对苯二甲酸镁作为钠离子电池的有机负极材料

报道了对苯二甲酸镁作为钠离子电池负极材料的研究.以对苯二甲酸和氢氧化镁为原料,采用酸碱中和反应制备了含结晶水的对苯二甲酸镁(MgC8H4O4·2H2O),该材料对钠离子电池表现出了较好的电化学活性、优异的倍率性能以及良好的循环稳定性.在0.5C(1C=300 mA·g-1)倍率下循环50周以后,可逆容量由114mAh·g-1降至95 mAh·g-1,容量保持率高达83%;在2C的倍率下有高达90 mAh·g-1的可逆比容量.另外,在氮气气氛中,400℃进行后续热处理得到了不含结晶水的对苯二甲酸镁(MgC8H4O4),探讨了结晶水对其电化学性能的影响.结果表明,MgC8H4O4·2H2O的比容量、倍率性能以及循环稳定性都明显优于不含结晶水的对苯二甲酸镁.     

钠离子电池负极材料

钠离子电池具有钠资源丰富和成本低廉等特点,吸引了国内外研究者的广泛关注,被认为是今后在规模储能领域可能替代锂离子电池的最佳候选。近几年钠离子电池的研究相继取得了重要进展,研究体系不断丰富。本文对钠离子电池负极材料的研究现状进行了详细的综述,重点介绍了碳基材料、合金材料、非金属单质、金属氧化物以及有机化合物等嵌钠性能及可能的嵌钠机理。探讨了这些材料目前所面临的主要问题及可能的解决策略,并对钠离子电池今后的研究方向和应用前景进行了展望。     

钠离子电池炭基负极材料研究进展

钠离子电池是目前新兴的低成本储能技术,因在大规模电化学储能中具有较好的应用前景而受到了国内外学者广泛的关注与研究。作为钠离子电池的关键电极材料之一,非石墨的炭质材料因具有储钠活性高、成本低廉、无毒无害等诸多优点,而被认为是钠离子电池实际应用时负极的最佳选择。本文详细综述了目前钠离子电池炭基负极材料的研究进展,重点介绍了炭质材料的储钠机理与特性,分析了炭材料结构与电化学性能之间的关系,探讨了其存在的问题,为钠离子电池炭基负极材料的发展提供有益的认识。     

钠离子储能电池关键材料

钠离子电池是一种新型电化学电源,具有原材料资源丰富、成本较低、比容量和效率较高等优点,较为符合规模化储能应用要求,在提升大规模可再生能源并网接入能力、提高电能使用效率和电能质量方面具有应用潜力。在这一背景下,钠离子电池近年来引起全世界范围内的广泛关注,关键材料和相关技术研究进展迅速。本文从钠离子电池的负极材料和正极材料两方面对近年来的主要研究工作进行综述,同时简略介绍了与之匹配的电解质体系的研究进展,讨论了当前面临的主要技术关键点和难点,并尝试对我国科研和产业工作者在该领域的研究工作提出一些建议。     

室温钠离子储能电池电极材料结构研究进展

随着风能和太阳能等新能源的大规模发展及未来智能电网的实现,大规模储能系统显得越来越重要.室温钠离子电池以较低的成本再次引起了研究者的兴趣,并成为一种有前途、低成本的储能体系.目前,已提出多种材料可作为钠离子电池的电极材料.一般而言,材料的性质主要由材料的晶体结构决定,本文主要介绍目前提出的多种可行室温钠离子电池电极材料的晶体结构,希望通过总结已有电极材料的晶体结构,对新材料的设计提供指导.     

钠离子电池用碳负极材料研究进展

相较于目前主流的锂离子电池,钠离子电池成本相对较低,因而有望在未来大规模储能系统中获得重要应用,然而其实用化进程仍受制于缺少合适的正负极材料,特别是性能优异且实用化的负极材料.钠离子电池与锂离子电池具有相似的工作原理,但钠离子和锂离子在碳负极材料中的储存行为却有着很大的不同.总体而言,碳材料仍是目前最有望促进钠离子电池实用化的关键负极材料.本文系统总结并分析了目前已有碳材料中钠离子的储存机制,对负极材料的设计思路和研究进展进行了概述,着重阐述了商用化碳分子筛在钠离子电池中的实用化前景.最后,本文对钠离子电池中碳负极材料的未来发展方向进行了展望.     

硬碳作为钠离子电池负极材料的研究进展

硬碳由于具有来源广泛、制备简单、稳定性好等优势而成为钠离子电池负极材料的理想选择之一。从硬碳的来源、合成方法、孔结构和杂原子掺杂等4个方面对硬碳负极材料在近5年的发展进行了概述。     

碳包覆纳米SnSb合金作为高性能钠离子电池负极材料

采用喷雾热解法合成了碳包覆的SnSb/C合金复合材料,利用X射线粉末衍射仪(XRD)、场发射扫描电子显微镜(FESEM)、透射电子显微镜(TEM)等方法对产物的物相和形貌进行了表征,其中SnSb/C颗粒为10 nm左右的复合材料(10-SnSb/C)作为钠离子电池负极时,表现出优异的循环和倍率性能。首圈放电达到722.1m Ah·g~(-1),首圈库仑效率86.3%,在100、1000、3000 m A·g~(-1)下比容量分别为607.7、645.4、452.2 m Ah·g~(-1),在1000 m A·g~(-1)电流下循环200周后可逆容量达到623 m Ah·g~(-1),容量保持率为95%。SnSb/C复合材料出色的储钠性能源于其完全被碳包裹的纳米结构,该结构可以有效提高活性物质的利用率,促进电子、离子的传导,并且抑制纳米粒子在长循环过程中的粉化和团聚。     

二维层状氮化二钙作为钠离子电池负极材料

以Ca₃N₂为前驱体,用高温热解法制备了2D层状结构Ca₂N 并用X射线和扫描电镜对Ca₂N的组成、结构和形貌进行了表征。 作为钠离子电池新型负极材料,在50 mA/g电流密度充放电,首次放电比容量可达584 mA·h/g,可逆比容量达180 mA·h/g。在2000 mA/g大电流密度下,仍有70 mA·h/g。     

锂离子电池TiO2纳米管负极材料

锂离子电池负极材料二氧化钛(TiO₂)由于其零应变、环境友好和高安全性近年来得到了广泛的研究,但其较低的电子电导和离子迁移率以及较低的比容量(335 mAh·g^-1)限制了其应用前景.本文梳理了一种纳米结构TiO₂纳米管(TNTs)的研究历程以及最近研究进展,综述了TNTs常见的几种制备方法,即水热法、阳极氧化法和模板法及其形成机理,归纳了各种制备方法的优缺点,讨论了制备过程中各项参量对制得TNTs的影响.阐述了其晶体结构与形貌对电化学性能的影响,指出晶格取向一致、管壁厚度小,纳米管开口且同向排列的TNTs具有更好的电化学性能.同时探讨了针对该材料电导性差、比容量低而进行的包括结构设计、掺杂、复合等一系列改进措施,指出与高电导率及高比容量材料复合是一种方便有效的改进措施.最后总结了各种改性方法取得的进展及存在的不足,展望了TNTs的研究趋势和发展前景.     

钠离子电池用高性能锑基负极材料的调控策略研究进展

锑(Sb)具有高的理论比容量、较小的电极极化、合适的Na⁺脱嵌电位、价格低廉以及环境友好的优势,而成为一种具有较大应用前景的钠离子电池负极材料。但是,Sb基负极材料的一个重要挑战是在循环过程中高比容量伴随着大的体积变化,进而导致活性材料粉化,并从集流体上脱落,这大大限制了其在钠离子电池领域的大规模应用。因此,如何解决Sb基负极材料充放电过程中体积膨胀问题对于高性能的钠离子电池设计是至关重要的。本文详细综述和讨论了Sb基材料的结构-性能关系及其在钠离子电池中的应用,详细介绍了钠离子电池Sb基负极材料在氧化还原反应机理、形貌设计、结构-性能关系等方面的最新研究进展。本综述的主要目的是探讨影响Sb基负极材料性能的决定因素,从而提出有前途的改性策略,以提高其可逆容量和循环稳定性。最后,对Sb基钠离子电池负极材料的未来发展、面临的挑战和前景进行了展望。本文可为Sb负极材料的构建和优化提供具体的观点,阐明了Sb基负极材料未来的发展方向,从而促进钠离子电池的快速发展和实际应用。     

Sodium Ion Batteries using Ionic Liquids as Electrolytes

Sodium ion batteries have been developed using ionic liquids as electrolytes. Sodium is superior to lithium as a raw material for mass production of large‐scale batteries for energy storage due to its abundance and even distribution across the earth. Ionic liquids are non‐volatile and non‐flammable, which improved the safety of the batteries remarkably. In addition, operation temperatures were extended to higher values, improving the performance of the batteries by facilitating the reaction at the electrode and mass transfer. Binary systems of sodium and quaternary ammonium salts, such as 1‐ethyl‐3‐methylimidazolium and N‐methyl‐N‐propylpyrrolidinium bis(fluorosulfonyl)amide, were employed as electrolytes for sodium ion batteries. A series of positive and negative electrode materials were examined to be combined with these ionic liquid electrolytes. A 27 Ah full cell was fabricated employing sodium chromite (NaCrO₂) and hard carbon as positive and negative electrode materials, respectively. The gravimetric energy density obtained for the battery was 75 Wh kg^?1 and its volumetric energy density was 125 Wh L^?1. The capacity retention after 500 cycles was 87 %. Further improvement of the cell performance and energy density is expected on development of suitable electrode materials and optimization of the cell design.     

钠离子电池用高性能锑基负极材料的调控策略研究进展

Na-ion batteries (SIBs) are promising alternatives for Li-ion batteries owing to the natural abundance of sodium resources and similar energy storage mechanisms. Although significant progress has been achieved in research on SIBs, there remain several challenges to be addressed. One of the major challenges in the construction of high-performance SIBs is the development of suitable anode materials with a large reversible capacity, high cycling stability, and good rate performance. Alloying anode materials mainly composed of elements from Groups IVA and VA, as well as their alloys, have attracted widespread attention because of their low working voltage, high cost-effectiveness, and large theoretical capacity. Alloying-type anode materials can be alloyed with metallic Na to achieve large reversible capacities, ensuring a high energy density. Antimony is a promising anode material for SIBs owing to its high theoretical specific capacity (660 mAh·g⁻¹, corresponding to the full sodiation Na₃Sb alloy), small degree of electrode polarization (~0.25 V), appropriate Na⁺ deintercalation potential (0.5–0.75 V), low price, and environmental friendliness. However, an important challenge for using Sb-based anode materials is that the high specific capacity is accompanied by large volume changes during cycling. Such changes lead to the pulverization of the active materials and their falling off from the collector, which significantly limit their large-scale application in the field of sodium-ion batteries. Therefore, mitigating the volume expansion issue of Sb-based anode materials in the charge-discharge process is very important for the design of high-performance SIBs. In recent years, researchers have attempted to address this issue by designing special structures to prepare various composites, and substantial progress has been achieved in improving the electrochemical performance of SIBs. In this review, the relationship between the structure and properties of Sb-based materials and their applications in SIBs are presented and discussed in detail. The latest research progress on using Sb-based anode materials for SIBs in redox reaction mechanisms along with their morphology design, structure-performance relationship, etc. have been reviewed. The main objective of this review is to explore the determining factors of the performance of Sb-based anode materials to propose suitable modification strategies for improving their reversible capacity and cycle stability. Finally, future developments, challenges, and prospects of Sb-based anode materials for SIBs are discussed. Despite several challenges, Sb-based materials are very promising anode materials for SIBs with alloying reaction mechanisms. To further improve the large-scale application of Sb-based anode materials, it is necessary to optimize the binder, electrode structure, and electrolyte composition. The combination of in-depth studies on the electrochemical reaction mechanisms and advanced characterization technologies is important for the development and construction of advanced Sb-based anode materials for SIBs. Finally, to achieve extensive large-scale applications, it is necessary to further explore environmentally friendly, low-cost, and controllable synthetic technologies to prepare high-performance Sb-based anode materials. This review provides specific perspectives for the construction and optimization of Sb-based anode materials and suggests scope for future work on Sb-based anode materials, thereby promoting the rapid development and practical application of SIBs.      

二硫化钦作为锉离子电池负极材料的特性

采用固相法合成了纯六方相的TiS₂粉体. X射线衍射(XRD)、扫描电子显微镜(SEM)结果表明该材料具有特征层状结构, 其颗粒大小在10-20 μm之间. 作为锂离子电池负极材料, TiS₂在3.00 V(vs. Li⁺/Li)以下有3个明显的放电平台, 首次可逆容量达668 mAh·g^-1, 在第一个放电电压范围(3.00-1.40 V)内具有优异的循环可逆性. 深度放电时由于Li₂S的生成和材料颗粒严重破碎, 在低于0.50 V时材料的循环性能不佳. 通过减小材料颗粒度和提高导电剂含量, TiS₂的电化学性能得到显著改善.     

锂离子电池锡镍合金负极材料的掺杂改性

采用化学还原共沉积法,对Sn-Ni合金分别进行Sb、Cu和Co掺杂改性;研究了掺杂对Sn-Ni合金电化学性能的影响.结果表明:掺杂后的合金材料综合电化学性能都有所提高,其中Co改性Sn-Ni合金的性能最佳.20次循环后,Sn-Ni-Co合金的放电容量仍高达365 mAh.g-1,比Sn-Ni合金的高49%;而Sn-Ni-Sb和Sn-Ni-Cu合金在相同条件下的放电容量仅分别提高37%和24%.     

纳米MnO锂离子电池负极材料的制备与性能

以高锰酸钾和抗坏血酸合成的MnC₂O₄·2H₂O为前驱体, 通过固相烧结制备了纳米MnO材料. 分别采用X射线衍射(XRD)、扫描电子显微镜(SEM)和恒电流充放电技术考察了其晶相结构、颗粒形貌和电化学性能.分析结果表明, 该纳米MnO具有面心立方的岩盐结构, 结晶度良好. 其颗粒是由粒径为50-100 nm的一次颗粒结合而成的二次颗粒, 大小约为400-600 nm. 当充放电电流密度为46.3 mA·g^-1时, 纳米MnO的首次库仑效率可达68.9%, 可逆比容量为679.7 mAh·g^-1. 在141.1 mA·g^-1的电流密度下循环50圈后, 比容量由584.5mAh·g^-1降至581.5 mAh·g^-1, 容量保持率高达99.5%, 表现出优异的循环性能. 此外, 当电流密度增加到494.7 mA·g^-1 (~2C)时, 其比容量依然可达290 mAh·g^-1, 表现出较好的倍率性能和快速充放电能力. 因此, 纳米MnO具有比容量高、循环稳定、倍率性能好和安全环保等优点,是一种非常有前景的锂离子电池负极材料.