A novel amperometric sensor for the detection of difenidol hydrochloride based on the modification of Ru(bpy)3 on a glassy carbon electrode

An amperometric sensor for the detection of difenidol, a tertiary amine-containing analyte, was proposed. Ruthenium(II) tris(bipyridine)/multi-walled carbon nanotubes/Nafion composite film was suggested to modify the glassy carbon electrode. The modified electrode was shown to be an excellent amperometric sensor for the detection of difenidol hydrochloride. The linear range is from 1.0 × 10⁻⁶ to 3.3 × 10⁻⁵ M with a correlation coefficient of 0.998. The limit of detection was 5 × 10⁻⁷ M, which was obtained through experimental determination based on a signal-to-noise ratio of three. The sensor was employed to the determination of the active ingredients in the tablets containing difenidol hydrochloride.     

Post-column detection of benzenediols and 1,2,4-benzenetriol based on acidic potassium permanganate chemiluminescence

Based on the sensitizing effect of formic acid on the chemiluminescence (CL) reaction of polyhydroxylbenzenes with acidified potassium permanganate and the combination technique of high-performance liquid chromatography (HPLC), a sensitive, selective and simple post-column CL detection method for simultaneously determining catechol, resorcinol, hydroquinone and 1,2,4-benzenetriol is described. The optimal conditions for the CL detection and HPLC separation were carried out. The linear ranges were: 6.0 × 10⁻³-1.5 mg/L for hydroquinone, 8.0 × 10⁻³-1.5 mg/L for 1,2,4-benzenetriol, 1.0 × 10⁻²-2.0 mg/L for resorcinol and 1.0 × 10⁻²-2.5 mg/L for catechol, respectively. The detection limits are: 3.2 × 10⁻³ mg/L for hydroquinone, 3.9 × 10⁻³ mg/L for 1,2,4-benzenetriol, 4.7 × 10⁻³ mg/L for resorcinol and 5.2 × 10⁻³ mg/L for catechol, respectively. Combining with solid phase extraction, the proposed method has been successfully applied to the determination of the polyhydroxylbenzenes in river water. The recoveries for three benzentriols were 92.1-95.4% and 82.0% for 1,2,4-benzenetriol, respectively.     

Flow injection fluorescence determination of dopamine using a photo induced electron transfer (PET) boronic acid derivative

An automated flow injection analysis system was developed for the fluorometric determination of dopamine in pharmaceutical injections. The method is based on the quenching effect of dopamine on m-dansylaminophenyl boronic acid (DAPB) fluorescence due to the reverse photo induced electron transfer (PET) mechanism. Effects of pH and interfering species on the determination of dopamine were examined. Calibration for dopamine, based on quenching data, was linear in the concentration range of 1.0 × 10⁻⁵ to 1.0 × 10⁻⁴ M. Detection limit (3 s) of the method was found to be 3.7 × 10⁻⁶ M. Relative standard deviation of 1.2% (n = 10) was obtained with 1.0 × 10⁻⁵ M dopamine standard solution. The proposed method was applied successfully for the determination of dopamine in pharmaceutical injection sample. The sampling rate was determined as 24 samples per hour.     

Highly selective and sensitive thiocyanate membrane electrode based on nickel(II)-1,4,8,11,15,18,22,25-octabutoxyphthalocyanine

A highly selective membrane electrode based on nickel(II)-1,4,8,11,15,18,22,25-octabutoxyphthalocyanine (NOBP) is presented. The proposed electrode shows very good selectivity for thiocyanate ions over a wide variety of common inorganic and organic anions. The sensor displays a near Nernstian slope of −58.7 ± 0.6 mV per decade. The working concentration range of the electrode is 1.0 × 10⁻⁶ to −1.0 × 10⁻¹ M with a detection limit of 5.7 × 10⁻⁷ M (33.06 ng/mL). The response time of the sensor in whole concentration ranges is very short (<10 s). The response of the sensor is independent on the pH range of 4.3-9.8. The best performance was obtained with a membrane composition of 30% PVC, 65% dibutyl phthalate, 3% NOBP and 2% hexadecyltrimethylammonium bromide. It was successfully applied to direct determination of thiocyanate in biological samples, and as an indicator electrode for titration of thiocyanate ions with AgNO₃ solution.     

Time measurement-visual analysis of l-cysteine using the autocatalytic sodium sulfite/hydrogen peroxide reaction system and its application to length detection-flow analysis

Trace amounts of l-cysteine can function as a trigger, i.e., reaction initiator, in the autocatalytic sodium sulfite/hydrogen peroxide reaction system. Rapidly changing of pH after induction time is visually confirmed by color changing of bromothymol blue in this autocatalytic reaction. Based on this finding, μg L⁻¹ levels of l-cysteine were measured over time using the autocatalytic reaction system. The determination range using the above method was 5.0 × 10⁻⁸-2.5 × 10⁻⁶ M, the detection limit (3σ) was 1.8 × 10⁻⁸ M (1.94 μg L⁻¹), and the relative standard deviation was 2.41% at an l-cysteine concentration of 5 × 10⁻⁷ M (n = 5). This method was also applied to length detection-flow injection analysis. The determination range for the flow injection analysis was 2.0 × 10⁻⁷-1.0 × 10⁻⁵ M. The detection limit (3σ) was 1.4 × 10⁻⁷ M (17.0 μg L⁻¹), and the relative standard deviation was 0.91% at an initial l-cysteine concentration of 10⁻⁶ M (n = 5).     

Ionic liquid-based miniature electrochemical sensors for the voltammetric determination of catecholamines

Screen-printed electrodes modified with carbon paste that consisted of graphite powder dispersed in ionic liquids (IL) were used for the electrochemical determination of dopamine, adrenaline and dobutamine in aqueous solutions by means of cyclic voltammetry. The IL plays a dual role in modifying compositions, acting both as a binder and chemical modifier (ion-exchanger); ion-exchange analyte pre-concentration increases analytical signal and improves the sensitivity. Calibration graphs are linear in concentration range 3.9 × 10⁻⁶ to 1.0 × 10⁻⁴ M (dopamine), 2.9 × 10⁻⁷ to 1.0 × 10⁻⁴ M (adrenaline) and 1.7 × 10⁻⁷ to 1.0 × 10⁻⁴ M (dobutamine); detection limits are (1.2 ± 0.1) × 10⁻⁶, (1.3 ± 0.1) × 10⁻⁷ and (5.3 ± 0.1) × 10⁻⁸ M, respectively. Using an additive of Co (III) tetrakis-(tert-butyl)-phthalocyanine leads to the increase of signal and lowering detection limit. Some practical advises concerning both the sensor design and selectivity of catecholamine determination are provided.     

Study on the interaction of nucleic acids with silver nanoparticles—Al(III) by resonance light scattering technique and its analytical application

It is found that Al(III) can further enhance the intensity of resonance light scattering (RLS) of the silver nanoparticles (AgNPs) and nucleic acids system. Based on this, a novel method of determination of nucleic acids is proposed in this paper. Under optimum conditions, there are linear relationships between the enhancing extent of RLS and the concentration of nucleic acids in the range of 1.0 × 10⁻⁹-1.0 × 10⁻⁷ g mL⁻¹, 1.0 × 10⁻⁷-2.0 × 10⁻⁶ g mL⁻¹ for fish sperm DNA (fsDNA), 1.0 × 10⁻⁹-7.0 × 10⁻⁸ g mL⁻¹ for calf thymus DNA (ctDNA) and 1.0 × 10⁻⁹-1.0 × 10⁻⁷ g mL⁻¹ for yeast RNA (yRNA). The detection limits (S/N = 3) of fsDNA, ctDNA and yRNA are 4.1 × 10⁻¹⁰ g mL⁻¹, 4.0 × 10⁻¹⁰ g mL⁻¹ and 4.5 × 10⁻¹⁰ g mL⁻¹, respectively. The studies indicate that the RLS enhancement effect should be ascribed to the formation of AgNPs-Al(III)-DNA aggregations through electrostatic attraction and adsorption bridging action of Al(III). And the sensitivity and stability of the AgNPs-fsDNA system could be enhanced by Al(III).     

Characterization of gold-thiol-8-hydroxyquinoline self-assembled monolayers for selective recognition of aluminum ion using voltammetry and electrochemical impedance spectroscopy

Gold electrode surface is modified via covalent attachment of a synthesized thiol functionalized with 8-hydroxyquinoline, p-((8-hydroxyquinoline)azo) benzenethiol (SHQ), for the first time. The behavior of the nanostructured electrode surface (Au–SHQ) is characterized by electrochemical techniques including cyclic and differential pulse voltammetry (CV and DPV), and electrochemical impedance spectroscopy (EIS). The modified surface is stable in a wide range of potentials and pHs. A surface pK_a of 6.0 ± 0.1 is obtained for Au–SHQ electrode using surface acid/base titration curves constructed by CV and EIS measurements as a function of pH. These results helped to determine the charge state of the surface as a function of pH. The gold modified electrode surface showed good affinity for sensing the Al(III) ion at pH 5.5. The sensing process is based on (i) accumulation and complex formation between Al(III) from the solution phase and 8HQ function on the Au electrode surface (recognition step) and (ii) monitoring the impedance of the Au–SHQ–Al(III) complex against redox reaction rate of parabenzoquinone (PBQ) (signal transduction step). The PBQ is found to be a more suitable probe for this purpose, after testing several others. Thus, the sensor was tested for quantitative determination of Al(III) from the solution phase. At the optimized conditions, a linear response, from 1.0 × 10⁻¹¹ to 1.2 × 10⁻⁵ M Al(III) in semi-logarithmic scale, with a detection limit of 8.32 × 10⁻¹² M and mean relative standard deviation of 3.2% for n = 3 at 1.0 × 10⁻⁷ M Al(III) is obtained. Possible interferences from coexisting cations and anions are also studied. The results show that many ions do not interfere significantly with the sensor response for Al(III). Validity of the method and applicability of the sensor are successfully tested by determination of Al(III) in human blood serum samples.     

Single-walled carbon nanohorn as new solid-phase extraction adsorbent for determination of 4-nitrophenol in water sample

Single-walled carbon nanohorn (SWCNH) was developed as new adsorbent for solid-phase extraction using 4-nitrophenol as representative. The unique exoteric structures and high surface area of SWCNH allow extracting a large amount of 4-nitrophenol over a short time. Highly sensitive determination of 4-nitrophenol was achieved by linear sweep voltammetry after only 120 s extraction. The calibration plot for 4-nitrophenol determination is linear in the range of 5.0 × 10⁻⁸ M-1.0 × 10⁻⁵ M under optimum conditions. The detection limit is 1.1 × 10⁻⁸ M. The proposed method was successfully employed to determine 4-nitrophenol in lake water samples, and the recoveries of the spiked 4-nitrophenol were excellent (92-106%).     

A capacitive immunosensor for detection of cholera toxin

Contamination of food with biological toxins as well as their potential use as weapons of mass destruction has created an urge for rapid and cost effective analytical techniques capable of detecting trace amounts of these toxins. This paper describes the development of a sensitive method for detection of cholera toxin (CT) using a flow-injection capacitive immunosensor based on self-assembled monolayers. The sensing surface consists of monoclonal antibodies against the B subunit of CT (anti-CT), immobilized on a gold transducer. Experimental results show that the immunosensor responded linearly to CT concentrations in the range from 1.0 × 10⁻¹³ to 1.0 × 10⁻¹⁰ M under optimized conditions. The limit of detection (LOD) was 1.0 × 10⁻¹⁴ M. Two more analytical methods were employed for detection of CT using the same antibody namely, sandwich ELISA and surface plasmon resonance (SPR)-based immunosensor. The former had an LOD of 1.2 × 10⁻¹² M and a working range from 3.7 × 10⁻¹¹ to 2.9 × 10⁻¹⁰ M whereas, the later had an LOD of 1.0 × 10⁻¹¹ M and a linearity ranging from 1.0 × 10⁻⁹ to 1.0 × 10⁻⁶ M. These results demonstrate that the developed capacitive immunosensor system has a higher sensitivity than the other two techniques. The binding affinity of CT to the immobilized anti-CT was determined using the SPR-based immunosensor and an association constant (K_A) of 1.4 × 10⁹ M⁻¹ was estimated.     

Highly selective and sensitive monohydrogen phosphate membrane sensor based on molybdenum acetylacetonate

In this work, a highly selective and sensitive monohydrogen phosphate membrane sensor based on a molybdenum bis(2-hydroxyanil) acetylacetonate complex (MAA) is reported. The sensor shows a linear dynamic range between 1.0 × 10⁻¹ and 1.0 × 10⁻⁷ M, with a nice Nernstian behavior (−29.5 ± 0.3 mV decade⁻¹) in pH of 8.2. The detection limit of the electrode is 6.0 × 10⁻⁸ M (∼6 ppb). The best performance was obtained with a membrane composition of 32% poly(vinyl chloride), 58% benzyl acetate, 2% hexadecyltrimethylammonium bromide and 8% MAA. The sensor possesses the advantages of short response time, low detection limit and especially, very good selectivity towards a large number of organic and inorganic anions including salicylate, citrate, tartarate, acetate, oxalate, fluoride, chloride, bromide, iodide, sulfite, sulfate, nitrate, nitrite, cyanide, thiocyanate, perchlorate, metavanadate, and bicarbonate ions. The electrode can be used for at least 10 weeks without any considerable divergence in its slope and detection limit. It was used as an indicator electrode in potentiometric titration of monohydrogenphosphate ion with barium chloride. The proposed sensor was successfully applied to direct determination of monohydrogenphosphate in two fertilizer samples (NPK).     

Determination of cysteine in a pharmaceutical formulation by flow injection analysis with a chemiluminescence detector

A simple and convenient flow injection-chemiluminescence (FI-CL) method for the determination of cysteine is reported, based on a fast and strong CL in a basic luminol-cysteine-NaIO₄ solution. The linear range was 1.0×10⁻⁸ to 1.0×10⁻⁶ M with a detection limit (3s) of 5×10⁻⁹ M, which was 100 times more sensitive than previously reported CL methods. Singlet oxygen, hydroxyl radical and hydrogen peroxide were suggested to be produced in this reaction and were responsible for the CL of cysteine. This simple method has been successfully applied for the determination of cysteine in a pharmaceutical formulation.     

Disposable biosensor based on cathodic electrochemiluminescence of tris(2,2-bipyridine)ruthenium(II) for uric acid determination

A new method for uric acid (UA) determination based on the quenching of the cathodic ECL of the tris(2,2-bipyridine)ruthenium(II)–uricase system is described. The biosensor is based on a double-layer design containing first tris(2,2-bipyridine)ruthenium(II) (Ru(bpy)₃²⁺) electrochemically immobilized on graphite screen-printed cells and uricase in chitosan as a second layer. The uric acid biosensing is based on the ECL quenching produced by uric acid over the cathodic ECL caused by immobilized Ru(bpy)₃²⁺ in the presence of uricase. The use of a −1.1 V pulse for 1 s with a dwelling time of 10 s makes it possible to estimate the initial enzymatic rate, which is used as the analytical signal. The Stern–Volmer type calibration function shows a dynamic range from 1.0 × 10⁻⁵ to 1.0 × 10⁻³ M with a limit of detection of 3.1 × 10⁻⁶ M and an accuracy of 13.6% (1.0 × 10⁻⁴ M, n = 5) as relative standard deviation. Satisfactory results were obtained for urine samples, creating an affordable alternative for uric acid determination.     

Preliminary evaluation of monolithic column high-performance liquid chromatography with tris(2,2′-bipyridyl)ruthenium(II) chemiluminescence detection for the determination of quetiapine in human body fluids

High-performance liquid chromatography (HPLC) with tris(2,2′-bipyridyl)ruthenium(II) chemiluminescence detection methodology is reported for the determination of the atypical antipsychotic drug quetiapine and the observation of its major active and inactive metabolites in human urine and serum. The method uses a monolithic chromatographic column allowing high flow rates of 3 mL min⁻¹ enabling rapid quantification. Flow injection analysis (FIA) with tris(2,2′-bipyridyl)ruthenium(II) chemiluminescence detection and HPLC time of flight mass spectrometry (TOF-MS) were used for the determination of quetiapine in a pharmaceutical preparation to establish its suitability as a calibration standard. The limit of detection achieved with FIA was 2 × 10⁻¹¹ mol L⁻¹ in simple aqueous solution. The limits of detection achieved with HPLC were 7 × 10⁻⁸ and 2 × 10⁻¹⁰ mol L⁻¹ in urine and serum, respectively. The calibration range for FIA was between 5 × 10⁻⁹ and 1 × 10⁻⁶ mol L⁻¹. The calibration ranges for HPLC were between 1 × 10⁻⁷-1 × 10⁻⁴ and 1 × 10⁻⁸-1 × 10⁻⁴ mol L⁻¹ in urine and serum, respectively. The quetiapine concentrations in patient samples were found to be 3 × 10⁻⁶ mol L⁻¹ in urine and 7 × 10⁻⁷ mol L⁻¹ in serum. Without the need for preconcentration, the HPLC detection limits compared favourably with those in previously published methodologies. The metabolites were identified using HPLC-TOF-MS.     

A selective modified carbon paste electrode for determination of cyanide using tetra-3,4-pyridinoporphyrazinatocobalt(II)

A chemically modified carbon paste electrode with 3,4-tetra pyridinoporphirazinatocobalt(II) (Co(3,4 tppa) was applied to the determination of free cyanide ion. The electrode has a linear range between 1.5 × 10⁻⁵ M and 1.0 × 10⁻² M with a Nernstian slope of 60 ± 1.5 mV/decade and its detection limit is 9 × 10⁻⁶ M. The response time of electrode is 5 min. The proposed electrode was applied successfully for the determination of cyanide in commercially available spring water. Some anions, such as SCN⁻, I⁻, Cl⁻, Br⁻ and oxalate that are usually serious interfering species for most of cyanide selective electrodes, did not have any interfering effect for this proposed electrode.     

Determination of levodopa by capillary electrophoresis with chemiluminescence detection

A rapid and simple method using capillary electrophoresis (CE) with chemiluminescence (CL) detection was developed for the determination of levodopa. This method was based on enhance effect of levodopa on the CL reaction between luminol and potassium hexacyanoferrate(III) (K₃[Fe(CN)₆]) in alkaline aqueous solution. CL detection employed a lab-built reaction flow cell and a photon counter. The optimized conditions for the CL detection were 1.0 × 10⁻⁵ M luminol added to the CE running buffer and 5.0 × 10⁻⁵ M K₃[Fe(CN)₆] in 0.6 M NaOH solution introduced postcolumn. Under the optimal conditions, a linear range from 5.0 × 10⁻⁸ to 2.5 × 10⁻⁶ M (r = 9991), and a detection limit of 2.0 × 10⁻⁸ M (signal/noise = 3) for levodopa were achieved. The precision (R.S.D.) on peak area (at 5.0 × 10⁻⁷ M of levodopa, n = 11) was 4.1%. The applicability of the method for the analysis of pharmaceutical and human plasma samples was examined.     

Synthesis and analytical application of a novel tetradentate N(2)O(2) Schiff base as a chromogenic reagent for determination of nickel in some natural food samples

A novel sensitive chromogenic reagent, N,N′-bis(3-methylsalicylidene)-ortho-phenylene diamine (MSOPD), has been synthesized and used in the spectrophotometric determination of nickel. At pH 8, MSOPD can react with nickel ion at room temperature to form a 1:1 complex. The apparent molar absorptivity is 9.5 × 10⁴ l mol⁻¹ cm⁻¹ at 430 nm. Beer's low is obeyed over the range 0-1.0 × 10⁻⁵ M of nickel with a detection limit of 1.36 × 10⁻⁸ M. The relative standard deviation for measurement of 3.41 × 10⁻⁶ M nickel is 1.3% (n = 10). The method has successfully been applied to determination of trace amounts of nickel in some natural food samples.     

Analysis of parabens in cosmetics by low pressure liquid chromatography with monolithic column and chemiluminescent detection

This paper presents an application of chromatographic separation based on an ultra-short monolithic column and chemiluminescent detection in an FIA type instrument manifold for the determination of four paraben mixtures: methylparaben (MP), ethylparaben (EP), propylparaben (PP) and butylparaben (BP). The separation is achieved in 150 s using two consecutive carriers: first 12% ACN:water that changes 75 s after injection to 27% ACN:water. The detection is based on the oxidation of the hydrolysis product of parabens, p-hydroxybenzoic acid, with Ce(IV) in the presence of Rhodamine 6G which evokes chemiluminescence of sufficient intensity to enable a sensitive determination of these species. After optimization of the variables involved, the analytical method is characterized, displaying the following values for concentration ranges, detection limits and precision, as relative standard deviation at low concentration (0.15 mg l⁻¹)—MP: from 9.9 × 10⁻⁷ to 3.3 × 10⁻⁴ M; 1.9 × 10⁻⁸; 5.6%; EP: from 9.0 × 10⁻⁷ to 3.3 × 10⁻⁴ M; 2.8 × 10⁻⁸; 3.5%; PP: from 8.3 × 10⁻⁷ to 9.9 × 10⁻⁵ M; 2.3 × 10⁻⁸; 4.2%; and BP: from 7.7 × 10⁻⁷ to 9.9 × 10⁻⁵ M; 4.2 × 10⁻⁸ M; 6.2%. The method was applied and validated satisfactorily for the determination of these parabens in cosmetic samples, comparing the results against a liquid chromatography reference method.     

Polyethyleneimine-capped silver nanoclusters as a fluorescence probe for sensitive detection of hydrogen peroxide and glucose

In this work, we utilized polyethyleneimine-capped silver nanoclusters (PEI-Ag nanoclusters) to develop a new fluorometric method for the determination of hydrogen peroxide and glucose with high sensitivity. The PEI-Ag nanoclusters have an average size of 2 nm and show a blue emission at 455 nm. The photostable properties of the PEI-Ag nanoclusters were examined. The fluorescence of the PEI-Ag nanoclusters could be particularly quenched by H₂O₂. The oxidization of glucose by glucose oxidase coupled with the fluorescence quenching of PEI-Ag nanoclusters by H₂O₂ can be used to detect glucose. Under optimum conditions, the fluorescence intensity quenched linearly in the range of 500 nM–100 μM with high sensitivity. The detection limit for H₂O₂ was 400 nM. And a linear correlation was established between fluorescence intensity (F₀ − F) and concentration of glucose in the range of 1.0 × 10⁻⁶ to 1.0 × 10⁻⁵ M and 1.0 × 10⁻⁵ to 1.0 × 10⁻³ M with a detection limit of 8.0 × 10⁻⁷ M. The method was used for the detection of glucose in human serum samples with satisfactory results. Furthermore, the mechanism of sensitive fluorescence quenching response of Ag nanoclusters to glucose and H₂O₂ has been discussed.     

Determination of l-histidine by modified carbon paste electrode using tetra-3,4-pyridinoporphirazinatocopper(II)

This paper describes a potentiometric method for determination of l-histidine (l-his) in aqueous media, using a carbon paste electrode modified with tetra-3,4-pyridinoporphirazinatocopper(II) (Cu (3,4tppa)). The electrode exhibits linear response to the logarithm of the concentration of l-histidine from 2.4 × 10⁻⁵ to 1.0 × 10⁻² M, with a response slope of −49.5 ± 1 mV and response time of about 1.5 min. The detection limit according to IUPAC recommendation was 2.0 × 10⁻⁵ M. The proposed electrode shows a good selectivity for l-his over a wide variety of anions. This chemically modified carbon paste electrode was successfully used for the determination of l-his in a synthetic serum and RANDOX control serum solutions.