Simultaneous determination of 11 drugs belonging to four different groups in human urine samples by reversed-phase high-performance liquid chromatography method

A new, accurate, sensitive and fast reversed-phase high-performance liquid chromatography (RP-HPLC) as an analytical method for the quantitative determination of 11 drugs in human urine was worked out, optimized and validated. The objects of analysis were imipenem (IMP), paracetamol (PAR), dipyrone (DPR), vancomycin (VCM), amikacin (AMK), fluconazole (FZ), cefazolin (CFZ), prednisolone (PRE), dexamethasone (DEX), furosemide (FUR) and ketoprofen (KET) belonging to four different groups (antibiotics, analgesic, demulcent and diuretic). For HPLC analysis, diode array (DAD) and fluorescence (FL) detectors were used. The separation of analyzed compounds was conducted by means of a LiChroCART^® Purospher^® C₁₈e (125 mm × 3 mm, particle size 5 μm) analytical column with LiChroCART^® LiChrospher^® C₁₈ (4 mm × 4 mm, particle size 5 μm) pre-column with gradient elution. Analyzed drugs were determined within 20 min. The mobile phase was comprised of various proportions of methanol, acetonitrile and 0.05% trifluoroacetic acid in water. AMK was separated and determined from human urine using ortho-phthaldialdehyde-3-mercaptopropionic acid (OPA-3-MPA) as a fluorescent reagent by RP-HPLC-FL. The following retention times for drugs IMP, PAR, DPR, VCM, AMK, FZ, CFZ, PRE, DEX, FUR and KET in human urine were found: 4.01 min, 4.86 min, 6.71 min, 8.14 min, 9.46 min, 10.01 min, 10.90 min, 13.34 min, 14.06 min, 16.03 min and 18.98 min, respectively. Excellent linearity was obtained for compounds in the range of concentration: 0.35-42 μg ml⁻¹, 0.5-45 μg ml⁻¹, 4.5-38 μg ml⁻¹, 0.25-25 μg ml⁻¹, 0.5-35 μg ml⁻¹, 0.25-22 μg ml⁻¹, 0.03-52 μg ml⁻¹, 0.15-25 μg ml⁻¹, 0.25-28 μg ml⁻¹, 0.05-18 μg ml⁻¹ and 0.15-35 μg ml⁻¹ for IMP, PAR, DPR, VCM, AMK, FZ, CFZ, PRE, DEX, FUR and KET, respectively. The limits of detection (LOD) and limits of quantification (LOQ) for analyzed drugs were calculated in all cases and recovery studies were also performed. Ten human urine samples obtained from patients treated in hospital have been tested. In analyzed samples, one or more drugs from the 11 examined drugs were detected. The concentrations of examined drugs in urine samples ranged between: 1.5-12 μg ml⁻¹ of PAR, 5.2-11.5 μg ml⁻¹ of DPR, 0.13-9.5 μg ml⁻¹ of CFZ and 0.1-8 μg ml⁻¹ of FUR. This method can be successfully applied to routine determination of all these drugs in human urine samples.     

Synchronous fluorescence determination of protein with functionalized CdS nanoparticles as a fluorescence probe

Nanometer-sized fluorescent particles have been successfully synthesized. A synchronous fluorescence method, with high sensitivity and selectivity, has been developed for rapid determination of protein with functionalized CdS as a fluorescence probe. When Δλ=260 nm, maximum synchronous fluorescence is produced at 274 nm at pH 7.0. Under optimal conditions, the calibration graphs are linear over the range 0.1-3.0 μg ml⁻¹ for bovine serum albumin (BSA), 0.1-11.0 μg ml⁻¹ for γ-globulin (γ-G) and 0.1-1.4 μg ml⁻¹ for human serum albumin (HSA), respectively. Limits of determination were 0.01 μg ml⁻¹ for BSA, 0.019 μg ml⁻¹ for γ-G and 0.021 μg ml⁻¹ for HSA, respectively. The relative standard deviations of seven replicate measurements were 1.8% for 1.0 μg ml⁻¹ BSA, 2.2% for 1.0 μg ml⁻¹ γ-G and 2.3% for 1.0 μg ml⁻¹ HSA.     

Simultaneous spectrophotometric determination of iron, nickel and cobalt in micellar media by using direct orthogonal signal correction-partial least squares method

A very simple and selective spectrophotometric method for simultaneous determination of iron(II), nickel(II) and cobalt(II) based on formation of their complexes with 1-(2-pyridylazo)-2-naphtol (PAN) in micellar media is described. Although the complexes of Fe(II), Ni(II) and Co(II) with reagent show a spectral overlap, they have been simultaneously determined by partial least squares (PLS) with and without preprocessing step using direct orthogonal signal correction (DOSC). The linear range was 0.30-4.50 μg ml⁻¹ for Co(II), 0.20-3.00 μg ml⁻¹ for Ni(II) and 0.30-5.00 μg ml⁻¹ for Fe(II). The results obtained by the PLS and DOSC-PLS were statistically compared. Interference effects of common anions and cations were studied and the proposed method was also applied satisfactorily to the determination of Fe(II), Ni(II) and Co(II) in synthetic samples.     

Using on-line solid phase extraction for flow-injection spectrophotometric determination of salbutamol

In the proposed procedure, the determination of salbutamol with Folin-Ciocalteau reagent (FC) using a flow injection analysis technique (FIA) with spectrophotometric detection at 750 nm is described. The lab-made FIA system consisted of a peristaltic pump Gilson Minipulse 3 equipped with Tygon tubes, double 6-port external Vici Valco sample injector and S 2000/SAD500 fiber optic spectrophotometer. It was controlled by a PC with use of originally compiled LabVIEW^®—supported software containing the mathematical library with various statistical functions for off-line data evaluation. Concentration, volume of reagents and flow rate were optimised by a simplex method. The proposed system was used for the direct determination of salbutamol sulphate in the tablets and the human urine without preliminary pre-treatment of the sample. The negative effect of interfering substances (excipients of the tablets and matrix of the urine) is overcome by a solid phase extraction (SPE), when salbutamol is adsorbed on the solid phase in the microcolumn, which is integrated directly into the flow system. Pre-treatment of the sample takes place directly in the flowing stream. The sample throughput without carryover of on-line SPE was 60-80 samples per hour. With the SPE column (Baker—carboxylic acid), salbutamol was determined in the linear range from 1 to 15 μg ml⁻¹ (R.S.D.=1.2%), with detection limit (3σ) 0.1 μg ml⁻¹ and a frequency of 40-60 samples per hour in the water solutions. The salbutamol was determined in the linear range from 2 to 20 μg ml⁻¹ (R.S.D.=1.7%), with detection limit (3σ) 1 μg ml⁻¹ and a frequency of 30 samples per hour in the samples of the human urine.     

Chemiluminescence determination of citrate and pyruvate and their mixtures by the stopped-flow mixing technique

A novel kinetic chemiluminescent method using the stopped-flow mixing technique has been investigated for the rapid and sensitive determination of citrate and pyruvate. The method is based on a tris(2,2′-bipyridiyl)ruthenium(III) (Ru(bpy)₃³⁺) chemiluminescence (CL) reaction. Ru(bpy)₃³⁺ was generated in the mixing chamber by oxidising tris(2,2′-bipyridyl)ruthenium(II) with cerium(IV). After selecting the best operating parameters, calibration graphs were obtained over the concentration ranges 0.38-38 μg ml⁻¹ and 8.7-1300 ng ml⁻¹ for citrate and pyruvate, respectively. The limits of detection were 0.1 μg ml⁻¹ for citrate and 0.3 ng ml⁻¹ for pyruvate. Based on the differential rate of the chemiluminescent reaction corresponding to citrate and pyruvate, a very simple kinetic procedure was developed for the simultaneous determination of both compounds. Mixtures of citrate and pyruvate in ratios between 15:1 and 1.5:1 were satisfactorily resolved. The proposed method was successfully applied to the determination of citrate in pharmaceutical formulations, pyruvate in animal blood serum and both compounds in human urine.     

Simultaneous fluorimetric determination of glyphosate and its metabolite, aminomethylphosphonic acid, in water, previous derivatization with NBD-Cl and by partial least squares calibration (PLS)

The reactions of 4-chloro-7-nitrobenzofurazan (NBD-Cl) with glyphosate (GLY) and with its main metabolite, aminomethylphosphonic acid (AMPA), have been studied. The resolution of binary mixtures of glyphosate and aminomethylphosphonic acid has been accomplished by partial least squares (PLS) multivariate calibration. The method of determination is based on the fluorescence emission of the derivatives formed in presence of NBD-Cl at 90 °C, in methanol and in basic medium. The dynamic ranges of the methods were comprised between 10 and 150 μg l⁻¹ for GLY and between 10 and 200 μg l⁻¹ for AMPA, being the detection limits 2 and 5.4 μg l⁻¹ for GLY and AMPA, respectively. The total luminiscence information of the derivatives has been used to optimize the spectral data set to perform the calibration, by analysis of the three-dimensional excitation-emission matrices. A comparison between the predictive ability of the multivariate calibration method, partial least squares type 1 (PLS-1), on two spectral data sets, emission and synchronous spectra, has been performed. The PLS-1 method, applied to the emission spectra, has been selected as optimum. The proposed method has been applied to the simultaneous determination of GLY and AMPA in river water. For concentrations ranging from 100 to 600 μg l⁻¹ of each compound in the samples, analytical recoveries range from 83 to 94% for GLY and from 104 to 120% for AMPA.     

Ultra-trace level determination of hydroquinone in waste photographic solutions by UV-vis spectrophotometry

A simpler UV-vis spectrophotometric method was investigated for hydroquinone (HQ) determination using KMnO₄ as oxidizing agent for conversion of HQ to p-benzoquinone (BQ) as well as signal enhancer. Various parameters such as analytical wavelength, stability time, temperature, pH, solvent effect and interference of chemicals were checked and parameters optimized by using 1 μg ml⁻¹ standard solution of HQ. Beer's Law was applicable in the range of 0.07-2 μg ml⁻¹ and 0.005-0.05 μg ml⁻¹ at 245.5 nm and at 262 nm for aqueous standard solutions of HQ with linear regression coefficient value of 0.9978 and 0.9843 and detection limit of 0.021 μg ml⁻¹ and 0.0016 μg ml⁻¹ HQ, respectively. Standard deviation of 1.7% and 2.4% was true for 1 μg ml⁻¹ and 0.03 μg ml⁻¹ HQ solution (n = 11) run at respective wavelengths. The method was successfully applied to dilute waste photographic developer samples for free HQ determination.     

Flow injection spectrophotometric determination of andrographolide from Andrographis paniculata

A simple flow injection colourimetric procedure for determining andrographolide was proposed. It is based on the reaction between andrographolide with 3,5-dinitrobenzoic acid, resulting in an intense purplish red complex with a suitable absorption at 536 nm. A standard or sample solution was injected into the 3,5-dinitrobenzoic acid stream (flow rate of 1.0 ml min⁻¹) which was then merged with potassium hydroxide stream with the same flow rate. Optimum conditions for determining andrographolide were investigated by univariate method. Under the optimum conditions, a linear calibration graph was obtained over the range 5.0-150.0 μg ml⁻¹ and the detection limit was 1.50 μg ml⁻¹ (3σ). The relatives standard deviation of the proposed method calculated from 10 replicate injections of 10.0 and 80.0 μg ml⁻¹ andrographolide were 0.66% and 1.64%, respectively. The sample throughput was 50 h⁻¹. The proposed method has been satisfactorily applied to the determination of andrographolide in herb plant samples.     

Development of an optical chemical sensor based on 2-(5-bromo-2-pyridylazo)-5-(diethylamino)phenol in Nafion for determination of nickel ion

An optical chemical sensor based on immobilization of 2-(5-bromo-2-pyridylazo)-5-(diethylamino)phenol (Br-PADAP) in Nafion membrane is described. The membranes were cast onto glass substrates and were used for the determination of nickel in aqueous solutions by spectrophotometry. The sensor system is highly transparent, mechanically stable and showed no evidence of reagent leaching. The influence of several parameters such as pH, ligand concentration, and type and concentration of regenerating solution were optimized. The sensor system showed good sensitivity in the range 0.5-20 μg ml⁻¹ with a detection limit of 0.3 μg ml⁻¹ Ni(II). The sensor has been incorporated into a home-made flow-through cell for determination of nickel in flowing streams with improved sensitivity, precision and detection limit. The calibration curve in the flow system was linear in the range 0.1-16 μg ml⁻¹ with a detection limit of 0.07 μg ml⁻¹. The sensor is easily regenerated by dilute nitric acid solution. The proposed method was successfully applied to the determination of nickel content in vegetable oil and chocolate samples and the results were compared with those obtained using atomic absorption spectrometry.     

Simultaneous determination of albumin and immunoglobulin G with fluorescence spectroscopy and multivariate calibration

A method is proposed for the simultaneous determination of albumin and immunoglobulin G (IgG1) with fluorescence spectroscopy and multivariate calibration with partial least squares regression (PLS). The influence of some instrumental parameters were investigated with two experimental designs comprising 19 and 11 experiments, respectively. The investigated parameters were excitation and emission slit, detection voltage and scan rate. When a suitable instrumental setting had been found, a minor calibration and test set were analysed and evaluated. Thereafter, a larger calibration of albumin and IgG1 was made out of 26 samples (0-42 μg ml⁻¹ albumin and 0-12.7 μg ml⁻¹ IgG1). This calibration was validated with a test set consisting of 14 samples in the same concentration range. The precision of the method was estimated by analysing two test set samples for six times each. The scan modes tested were emission scan and synchronous scan Δ60 nm. The results showed that the method could be used for determination of albumin and IgG1 (albumin, root mean square error of prediction (RMSEP) <2, relative standard error of prediction (RSEP) <6% and IgG1, RMSEP <1, RSEP <8%) in spite of the overlapping fluorescence of the two compounds. The estimated precision was relative standard deviation (R.S.D.) <1.7%. The method was finally applied for the analysis of some sample fractions from an albumin standard used in affinity chromatography.     

Analysis of interferents by means a D-optimal screening design and calibration using partial least squares regression in the spectrophotometric determination of Cr(VI)

Using a central composite design, the signal of the process for the spectrophotometric determination of hexavalent chromium (λ = 543 nm) is maximised and its variability minimised using as complexing agent 1,5-diphenylcarbazide in sufficiently acid medium. To analyse the interference of various analytes (Mo(VI), V(V), Fe(III) and Mn(VII)) on the Cr(VI) as a function of concentration of interferent, a factorial design was prepared at three levels of each (zero, medium and high concentration), which implies performing 81 determinations. However, a D-optimal design with just nine experiments is sufficiently good to estimate the model proposed.The interference of these metals makes it impossible to determine Cr(VI) when they are present in the sample. To avoid prior separation steps, a multivariate regression by partial least squares, PLS, is proposed to calibrate the Cr(VI) in the presence of these analytes varying the concentration of the Cr(VI) between 0.1 and 0.9 μg ml⁻¹ and that of the interferents between 3 and 5 μg ml⁻¹. The average errors obtained were 4.5% and 3.29% fitted and in prediction, respectively, with a standard error in prediction (RMSEP) of 0.016% presenting absence of both constant and proportional bias.The detection limit with the PLS regression in the presence of interferents is 0.1 μg ml⁻¹ with a probability of false positive equal to 5% and less than 5% for false negative. The capability of detection is similar to that obtained with the univariate calibration (absorbance at 543 nm) in absence of interferents.With the PLS regression it is possible to discriminate 0.085 μg ml⁻¹ of Cr(VI) in a sample with 0.5 μg ml⁻¹ of Cr(VI) with probabilities of false compliance and false non-compliance equal to 0.05. For the univariate calibration without interferents, it was established at 0.0971 μg ml⁻¹ of Cr(VI) for the same nominal concentration.In relation to interference of V(V), Fe(III) and Mn(VII), the PLS calibration could be an efficient alternative to the separation step for Cr(VI) spectrophotometric determination using 1,5-diphenylcarbazide.     

Non-equilibrium determination of metoclopramide and tetracaine hydrochloride by sequential injection spectrophotometry

A new sequential injection spectrophotometric method was proposed for the determination of metoclopramide and tetracaine hydrochloride. The method was based on the detection of an unstable red intermediate compound resulting from the reaction of metoclopramide or tetracaine hydrochloride with potassium dichromate, in the presence of sodium oxalate, in sulfuric acid solution. The related reaction mechanisms of this new method have been studied. The experimental conditions were optimized for the stopped-flow and continuous-flow sequential injection models. For continuous flow, the linear range for determination of metoclopramide, the detection limit and the sampling frequency were 13-130 μg ml⁻¹, 9.4 μg ml⁻¹ and 40 samples per hour, respectively. For stopped flow, they were 3-42 μg ml⁻¹, 1.0 μg ml⁻¹ and 18 h⁻¹, respectively. Adopting the continuous-flow model for tetracaine hydrochloride, the linear range was 25-300 μg ml⁻¹, and the detection limit was 18.0 μg ml⁻¹ with sampling frequency of 40 h⁻¹. This method has been used to determine metoclopramide and tetracaine hydrochloride in pharmaceutical preparations, and the results are compared with those determined by the pharmacopoeia method. Statistical analysis reveals that there was no evidence of significant difference between the methods.     

Determination of thyroxine hormone by luminol chemiluminescence

A chemiluminescence (CL) flow system for determination of thyroxine (Thy) is presented. It is based on the catalytic effect of cobalt(II) on the CL reaction between luminol and hydrogen peroxide. The iodinated chemical structure of Thy causes a heavy atom effect. The luminol CL signals show significant quenching by Thy. The calibration graph for Thy is linear for 15-70 μg ml⁻¹ and the 3σ detection limits are 27 μg ml⁻¹ for d-Thy and 23 μg ml⁻¹ for l-Thy.     

Application of the spectral correction method and "neural networks" for simultaneous determination of V(V) and Al(III)

Simultaneous determination of V(V) and Al(III) was performed by application of neural networks when the calibration matrix was performed using β-correction spectra. Two reactions between V(V) and Al(III) and Alizarin Red S (ARS) as a ligand have been investigated and applied for the simultaneous spectrophotometric determination of these metal ions. The parameters controlling behavior of the system were investigated and optimum conditions selected. Feed-forward neural networks have been trained to quantify considered metal ions in mixtures under optimum conditions. Sigmoidal functions were used in the hidden and output layers. Determinations were made over the concentration range 0.10-7.80 μg ml⁻¹ of V(V) and 0.11-4.20 μg ml⁻¹ of Al(III). Applying this method satisfactorily to simultaneous determination of these metal ions in several synthetic solutions with total relative standard error less than 4.02% validated the proposed method.     

A environmentally friendly reversed-phase liquid chromatography method for phthalates determination in nail cosmetics

A simple and rapid analytical method was developed for the determination of phthalates, usually employed in nail cosmetic products. The method is based on an ultrasonic extraction of the sample with ethanol-water (90:10, v/v) followed by HPLC separation and quantitation. HPLC was carried out using a C18 column and spectrophotometric detection at 254 nm. A linear gradient elution was performed with ethanol-water starting from 50 to 95% ethanol in 30 min. Standard calibration curves were linear for all the analytes over the concentration range 5-200 μg ml⁻¹ with LOD values of about 0.5 μg ml⁻¹.The proposed green analytical method has been successfully applied for the analysis of commercial samples in order to check the presence of phthalates and to determine their concentration.     

Sequential flow injection analysis of ammonium and nitrate using gas phase molecular absorption spectrometry

A flow injection method on the basis of gas phase molecular absorption is described for the sequential determination of ammonium and nitrate. Two hundred microliters of sample solution is injected into the flow line. For ammonium determination, the sample zone is directed to a line in which reacts with NaOH (13 M) and produces ammonia. But for nitrate determination, the sample zone is passed through the on-line copperized zinc (Zn/Cu) reduction column and produces ammonium ion and in the follows ammonia. The produced ammonia in both cases is purged into the stream of N₂ carrier gas. The gaseous phase is separated from the liquid phase using a gas-liquid separator and then is swept into a flow through cell, which has been positioned in the cell compartment of an UV-Vis spectrophotometer. The absorbance of the gaseous phase is measured at 194 nm. Under selected conditions for sequential analysis of ammonium and nitrate, linear relations were found between the peak heights of absorption signals and concentrations of ammonium (10-650 μg ml⁻¹) and nitrate (20-800 μg ml⁻¹). The limit of detections for ammonium and nitrate analysis were 8 and 10 μg ml⁻¹, respectively. The relative standard deviations of repeated measurements of 50 μg ml⁻¹ of ammonium and nitrate were 2.0, 2.9%, respectively. Maximum sampling rate was about 40 samples/h. The method was applied to the determination of ammonium in pharmaceutical products and the sequential determination of ammonium and nitrate in spiked water samples.     

Determination of ternary mixtures of penicillin G, benzathine and procaine by liquid chromatography and factorial design study

In the present work, a rapid and sensitive method for simultaneous determination of penicillin G (PG), benzathine (BE) and procaine (PR) in drug and serum media is introduced. The polar hydro-organic (55/45) mobile phases containing an aqueous solution adjusted to pH = 3.7 and an organic solvent (MeOH) including triethylamine (TEA) and trifluroacetic acid (TFA) are used. The flow rate of 1 ml min⁻¹, a C₈ column (150 mm × 46 mm) with 5 μm i.d. and wavelength at 215 nm are selected for optimal separation condition. The limit of detection (LOD), linear concentration range and relative standard deviation (R.S.D.) of this method for the PG are 1.1 μg ml⁻¹, 10-2400 μg ml⁻¹ and 1.7% and for the BE are 1.2 μg ml⁻¹, 12-2100 μg ml⁻¹ and 1.8% and for the PR are 1.5 μg ml⁻¹, 20-2000 μg ml⁻¹ and 2%, respectively. The factorial design is used for the determination of main and interaction effects of pH, flow rate and concentration of MeOH, TEA and TFA in the separation at two levels. Also, the analysis of variance (ANOVA) table is obtained. The results show that TFA and TEA have higher effect than concentration of MeOH, pH and flow rate factors.     

Feasibility of ultra-high performance liquid and gas chromatography coupled to mass spectrometry for accurate determination of primary and secondary phthalate metabolites in urine samples

Phthalates (PAEs) are ubiquitous toxic chemical compounds. During the last few years, some phthalate metabolites (MPAEs) have been proposed as appropriate biomarkers in human urine samples to determine PAE human intake and exposure. So, it is necessary to have fast, easy, robust and validated analytical methods to determine selected MPAEs in urine human samples. Two different instrumental methods based on gas (GC) and ultra-high performance liquid (UHPLC) chromatography coupled to mass spectrometry (MS) have been optimized, characterized and validated for the simultaneous determination of nine primary and secondary phthalate metabolites in urine samples. Both instrumental methods have similar sensitivity (detection limits ranged from 0.03 to 8.89 pg μL⁻¹ and from 0.06 to 0.49 pg μL⁻¹ in GC–MS and UHPLC–MS², respectively), precision (repeatability, expressed as relative standard deviation, which was lower than 8.4% in both systems, except for 5OH-MEHP in the case of GC–MS) and accuracy. But some advantages of the UHPLC–MS² method, such as more selectivity and lower time in the chromatographic runs (6.8 min vs. 28.5 min), have caused the UHPLC–MS² method to be chosen to analyze the twenty one human urine samples from the general Spanish population. Regarding these samples, MEP showed the highest median concentration (68.6 μg L⁻¹), followed by MiBP (23.3 μg L⁻¹), 5cx-MEPP (22.5 μg L⁻¹) and MBP (19.3 μg L⁻¹). MMP (6.99 μg L⁻¹), 5oxo-MEHP (6.15 μg L⁻¹), 5OH-MEHP (5.30 μg L⁻¹) and MEHP (4.40 μg L⁻¹) showed intermediate levels. Finally, the lowest levels were found for MBzP (2.55 μg L⁻¹). These data are within the same order of magnitude as those found in other similar populations.     

Flow injection chemiluminescence determination of paracetamol

A simple chemiluminometric method using flow injection has been developed for the determination of paracetamol (acetaminophen), based on the chemiluminescence produced by the reduction of tris(2,2′-bipyridyl)ruthenium(III). The latter is obtained by oxidation of tris(2,2′-bipyridyl)ruthenium(II) by potassium permanganate in dilute sulphuric acid in the presence of paracetamol. A standard or sample solution was injected into the ruthenium(II) stream (flow rate 1.5 ml min⁻¹) which was then merged with potassium permanganate in dilute sulphuric acid stream (flow rate 0.5 ml min⁻¹). The chemiluminescence intensity is enhanced by the presence of manganese(II) ions. Under the optimum conditions, a linear calibration graph was obtained over the range of 0.3-50.0 μg ml⁻¹ and the detection limit was 0.2 μg ml⁻¹ (s/n = 3). The relative standard deviation of the proposed method calculated from 20 replicate injections of 5.0 μg ml⁻¹ paracetamol was 1.1%. The sample throughput was 90 h⁻¹. The method was successfully applied to the determination of paracetamol in commercial pharmaceutical formulations.     

Simultaneous determination of bromine and chlorine in coal using electrothermal vaporization inductively coupled plasma mass spectrometry and direct solid sample analysis

A new method for the direct analysis of coal using electrothermal vaporization inductively coupled plasma mass spectrometry and direct solid sample analysis was developed, aiming at the determination of Br and Cl. The procedure does not require any significant sample pretreatment and allows simultaneous determination of both elements to be carried out, requiring small mass aliquots of sample (about 0.5 mg). All operating parameters, including carrier gas flow-rate and RF power, were optimized for maximum sensitivity. The use of modifiers/aerosol carriers (Pd, Pd + Al and Pd + Ca) was evaluated, and the mixture of Pd and Ca was chosen, allowing pyrolysis and vaporization temperatures of 700 °C and 1900 °C, respectively. Chlorine was accurately determined using calibration against solid standards, whereas Br could also be determined using calibration against aqueous standard solutions. The limits of quantification were 0.03 μg g⁻¹ for Br and 7 μg g⁻¹ for Cl, and no spectral interferences were observed.