银纳米颗粒负载阶层多孔二氧化硅块体的制备及表征

以溶胶-凝胶伴随相分离法制备的阶层多孔二氧化硅作为载体,3-氨丙基三乙氧基硅烷(APTES)为改性剂,乙醇为还原剂,在阶层多孔二氧化硅固体骨架上进行银纳米颗粒均匀负载.利用扫描电镜(SEM)、透射电镜(TEM)、X射线衍射(XRD)、汞压、N2吸附/脱附、X射线光电子能谱(XPS)等测试技术对银纳米颗粒负载阶层多孔二氧化硅进行了表征,探讨了APTES表面改性、乙醇还原机理以及银纳米颗粒负载块体的孔结构特征变化规律.结果表明:APTES表面改性将氨基接枝于阶层骨架上,氨基与银离子形成银氨离子,银氨离子经乙醇还原后将平均粒径约16 nm的银纳米颗粒成功负载于二氧化硅的大孔及介孔内部;负载后的阶层多孔块体的大孔骨架未受到破坏,但其比表面积由418 m2·g-1下降到254m2·g-1,两次还原负载能提高银纳米颗粒的负载量.     

氮掺杂介孔碳的制备及其电化学超电容性能

通过直接炭化沸石咪唑酯骨架结构材料（ZIF-8）纳米多面体,成功制备了氮掺杂介孔碳（NMCs）. 采用扫描电子显微镜（SEM）、透射电子显微镜（TEM）、X射线衍射（XRD）、拉曼光谱、X射线光电子能谱（XPS）及比表面和孔隙度分析仪对其微观形貌和结构进行了表征,并对NMCs的电化学超电容性能进行了测试. 结果表明：NMCs具有规整的形貌、介孔纳米结构和较大比表面积（2737 m²·g^-1）;由于氮元素掺杂所赋予的优异的表面润湿性和赝电容性能,且介孔结构有利于电解质到达电极活性材料表面,NMCs表现出优异的电化学超电容性能,在1 A·g^-1的电流密度下,1.0 mol·L^-1H₂SO₄溶液中的比电容值为307 F·g^-1,并具有良好的功率特性;此外,在10A·g^-1的大电流密度下充放电循环5000次后,NMCs的比电容值保持率为96.9%.     

阶层多孔二氧化硅块体材料的制备与表征

以正硅酸甲酯(TMOS)为前驱体、0.01 mol·L^-1盐酸为催化剂、聚环氧乙烷(PEO, 分子量为10 000)为相分离剂、环氧丙烷(PO)为凝胶促进剂、十二烷基硫酸钠(SDS)为造孔剂, 采用溶胶-凝胶伴随相分离制备阶层多孔二氧化硅块体材料, 利用差热分析(DTA)、热重分析(TG)、傅里叶变换红外(FT-IR)光谱、扫描电镜(SEM)、X射线衍射(XRD)、N2吸附/脱附装置等测试技术对所制得的阶层多孔块体进行了表征, 探究造孔剂SDS对大孔和介孔结构的影响机理。研究表明:SDS在凝胶过程中以胶束的形式进入到骨架中形成介孔孔道;当SDS为0.21 g时, 块体材料的阶层多孔结构最优, 大孔孔径为1~3 μm, 介孔孔径为4~5 nm, 比表面积为650 m²·g^-1;800 ℃热处理后, 大孔结构和骨架上的介孔基本保持, 比表面积仍能达到421 m²·g^-1, 体现出良好的热稳定性。     

溶胶-凝胶伴随相分离制备SiO2多孔块体

以正硅酸甲酯(TMOS)为前驱体, 0.01 mol·L^-1盐酸(HCl)为催化剂, 环氧丙烷(PO)为凝胶促进剂, 粘均分子量(M_v)为10000的聚氧化乙烯(PEO)为相分离诱导剂, 采用溶胶-凝胶伴随相分离制备SiO₂多孔块体材料,利用差热分析(DTA)、傅里叶变换红外(FT-IR)光谱、扫描电镜(SEM)、X射线衍射(XRD)、汞压、N₂吸附/脱附等测试技术对所制得的SiO₂多孔块体进行了表征, 探讨了环氧化物调控溶胶-凝胶以及PEO诱导相分离机理. 结果表明, 加入PEO能诱导SiO₂凝胶发生相分离, 当PEO/TMOS摩尔比为0.0018时, 可以获得共连续多孔结构的SiO₂块体材料, 其大孔孔径分布在1-3 μm之间, 比表面积达719 m²·g^-1, 孔体积为0.48 m³·g^-1. 环氧丙烷因其环氧原子的强亲核性和不可逆的开环反应, 促进溶胶-凝胶转换, 同时借助吸附在SiO₂低聚物上的PEO诱导SiO₂凝胶相分离, 从而制备共连续大孔及骨架结构的多孔块体.     

互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体,水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂）,制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM）,透射电镜（TEM）,X射线衍射（XRD）,热重分析（TGA）对其结构进行表征;采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面,形成多层次结构,并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构;MnO₂纳米片具有典型的K-Birnessite 型晶体结构;复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1;随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极,活性炭（AC）为负极,1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器,发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V,容量可达86F·g^-1,且表现出良好的电容特性和大电流放电性能.     

互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体，水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂），制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM），透射电镜（TEM），X射线衍射（XRD），热重分析（TGA）对其结构进行表征；采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面，形成多层次结构，并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构；MnO₂纳米片具有典型的K-Birnessite 型晶体结构；复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1；随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极，活性炭（AC）为负极，1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器，发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V，容量可达86F·g^-1，且表现出良好的电容特性和大电流放电性能.     

互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体，水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂），制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM），透射电镜（TEM），X射线衍射（XRD），热重分析（TGA）对其结构进行表征；采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面，形成多层次结构，并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构；MnO₂纳米片具有典型的K-Birnessite 型晶体结构；复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1；随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极，活性炭（AC）为负极，1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器，发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V，容量可达86F·g^-1，且表现出良好的电容特性和大电流放电性能.     

互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体,水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂）,制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM）,透射电镜（TEM）,X射线衍射（XRD）,热重分析（TGA）对其结构进行表征;采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面,形成多层次结构,并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构;MnO₂纳米片具有典型的K-Birnessite 型晶体结构;复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1;随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极,活性炭（AC）为负极,1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器,发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V,容量可达86F·g^-1,且表现出良好的电容特性和大电流放电性能.     

互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体，水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂），制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM），透射电镜（TEM），X射线衍射（XRD），热重分析（TGA）对其结构进行表征；采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面，形成多层次结构，并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构；MnO₂纳米片具有典型的K-Birnessite 型晶体结构；复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1；随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极，活性炭（AC）为负极，1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器，发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V，容量可达86F·g^-1，且表现出良好的电容特性和大电流放电性能.     

互通多孔碳/二氧化锰纳米复合材料的原位水热合成及电化学性能

以互通多孔碳（IPC）为载体，水热条件下在碳表面原位反应生成纳米结构的二氧化锰（MnO₂），制备互通多孔碳/二氧化锰纳米（IPC/MnO₂）复合电极材料. 采用扫描电镜（SEM），透射电镜（TEM），X射线衍射（XRD），热重分析（TGA）对其结构进行表征；采用循环伏安法、恒流充放电和交流阻抗对其电化学性能进行研究. 结果表明：生成的MnO₂均匀地负载在碳的表面，形成多层次结构，并且随着温度的升高IPC表面负载的MnO₂由纳米颗粒变为纳米片状结构；MnO₂纳米片具有典型的K-Birnessite 型晶体结构；复合物中MnO₂的含量约为34%（w）. 在100 ℃制备的IPC/MnO₂复合材料在三电极系统中最高比电容达到了411 F·g^-1；随着反应温度的升高,比容量先增长后基本保持不变. 以IPC/MnO₂为正极，活性炭（AC）为负极，1 mol·L^-1 Na₂SO₄溶液为电解液组装成IPC/MnO₂//AC 混合超级电容器，发现IPC/MnO₂电极的电容器其电位窗口从1 V扩展到1.8 V，容量可达86F·g^-1，且表现出良好的电容特性和大电流放电性能.     

One‐pot synthesis of a new high vinyl content hybrid silica monolith dedicated to nanoliquid chromatography

A new vinyltrimethoxysilane‐based hybrid silica monolith was developed and used as a reversed‐phase capillary column. The synthesis of this rich vinyl hybrid macroporous monolith, by cocondensation of vinyltrimethoxysilane with tetramethoxysilane, was investigated using an unconventional (formamide, nitric acid) porogen/catalyst system. A macroporous hybrid silica monolith with 80% in mass of vinyltrimethoxysilane in the feeding silane solution was obtained and compared to a more conventional low vinyl content hybrid monolith with only of 20% vinyltrimethoxysilane. Monoliths were characterized by scanning electron microscopy, ²⁹Si nuclear magnetic resonance spectroscopy and N₂ adsorption–desorption. About 80% of the vinyl precursor was incorporated in the final materials, leading to 15.9 and 61.5% of Si atoms bonded to vinyl groups for 20% vinyltrimethoxysilane and 80% vinyltrimethoxysilane, respectively. The 80% vinyltrimethoxysilane monolith presents a lower surface area than 20% vinyltrimethoxysilane (159 versus 551 m²/g), which is nevertheless compensated by a higher vinyl surface density. Chromatographic properties were evaluated in reversed‐phase mode. Plots of ln(k) versus percentage of organic modifier were used to assess the reversed‐phase mechanism. Its high content of organic groups leads to high retention properties. Column efficiencies of 170 000 plates/m were measured for this 80% vinyltrimethoxysilane hybrid silica monolith. Long capillary monolithic columns (90 cm) were successfully synthesized (N = 120 000).     

Preparation and evaluation of a macroporous molecularly imprinted hybrid silica monolithic column for recognition of proteins by high performance liquid chromatography

A novel type of macroporous molecularly imprinted hybrid silica monolithic column was first developed for recognition of proteins. The macroporous silica-based monolithic skeleton was synthesized in a 4.6 mm i.d. stainless steel column by a mild sol–gel process with methyltrimethoxysilane (MTMS) as a sole precursor, and then vinyl groups were introduced onto the surface of the silica skeleton by chemical modification of γ-methacryloxypropyltrimethoxysilane (γ-MAPS). Subsequently, the molecularly imprinted polymer (MIP) coating was copolymerized and anchored onto the surface of the silica monolith. Bovine serum albumin (BSA) and lysozyme (Lyz), which differ greatly in molecular size, isoelectric point, and charge, were representatively selected for imprinted templates to evaluate recognition property of the hybrid silica-based MIP monolith. Some important factors, such as template–monomer molar ratio, total monomer concentration and crosslinking density, were systematically investigated. Under the optimum conditions, the obtained hybrid silica-based MIP monolith showed higher binding affinity for template than its corresponding non-imprinted (NIP) monolith. The imprinted factor (IF) for BSA and Lyz reached 9.07 and 6.52, respectively. Moreover, the hybrid silica-based MIP monolith displayed favorable binding characteristics for template over competitive protein. Compared with the imprinted silica beads for stationary phase and in situ organic polymer-based hydrogel MIP monolith, the hybrid silica MIP monolith exhibited higher recognition, stability and lifetime.     

Hierarchically porous Fe_2O_3 /CuO composite monoliths:Synthesis and characterization

In this paper,hierarchically porous Fe2O3 /CuO composite monoliths were first successfully synthesized by a mild method using silica monoliths as templates.The structure of composite monoliths was characterized by X-ray diffraction,scanning electron microscopy,nitrogen adsorption-desorption.The results indicated that the molar ratio of Fe to Cu had a great influence on the crystal phase of Fe2O3,pore size and the structure of the macroporous wall.The Fe2O3 /CuO composite monoliths consist of hierarchically macroporous and mesoporous structure,while the sample with the Fe/Cu molar ratio of 2:1 possesses tighter wall structure than other samples.It is expected that asprepared Fe2O3/CuO composite monoliths have potential applications in several fields as catalysts,catalyst supports,chemical sensors and high-performance liquid chromatography (HPLC).     

Fabrication of large‐sized silica monolith exceeding 1000 mL with high structural homogeneity

Reproducible fabrication of the hierarchically porous monolithic silica in a large volume exceeding 1000 mL has been established. By the hydrothermal enlargement of the fully accessible small pores to exceed 50 nm in diameter, the capillary force emerged on solvent evaporation was dramatically reduced, which allowed the preparation of crack‐free monoliths with evaporative solvent removal under an ambient pressure. The local temperature inhomogeneity within a reaction vessel in a large volume was precisely controlled to cancel the heat evolved by the hydrolysis reaction of tetramethoxysilane and that consumed to melt ice cubes dispersed in the solution, resulting in large monolithic silica pieces with improved structural homogeneity. Homogeneity of the pore structure was confirmed, both on macro‐ and mesoscales, using SEM, mercury intrusion, and nitrogen adsorption/desorption measurements. Furthermore, the deviations in chromatographic performance were examined by evaluating multiple smaller monolithic columns prepared from the monolithic silica pieces cut from different parts of a large monolith. All the daughter columns thus prepared exhibited comparable performances to each other to prove the overall homogeneity of the mother monolith. Preliminary results on high‐speed separation of peptides and proteins by the octadecylsilylated silica monolith of the above production have also been demonstrated.     

Mutual consistency between simulated and measured pressure drops in silica monoliths based on geometrical parameters obtained by three-dimensional laser scanning confocal microscope observations

The geometrical properties of co-continuous macroporous silica monoliths have been studied by laser scanning confocal microscopy (LSCM) and a comparison has been made with those obtained by conventional mercury intrusion method. Tetrahedral skeleton model (TMS), which mimics the gel skeleton shape of monoliths, was compared with real monoliths in terms of macropore and porosity using the geometrical parameters extracted from the LSCM observations. Liquid flow behavior through the macroporous silica monoliths was examined in comparison with those simulated using TSM, based on the geometrical properties obtained from LSCM observations. Heterogeneity in macropore topology and connectivity in pores and skeletons are suggested to contribute to the improvement of the model structure for macroporous monoliths.     

High-performance computing of flow and transport in physically reconstructed silica monoliths

This work presents an approach towards resolving hydrodynamic flow in real porous media by carrying out direct numerical simulations in the reconstructed macroporous (flow-through) domain of a silica monolith. The macroporous domain of a 60 μm × 60 μm × 12 μm segment of a 100 μm i.d. capillary silica monolith was reconstructed by confocal laser scanning microscopy. A 60 μm × 12 μm × 12 μm segment of the reconstructed domain was then used as the 3D matrix for simulation of fluid flow by the lattice-Boltzmann method on a high-performance computing platform. Excellent agreement is observed between the experimental and simulated Darcy permeabilities without any assumptions or further adjustments on the monolith morphology. The flow velocity field is analyzed in detail, including longitudinal and transverse velocity distributions, the occurrence of negative longitudinal velocities, as well as the beginning transition to the viscous-inertial flow regime. The presented methodology promises great potential for resolving the key relationships between morphology and band broadening in monolithic columns for HPLC applications.     

Preparation,characterisation and modification of carbon‐based monolithic rods for chromatographic applications

A range of porous carbon‐based monolithic (PCM) rods with flow‐through pore sizes of 1, 2, 5 and 10 μm, were produced using a silica particle template method. The rods were characterised using SEM and energy‐dispersive X‐ray spectroscopy, BET surface area and porous structure analysis, dilatometry and thermal gravimetry. SEM evaluation of the carbon monolithic structures revealed an interconnected rigid bimodal porous structure and energy‐dispersive X‐ray spectroscopy analysis verified the quantitative removal of the embedded silica beads. The specific surface areas of the 1, 2, 5 and 10 μm rods were 178, 154, 84 and 125 m²/g after pyrolysis and silica removal, respectively. Shrinkage of the monolithic rods during pyrolysis is proportional to the particle size of the silica used and ranged from 9 to 12%. Mercury porosimetry showed a narrow distribution of pore sizes, with an average of ～700 nm for the 1 μm carbon monolith. The suitability of bare and surface oxidised PCM rods for the use as a stationary phase for reversed and normal phase LC was explored. The additional modification of PCM rods with gold micro‐particles followed by 6‐mercaptohexanoic acid was performed and ion‐exchange properties were evaluated.     

Internally dispersed synthesis of uniform silver nanoparticles via in situ reduction of [Ag(NH3)2]+ along natural microfibrillar substructures of cotton fiber

Silver nanoparticles (Ag NPs) are known to have efficient antimicrobial properties, but the direct application of Ag NPs onto the surface of textiles has shown to be ineffective and raise environmental concerns because Ag NPs leach out during washing. In this study, non-leaching and stable Ag-cotton nanocomposite fiber was produced by the in situ formation of Ag NPs inside the cotton fiber. The reported method is to introduce a nanofluidic system in alkali-swollen cotton fiber. Sequential flows of [Ag(NH₃)₂]⁺ and reductant aqueous fluids into the opened microfibrillar channels yielded a self-assembly of Ag ions on the deprotonated cellulose and subsequent nucleation and particle growth on the microfibrils. Transmission electron and field emission scanning electron microscopy images showed Ag NPs evenly dispersed throughout the entire cross-section of the fiber and their fixation onto the isolated secondary cell wall, respectively. Despite the rapid reduction reaction and the absence of a stabilizing agent, the successful formation of monodispersed Ag NPs (12 ± 3 nm) was attributed to the self-controlled function of the highly organized microfibrillar substructures, which regulated the transport and mixing of reactants. Incorporation of Ag NPs into the internal structure of the cotton fiber did not significantly influence the cotton crystalline structure.     

γ-Ray induced catalytic properties of the silica nanoparticles dispersed in the aerated aqueous solution

Silica nanoparticles (NPs) dispersed in an aerated aqueous solution containing Ag⁺ were irradiated to a dose of 10 kGy using ⁶⁰Co γ-rays. The typical surface plasmon band of Ag NPs was observed around 400 nm, indicating that even in the presence of dissolved oxygen the reduction of Ag⁺ occurred by silica NPs. Transmission electron microscopy images indicated that Ag NPs formed on the surface of the silica NPs. The subtraction spectra showed broad absorption around 500 nm with the absorbance depending on the dose. The electrons generated by charge separation from silica NPs with a size of about 12 nm reduce Ag⁺ to Ag⁰ and form (Ag⁰) _n species on the silica NPs, and the type of (Ag⁰) _n species formed depended on the silica NP, and Ag⁺ contents, and the dose. In the co-presence of organic molecules on the silica NP such as rhodamine, the absorbance of the surface plasmon band of both Ag NPs and rhodamine decreased, indicating the electrons to participate in the reductive decomposition of rhodamine molecules adsorbed on the silica NP. Furthermore, in the case when the silica NPs contained fluorescein molecules, the fluorescein molecules were also decomposed, indicating that the fluorescein molecules adsorbed on the inner surface of the silica NPs. The addition of I₂ as an oxidative reagent prevented the decomposition of the fluorescein molecules, indicating that electrons are the main species emitted from irradiated silica NPs.