2-(2-Thiazolylazo)-pcresol (TAC) as a reagent for the spectrophotometric determination of titanium (IV)

The reaction between titanium(IV) and 2-(2-thiazolylazo)-p-cresol-(TAC) in aqueous methanol media at apparent pH 4.0–5.6 results in a intensely coloured complex that is stable for at least 2 h. The combining ratio is 1 1 cation TAC. Beer's law is obeyed up to 5.0 g/ml titanium(IV) at 580 nm. The apparent molar absorptivity at 580 nm is 9.82.10³ l.mole^–1.cm^–1 and the detection limit obtained was 5 ng/ml titanium (IV). A spectrophotometric method for the simultaneous determination of titanium and iron with TAC is proposed.     

Determination of Lead Using a New Chromogenic Reagent 2-(2-Sulfo-4-acetylphenylazo)-7-(2,4,6-trichlorophenylazo)-1,8-dihydroxynaphthalene-3,6-disulfonic Acid

A novel chromogenic reagent, 2-(2-sulfo-4-acetylphenylazo)-7-(2,4,6-trichlorophenylazo)-1,8-dihydroxynaphthalene-3,6-disulfonic acid 1, was prepared by diazo coupling of 4-acetylaniline-2-sulfonic acid and 2,4,6-trichloroaniline to chromotropic acid through –N=N– groups. Based on this reagent, a simple, sensitive and selective spectrophotometric method was developed for the determination of lead. In 0.20M phosphoric acid medium, lead reacts with 1 to form a 1:2 blue complex with an absorption maximum of 654nm. Beers law is obeyed in the range of 0–0.6mgL^–1 of lead. The apparent molar absorptivity is 1.25×10⁵Lmol^–1cm^–1. The detection limit and quantification limit were found to be 0.63µgL^–1 and 2.1µgL^–1, respectively. The relative standard deviation for eleven replicate measurements was of 2.6%. The interference of foreign ions was also investigated. All the other foreign ions studied did not interfere with lead determination except for Ca(II) and Ba(II). The interference caused by Ca(II) and Ba(II) can be eliminated by prior extraction of lead with potassium iodide-methylisobutylketone (KI-MIBK). The proposed method was applied to the determination of lead in certified samples with satisfactory results.     

Extraction-spectrophotometric determination of iron(III) by means of quinaldic acid-N-oxide

Summary A simple and sensitive method for the determination of iron(III) is described. It is based on the extraction of the yellow-coloured complex of iron with quinaldic acid-N-oxide in chloroform. The absorption maximum is at 380 nm with molar absorptivity ₃₈₀=1.03 · 10⁴. Beer's Law is obeyed over the range 0.6–6 ppm iron with relative standard deviation of +-0.3% (Sandell sensitivity 0.005 g/ml/cm²). The absorbance of the reagent blank is however high with consequent occasional disturbances, which are avoided when measured at 395 nm; molar absorptivity ₃₉₅=7.4 · 10³; effective concentration range 3–8 ppm iron with relative standard deviation +-0.5% (Sandell sensitivity 0.008g/ml/cm²). A fairly large number of common ions do not interfere. Job's method of continuous variations and Asmus method indicate a iron-reagent ratio of 13. Heterogeneous formation constant is K _D =2 · 10⁸.

---

Extraktionsphotometrische Bestimmung von Eisen(III) mit Chinaldinsäure-N-oxid

Zusammenfassung Die einfache und empfindliche Bestimmung beruht auf der Extraktion des gelben Komplexes von Eisen(III) mit Chinaldinsäure-N-oxid in Chloroform. Das Absorptionsmaximum liegt bei 380 nm mit dem molaren Extinktionskoeffizient ₃₈₀=1.03 · 10⁴. Das Beersche Gesetz gilt im Bereich 0,6–6 ppm Eisen. Die relative Standardabweichung beträgt+-0,3% (Sandell-Empfindlichkeit 0,005g/ml/cm²). Die Absorption der Blindprobe ist jedoch hoch und verursacht manchmal Störungen, die beim Messen bei 395 nm vermieden werden; molarer Extinktionskoeffizient ₃₉₅= 7,4 · 10³; im Konzentrationsbereich 3–8 ppm Eisen beträgt die relative Standardabweichung+-0,5% (Sandell-Empfindlichkeit 0,008g/ml/cm²). Eine ziemlich große Zahl von Fremdionen bewirkt keine Störung. Methoden nach Job und Asmus liefern ein Verhältnis Eisen/Reagens wie 13. Die heterogene Bildungskonstante beträgt K _D =2 · 10⁸.

     

Spectrophotometric Determination of Iron(III) After Separation by Adsorption of its 2-Thenoyltrifluoroacetone Complex on Microcrystalline Naphthalene

Summary A new spectrophotometric method for the determination of iron (III) after adsorption of its red TTA complex onto microcrystalline naphthalene has been developed. Iron(III) reacts with 2-thenoyltri-fluoroacetone in pH range 2.4–5.2 to form a water-insoluble 13 red complex which is easily adsorbed onto microcrystalline naphthalene from its acetone solution. The naphthalene mixture is separated, dried and dissolved in 10 ml dioxane. The red organic phase has a plateau around 480–500 nm while the reagent has no absorbance beyond 420 nm. The system obeys Beer's law over 20–120g iron(III) in 10 ml of dioxane solution or 0.4–2.4 ppm aqueous. The molar absorptivity of the complex species is 3.9×10³·l·mol^–1·cm^–1, while the sensitivity for Fe(III) extends to 1.43×10^–2 g cm^–2 for 0.001 absorbance. Samples containing 80g of iron gave a relative standard deviation of 1.23%. The effects of experimental variables such as pH, amount of reagents, shaking and digestion time, aqueous volume and diverse ions have been examined. The method has been applied to the determination of iron(III) in standard reference and environmental samples and results compared with other standard colorimetric procedures.

---

Spektrophotometrische Bestimmung von Eisen(III) nach Adsorption seines 2-Thenoyltrifluoraceton-Komplexes an mikrokristallines Naphthalin

Zusammenfassung Eine neue spektrophotometrische Methode zur Bestimmung von Eisen (III) nach Adsorption seines roten TTA-Komplexes an mikrokristallines Naphthalin wurde ausgearbeitet. Fe(III) reagiert mit 2-Thenoyltrifluoraceton bei pH 2,4-5,2 unter Bildung eines roten, wasser-unlöslichen 13-Komplexes, der sich aus seiner acetonischen Lösung leicht an mikrokristallines Naphthalin adsorbieren läßt. Das Naphthalin-Gemisch wird abgetrennt, getrocknet und in 10 ml Dioxan gelöst. Die rote organische Phase hat ein Adsorptions-Plateau bei 480–500 nm, während das Reagens jenseits 420 nm nicht adsorbiert. Das System entspricht dem Beerschen Gesetz von 20–120g Fe(III) in 10 ml Dioxan-Lösung bzw. 0,4–2,4 ppm in wäßriger Lösung. Die molare Extinktion der Komplexverbindung beträgt 3,9× 10³l·mol^–1·cm^–1. Die Empfindlichkeit für Fe(III) entspricht 1,43×10^–2 g cm^–2 für 0,001 Absorptionseinheiten. Proben mit 80g Fe(III) zeigen eine rel. Standardabweichung von 1,23%. Die Wirkung variabler Versuchsbedingungen pH, Reagensmenge, Zeit, Volumen und diverse Fremdionen wurden geprüft. Das Verfahren wurde an Standardsubstanzen geprüft und seine Ergebnisse mit denen anderer kolorimetrischer Verfahren verglichen.

     

Spectrophotometric determination of uranium with 5-(2′-carboxyphenyl)azo-8-quinolinol in the non-ionic micellar medium of Triton X-100

Triton X-100, a non-ionic surfactant, has been used to sensitize the reaction of 5-(2-carboxyphenyl)azo-8-quinolinol with uranium in aqueous medium at pH 5.2–6.1 to form a wine red coloured complex. The micellar sensitization results in two and a half-times enhanced molar absorptivity enabling the determination of uranium in rock samples at ppm level, stability of the complex enhanced from 4 hours to at least 72 hours. Extraction of the complex is avoided making the procedure simple, rapid and easy in operation. The molar absorptivity and Sandell's sensitivity of the complex are 1.50·10⁴l·mol^–1·cm^–1 and 15.9 ng·cm^–2, respectively, at _max=568 nm. Beer's law is obeyed over the range 0–3.3 g·ml^–1 of uranium. An amount as low as 0.19 g·ml^–1 of uranium could be determined satisfactorily within a relative standard deviation of ±1.3%. The limits of determination and practical quantitation are 0.29 and 1.80 ppm, respectively. The method was applied to the determination of uranium in soil, stream sediment and rock samples.     

A Simple Sensitive Spectrophotometric Method for the Determination of Ce4+ Using Variamine Blue as a Chromogenic Reagent

A rapid and sensitive spectrophotometric method is described for the determination of trace amounts of cerium using Variamine Blue (VB) as a chromogenic reagent. The proposed method is based on the reaction of cerium with potassium iodide in acidic medium to liberate iodine, which oxidizes Variamine Blue to give a violet colored species with an absorption maximum at 560nm. Beers law was obeyed in the range 2–10µg mL^–1 of cerium. The molar absorptivity and Sandells sensitivity are found to be 1.65×10⁴L mol^–1cm^–1 and 8.48×10^–3µgcm^–2, respectively. The proposed method has been successfully applied to the determination of cerium in alloy and synthetic mixtures.     

Determination of Iron in Tap and Waste Water Using Liquid–Liquid Extraction in a Flow-Injection System

A flow-injection procedure for the determination of iron(III) in water is described. The procedure is based on the formation of an ion pair between the tetraphenylarsonium (Ph₄As⁺) (TPA) or tetrabutylammonium (But₄N⁺) (TBA) cations and the tetrathiocyanatoferrate(III) complex (TTF). This ion pair is extracted with chloroform, and the absorbance of the organic phase is measured at 503nm (for Ph₄As⁺) or 475nm (for But₄N⁺). Iron concentrations higher than 0.9×10^–6molL^–1 (50µgL^–1) can be detected in the first case, with a relative standard deviation of 1.9% (n=12), a linear application rangeof between 1.34 and 54.0×10^–6molL^–1 (75–3015µgL^–1), and a sampling frequency of 30h^–1. For the ion pair with But₄N⁺, the detection limit is 0.52×10^–6molL^–1 (29µgL^–1), with a relative standard deviation of 1.6% and a linear application range between 0.73 and 54.0×10^–6molL^–1. Under the proposed working conditions, only Pd(IV), Cu(II) and Bi(III) interfere. With the application of the merging zones technique, considerable amounts of organic reagent can be saved. The TBA method was applied to the analysis of iron(III) in tap and industrial waste waters.     

Spectrophotometric studies on the platinum(IV)-prochlorperazine bismethanesulfonate complex

We have studied the formation of a platinum complex and developed a simple, rapid and sensitive spectrophotometric method for the determination of platinum in solution. The method is based on the complexation reaction of the chromogen, prochlorperazine bismethane-sulfonate (PCPMS), with platinum(IV) in phosphoric acid medium which forms a reddish brown 1 1 complex with an absorption maximum around 528 nm. The reaction is fast in the presence of copper(II) and goes to completion within 1 min. Beer's law is obeyed over the concentration range 0.3–7.2 g/ml of platinum(IV) with an optimal range of 1.2–6.6 g/ml. The molar absorptivity is 2.65 × 10⁴1 mol^–1 cm^–1 and the Sandell's sensitivity is 7.8 ng cm^–2. The stability constant, logK, of the complex is 4.96±0.1 at 25 ° C. The effects of time, temperature, concentrations of acids, PCPMS and copper(II), and the interference by various ions are investigated. The method has been successfully applied to the determination of platinum content in alloys and minerals.     

Direct Microspectrophotometric Determination of Bismuth in Silver with Semi-Xylenol Orange

75–300ng of bismuth in a sample mass of 20mg of silver can be determined spectrophotometrically in a nitric acid medium (0.18molL^–1) with Semi-Xylenol Orange as chromogenic agent. Its selectivity is realized by using less toxic reagents in very small amounts to mask some of the interfering impurity cationic species while the matrix effect is negligible. The conditional formation constant of the colored chelate formed was found to be lgK_f=3.1. It exhibits a maximum at 540nm with a molar absorptivity of 4.2×10⁴Lmo1^–1cm^–1. The linear regression equation for this determination is A=0.022+0.0018C, where C stands for the concentration of Bi (ng per 0.5mL) with a correlation coefficient of 0.9873. The RSD at the level of 200ng of Bi (n=10) was found to be 5%.     

Spectrophotometric determination of Fe(III) with tiron in the presence of cationic surfactant and its application for the determination of iron in Al-alloys and Cu-based alloys

A sensitive Spectrophotometric method for the determination of iron with tiron and a cationic surfactant, cetylpyridinium chloride, at pH 5.6 is reported. The complex is extracted into a chloroform-propan-2-ol (41) mixture and shows maximum absorbance at 520 nm. Beer's law is obeyed in the range 1–14 g/ml with an average molar absorptivity of 15800 l mol^–1 cm^–1. The molar ratio as determined by Job's method for Fe:tiron:CPC is 143. Interferences by various ions are examined. Zr, Ti and Mo interfere heavily. The method is applied for the determination of iron in Al-based and Cu-based alloys, using appropriate masking agents.     

Spectrophotometric determination of vanadium(IV) in the presence of vanadium(V) using Br-PADAP

In the present paper, a simple and sensitive method is proposed for vanadium(IV) determination in the presence of vanadium(V). This is based on the oxidation of vanadium(IV) present in the sample to vanadium(V) by addition of iron(III) cation, followed by a complexation reaction of iron(II) with the spectrophotometric reagent 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol (Br-PADAP). The iron(II) reacts with Br-PADAP immediately, forming a stable complex with a large molar absorptivity. The vanadium(IV) determination is possible, with a calibration sensitivity of 0.549 g ml^–1, for an analytical curve of 18.8 ng ml^–1 to 2.40 g ml^–1, molar absorptivity of 2.80 × 10⁴ 1 mole^–1 cm^–1 and a detection limit of 5.5 ng ml^–1. Selectivity was increased with the use of EDTA as a masking agent. The proposed method was applied for the vanadium(IV) determination in the presence of several amounts of vanadium(V). The results revealed that 200 g of vanadium(V) do not interfere with determination of 5.00 g of vanadium(IV). The precision and the accuracy obtained were satisfactory (R. S. D.<2%).     

Thiazolylblue tetrazolium bromide — a new spectrophotometric reagent for determination of manganese

A method has been developed for the micro-determination of Mn(VII) by the selective extraction of the MnO₄ ^– anion with thiazolylblue tetrazolium bromide from acidic medium. The molar absorptivity of the complex is 1 × 10⁴lmol^–1cm^–1 at 250 nm and the system obeys Beer's law in the range 0.1–1.75 gml^–1 Mn(VII). The composition and stability of the complex are discussed. The characteristic values for the extraction equilibrium and the equilibrium in the aqueous phase are: extraction constantK _ex = 3.16 × 10⁴, distribution constantK _D = 21.85 and association constant =1.45 × 10³. Manganese(VII) was determined in soils and plants. The determination was carried out without preliminary separation of manganese.     

Pyridine ketoximes as analytical reagents: The spectrophotometric determination of iron with 2,2′-dipyridyl-α-glyoxime

Summary A spectrophotometric method for the determination of iron with 2,2-dipyridyl--glyoxime is described. The effects due to p_H, time, heating, buffers, hydroxylamine reagents concentration and diverse ions are reported. The system can tolerate large amounts of copper and nickel. Beer's law is obeyed and the molar absorptivity is 1.33 · 10⁴ l M^–1 cm^–1 at 534 nm.

---

Zusammenfassung Eine spektrophotometrische Methode der Eisenbestimmung mit 2,2Dipyridyl--glyoxim wurde beschrieben. Über den Einfluß von p_H, Zeit, Hitze, Puffern, der Hydroxylaminkonzentration im Reagens sowie diverser Fremdionen wurde berichtet. Das Verfahren ist gegenüber großen Mengen Kupfer und Nickel unempfindlich. Das Beersche Gesetz wird befolgt. Die molare Extinktion bei 534 nm beträgt 1,33 · 10⁴ l Mol^–1 cm^–1.

     

Extraction-spectrophotometric determination of trace iron (II) in sea water with 2-[2-(3,5-dibromopyridyl)azo]-5-diethylaminobenzoic acid

An extraction-spectrophotometric method is described for the determination of traces of iron(II) with 2-[2-(3,5-dibromopyridyl)azo]-5-diethyl-aminobenzoic acid. The reagent forms a stable and blue 12 iron/reagent complex that can be extracted into chloroform. The apparent molar absorptivity of the iron(II) complex is 1.09 × 10⁵ 1 mol^–1 cm^–1 at 624 nm in chloroform. The reagent is relatively selective; interferences from cobalt, copper, nickel and vanadium can be removed by using dimethylglyoxime and EDTA. The method is applied to the determination of iron (II) in sea water and aluminium alloys with good precision and accuracy.     

Extraction-spectrophotometric determination of iron with 2-(2′-benzothiazolylazo)-4,6-dimethylphenol

An extraction-spectrophotometric method for the determination of trace amounts of iron based on its extraction into chloroform with 2-(2-benzothiazolylazo)-4,6-dimethylphenol (BTADMP) from a pH 6.5 medium has been developed. The extracted 12 FeBTADMP complex species allow the determination of 4–30gmg of iron (=3.92×10⁴1·mol^–1·cm^–1 at 790 nm). The method is highly selective and has been applied to the determination of iron in polymineral-polyvitamin pharmaceutical products.     

Determination of Heavy Metal Ions in Chinese Herbal Medicine by Microwave Digestion and RP-HPLC with UV-Vis Detection

A new method for the simultaneous determination of heavy metal ions in Chinese herbal medicine by microwave digestion and reversed-phase high-performance liquid chromatography (RP-HPLC) has been developed. The Chinese herbal medicine samples were digested by microwave digestion. Lead, cadmium, mercury, nickel, copper, zinc, and tin ions in the digested samples were pre-column derivatized with tetra-(4-chlorophenyl)-porphyrin (T₄-CPP) to form the colored chelates which were then enriched by solid phase extraction with C₁₈ cartridge and eluted from the cartridge with tetrahydrofuran (THF). The chelates were separated on a Waters Xterra RP₁₈ column by gradient elution with methanol (containing 0.05molL^–1 pyrrolidine-acetic acid buffer salt, pH=10.0) and THF (containing 0.05molL^–1 pyrrolidine-acetic acid buffer salt, pH=10.0) as mobile phase at a flow rate of 0.5mLmin^–1 and detected with a photodiode array detector in the range of 350–600nm. In the original samples the detection limits of lead, cadmium, mercury, nickel, copper, zinc and tin are 4ngL^–1, 3ngL^–1, 6ngL^–1, 5ngL^–1, 2ngL^–1, 6ngL^–1, and 4ngL^–1, respectively. This method was applied to the determination of lead, cadmium, mercury, nickel, copper, zinc and tin in Chinese herbal medicine samples with good results.     

Kinetic Spectrophotometric Determination of Trace Aluminum by Catalytic Activity of Al<Superscript>3+</Superscript> on the Oxidation of Methylene Blue by Hydrogen Peroxide

A novel kinetic spectrophotometry for the determination of trace aluminum is described based on the catalytic activity of Al³⁺ on the redox reaction between methylene blue (MB) and hydrogen peroxide in acetate buffer (pH 3.8). The reaction is monitored spectrophotometrically by measuring the decrease in absorbance of the dye at the maximum absorption wavelength of 670nm. The variables that affected the reaction rate were fully investigated, and the optimum conditions were established. Aluminum can be determined in the range of 0–80ngmL^–1 with a detection limit of 1.0ngmL^–1. The relative standard deviation for 10 replicate determinations of 40ngmL^–1 aluminum is 0.9%. The method was used to determine aluminum in tap water and biological samples and produced satisfactory results.Received December 18, 2002; accepted May 5, 2003 published online August 22, 2003     

Extraction-spectrophotometric determination of nickel as Ni-(PAR)2-(CTAB)2 complex in polymetallic sea-bed nodules and steels

A red, water-soluble complex of nickel with PAR can be extracted into chloroform with CTAB at pH 7.0. The system obeys Beer's law upto 0.5 g/ml with a molar absorptivity of 45 200 L·mol^–1·cm^–1 at 540 nm. Job's method of continuous variations revealed that the composition of the extracting species is 1:2:2 for nickel:PAR:CTAB. Based on this extraction, a highly sensitive and selective spectrophotometric method for the determination of nickel in polymetallic sea-bed nodules and in steels, after prior separation of iron and manganese, was developed. The standard deviation was 0.04–0.127 g for 5–25 g of nickel.     

Solid-Phase Extraction and Spectrophotometric Determination of Trace Amounts of Mercury in Natural Samples

A sensitive and selective solid phase spectrophotometric method for the determination of trace amounts of inorganic mercury is described. Hg²⁺ was sorbed on a silica gel-packed column as an Hg²⁺–N,N-bis(2-mercaptophenyl)ethanediamide (H₂L) complex. The Hg²⁺ complex was eluted from the column using 7mL of acetone. Various parameters including pH, column flow rate, and ligand concentration were optimized. The complex was found to obey Beers law from 2.3 to 73.7µgmL^–1 within the optimum range when the preconcentration factor was two. The effective molar absorption coefficient at 523nm was 1.17×10³Lmol^–1cm^–1 at 523nm. The concentration limits in Beers law dropped from 0.09 to 2.95µgmL^–1 within the optimum range when the preconcentration factor was 50. The relative standard deviation at a concentration level of 5µgmL^–1 Hg²⁺ (9 repetitive determinations) was 1.6%. The detection limits are 0.34µgmL^–1 and 0.015µgmL^–1 when the preconcentration factors are 2 and 50, respectively. The method has been used for routine determination of trace levels of Hg²⁺ in natural waters. The potential application of this method for the removal of Hg²⁺ from natural samples (sea water and lake water) spiked with 100ngmL^–1 of Hg²⁺ was studied. In order to validate the proposed method, LGC 6156 (harbour sediment – extractable metals) was analysed by this method. The results proved that excellent extraction of Hg²⁺ from both natural water samples was obtained by solid phase extraction using N,N-bis(2-mercaptophenyl) ethanediamide.     

Spectrophotometric and atomic absorption determination of Ni(II) in fresh and sea waters after preconcentration by flotation

A highly selective and sensitive procedure for flotation separation followed by spectrophotometric determination, confirmed by AAS, of Ni(II) traces is proposed. The maximum flotation separation (100%) is achieved at 25° C in the pH range of 1–3 using sodium diethyldithiocarbamate (as a collector) and oleic acid surfactant. The floated (1 : 2) colored complex is measured spectrophotometrically at 430 nm over a concentration range of 0.5–4.0 g/g with a molar absorptivity of 0.44 × 10⁴ L mol^–1 cm^–1. The procedure was successfully applied for the separation and determination of Ni(II) in fresh and sea waters.