等浓度的氯化铵和硫酸铵溶液哪个pH高

有中学化学参考资料题:0.10 mol/L的NH4Cl和(NH4)2SO4溶液哪个pH值高?这似乎是个中学生可做的简单题目,仔细考虑不是如此.如果简单地认为盐酸和硫酸都是强酸,而硫酸是二元酸,硫酸铵溶液中铵盐浓度为0.20 mol/L,那么NH4Cl溶液pH高,那是不妥的.硫酸是二元酸,第一个氢离子能完全电离,第二个氢离子部分电离,如此考虑情况怎么样呢?是不是答案发生变化?这要通过计算来说明.     

Enhanced efficiency and stability in Sn-based perovskite solar cells with secondary crystallization growth

The conversion efficiencies reported for Tin(Sn)halide-based perovskite solar cells(PSCs)fall a large gap behind those of lead halide-based PSCs,mainly because of poor film quality of the former.Here we report an efficient strategy based on a simple secondary crystallization growth(SCG)technique to improve film quality for tin halide-based PSCs by applying a series of functional amine chlorides on the perovskite surface.They were discovered to enhance the film crystallinity and suppress the oxidation of Sn²⁺remarkably,hence reduce trap state density and non-irradiative recombination in the absorber films.Furthermore,the SCG film holds the band levels matching better with carrier transport layers and herein favoring charge extraction at the device interfaces.Consequently,a champion device efficiency of 8.07% was achieved alo ng with significant enhancements in VOC and JSC,in contrast to 5.35% of the control device value.Moreover,the SCG film-based devices also exhibit superior stability comparing with the control one.This work explicitly paves a novel and general strategy for developing high performance lead-free PSCs.     

Energy level engineering of charge selective contact and halide perovskite by modulating band offset:Mechanistic insights

Mixed cation and anion based perovskites solar cells exhibited enhanced stability under outdoor conditions,however,it yielded limited power conversion efficiency when TiO₂ and Spiro-OMeTAD were employed as electron and hole transport layer(ETL/HTL)respectively.The inevitable interfacial recombination of charge carriers at ETL/perovskite and perovskite/HTL interface diminished the efficiency in planar(n-i-p)perovskite solar cells.By employing computational approach for uni-dimensional device simulator,the effect of band offset on charge recombination at both interfaces was investigated.We noted that it acquired cliff structure when the conduction band minimum of the ETL was lower than that of the perovskite,and thus maximized interfacial recombination.However,if the conduction band minimum of ETL is higher than perovskite,a spike structure is formed,which improve the performance of solar cell.An optimum value of conduction band offset allows to reach performance of 25.21%,with an open circuit voltage(VOC)of 1231 mV,a current density JSC of 24.57 mA/cm² and a fill factor of 83.28%.Additionally,we found that beyond the optimum offset value,large spike structure could decrease the performance.With an optimized energy level of Spiro-OMeTAD and the thickness of mixed-perovskite layer performance of 26.56% can be attained.Our results demonstrate a detailed understanding about the energy level tuning between the charge selective layers and perovskite and how the improvement in PV performance can be achieved by adjusting the energy level offset.     

A new strategy to access Co/N co-doped carbon nanotubes as oxygen reduction reaction catalysts

Carbon nanotubes(CNTs),as one-dimensional nanomaterials,show great potential in energy conversion and storage due to their efficient electrical conductivity and mass transfer.However,the security risks,time-consuming and high cost of the preparation process hinder its further application.Here,we develop that a negative pressure rather than a following gas environment can promote the generation of cobalt and nitrogen co-doped CNTs(Co/N-CNTs) by using cobalt zeolitic imidazolate framework(ZIF-67) as a precursor,in which the negative pressure plays a key role in adjusting the size of cobalt nanoparticles and stimulating the rearragement of carbon atoms for forming CNTs.Importantly,the obtained Co/N-CNTs,with high content of pyridinic nitrogen and abundant graphitized structure,exhibit superior catalytic activity for oxygen reduction reaction(ORR) with half-wave potential(E_1/2) of 0.85 V and durability in terms of the minimum current loss(2%) after the 30,000 s test.Our development provides a new pathway for large-scale and cost-effective preparation of metal-doped CNTs for various applications.     

Recent Advances of Pure Organic Room Temperature Phosphorescence Materials for Bioimaging Applications

Bioimaging,as a powerful and helpful tool,which allows people to investigate deeply within living organisms,has contributed a lot for both clinical theranostics and scientific research.Pure organic room temperature phosphorescence(RTP)materials with the unique features of ultralong luminescence lifetime and large Stokes shift,can efficiently avoid biological autofluorescence and scattered light through a time-resolved imaging modality,and thus are attracting increasing attention.This review classifies pure organic RTP materials into three categories,including small molecule RTP materials,polymer RTP materials and supramolecular RTP materials,and summarizes the recent advances of pure organic RTP materials for bioimaging applications.     

Stabilizing High-voltage Cathode Materials for Next-generation Li-ion Batteries

The pressing demand for high-energy/power lithium-ion batteries requires the deployment of cathode materials with higher capacity and output voltage.Despite more than ten years of research,high-voltage cathode mate-rials,such as high-voltage layered oxides,spinel LiNi0.5Mn1.5O4,and high-voltage polyanionic compounds still cannot be commercially viable due to the instabilities of standard electrolytes,cathode materials,and cathode electrolyte interphases under high-voltage operation.This paper summarizes the recent advances in addressing the surface and interface issues haunting the application of high-voltage cathode materials.The understanding of the limitations and advantages of different modification protocols will direct the future endeavours on advancing high-energy/power lithium-ion batteries.     

Conformational Properties of Comb-shaped Polyelectrolytes with Negatively Charged Backbone and Neutral Side Chains Studied by a Generic Coarse-grained Bead-and-Spring Model

A generic coarse-grained bead-and-spring model,mapped onto comb-shaped polycarboxylate-based(PCE)superplasticizers,is developed and studied by Langevin molecular dynamics simulations with implicit solvent and explicit counterions.The agreement on the radius of gyration of the PCEs with experiments shows that our model can be useful in studying the equilibrium sizes of PCEs in solution.The effects of ionic strength,side-chain number,and side-chain length on the conformational behavior of PCEs in solution are explored.Single-chain equilibrium properties,including the radius of gyration,end-to-end distance and persistenee length of the polymer backbone,shape-asphericity parameter,and the mean span dimension,are determined.It is found that with the increase of ionic strength,the equilibrium sizes of the polymers decrease only slightly,and a linear dependenew of the persistence length of backbone on the Debye screening length is found,in good agreement with the theory developed by Dobrynin.Increasing side-chain numbers and/or side-chain lengths increases not only the equilibrium sizes(radius of gyration and mean span)of the polymer as a whole,but also the persistence length of the backbone due to excluded volume interactions.     

Suppressing trap states and energy loss by optimizing vertical phase distribution through ternary strategy in organic solar cells

Suppressing the trap-state density and the energy loss via ternary strategy was demonstrated.Favorable vertical phase distribution with donors(acceptors)accumulated(depleted)at the interface of active layer and charge extraction layer can be obtained by introducing appropriate amount of polymer acceptor N2200 into the systems of PBDB-T:IT-M and PBDB-TF:Y6.In addition,N2200 is gradiently distributed in the vertical direction in the ternary blend film.Various measurements were carried out to study the effects of N2200 on the binary systems.It was found that the optimized morphology especially in vertical direction can significantly decrease the trap state density of the binary blend films,which is beneficial for the charge transport and collection.All these features enable an obvious decrease in charge recombination in both PBDB-T:IT-M and PBDB-TF:Y6 based organic solar cells(OSCs),and power conversion efficiencies(PCEs)of 12.5%and 16.42%were obtained for the ternary OSCs,respectively.This work indicates that it is an effective method to suppress the trap state density and thus improve the device performance through ternary strategy.     

Three-dimensionalization via control of laser-structuring parameters for high energy and high power lithium-ion battery under various operating conditions

Laser-structuring is an effective method to promote ion diffusion and improve the performance of lithium-ion battery(LIB)electrodes.In this work,the effects of laser structuring parameters(groove pitch and depth)on the fundamental characteristics of LIB electrode,such as interfacial area,internal resistances,material loss and electrochemical performance,are investigated,LiNi_0.5Co_0.2Mn_0.3O₂ cathodes were structured by a femtosecond laser by varying groove depth and pitch,which resulted in a material loss of 5%-14%and an increase of 140%-260%in the in terfacial area between electrode surface and electrolyte.It is shown that the importance of groove depth and pitch on the electrochemical performance(specific capacity and areal discharge capacity)of laser-structured electrode varies with current rates.Groove pitch is more im porta nt at low current rate but groove depth is at high curre nt rate.From the mapping of lithium concentration within the electrodes of varying groove depth and pitch by laser-induced breakdown spectroscopy,it is verified that the groove functions as a diffusion path for lithium ions.The ionic,electronic,and charge transfer resistances measured with symmetric and half cells showed that these internal resistances are differently affected by laser structuring parameters and the changes in porosity,ionic diffusion and electronic pathways.It is demonstrated that the laser structuring parameters for maximum electrode performance and minimum capacity loss should be determined in consideration of the main operating conditions of LIBs.     

Mesh-like vertical structures enable both high areal capacity and excellent rate capability

In order to balance electrochemical kinetics with loading level for achieving efficient energy storage with high areal capacity and good rate capability simultaneously for wearable electronics,herein,2 D meshlike vertical structures(NiCo_2 S_4@Ni(OH)_2) with a high mass loading of 2.17 mg cm^-2 and combined merits of both 1 D nanowires and 2 D nanosheets are designed for fabricating flexible hybrid supercapacitors.Particularly,the seamlessly interconnected NiCo_2 S_4 core not only provides high capacity of 287.5 μAh cm^-2 but also functions as conductive skeleton for fast electron transport;Ni(OH)_2 sheath occupying the voids in NiCo_2 S_4 meshes contributes extra capacity of 248.4 μAh cm^-2;the holey features guarantee rapid ion diffusion along and across NiCO_2 S_4@Ni(OH)_2 meshes.The resultant flexible electrode exhibits a high areal capacity of 535.9 μAh cm^-2(246.9 mAh g^-1) at 3 mA cm^-2 and outstanding rate performance with 84.7% retention at 30 mA cm^-2,suggesting efficient utilization of both NiCo_2 S_4 and Ni(OH)_2 with specific capacities approaching to their theoretical values.The flexible solid-state hybrid device based on NiCo_2 S_4@Ni(OH)_2 cathode and Fe_2 O_3 anode delivers a high energy density of 315 μWh cm^-2 at the power density of 2.14 mW cm^-2 with excellent electrochemical cycling stability.     

Ultrasound-assisted one-pot synthesis of 2,4,5-triarylimidazole derivatives catalyzed by ceric (Ⅳ) ammonium nitrate in aqueous media

2,4,5-Triarylimidazoles could be obtained in excellent yields by the one-pot three-component condensation of benzil/benzoin, aldehydes and ammonium acetate in the presence of catalytic amount of the inexpensive,readily available and non-toxic ceric(Ⅳ) ammonium nitrate(CAN) in aqueous media under ultrasound at room temperature.In this reaction the products were obtained in short reaction time and easy operation under mild conditions.     

Silica nanoparticles obtained by microwave assisted sol–gel process: multivariate analysis of the size and conversion dependence

Silica nanoparticles were synthesized by the sol–gel method in alcoholic solution under microwave irradiation in the presence of an ammonium catalyst. The effect of the reaction time, the reaction temperature, water and ammonium concentrations on particle size and conversion (measured by light scattering and FTIR respectively) were analyzed using multivariate analysis. The results showed that water and ammonium concentrations are the main factors that control the particle size and the conversion. Both properties increase with water and ammonium concentration. Moreover, comparing with the results obtained using traditional heating, the microwave heating gave rise to higher reaction rate and narrower dispersion of the particle size.     

Convenient,Mild and One‐Pot Synthesis of Double Schiff Bases from Three Component Reaction of Salicylaldehyde,Ammonium Acetate and Aliphatic Aldehydes Accelerated by NEt3 as a Base

A convenient and efficient procedure for one‐pot preparation of double Schiff bases through a three component reaction of salicylaldehyde, ammonium acetate and aliphatic aldehyde was described. In this reaction, N,N′‐bis(salicylidene)‐1,1‐diaminoalkanes was easily obtained in excellent yields and short reaction times under mild reaction condition.     

Acceleration of ammonium nitrite denitrification by freezing: determination of activation energy from the temperature of maximum reaction rate

A reaction of ammonium nitrite in ice was investigated. Upon freezing, some nitrite is oxidized by dissolved oxygen and some nitrite reacts with ammonium to produce nitrogen and water in a denitrification reaction. The former reaction was accelerated only during freezing, and the latter one was accelerated even after the whole sample was frozen. The denitrification reaction proceeded at very low concentration in ice, which were conditions under which the reaction would not proceed in solution. The nitrogen production increased linearly with increasing initial concentration of ammonium nitrite. The concentration factor in the unfrozen solution in ice was estimated to be 50.6 when the initial concentration was 0.5 mmol dm(-3), as obtained from comparison of reaction rates in solution and in ice. A new method for determination of the activation energy is proposed that gives a value of 53 to 61 kJ mol(-1) for denitrification. The reaction order of the denitrification process is also determined using our method, and it is concluded to follow third-order kinetics.     

高效可重复使用多相催化剂Ce(SO_4)_2·4H_2O用于无溶剂一锅合成2,3-二氢喹唑啉-4(1H)-酮(英文)

Cerium(IV) sulfate tetrahydrate, Ce(SO4)2·4H2O, is a novel inorganic solid acidic catalyst that efficiently catalyzes the synthesis of 2,3-dihydroquinazolin-4(1H)-ones via the one-pot three- component reaction of isatoic anhydride, aromatic aldehydes, and a nitrogen source(ammonium acetate, ammonium carbonate, ammonium chloride, or methylamine) under solvent-free conditions. The desired products are obtained in short reaction time with high yields. The catalyst is inexpensive and readily available and can be recovered conveniently and reused such that considerable catalytic activity can still be achieved after the fifth run. Easy work-up and avoiding the use of harmful organic solvents are other advantages of this simple procedure.     

KI与无机铵盐催化CO2与环氧丙烷合成碳酸丙烯酯

以无毒、合成简单、廉价的无机铵盐(氨基甲酸铵、碳酸氢铵、碳酸铵等)为助催化剂,研究其对卤化钾(KCl、KBr、KI)催化CO2与环氧丙烷合成碳酸丙烯酯(PC)的影响.结果表明,卤化钾与无机铵盐显示出很好的协同催化效应.其中以氨基甲酸铵为助催化剂,KI为主催化剂时,催化合成PC的效果最好.同时考察了催化剂用量、反应温度、CO2初始压力、PC的预加入量、反应时间等因素对反应的影响.在优化条件下,PC收率大于99%.     

PTC‐Promoted Japp–Klingmann Reaction for the Synthesis of Indole Derivatives

Abstract

Indole derivatives have been efficiently synthesized from ethyl 2‐phenylhydrazono‐5‐phthalimido‐pentanoate and its derivatives, which were obtained by Japp–Klingmann reaction under phase‐transfer catalytic (PTC) conditions. Several different phase‐transfer catalysts were investigated and dimethyldioctadecyl ammonium chloride (DMDOA) was found to promote this reaction efficiently. Using DMDOA as the PTC, aryl hydrazones were obtained in yields of 90%. The pure aryl hydrazones were then efficiently cyclized to indole derivatives in yields of more than 80%.     

Synthesis and characterization of chitosan grafted poly(N,N-dimethyl-N-methacryloxyethyl-N-(3-sulfopropyl) ammonium) initiated by ceric (IV) ion

Grafting of N,N-dimethyl-N-methacryloxyethyl-N-(3-sulfopropyl) ammonium (DMMSA) onto chitosan using ceric ammonium nitrate as an initiator was studied under nitrogen atmosphere in 2% wt. acetic acid solution. The grafted polymer was confirmed by FT-IR spectroscopy. The extent of grafting could be adjusted by controlling the appropriate reaction conditions. The maximum percentage of grafting about 50% was obtained under optimum condition. A representative grafted copolymer was characterized by thermogravimetric analysis and chitosan was used as reference.     

KI与无机铵盐催化CO2与环氧丙烷合成碳酸丙烯酯

以无毒、合成简单、廉价的无机铵盐(氨基甲酸铵、碳酸氢铵、碳酸铵等)为助催化剂, 研究其对卤化钾(KCl、KBr、KI)催化CO₂与环氧丙烷合成碳酸丙烯酯(PC)的影响. 结果表明, 卤化钾与无机铵盐显示出很好的协同催化效应. 其中以氨基甲酸铵为助催化剂, KI为主催化剂时, 催化合成PC的效果最好. 同时考察了催化剂用量、反应温度、CO₂初始压力、PC的预加入量、反应时间等因素对反应的影响. 在优化条件下, PC收率大于99%.     

Asymmetric synthesis of beta-hydroxy amino acids via aldol reactions catalyzed by chiral ammonium salts

The Cinchona alkaloid derived chiral ammonium salt developed by Park and Jew functions as an effective catalyst for the synthesis of beta-hydroxy alpha-amino acids via asymmetric aldol reactions under homogeneous conditions. The syn diastereomers are obtained in good ee, and aryl-substituted aliphatic aldehydes are the best substrates for the reaction. These results represent the highest ee's obtained to date in direct aldol reactions of glycine equivalents catalyzed by inexpensive, readily prepared chiral ammonium salts.