AgI–Ag2O–V2O5 glassy superionic system

A new glassy solid electrolyte system Cu_xAg_1 − xI–Ag₂O–V₂O₅ has been synthesized. The structural, thermal and electrical properties of the samples have been investigated. The glassy nature of the samples is confirmed by X-Ray diffraction and Differential Scanning Calorimetry studies. The electrical conductivity of these samples increases with CuI content and approaches a maximum value of ∼ 10⁻² Ω^− 1 cm^− 1 for x = 0.35 at room temperature. Ionic mobility measurements suggest that enhancement in the conductivity with Cu⁺ ion substitution may be attributed to increase in the mobility of Ag⁺ ions. The electrical conductivity versus temperature cycles carried out at well-controlled heating rate above T_g and T_c reveal interesting thermal properties. For lower CuI content samples conductivity exhibits anomalous rise above T_g and subsequent fall at T_c. It is also found that CuI addition into AgI–Ag₂O–V₂O₅ matrix reduces the extent of crystallization.     

The structural and multiferroic properties of (Bi1−xLax)(Fe0.95Co0.05)O3 ceramics

La and Co co-doped BiFeO₃ ((Bi_1−xLa_x)(Fe_0.95Co_0.05)O₃ (x=0, 0.10, 0.20, 0.30)) ceramics were prepared by tartaric acid modified sol–gel method. The X-ray diffraction patterns indicate a transition from rhombohedral structure to tetragonal structure at x=0.20, which has been confirmed by the Raman measurements. The band gap increases with increasing x to 0.20, and then decreases with further increasing x to 0.30. The structural transition has significant effects on the multiferroic properties. The remnant magnetization and saturate ferromagnetic magnetization decrease abruptly with increasing x to 0.10, and then gradually increase with further increasing x up to 0.30. The coercivity is significantly reduced with increasing La doping concentration. The ferroelectricity has been improved by La doping, and the polarization increases with increasing x to 0.10, then decreases with further increasing x up to 0.30. The simultaneous coexistence of soft ferromagnetism and ferroelectricity at room temperature in tetragonal Bi_0.70La_0.30Fe_0.95Co_0.05O₃ indicates the potential multiferroic applications.     

Effect of Bi on fluorescence properties of YPO4:Dy phosphors synthesized by a modified chemical co-precipitation method

Y_0.99−xPO₄:0.01Dy³⁺, xBi³⁺ (x=0, 0.01, 0.05, 0.10, 0.15, 0.20 and 0.25) phosphors have been synthesized by a modified chemical co-precipitation method using urea as a pH value regulator. The samples were characterized by X-ray powder diffraction (XRD) and photoluminescence spectroscopy. XRD results show that the samples have only single tetragonal structure when x≤0.15, but extraneous BiPO₄ phase appears besides major tetragonal phase when x≥0.20. The crystallinity of the samples is found to improve with increasing Bi³⁺ ion concentration from 0 to 15 mol%, and then decreased for higher concentrations associated with increasing BiPO₄ phase. Photoluminescence excitation spectra results show that the phosphor can be efficiently excited by ultraviolet light from 250 to 400 nm including four peaks at 294, 326, 352 and 365 nm. Emission spectra exhibit strong blue emission (483 nm) and another strong yellow emission (574 nm). When the Bi³⁺ ion concentration is 1 mol%, the intensity of excitation and emission spectra increased evidently. In addition, the yellow-to-blue emission intensity ratio (I_Y/I_B) is strongly related to the excitation wavelength and not to the Bi³⁺ ion concentration.     

A novel red-emitting phosphor Ca9Bi(PO4)7:Eu3+ for near ultraviolet white light-emitting diodes

Red phosphors Ca₉Bi_1-x(PO₄)₇:xEu³⁺ (x = 0.06, 0.10, 0.20, 0.30, 0.40, 0.50, 0.60, 0.70, 0.80 and 1.00) were synthesized by a conventional solid-state reaction (SSR) route. The X-ray diffraction patterns, photoluminescence spectra, ultraviolet–visible reflection spectroscopy, decay time and the International Commission on Illumination (CIE) chromaticity coordinates of these compounds were characterized and analyzed. The Eu-doped Ca₉Bi(PO₄)₇ phosphors exhibited strong red luminescence which peaks located at 615 nm due to the ⁵D₀→⁷F₂ electric dipole transition of Eu³⁺ ions after excitation at 393 nm. Ultraviolet–visible spectra indicated that the band-gap of Ca₉Bi_0.30(PO₄)₇:0.70Eu³⁺ is larger than that of Ca₉Bi(PO₄)₇. The results indicate that the phosphor Ca₉Bi_0.30(PO₄)₇:0.70Eu³⁺ can be a suitable red-emitting phosphor candidate for LEDs.